Table Of Contents

Mapping ACNS Software CLI Commands to the Content Distribution Manager GUI

CLI Commands Supported in the Content Distribution
Manager GUI

CLI Commands Not Supported in the Content Distribution Manager GUI

Mapping ACNS Software CLI Commands to the Content Distribution Manager GUI

---

This appendix lists the CLI commands that are supported and unsupported in the ACNS 5.5 Content Distribution Manager GUI. It contains the following sections:

•CLI Commands Supported in the Content Distribution Manager GUI

•CLI Commands Not Supported in the Content Distribution Manager GUI

CLI Commands Supported in the Content Distribution
Manager GUI

Table C-1 maps ACNS software CLI commands to the corresponding Content Distribution Manager GUI procedure. Software CLI commands are listed in alphabetical order in the first column. The second column indicates the GUI navigation path to the device group configuration window for each command. The third column provides a link to the GUI configuration procedure found elsewhere in this guide. In most cases, the procedure provides an illustration of the configuration window and a table at the end of the procedure that maps each field in the GUI window to its corresponding CLI command.

---

Note Most of the procedures in this guide document the configuration steps for individual devices, whereas this table provides the GUI navigation path to the device group configuration window, unless otherwise indicated. The procedures for configuring device groups and individual devices are the same in most cases.

---

Table C-1 ACNS Software CLI to Content Distribution Manager GUI Map 

Command	GUI Navigation Path	Procedure Reference
aaa accounting {commands {0 | 15} default {start-stop | stop-only | wait-start} tacacs | exec default {start-stop | stop-only | wait-start} tacacs | system default {start-stop | stop-only} tacacs}	Devices > Device Groups > General Settings > Authentication > AAA Accounting	Configuring AAA Accounting, page 12-27
access-lists 300 {deny groupname {any [position number] | groupname [position number]}} | {permit groupname {any [position number] | groupname [position number]}}	Devices > Devices1 > General Settings > Authentication > Access List > Configure Access Control List	Configuring an Access Control List for Group Authorization, page 18-1
access-lists enable	Devices > Devices > General Settings > Authentication > Access List > Enable Access Control List	Enabling the Access Control List, page 18-2
acquirer proxy authentication outgoing ipaddress port_num username [password password] [ntlm domain [basic-auth-disable]]	Devices > Device Groups > Applications > Web > HTTP > HTTP Connections	Configuring Authentication for an HTTP Proxy Using the Content Distribution Manager GUI, page 6-44
acquirer proxy authentication transparent username [password password] [ntlm domain [basic-auth-disable]]	Devices > Device Groups > Prepositioning > Acquirer WCCP Proxy Authentication	Configuring Authentication for a WCCP Proxy Using the Content Distribution Manager GUI, page 6-46
asset tag name	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Asset Tag	Configuring SNMP Asset Tag Settings, page 22-11
authentication {configuration | login} {local | radius | tacacs} enable primary [secondary | tertiary]	Devices > Device Groups > General Settings > Authentication > Login Authentication	Configuring Devices for Login Authentication and Authorization, page 12-7
authentication fail-over server-unreachable
bandwidth {real-proxy {incoming kbits | outgoing kbits} | real-server kbits | wmt {incoming kbits | outgoing kbits} | cisco-streaming-engine kbits | http kbits} {start-time weekday time end-time weekday time}	Devices > Device Groups > Applications > Bandwidth Schedules	Configuring Scheduled Bandwidth Settings, page 9-42
bandwidth {real-proxy {incoming kbits | outgoing kbits} | real-server kbits | wmt {incoming kbits | outgoing kbits} | cisco-streaming-engine kbits | http kbits} {default | max-bandwidth}	Devices > Device Groups > Applications > Default and Maximum Bandwidth	Configuring Content Services Default and Maximum Bandwidth Settings, page 9-41
banner {motd | login | exec} message message_text banner enable	Devices > Device Groups > General Settings > Login Access Control > Message of the Day	Configuring Message of the Day Settings for the Content Engine, page 20-5
bitrate http default bitrate	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
bitrate wmt incoming bitrate
bitrate wmt outgoing bitrate
bypass auth-traffic enable	Devices > Device Groups > Request Routing > WCCP > Bypass	Configuring WCCP Bypass Settings, page 4-23
bypass load {enable | in-interval seconds | out-interval seconds | time-interval minutes}
bypass static {clientip {serverip | any-server} | any-client serverip}	Devices > Device Groups > Request Routing > WCCP > Bypass List	Creating WCCP Bypass List Entries, page 4-25
bypass timer minutes	Devices > Device Groups > Request Routing > WCCP > Bypass	Configuring WCCP Bypass Settings, page 4-23
bypass gateway ipaddress
error-handling {reset-connection | send-cache-error | transparent}
cdp enable	Devices > Device Groups > General Settings > Services > CDP	Configuring CDP Settings, page 20-7
cdp holdtime seconds
cdp timer seconds
clock timezone timezone offset	Devices > Device Groups > General Settings > Services > Date/Time > Time Zone	Configuring Device Clock and Time Zone Settings, page 20-12
clock summertime timezone {date | recurring}
cms database maintenance full enable	Devices > Device Groups > General Settings > Services > Database Maintenance	See the Cisco ACNS Software Update and Maintenance Guide, Release 5.x
cms database maintenance full schedule {every-day | weekday at time}
cms database maintenance regular enable
cms database maintenance regular schedule {every-day | weekday at time}
Content Router global configuration command: contentrouting leastloaded	Devices > Devices > Device Activation	Enabling Load-Based Routing on the Content Router, page 4-55
contentrouting servicemonitor {numberofsamples {all number | cpu number | disk number | wmt number} | sampleperiod {all seconds | cpu seconds | disk seconds | wmt seconds} | threshold {cpu percentage | wmt percentage} | type {all | cpu | disk | wmt}}	Devices > Device Groups > General Settings > Notification and Tracking > Service Monitor	Configuring Content Engine Threshold Limits for Load-Based Routing, page 4-56
dns min-ttl seconds	Devices > Devices1 > Applications > DNS > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
dns max-ttl seconds
dns user-expired enable
dns max-cache-memory mbytes	Devices > Device Groups > General Settings > Services > DNS	Configuring the DNS Server for HTTP Proxy Caching, page 8-78
	Devices > Devices1 > Applications > DNS > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
dns enable	Devices > Device Groups > General Settings > Services > DNS	Configuring the DNS Server for HTTP Proxy Caching, page 8-78
	Devices > Devices1 > Applications > DNS > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
dns listen {all | ipaddress} port port_num hostname hostname	Devices > Devices1 > Applications > DNS > DNS Server Binding	Configuring DNS Server Bindings for the Content Engine, page 8-75
dns use-original-server {only | after-configured | before-configured}	Devices > Devices1 > Applications > DNS > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
dns pin {forward hostname ipaddress | reverse hostname ipaddress | both hostname ipaddress | cname records}	Devices > Device Groups > Request Routing > DNS > A-Record Mapping	Configuring DNS Address Record Mappings for the Content Engine, page 8-76
	Devices > Device Groups > Request Routing > DNS > CNAME Record Mapping	Configuring DNS Canonical Name Record Mappings for the Content Engine, page 8-77
dns retry-period seconds	Devices > Devices1 > Applications > DNS > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
dns retry-timeout seconds
dns serial-lookup	Devices > Device Groups > General Settings > Services > DNS	Configuring the DNS Server for HTTP Proxy Caching, page 8-78
	Devices > Devices1 > Applications > DNS > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
exec-timeout minutes	Devices > Device Groups > General Settings > Login Access Control > Exec Timeout	Configuring Exec Timeout Settings, page 20-6
ftp-native access-list {in | out} {std_acl_number | acl_name}	Devices > Devices > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application, page 17-12
EXEC mode ftp-native custom-message {download {acl-denied url | welcome url} | reset {acl-denied | all | welcome} | upload host directory filename {welcome | acl-denied}}	Devices > Devices > Applications > Web > FTP > FTP Messages > Upload Devices > Device Groups > Applications > Web > FTP > FTP Messages > Download	Configuring Native FTP Custom Messages, page 8-62
ftp-native object max-size kilobytes	Devices > Device Groups > Applications > Web > FTP > Native FTP Cache Freshness	Configuring Native FTP Cache Freshness, page 8-61
ftp-native proxy active-mode enable	Devices > Device Groups > Applications > Web > FTP > Native FTP Connections	Configuring Native FTP Connections, page 8-58
ftp-native proxy authentication enable
ftp-native proxy incoming portnum
ftp-over-http age-multiplier directory-listing dl_time file fo_time	Devices > Device Groups > Applications > Web > FTP > FTP Over HTTP Cache Freshness	Configuring FTP-Over-HTTP Cache Freshness, page 8-55
ftp-over-http max-ttl {days directory-listing dlmax_days file fmax_days | hours directory-listing dlmax_hours file fmax_hours | minutes directory-listing dlmax_min file fmax_min | seconds directory-listing dlmax_sec file fmax_sec}
ftp-over-http min-ttl min_minutes
ftp-over-http object max-size size
ftp-over-http proxy incoming ports	Devices > Device Groups > Applications > Web > FTP > FTP Over HTTP Connections	Configuring FTP-Over-HTTP Connection Settings, page 8-52
ftp-over-http proxy outgoing origin-server
ftp-over-http proxy outgoing connection-timeout
ftp-over-http proxy outgoing monitor
ftp-over-http proxy outgoing host {hostname | ipaddress} port
ftp-over-http proxy anonymous-pswd passwd
ftp-over-http proxy active-mode enable
ftp-over-http reval-each-request {all | none | directory-listing}	Devices > Device Groups > Applications > Web > FTP > FTP Over HTTP Cache Freshness	Configuring FTP-Over-HTTP Cache Freshness, page 8-55
gui-server enable	Devices > Device Groups > General Settings > Login Access Control > GUI Server	Configuring the Content Engine GUI for Secure or Nonsecure Access, page 16-59
gui-server secure enable
gui-server port port_num
gui-server secure port port_num
hostname name	Devices > Devices > Device Activation	Modifying Content Engine Properties, page 13-9
http add-method method	Devices > Device Groups > Applications > Web > HTTP > HTTP Method	Adding or Modifying Additional HTTP Request Methods for the Content Engine, page 8-23
http age-multiplier text num binary num	Devices > Device Groups > Applications > Web > HTTP > HTTP Cache Freshness	Configuring HTTP Cache Freshness Settings, page 8-10
http always-resolve-host	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http anonymizer enable
http append via-header	Devices > Device Groups > Applications > Web > HTTP > Authenticated HTTP Caching	Configuring Authenticated HTTP Cache Settings, page 8-13
http append host-header
http append x-forwarded-for-header
http append x-forwarded-for-header multiple-ip-address
http append proxy-auth-header {ipaddress | hostname}
http append www-auth-header {hostname | ipaddress}
http authenticate-strip-ntlm
http authentication cache timeout minutes	Devices > Device Groups > Applications > Web > HTTP > Authenticated HTTP Caching	Configuring Authenticated HTTP Cache Settings, page 8-13
http authentication cache max-entries entries
http authentication header {401 | 407}
http authentication realm line
http cache-authenticated basic
http cache-authenticated ntlm
http cache-authenticated all
http cache-cookies	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http cache-on-abort enable	Devices > Device Groups > Applications > Web > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings, page 8-19
http cache-on-abort max-threshold max_thresh
http cache-on-abort min-threshold min_thresh
http cache-on-abort percent percenthresh
http cache-vary-user-agent sub-string string cache-string string	Devices > Device Groups > Applications > Web > HTTP > HTTP Cache User Agent	Configuring HTTP Cache Vary User Agent, page 8-25
http cache-vary-user-agent enable	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http client-no-cache-request {ignore | revalidate}
http cluster max-delay seconds	Devices > Device Groups > Applications > Web > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings, page 8-19
http cluster misses num
http cluster http-port num
http cluster heal-port num
http destination-port {allow | deny}	Devices >Device Groups > Web > HTTP > HTTP Destination Port Restrictions	Configuring HTTP Destination Port Restrictions, page 8-26
http dns-cache size max-num	Devices > Device Groups > Request Routing > DNS Caching > DNS Caching Server	Configuring DNS Caching Server Settings for the Content Engine, page 8-71
http dns-cache serial-lookup
http fast-response enable	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http l4-switch {enable | spoof-client-ip enable}
http max-ttl {days text textdays binary bindays | hours text texthours binary binhours | minutes text textminutes binary binminutes | seconds text textseconds binary binseconds}	Devices > Device Groups > Applications > Web > HTTP > HTTP Cache Freshness	Configuring HTTP Cache Freshness Settings, page 8-10
http min-ttl minutes
http monitor url {url {interval seconds | acceptable-delay seconds}}	Devices > Device Groups > Applications > Web > HTTP > HTTP Monitor URL	Monitoring Specified HTTP URLs, page 21-20
http object max-size kbytes	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http object url-validation enable
http persistent-connections [all | server-only | client-only]	Devices > Device Groups > Applications > Web > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings, page 8-19
http persistent-connections timeout seconds
http proxy incoming ports	Devices > Device Groups > Applications > Web > HTTP > HTTP Connections	Configuring HTTP Cache Settings, page 8-6
http proxy outgoing {connection-timeout microsecs | host {hostname | ipaddress} port [primary] | monitor seconds | origin-server | preserve-407}
http request-header host unmodified	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http reval-each-request all	Devices > Device Groups > Applications > Web > HTTP > HTTP Cache Freshness	Configuring HTTP Cache Freshness Settings, page 8-10
http reval-each-request none
http reval-each-request text
http serve-ims text percentage binary percentage
http smart-range enable	Devices > Device Groups > Applications > Web > HTTP > HTTP Caching	Configuring HTTP Cache Settings, page 8-6
http smart-range max-start offset max-interval interval
http strict-request-content-length-checking enable
http tcp-keepalive enable	Devices > Device Groups > Applications > Web > HTTP > Advanced HTTP Caching	Configuring Advanced HTTP Cache Settings, page 8-19
https proxy incoming ports	Devices > Device Groups > Applications > Web > HTTPS > HTTPS Proxy	Configuring HTTPS Proxy Settings, page 8-37
https proxy outgoing host {ipaddress | hostname} port
https destination-port {allow | deny}{range | all}
https tcp-rw-timeout seconds
https server name	Devices > Device Groups > Applications > Web > HTTPS > HTTPS Servers	Configuring HTTPS Servers, page 8-42
https server name {cert cert_name | certgroup {chain chainname | serverauth chainname} | enable | host {hostname | ipaddress} | key keyname password password | protocol-version {sslv2-only | sslv23-tlsv1 | sslv3-only | tlsv1-only} | serverauth {enable | ignore {cert-not-yet-valid | domain-name | expired-date | invalid-ca}} | session-cache {size size | timeout timeout}}	Devices > Device Groups > Applications > Web > HTTPS > Certificates	Configuring HTTPS Certificates, page 8-27
	Devices > Device Groups > Applications > Web > HTTPS > Certificate Groups	Configuring HTTPS Certificate Groups, page 8-31
	Devices > Device Groups > Applications > Web > HTTPS > Keys	Configuring HTTPS Keys, page 8-34
icap append-x-headers {x-client-ip | x-server-ip}	Devices > Device Groups > Request Processing > ICAP	Configuring ICAP Settings, page 16-4
icap apply {all | rules-template}
icap bypass streaming-media
icap logging {format standard | enable}
icap rescan-cache ISTag-change
icap service service_id	Devices > Device Groups > Request Processing > ICAP Services	Configuring ICAP Services, page 16-7
ICAP service configuration mode (config-icap-service)# icap service service_id [enable | vector-point {reqmod-precache | reqmod-postcache | respmod-precache} | error-handling {bypass | return-error} | load-balancing {round-robin | client-ip-hash | server-ip-hash | weighted-load}]
ICAP service configuration mode (config-icap-service)# icap service server server server_url {max-connections num | weight num}	Devices > Device Groups > Request Processing > ICAP Services	Configuring an ICAP Server for ICAP Service, page 16-10
icp client add-remote-server {hostname | ipaddress} {parent | sibling} icp-port icpport http-port httpport [restrict domainnames]	Devices > Device Groups > Applications > Web > HTTP > ICP > Remote Servers	ICP Remote Server Settings, page 8-84
icp client enable	Devices > Device Groups > Applications > Web > HTTP > ICP > Client	ICP Client Settings, page 8-80
icp client exclude domainnames
icp client max-fail retries
icp client max-wait timeout
icp client modify-remote-server {hostname | ipaddress} {http-port port | icp-port port | parent | restrict domainnames | sibling}	Devices > Device Groups > Applications > Web > HTTP > ICP > ICP Remote Servers	ICP Remote Server Settings, page 8-84
icp server enable	Devices > Device Groups > Applications > Web > HTTP > ICP > Server	ICP Server Settings, page 8-83
icp server http-port httpport
icp server port icpport
icp server remote-client {hostname | ipaddress} {fetch | no-fetch}	Devices > Device Groups > Applications > Web > HTTP > ICP > Remote Clients	ICP Remote Client Settings, page 8-82
inetd enable ftp	Devices > Device Groups > Applications > Web > FTP > Inetd FTP	Enabling Inetd FTP Service, page 8-61
inetd enable tftp	Devices > Device Groups > Applications > Web > TFTP > TFTP General Settings	Configuring TFTP General Settings, page 8-65
inetd enable rcp	Devices > Device Groups > General Settings > Network > Inetd RCP	Enabling RCP Services on the Content Engine, page 20-8
interface {FastEthernet | GigabitEthernet} slot/port cdp enable	Devices > Devices1 > General Settings > Network > Network Interfaces	Modifying Fast Ethernet or Gigabit Ethernet Interface Settings, page 14-7
interface {FastEthernet | GigabitEthernet} slot/port shutdown
interface {FastEthernet | GigabitEthernet} slot/port autosense
interface {FastEthernet | GigabitEthernet} slot/port bandwidth {10 | 100 | 1000}
interface {FastEthernet | GigabitEthernet} slot/port [full-duplex | half-duplex]
interface {FastEthernet | GigabitEthernet} slot/port mtu size
interface {FastEthernet | GigabitEthernet} slot/port ip address ipaddress netmask [secondary]
interface {FastEthernet | GigabitEthernet} slot/port standby groupnum ip ipaddress netmask	Devices > Devices1> General Settings > Network > Network Interfaces	Configuring a Standby Interface Using the Content Distribution Manager GUI, page 14-3
interface {FastEthernet | GigabitEthernet} slot/port standby groupnum errors num
interface {FastEthernet | GigabitEthernet} slot/port standby groupnum priority priority	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring the Interface Priority Setting, page 14-4
interface {FastEthernet | GigabitEthernet} slot/port ip address dhcp {client-id id hostname name | hostname name client-id id}		Configuring Interfaces for DHCP, page 14-13
interface FibreChannel slot/port [mode {autosense | direct-attached | switched} | speed {1 | 2 | autosense}]		Configuring the Fibre Channel Interface, page 14-9
interface PortChannel {1 | 2} [ip address ipaddress netmask | shutdown]	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring EtherChannel, page 14-11
interface {FastEthernet | GigabitEthernet} slot/port ip access-group {accesslistnumber | accesslistname} {in | out}	Devices > Devices1 > General Settings > Network > Network Interfaces	Applying an IP ACL to an Interface, page 17-13
ip access-list {standard | extended} {acl_name | acl_num} Includes other configuration commands for standard and extended IP ACLs.	Devices > Devices1 > General Settings > Network > IP ACL	Creating or Modifying an IP ACL, page 17-2
Extended ACL configuration mode (config-ext-nacl)# [insert line_num] {deny | permit}{gre | ip | proto_num} {source_ip [wildcard] | host source_ip | any} {dest_ip [wildcard] | host dest_ip | any} [insert line_num] {deny | permit} tcp {source_ip [wildcard] | host source_ip | any} [operator port [port]] {dest_ip [wildcard] | host dest_ip | any} [operator port [port]] [established] [insert line_num] {deny | permit} udp {source_ip [wildcard] | host source_ip | any} [operator port [port]] {dest_ip [wildcard] | host dest_ip | any} [operator port [port]] [insert line_num] {deny | permit} icmp {source_ip [wildcard] | host source_ip | any} {dest_ip [wildcard] | host dest_ip | any} [icmp_type [code] | icmp_msg] delete line_num | list [start_line_num [end_line_num]] | move oldline_num newline_num | exit	Devices > Devices1 > General Settings > Network > IP ACL	Adding Conditions to an IP ACL, page 17-3
Standard ACL configuration mode (config-std-nacl)# [insert line_num] {deny | permit} {source_ip [wildcard] | host source_ip | any} delete line_num | list [start_line_num [end_line_num]] | move oldline_num newline_num | exit	Devices > Devices1 > General Settings > Network > IP ACL	Adding Conditions to an IP ACL, page 17-3
ip default-gateway ipaddress	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring a Standby Interface Using the Content Distribution Manager GUI, page 14-3
		Modifying Fast Ethernet or Gigabit Ethernet Interface Settings, page 14-7
ip domain-name name1 name2 name3	Devices > Device Groups > General Settings > Network > DNS	Configuring the DNS Server for HTTP Proxy Caching, page 8-78
ip name-server ipaddress
ip dscp {client {cache-hit {match-server | set-dscp dscp-packets | set-tos tos-packets} | cache-miss {match-server | set-dscp dscp-packets | set-tos tos-packets}} | server {match-client | set-dscp dscp-packets | set-tos tos-packets}}	Devices > Device Groups > General Settings > Network > IP General Settings	Configuring IP Differentiated Services, page 10-9
ip path-mtu-discovery enable
ip route dest_addrs netmask gateway_addrs	Devices > Devices1 > General Settings > Network > IP Routes	Configuring Static IP Routes, page 14-15
kernel kdb	Devices > Device Groups > General Settings > Troubleshooting > Kernel Debugger	Enabling Kernel Debugger, page 21-23
ldap server administrative-dn name	Devices > Device Groups > General Settings > Authentication > LDAP Server	Configuring LDAP Server Settings, page 15-17
ldap server administrative-passwd passwd
ldap server allow-mode
ldap server base baseword
ldap server enable	Devices > Device Groups > General Settings > Authentication > Authentication Scheme	Setting the Authentication Scheme for Request Authentication, page 15-36
ldap server filter filterword	Devices > Device Groups > General Settings > Authentication > LDAP Server	Configuring LDAP Server Settings, page 15-17
ldap server group active-directory enable
ldap server group {organizationUnit enable | custom name enable | static {group-attribute name | member-attribute {member | uniquemember | custom-member name} | enable | nested {enable | level number}}}	Devices > Device Groups > General Settings > Authentication > LDAP Server	Configuring LDAP Server Settings, page 15-17
ldap server host {hostipaddress | hostname} [primary | secondary]
ldap server password-expiry {enable | redirect-url url}
ldap server policy-redirect {enable | redirect-url url | attribute name | version-number number}
ldap server policy-redirect append-request-url
ldap server port port_num
ldap server retransmit retries
ldap server timeout seconds
ldap server userid-attribute useridword
ldap server version ver_num
line console carrier-detect	Devices > Device Groups > General Settings > Login Access Control > Console Carrier Detect	Configuring Line Console Carrier Detection, page 20-6
logging host {ipaddress | hostname}	Devices > Device Groups > General Settings > Notification and Tracking > System Logs	Configuring System Event Logging Using the Content Distribution Manager GUI, page 21-5
logging host priority {alert | critical | debug | emergency | error | information | notice | warning}
logging disk enable
logging disk filename filename
logging disk recycle size
logging disk priority {alert | critical | debug | emergency | error | information | notice | warning}
logging console enable
logging console priority {alert | critical | debug | emergency | error | information | notice | warning}
logging facility {auth | daemon | kernel | local0 | local1 | local2 | local3 | local4 | local5 | local6 | local7 | mail | news | syslog | user | uucp}
multicast license-key key	Devices > Device Groups > Prepositioning > Multicast Distribution License	Enabling Content Engines for Multicasting, page 5-33
multicast accept-license-agreement multicast enable
multicast evaluate
network-filesystem server {samba | cifs} {enable | authentication-mode {public | ce-user | cifs-user | password-server} | max-connections num}	Devices > Device Groups > General Settings > File Sharing > CIFS Server	Configuring CIFS Server Settings, page 13-17
network-filesystem server {samba | cifs} {share-web-site site_name [share-auth-content | protect-auth-content]}	Devices > Device Groups > General Settings > File Sharing > CIFS Server Access Control	Configuring CIFS Server Website Access Control Settings, page 13-19
network-filesystem client {cifs {hostname | ipaddress} directory {cdnfs | mediafs} reserved-disk-space space username name password password [domain domain] | nfs {hostname | ipaddress} directory {cdnfs | mediafs} reserved-disk-space space}	Devices > Devices1 > General Settings > Storage > NAS	See "Attaching and Detaching NAS Shares Using the Content Distribution Manager GUI" in the Cisco ACNS Software Update and Maintenance Guide, Release 5.x.
ntlm server ad-group-search {enable | enum-user | gc-server | groupname-attribute | ldap-referral | ldap-search-port | membership-attribute | user-objectclass | username-attribute}	Devices > Device Groups > General Settings > Authentication > NTLM Server	Configuring NTLM Server Settings, page 15-23
ntlm server ad-group-search mem-cache {enable | size kilobytes | max-ttl minutes}	Devices > Device Groups > General Settings > Authentication > NTLM Server	Configuring the NTLM Server LDAP Memory Cache Settings, page 15-28
ntlm allow-domain {enable | domain domainname}	Devices > Device Groups > General Settings > Authentication > NTLM Allow Domain	Configuring NTLM Allowed Domains for HTTP Request Authentication, page 15-31
ntlm server enable	Devices > Device Groups > General Settings > Authentication > Authentication Scheme	Setting the Authentication Scheme for Request Authentication, page 15-36
ntlm server host {hostname | ipaddress}	Devices > Device Groups > General Settings > Authentication > NTLM Server	Configuring NTLM Server Settings, page 15-23
ntlm server domain name
ntp server {hostname | ipaddress}	Devices > Device Groups > General Settings > Network > NTP	Configuring NTP Settings, page 20-11
offline-operation enable	Devices > Device Groups > Applications > Web > Offline Operations	Enabling Offline Operation of Network Devices, page 20-27
port-channel load-balance {dst-ip | dst-mac | round-robin}	Devices > Devices1 > General Settings > Network > Network Interfaces	Configuring EtherChannel, page 14-11
proxy-auto-config enable	Devices > Device Groups > Applications > Web > Client Proxy Autoconfiguration	Configuring Client Proxy Autoconfiguration Settings, page 4-39
proxy-protocols outgoing-proxy exclude {enable | list word}	Devices > Device Groups > Applications > Web > Outgoing Proxy Exclusions	Configuring HTTP and HTTPS Outgoing Proxy Exclusion Settings, page 8-48
proxy-protocols transparent {default-server | original-proxy | reset}
qos camiant-cdn-am-service config-file filename or URL	Devices > Device Groups > Request Processing > PCMM > QoS Policy Service	Setting QoS Policy Server Settings for Content Engines, page 16-62
qos camiant-cdn-am-service enable
radius-server key key	Devices > Device Groups > General Settings > Authentication > RADIUS Server	Configuring RADIUS Server Settings, page 15-32
radius-server timeout seconds
radius-server enable	Devices > Device Groups > General Settings > Authentication > Authentication Scheme	Setting the Authentication Scheme for Request Authentication, page 15-36
radius-server host {hostname | ipaddress} {auth-port port}	Devices > Device Groups > General Settings > Authentication > RADIUS Server	Configuring RADIUS Server Settings, page 15-32
radius-server retransmit retries
radius-server redirect enable
radius-server redirect message reply location url
rtsp advanced max-initial-setup-delay seconds	Devices > Device Groups > Applications > Streaming > RTSP Gateway	Configuring the RTSP Gateway, page 9-8
rtsp advanced max-request-rate number
rtsp proxy media-real enable	Devices > Device Groups > Applications > Streaming > Real Networks > Real Proxy License	Enabling RealProxy, page 9-10
rtsp proxy media-real evaluate
rtsp proxy media-real license-key key
rtsp proxy media-real accept-license-agreement
rtsp server real-subscriber license-key key	Devices > Device Groups > Applications > Streaming > Real Networks > Real Subscriber License	Enabling RealSubscriber, page 9-12
rtsp server real-subscriber accept-license-agreement
rtsp server real-subscriber evaluate
rtsp server real-subscriber enable
rtsp l4-switch enable	Devices > Device Groups > Applications > Streaming > RTSP Gateway	Configuring the RTSP Gateway, page 9-8
rtsp port incoming port_num
rtsp ip-address ipaddress
rtsp server cisco-streaming-engine enable	Devices > Device Groups > Applications > Streaming > Cisco Streaming Engine	Enabling the Cisco Streaming Engine, page 9-14
rtsp server cisco-streaming-engine broadcast port-list list_num port_num	Services > Video > Programs > Live Streaming (indirect support)	Configuring Live Stream Settings for a Cisco Streaming Engine Live Program, page 7-20
rtsp server cisco-streaming-engine broadcast id id source {source-rtsp rtsp_url | source-udp url srce_ip_addr recv_ip_addr recv_port_list_num} {track-count 1-4} destination {destination-pull | destination-udp ttl dest_ip_addr dest_list_num}
rule enable	Devices > Device Groups > Request Processing > Enable Rules	Enabling Rule Settings, page 16-14
rule action rule action allow pattern-list list_num [protocol {all | http | https | rtsp}] rule action append-username-header pattern-list list_num [protocol {all | http | https}] rule action block pattern-list list_num [protocol {all | http | https | rtsp}] rule action cache-non-cacheable ttl {day days pattern-list list_num [protocol {all | http | https}] | hours hours pattern-list list_num [protocol {all | http | https}] | minutes minutes pattern-list list_num [protocol {all | http | https}] | seconds seconds pattern-list list_num [protocol {all | http | https}]}	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
rule action cache-only pattern-list list_num [protocol {all | http | https}] rule action dscp client cache-hit {match-server pattern-list list_num [protocol {all | http | https}] | set-dscp dscpvalue | set-tos tosvalue} rule action dscp client cache-miss {match-server pattern-list list_num [protocol {all | http | https}] | set-dscp dscpvalue | set-tos tosvalue} rule action dscp server {match-client pattern-list list_num [protocol {all | http | https}] | set-dscp dscpvalue | set-tos tosvalue}	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
rule action freshness-factor exp_time pattern-list list_num [protocol {all | http | https}] rule action generate-url-signature [include-client-src-ip] key-id-owner owner_num key-id-number id_num pattern-list list_num [protocol {all | http}] rule action insert-no-cache pattern-list list_num [protocol {all | http | https}] rule action no-auth pattern-list list_num [protocol {all | http | https | rtsp}] rule action no-cache pattern-list list_num [protocol {all | http | https}] rule action no-persistent-connection {all | client | server} pattern-list list_num [protocol {all | http | https}]	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
rule action no-proxy pattern-list list_num [protocol {all | http | https}] rule action redirect url pattern-list list_num [protocol {all | http | https | rtsp}] rule action redirect-url-for-cdn pattern-list list_num [protocol {all | http | https | rtsp}] rule action refresh pattern-list list_num [protocol {all | http | https}] rule action reset pattern-list list_num [protocol {all | http | https | rtsp}] rule action rewrite pattern-list list_num [protocol {all | http | https | rtsp}]	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
rule action use-dns-server {hostname | ipaddress} pattern-list list_num [protocol {all | http | https}] rule action use-icap-service service_name pattern-list list_num [protocol {all | http | https}] rule action use-proxy {hostname | ipaddress} port pattern-list list_num [protocol {all | http | https}] rule action use-proxy {hostname | ipaddress} port [failover] pattern-list list_num [protocol {all | http | https}] rule action use-server {hostname | ipaddress} port pattern-list list_num [protocol {all | http | https}] rule action use-xforward-clt-ip pattern-list list_num [protocol {all | http | https}] rule action validate-url-signature error-redirect-url url pattern-list list_num [protocol {all | http | rtsp}]	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
rule pattern-list list_num domain dn_regexp rule pattern-list list_num dst-ip d_ipaddress d_subnet rule pattern-list list_num dst-port port rule pattern-list list_num groupname name rule pattern-list list_num groupname-regex group_name_regexp rule pattern-list list_num group-type {and | or} rule pattern-list list_num header-field {referer ref_regexp | request-line req_regexp | user-agent ua_regexp} rule pattern-list list_num header-field x-forwarded-for ipaddress rule pattern-list list_num header-field-sub {referer ref_regexp ref_sub | request-line req_regexp req_sub | user-agent ua_regexp ua_sub}	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
rule pattern-list list_num icap-attribute icap_attribute icap_value rule pattern-list list_num mime-type mt_regexp rule pattern-list list_num src-ip s_ipaddress s_subnet rule pattern-list list_num url-regex url_regexp rule pattern-list list_num url-regsub url_regexp url_sub rule pattern-list list_num username user_name	Devices > Device Groups > Request Processing > Service Rules	Configuring Service Rules, page 16-13
snmp-server contact line	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > General Settings	Configuring SNMP Traps, page 22-2
snmp-server enable traps [config | content-engine [disk-fail | disk-read | disk-write | overload-bypass | transaction-log] | entity | event | snmp [authentication | cold-start]]
snmp-server host {hostname | ipaddress} communitystring [v2c [retry num] [timeout seconds]] | [v3 {auth [retry num] [timeout seconds] | noauth [retry num] [timeout seconds] | priv [retry num] [timeout seconds]}]	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Host	Configuring SNMP Host Settings, page 22-10
snmp-server location line	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > General Settings	Configuring SNMP Traps, page 22-2
snmp-server user name group [auth {md5 password [priv password] | sha password [priv password]} | remote octetstring [auth {md5 password [priv password] | sha password [priv password]}]]	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > User	Configuring SNMP User Settings, page 22-8
snmp-server group name {v1 [notify name] [read name] [write name] | v2c [notify name] [read name] [write name] | v3 {auth [notify name] [read name] [write name] | noauth [notify name] [read name] [write name] | priv [notify name] [read name] [write name]}}	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Group	Configuring SNMP Group Settings, page 22-6
snmp-server community string [group groupname | rw]	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > Community	Configuring SNMP Community Settings, page 22-5
snmp-server view viewname MIBfamily {excluded | included}	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > View	Configuring SNMPv2 View Settings, page 22-9
snmp-server notify inform	Devices > Device Groups > General Settings > Notification and Tracking > SNMP > General Settings	Configuring SNMP Traps, page 22-2
snmp-server mib persist event
snmp-server access-list {std_acl_number | acl_name}	Devices > Devices1 > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application, page 17-12
sshd enable	Devices > Device Groups > General Settings > Network > SSH	Configuring Secure Shell Settings, page 20-2
sshd timeout seconds
sshd password-guesses num
ssh-key-generate key-length length
tacacs enable	Devices > Device Groups > General Settings > Authentication > TACACS+ Server	Configuring TACACS+ Server Settings, page 15-34
tacacs password ascii
tacacs timeout
tacacs retransmit
tacacs key
tacacs host {ipaddress | hostname} [primary]
tcp ecn enable	Devices > Device Groups > General Settings > Network > TCP	Configuring TCP Settings for Increased Cache Performance, page 10-1
tcp type-of-service enable
tcp cwnd-base segments
tcp increase-xmit-timer-value value
tcp init-ss-threshold value
tcp keepalive-probe-cnt count
tcp keepalive-probe-interval seconds
tcp keepalive-timeout seconds
tcp client-satellite
tcp client-mss max_seg_size
tcp client-receive-buffer kbytes
tcp client-rw-timeout seconds
tcp client-send-buffer kbytes
tcp server-satellite
tcp server-mss max_seg_size
tcp server-receive-buffer kbytes
tcp server-rw-timeout seconds
tcp server-send-buffer kbytes
telnet enable	Devices > Device Groups > General Settings > Network > Telnet	Enabling the Telnet Service on the Content Engine, page 20-1
tftp max-connections number	Devices > Device Groups > Applications > Web > TFTP > TFTP General Settings	Configuring TFTP General Settings, page 8-65
tftp-server dir directory	Devices > Device Groups > Applications > Web > TFTP > TFTP Directory	Configuring TFTP Directory Settings, page 8-69
tftp-server access-list {std_acl_number | acl_name}	Devices > Devices1 > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application, page 17-12
tftp-server gw proto ftp server {hostname | ipaddress} pri priority [name name passwd password] [path directory]	Devices > Device Groups > Applications > Web > TFTP > TFTP Proxy	Configuring TFTP Proxy Server Settings, page 8-66
tftp-server gw proto http server {hostname | ipaddress} [port port_num] pri priority [name name passwd password] [path directory]
transaction-logs archive max-file-size kbytes	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Enabling Transaction Logging with the Content Distribution Manager GUI, page 19-10
transaction-logs archive interval {seconds | every-week [on weekdays at hour:minute] | every-day {at hour:minute | every hours} | every-hour {at minute | every minutes}}
transaction-logs enable
transaction-logs export enable
transaction-logs export ftp-server {hostname | ipaddress} login password directory
transaction-logs export sftp-server {hostname | ipaddress} login password directory
transaction-logs export compress	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Enabling Transaction Logging with the Content Distribution Manager GUI, page 19-10
transaction-logs export interval {minutes | every-week [on weekdays at hour:minute] | every-day {at hour:minute | every hours} | every-hour {at minute | every minutes}}
transaction-logs file-marker
transaction-logs sanitize
transaction-logs log-windows-domain
transaction-logs format {squid | extended-squid | apache | custom string}
tvout signal {ntsc | pal}	Devices > Device Groups > Applications > Set Top Box > TV-out	Enabling the TV-Out Feature, page 7-31
tvout enable
url-filter http {bad-sites-deny | good-sites-allow} {enable | file filename}	Devices > Device Groups > Request Processing > URL Filter > HTTP > URL Filter Settings for HTTP Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 16-26
url-filter http websense allowmode enable		Configuring URL Filtering with Websense Enterprise Software, page 16-39
url-filter http websense enable
url-filter http websense server {ipaddress | hostname} port 1-65535 timeout seconds connections 1-250
url-filter http N2H2 allowmode enable		Configuring URL Filtering with the N2H2 Server, page 16-33
url-filter http N2H2 enable
url-filter http N2H2 server {ipaddress | hostname} port 1-65535 timeout
url-filter http smartfilter enable		Configuring URL Filtering with SmartFilter Software, page 16-55
url-filter http custom-message dirname	Devices > Device Groups > Request Processing > URL Filter	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 16-26 Configuring Custom Blocking Messages Using the CLI, page 16-31
url-filter wmt {bad-sites-deny | good-sites-allow} {enable | file filename}	Devices > Device Groups > Request Processing > URL Filter > WMT > URL Filter Settings for WMT Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 16-26
url-filter rtsp {bad-sites-deny | good-sites-allow} {enable | file filename}	Devices > Device Groups > Request Processing > URL Filter > RTSP > URL Filter Settings for RTSP Protocol
url-signature key-id-owner number key-id-number number key encryption_key	Devices > Device Groups > Request Processing > PCMM > URL Signature Key	Creating New URL Signature Keys for Content Engines, page 16-63
username name {cifs-password | password | privilege}	Devices > Device Groups > General Settings > Login Access Control > Users > Usernames	Creating User Accounts for Centrally Managed Devices, page 12-14
wccp access-list {std_acl_number | ext_acl_number | acl_name}	Devices > Devices1 > General Settings > Network > IP ACL Feature Usage	Associating an IP ACL with an Application, page 17-12
wccp custom-web-cache mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp custom-web-cache router-list-num num port port [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp dns mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp dns router-list-num num [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp flow-redirect enable	Devices > Device Groups > Request Routing > WCCP > General Settings	Configuring WCCP General Settings for the Content Engine, page 4-7
wccp ftp router-list-num num [assign-method-strict] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp ftp mask {[dst-ip-mask hex_num] [src-ip-mask hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp home-router ipaddress	Devices > Device Groups > Request Routing > WCCP > General Settings	Configuring WCCP General Settings for the Content Engine, page 4-7
wccp https-cache accept-all
wccp https-cache mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp https-cache router-list-num num port port [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp port-list list_num port_num	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Port Lists for the Content Engine, page 4-17
wccp rtsp mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp rtsp router-list-num num [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp reverse-proxy mask [dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp reverse-proxy router-list-num num [assign-method-strict] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp router-list list_num ipaddress	Devices > Device Groups > Request Routing > WCCP > Services	Creating WCCP Router Lists, page 4-14
wccp service-number service_num router-list-num num port-list-num port application {cache | streaming} [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [match-source-port] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp service-number service_num mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp shutdown max-wait seconds	Devices > Device Groups > Request Routing > WCCP > General Settings	Configuring WCCP General Settings for the Content Engine, page 4-7
wccp slow-start enable
wccp spoof-client-ip enable
wccp version {1 | 2}
wccp web-cache mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp web-cache router-list-num num [assign-method-strict] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp wmt mask {[dst-ip-mask hex_num] [dst-port-mask port_hex_num] [src-ip-mask hex_num] [src-port-mask port_hex_num]}	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Masks for the Content Engine, page 4-18
wccp wmt router-list-num num [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]	Devices > Device Groups > Request Routing > WCCP > Services	Configuring WCCP Service Settings for the Content Engine, page 4-10
wccp wmt-rtspu router-list-num num [assign-method-strict] [hash-destination-ip] [hash-destination-port] [hash-source-ip] [hash-source-port] [l2-redirect] [mask-assign] [password key] [weight percentage]
websense-server enable	Devices > Device Groups > Request Processing > URL Filter > HTTP > URL Filter Settings for HTTP Protocol	Configuring URL Filter Settings Using the Content Distribution Manager GUI, page 16-26
websense-server service {edir-agent {activate | edir-server administrative-passwd password} | eim activate | logon-agent activate | network-agent activate | policy {local activate | remote host hostname or IP address port portnum} | radius-agent activate | user activate}	Devices > Device Groups > Request Processing > Websense Server	Installing Websense Server Components for the Content Engine, page 16-50
wmt accelerate live-split enable	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt accelerate proxy-cache enable
wmt accelerate vod enable
wmt accept-license-agreement	Devices > Device Groups > Applications > Streaming > Windows Media > License	Enabling Windows Media Services, page 9-15
wmt advanced client idle-timeout seconds	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt advanced client max-packet-size bytes
wmt advanced server log-forwarding enable
wmt bandwidth incoming bypass-list {ipaddress | hostname} [ipaddress | hostname]	Devices > Devices1 > Applications > Streaming > Windows Media > Bypass List	Configuring the Windows Media Incoming Bandwidth Bypass List, page 9-47
wmt broadcast {alias-name name source url}	Devices > Device Groups > Applications > Streaming > Windows Media > Broadcast Alias	Configuring Multicast-In Unicast-Out, page 9-34 Configuring Unicast-In Unicast-Out, page 9-36
wmt cache enable	Devices > Device Groups > Applications > Streaming > Windows Media > License	Enabling Windows Media Services, page 9-15
wmt cache max-obj-size mbytes	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt disallowed-client-protocols {[http | rtspt | rtspu]}
wmt enable	Devices > Device Groups > Applications > Streaming > Windows Media > License	Enabling Windows Media Services, page 9-15
wmt evaluate
wmt extended transaction-log enable	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Using WMT Transaction Logging, page 19-15
wmt fast-cache enable	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt fast-cache max-delivery-rate num
wmt fast-start enable
wmt fast-start max-bandwidth kbits
wmt http allow extension file_extensions
wmt l4-switch enable
wmt license-key key	Devices > Device Groups > Applications > Streaming > Windows Media > License	Enabling Windows Media Services, page 9-15
wmt live-url-stripping enable	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt multicast {station-configuration name [{dest_addr dest_port media_source} [log {local | webserver webserver_url}] [nsc-reference {ref_URL}] [play-forever] [unicast-url url] | failover {alternate-source alt_src_url | retry-count number | retry-interval number} | schedule-start {minute hour day month | now}] | time-to-live ttl}	Devices > Device Groups > Applications > Streaming > Windows Media > Multicast Stations	Configuring Unicast-In Multicast-Out, page 9-28 Configuring Multicast-In Multicast-Out, page 9-31
wmt max-concurrent-sessions num	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt multicast schedule-start name minute hour day month	Devices > Device Groups > Applications > Streaming > Windows Media > Multicast Station Schedules	Configuring Windows Media Multicast Station Schedules, page 9-38
wmt multicast time-to-live ttl	Devices > Device Groups > Applications > Streaming > Windows Media > General Settings	Configuring Windows Media Proxy Settings for the Content Engine, page 9-18
wmt proxy outgoing http host {hostname | ipaddress} port
wmt proxy outgoing rtsp host {hostname | ipaddress} port
wmt transaction-logs format {extended {wms-41 | wms-90} | wms-41 | wms-90}	Devices > Device Groups > General Settings > Notification and Tracking > Transaction Logs	Using WMT Transaction Logging, page 19-15

1 This command can only be configured on individual devices; the Content Distribution Manager GUI does not support this command for device group configuration.

CLI Commands Not Supported in the Content Distribution Manager GUI

The following CLI commands are not supported in the Content Distribution Manager GUI:

•auto-register enable {FastEthernet number number | GigabitEthernet number number}

•bandwidth advanced config-file string

•cdm ip string

•cdm {role {primary | standby} | ui port number}

•cms enable

•cms rpc timeout {connection number transfer number | incoming-wait number}

•content-routing-api enable

•device mode

•exception {debug | coredump}

•multicast back-version-compatibility acns-5-0

•multicast sender-delay number

•multicast max-concurrent-jobs number minimal-target-rate number

•multicast priority-weight number

•multicast fixed-carousel enable

•pre-load

•rtsp server cisco-streaming-engine broadcast port-list number number

•rtsp server cisco-streaming-engine broadcast id string source {source-rtsp string | source-udp string ipaddress ipaddress number} {track-count number} destination {destination-pull | destination-udp number ipaddress number}