The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter describes how to configure Open Shortest Path First version 3(OSPFv3) for IPv6 networks.
This chapter includes the following sections:
•Licensing Requirements for OSPFv3
•Configuration Guidelines and Limitations
•Verifying OSPFv3 Configuration
OSPFv3 is an IETF link-state protocol (see "Overview" section). An OSPFv3 router sends a special message, called a hello packet, out each OSPF-enabled interface to discover other OSPFv3 neighbor routers. Once a neighbor is discovered, the two routers compare information in the Hello packet to determine if the routers have compatible configurations. The neighbor routers attempt to establish adjacency, which means that the routers synchronize their link-state databases to ensure that they have identical OSPFv3 routing information. Adjacent routers share link-state advertisements (LSAs) that include information about the operational state of each link, the cost of the link, and any other neighbor information. The routers then flood these received LSAs out every OSPF-enabled interface so that all OSPFv3 routers eventually have identical link-state databases. When all OSPFv3 routers have identical link-state databases, the network is converged (see the "Convergence" section). Each router then uses Dijkstra's Shortest Path First (SPF) algorithm to build its route table.
You can divide OSPFv3 networks into areas. Routers send most LSAs only within one area, which reduces the CPU and memory requirements for an OSPF-enabled router.
OSPFv3 supports IPv6. For information about OSPF for IPv4, see Chapter 6 "Configuring OSPFv2".
This section includes the following topics:
•Comparison of OSPFv3 and OSPFv2
•OSPFv3 and the IPv6 Unicast RIB
Much of the OSPFv3 protocol is the same as in OSPFv2. OSPFv3 is described in RFC 2740.
The key differences between the OSPFv3 and OSPFv2 protocols are as follows:
•OSPFv3 expands on OSPFv2 to provide support for IPv6 routing prefixes and the larger size of IPv6 addresses.
•LSAs in OSPFv3 are expressed as prefix and prefix length instead of address and mask.
•The router ID and area ID are 32-bit numbers with no relationship to IPv6 addresses.
•OSPFv3 uses link-local IPv6 addresses for neighbor discovery and other features.
•OSPFv3 can use the IPv6 authentication trailer (RFC 6506) or IPSec (RFC 4552) for authentication. However, neither of these options is supported on Cisco NX-OS.
•OSPFv3 redefines LSA types.
OSPFv3 routers periodically send Hello packets on every OSPF-enabled interface. The hello interval determines how frequently the router sends these Hello packets and is configured per interface. OSPFv3 uses Hello packets for the following tasks:
•Neighbor discovery
•Keepalives
•Bidirectional communications
•Designated router election (see the "Designated Routers" section)
The Hello packet contains information about the originating OSPFv3 interface and router, including the assigned OSPFv3 cost of the link, the hello interval, and optional capabilities of the originating router. An OSPFv3 interface that receives these Hello packets determines if the settings are compatible with the receiving interface settings.Compatible interfaces are considered neighbors and are added to the neighbor table (see the "Neighbors" section).
Hello packets also include a list of router IDs for the routers that the originating interface has communicated with. If the receiving interface sees its own router ID in this list, then bidirectional communication has been established between the two interfaces.
OSPFv3 uses Hello packets as a keepalive message to determine if a neighbor is still communicating. If a router does not receive a Hello packet by the configured dead interval (usually a multiple of the hello interval), then the neighbor is removed from the local neighbor table.
An OSPFv3 interface must have a compatible configuration with a remote interface before the two can be considered neighbors. The two OSPFv3 interfaces must match the following criteria:
•Hello interval
•Dead interval
•Area ID (see the "Areas" section)
•Optional capabilities
If there is a match, the information is entered into the neighbor table:
•Neighbor ID—The router ID of the neighbor router.
•Priority—Priority of the neighbor router. The priority is used for designated router election (see the "Designated Routers" section).
•State—Indication of whether the neighbor has just been heard from, is in the process of setting up bidirectional communications, is sharing the link-state information, or has achieved full adjacency.
•Dead time—Indication of how long since the last Hello packet was received from this neighbor.
•Link-local IPv6 Address—The link-local IPv6 address of the neighbor.
•Designated Router—Indication of whether the neighbor has been declared the designated router or backup designated router (see the "Designated Routers" section).
•Local interface—The local interface that received the Hello packet for this neighbor.
When the first Hello packet is received from a new neighbor, the neighbor is entered into the neighbor table in the init state. Once bidirectional communication is established, the neighbor state becomes 2-way. ExStart and exchange states come next, as the two interfaces exchange their link-state database. Once this is all complete, the neighbor moves into the full state, signifying full adjacency. If the neighbor fails to send any Hello packets in the dead interval, then the neighbor is moved to the down state and is no longer considered adjacent.
Not all neighbors establish adjacency. Depending on the network type and designated router establishment, some neighbors become fully adjacent and share LSAs with all their neighbors, while other neighbors do not. For more information, see the "Designated Routers" section.
Adjacency is established using Database Description packets, Link State Request packets, and Link State Update packets in OSPFv3. The Database Description packet includes just the LSA headers from the link-state database of the neighbor (see the "Link-State Database" section). The local router compares these headers with its own link-state database and determines which LSAs are new or updated. The local router sends a Link State Request packet for each LSA that it needs new or updated information on. The neighbor responds with a Link State Update packet. This exchange continues until both routers have the same link-state information.
Networks with multiple routers present a unique situation for OSPFv3. If every router floods the network with LSAs, the same link-state information will be sent from multiple sources. Depending on the type of network, OSPFv3 might use a single router, the designated router (DR), to control the LSA floods and represent the network to the rest of the OSPFv3 area (see the "Areas" section). If the DR fails, OSPFv3 selects a backup designated router (BDR). If the DR fails, OSPFv3 uses the BDR.
Network types are as follows:
•Point-to-point—A network that exists only between two routers. All neighbors on a point-to-point network establish adjacency and there is no DR.
•Broadcast—A network with multiple routers that can communicate over a shared medium that allows broadcast traffic, such as Ethernet. OSPFv3 routers establish a DR and BDR that controls LSA flooding on the network. OSPFv3 uses the well-known IPv6 multicast addresses, FF02::5, and a MAC address of 0100.5300.0005 to communicate with neighbors.
The DR and BDR are selected based on the information in the Hello packet. When an interface sends a Hello packet, it sets the priority field and the DR and BDR field if it knows who the DR and BDR are. The routers follow an election procedure based on which routers declare themselves in the DR and BDR fields and the priority field in the Hello packet. As a final tie breaker, OSPFv3 chooses the highest router IDs as the DR and BDR.
All other routers establish adjacency with the DR and the BDR and use the IPv6 multicast address FF02::6 to send LSA updates to the DR and BDR. Figure 7-1 shows this adjacency relationship between all routers and the DR.
DRs are based on a router interface. A router might be the DR for one network and not for another network on a different interface.
Figure 7-1 DR in Multi-Access Network
Figure 7-2 OSPFv3 Areas
The ABR has a separate link-state database for each area which it connects to. The ABR sends Inter-Area Prefix (type 3) LSAs (see the "Route Summarization" section) from one connected area to the backbone area. The backbone area sends summarized information about one area to another area. In Figure 7-2, Area 0 sends summarized information about Area 5 to Area 3.
OSPFv3 defines one other router type: the autonomous system boundary router (ASBR). This router connects an OSPFv3 area to another autonomous system. An autonomous system is a network controlled by a single technical administration entity. OSPFv3 can redistribute its routing information into another autonomous system or receive redistributed routes from another autonomous system. For more information, see "Advanced Features" section.
OSPFv3 uses link-state advertisements (LSAs) to build its routing table.
This section includes the following topics:
•Flooding and LSA Group Pacing
Table 7-1 shows the LSA types supported by Cisco NX-OS.
|
|
|
---|---|---|
1 |
Router LSA |
LSA sent by every router. This LSA includes state and cost of all links. Does not include prefix information. Router LSAs trigger an SPF recalculation. Router LSAs are flooded to the local OSPFv3 area. |
2 |
Network LSA |
LSA sent by the DR. Lists all routers in the multi-access network. This LSA does not include prefix information. Network LSAs trigger an SPF recalculation. See the "Designated Routers" section. |
3 |
Inter-Area Prefix LSA |
LSA sent by the area border router to an external area for each destination in local area. This LSA includes the link cost from area the border router to the local destination. See the "Areas" section. |
4 |
Inter-Area Router LSA |
LSA sent by the area border router to an external area. This LSA advertises the link cost to the ASBR only. See the "Areas" section. |
5 |
AS External LSA |
LSA generated by the ASBR. This LSA includes the link cost to an external autonomous system destination. AS External LSAs are flooded throughout the autonomous system. See the "Areas" section. |
7 |
Type-7 LSA |
LSA generated by the ASBR within an NSSA. This LSA includes the link cost to an external autonomous system destination. Type-7 LSAs are flooded only within the local NSSA. See the "Areas" section. |
8 |
Link LSA |
LSA sent by every router, using a link-local flooding scope (see the "Flooding and LSA Group Pacing" section. This LSA includes the link-local address and IPv6 prefixes for this link. |
9 |
Intra-Area Prefix LSA |
LSA sent by every router. This LSA includes any prefix or link state changes. Intra-Area Prefix LSAs are flooded to the local OSPFv3 area. This LSA does not trigger an SPF recalculation. |
11 |
Grace LSAs |
LSA sent by a restarting router, using a link-local flooding scope. This LSA is used for a graceful restart of OSPFv3. See the "High Availability and Graceful Restart" section. |
Each OSPFv3 interface is assigned a link cost. The cost is an arbitrary number. By default, Cisco NX-OS assigns a cost that is the configured reference bandwidth divided by the interface bandwidth. By default, the reference bandwidth is 40 Gb/s. The link cost is carried in the LSA updates for each link.
OSPFv3 floods LSA updates to different sections of the network, depending on the LSA type. OSPFv3 uses the following flooding scopes:
•Link-local—LSA is flooded only on the local link, and no further. Used for Link LSAs and Grace LSAs.
•Area-local—LSA is flooded throughout a single OSPF area only. Used for Router LSAs, Network LSAs, Inter-Area-Prefix LSAs, Inter-Area-Router LSAs, and Intra-Area-Prefix LSAs.
•AS scope—LSA is flooded throughout the routing domain. Used for AS External LSAs.
LSA flooding guarantees that all routers in the network have identical routing information. LSA flooding depends on the OSPFv3 area configuration (see the "Areas" section). The LSAs are flooded based on the link-state refresh time (every 30 minutes by default). Each LSA has its own link-state refresh time.
You can control the flooding rate of LSA updates in your network by using the LSA group pacing feature. LSA group pacing can reduce high CPU or buffer utilization. This feature groups LSAs with similar link-state refresh times to allow OSPFv3 to pack multiple LSAs into an OSPFv3 Update message.
By default, LSAs with link-state refresh times within four minutes of each other are grouped together. You should lower this value for large link-state databases or raise it for smaller databases to optimize the OSPFv3 load on your network.
Each router maintains a link-state database for the OSPFv3 network. This database contains all the collected LSAs, and includes information on all the routes through the network. OSPFv3 uses this information to calculate the bast path to each destination and populates the routing table with these best paths.
LSAs are removed from the link-state database if no LSA update has been received within a set interval, called the MaxAge. Routers flood a repeat of the LSA every 30 minutes to prevent accurate link-state information from being aged out. Cisco NX-OS supports the LSA grouping feature to prevent all LSAs from refreshing at the same time. For more information, see the "Flooding and LSA Group Pacing" section.
OSPFv3 multi-area adjacency allows you to configure a link on the primary interface that is in more than one area. This link becomes the preferred intra-area link in those areas. Multi-area adjacency establishes a point-to-point unnumbered link in an OSPFv3 area that provides a topological path for that area. The primary adjacency uses the link to advertise an unnumbered point-to-point link in the RouterLSA for the corresponding area when the neighbor state is full.
The multi-area interface exists as a logical construct over an existing primary interface for OSPF; however, the neighbor state on the primary interface is independent of the multi-area interface. The multi-area interface establishes a neighbor relationship with the corresponding multi-area interface on the neighboring router. See the "Configuring Multi-Area Adjacency" section for more information.
OSPFv3 runs the Dijkstra shortest path first algorithm on the link-state database. This algorithm selects the best path to each destination based on the sum of all the link costs for each link in the path. The resultant shortest path for each destination is then put in the OSPFv3 route table. When the OSPFv3 network is converged, this route table feeds into the IPv6 unicast RIB. OSPFv3 communicates with the IPv6 unicast RIB to do the following:
•Add or remove routes
•Handle route redistribution from other protocols
•Provide convergence updates to remove stale OSPFv3 routes and for stub router advertisements (see the "Multiple OSPFv3 Instances" section)
OSPFv3 also runs a modified Dijkstra algorithm for fast recalculation for Inter-Area Prefix, Inter-Area Router, AS-External, Type-7, and Intra-Area Prefix (type 3, 4, 5, 7, 8) LSA changes.
Cisco NX-OS supports multiple address families, such as unicast IPv6 and multicast IPv6. OSPFv3 features that are specific to an address family are as follows:
•Default routes
•Route summarization
•Route redistribution
•Filter lists for border routers
•SPF optimization
Use the address-family ipv6 unicast command to enter the IPv6 unicast address family configuration mode when configuring these features.
Cisco NX-OS supports a number of advanced OSPFv3 features that enhance the usability and scalability of OSPFv3 in the network.
This section includes the following topics:
•High Availability and Graceful Restart
You can limit the amount of external routing information that floods an area by making it a stub area. A stub area is an area that does not allow AS External (type 5) LSAs (see the "Link-State Advertisement" section). These LSAs are usually flooded throughout the local autonomous system to propagate external route information. Stub areas have the following requirements:
•All routers in the stub area are stub routers. See the "Stub Routing" section.
•No ASBR routers exist in the stub area.
•You cannot configure virtual links in the stub area.
Figure 7-3 shows an example an OSPFv3 autonomous system where all routers in area 0.0.0.10 have to go through the ABR to reach external autonomous systems. area 0.0.0.10 can be configured as a stub area.
Figure 7-3 Stub Area
Stub areas use a default route for all traffic that needs to go through the backbone area to the external autonomous system. The default route is an Inter-Area-Prefix LSA with prefix length set to 0 for IPv6.
A Not-So-Stubby Area (NSSA) is similar to the stub area, except that an NSSA allows you to import autonomous system external routes within an NSSA using redistribution. The NSSA ASBR redistributes these routes and generates Type-7 LSAs that it floods throughout the NSSA. You can optionally configure the ABR that connects the NSSA to other areas to translate this Type-7 LSA to AS External (type 5) LSAs. The ABR then floods these AS External LSAs throughout the OSPFv3 autonomous system. Summarization and filtering are supported during the translation. See the "Link-State Advertisement" section for details on Type-7 LSAs.
You can, for example, use NSSA to simplify administration if you are connecting a central site using OSPFv3 to a remote site that is using a different routing protocol. Before NSSA, the connection between the corporate site border router and a remote router could not be run as an OSPFv3 stub area because routes for the remote site could not be redistributed into a stub area. You needed to maintain two routing protocols. With NSSA, you can extend OSPFv3 to cover the remote connection by defining the area between the corporate router and remote router as an NSSA (see the "Configuring NSSA" section).
The backbone Area 0 cannot be an NSSA.
Virtual links allow you to connect an OSPFv3 area ABR to a backbone area ABR when a direct physical connection is not available. Figure 7-4 shows a virtual link that connects Area 3 to the backbone area through Area 5.
Figure 7-4 Virtual Links
You can also use virtual links to temporarily recover from a partitioned area, which occurs when a link within the area fails, isolating part of the area from reaching the designated ABR to the backbone area.
OSPFv3 can learn routes from other routing protocols by using route redistribution. See the "Route Redistribution" section. You configure OSPFv3 to assign a link cost for these redistributed routes or a default link cost for all redistributed routes.
Route redistribution uses route maps to control which external routes are redistributed. You must configure a route map with the redistribution to control which routes are passed into OSPFv2. A route map allows you to filter routes based on attributes such as the destination, origination protocol, route type, route tag, and so on. You can use route maps to modify parameters in the AS External (type 5) and NSSA External (type 7) LSAs before these external routes are advertised in the local OSPFv3 autonomous system. See Chapter 16 "Configuring Route Policy Manager," for details on configuring route maps.
Because OSPFv3 shares all learned routes with every OSPF-enabled router, you might want to use route summarization to reduce the number of unique routes that are flooded to every OSPF-enabled router. Route summarization simplifies route tables by replacing more-specific addresses with an address that represents all the specific addresses. For example, you can replace 2010:11:22:0:1000::1 and 2010:11:22:0:2000:679:1 with one summary address, 2010:11:22::/32.
Typically, you would summarize at the boundaries of area border routers (ABRs). Although you could configure summarization between any two areas, it is better to summarize in the direction of the backbone so that the backbone receives all the aggregate addresses and injects them, already summarized, into other areas. The two types of summarization are as follows:
•Inter-area route summarization
•External route summarization
You configure inter-area route summarization on ABRs, summarizing routes between areas in the autonomous system. To take advantage of summarization, you should assign network numbers in areas in a contiguous way to be able to lump these addresses into one range.
External route summarization is specific to external routes that are injected into OSPFv3 using route redistribution. You should make sure that external ranges that are being summarized are contiguous. Summarizing overlapping ranges from two different routers could cause packets to be sent to the wrong destination. Configure external route summarization on ASBRs that are redistributing routes into OSPF
When you configure a summary address, Cisco NX-OS automatically configures a discard route for the summary address to prevent routing black holes and route loops.
Cisco NX-OS provides a multilevel high-availability architecture. OSPFv3 supports stateful restart, which is also referred to as non-stop routing (NSR). If OSPFv3 experiences problems, it attempts to restart from its previous run-time state. The neighbors do not register any neighbor event in this case. If the first restart is not successful and another problem occurs, OSPFv3 attempts a graceful restart.
A graceful restart, or non-stop forwarding (NSF), allows OSPFv3 to remain in the data forwarding path through a process restart. When OSPFv3 needs to perform a graceful restart, it sends a link-local Grace (type 11) LSA. This restarting OSPFv3 platform is called NSF capable.
The Grace LSA includes a grace period, which is a specified time that the neighbor OSPFv3 interfaces hold onto the LSAs from the restarting OSPFv3 interface. (Typically, OSPFv3 tears down the adjacency and discards all LSAs from a down or restarting OSPFv3 interface.) The participating neighbors, which are called NSF helpers, keep all LSAs that originate from the restarting OSPFv3 interface as if the interface was still adjacent.
When the restarting OSPFv3 interface is operational again, it rediscovers its neighbors, establishes adjacency, and starts sending its LSA updates again. At this point, the NSF helpers recognize that the graceful restart has finished.
Stateful restart is used in the following scenarios:
•First recovery attempt after the process experiences problems
•ISSU
•User-initiated switchover using the system switchover command
Graceful restart is used in the following scenarios:
•Second recovery attempt after the process experiences problems within a 4-minute interval
•Manual restart of the process using the restart ospfv3 command
•Active supervisor removal
•Active supervisor reload using the reload module active-sup command
Cisco NX-OS supports multiple instances of the OSPFv3 protocol. By default, every instance uses the same system router ID. You must manually configure the router ID for each instance if the instances are in the same OSPFv3 autonomous system.
The OSPFv3 header includes an instance ID field to identify that OSPFv3 packet for a particular OSPFv3 instance. You can assign the OSPFv3 instance. The interface drops all OSPFv3 packets that do not have a matching OSPFv3 instance ID in the packet header.
Cisco NX-OS allows only one OSPFv3 instance on an interface.
Cisco NX-OS optimizes the SPF algorithm in the following ways:
•Partial SPF for Network (type 2) LSAs, Inter-Area Prefix (type 3) LSAs, and AS External (type 5) LSAs—When there is a change on any of these LSAs, Cisco NX-OS performs a faster partial calculation rather than running the whole SPF calculation.
•SPF timers—You can configure different timers for controlling SPF calculations. These timers include exponential backoff for subsequent SPF calculations. The exponential backoff limits the CPU load of multiple SPF calculations.
OSPFv3 supports Virtual Routing and Forwarding instances (VRFs). VRFs exist within virtual device contexts (VDCs). By default, Cisco NX-OS places you in the default VDC and default VRF unless you specifically configure another VDC and VRF. Each OSPFv3 instance can support multiple VRFs, up to the system limit. For more information, see the Cisco Nexus 7000 Series NX-OS Virtual Device Context Configuration Guide, Release 4.xand see Chapter 14 "Configuring Layer 3 Virtualization."
The following table shows the licensing requirements for this feature:
OSPFv3 has the following prerequisites:
•You must be familiar with routing fundamentals to configure OSPFv3.
•You must be logged on to the switch.
•You have configured at least one interface for IPv6 that is capable of communicating with a remote OSPFv3 neighbor.
•You have installed the Enterprise Services license.
•You have completed the OSPFv3 network strategy and planning for your network. For example, you must decide whether multiple areas are required.
•You have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
•You have installed the Advanced Services license and entered the desired VDC (see the Cisco Nexus 7000 Series NX-OS Virtual Device Context Configuration Guide, Release 4.x) if you are configuring VDCs.
•You are familiar with IPv6 addressing and basic configuration. See Chapter 3 "Configuring IPv6" for information on IPv6 routing and addressing.
OSPFv3 has the following configuration guidelines and limitations:
•You can have up to four instances of OSPFv3 in a VDC.
•Cisco NX-OS displays areas in dotted decimal notation regardless of whether you enter the area in decimal or dotted decimal notation.
•If you configure OSPFv3 in a vPC environment, use the following timer commands in router configuration mode on the core switch to ensure fast OSPF convergence when a vPC peer-link is shut down:
switch (config-router)# timers throttle spf 1 50 50
switch (config-router)# timers lsa-arrival 10
Note If you are familiar with the Cisco IOS CLI, be aware that the Cisco NX-OS commands for this feature might differ from the Cisco IOS commands that you would use.
Configure OSPFv3 after you have designed your OSPFv3 network.
This section includes the following topics:
•Configuring Networks in OSPFv3
You must enable the OSPFv3 feature before you can configure OSPFv3.
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. feature ospfv3
3. show feature
4. copy running-config startup-config
Use the no feature ospfv3 command to disable the OSPFv3 feature and remove all associated configuration.
|
|
---|---|
no feature ospfv3
Example: switch(config)# no feature ospfv3 |
Disables the OSPFv3 feature and removes all associated configuration. |
The first step in configuring OSPFv3 is to create an instance or OSPFv3 instance. You assign a unique instance tag for this OSPFv3 instance. The instance tag can be any string. For each OSPFv3 instance, you can also configure the following optional parameters:
•Router ID—Configures the router ID for this OSPFv3 instance. If you do not use this parameter, the router ID selection algorithm is used. See the "Router IDs" section.
•Administrative distance—Rates the trustworthiness of a routing information source. See the "Administrative Distance" section.
•Log adjacency changes—Creates a system message whenever an OSPFv3 neighbor changes its state.
•Maximum paths—Sets the maximum number of equal paths that OSPFv3 installs in the route table for a particular destination. Use this parameter for load balancing between multiple paths.
•Reference bandwidth—Controls the calculated OSPFv3 cost metric for a network. The calculated cost is the reference bandwidth divided by the interface bandwidth. You can override the calculated cost by assigning a link cost when a network is added to the OSPFv3 instance. See the "Configuring Networks in OSPFv3" section.
For more information about OSPFv3 instance parameters, see the"Configuring Advanced OSPFv3" section.
Ensure that you have enabled the OSPFv3 feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that the OSPFv3 instance tag that you plan on using is not already in use on this router.
Use the show ospfv3 instance-tag command to verify that the instance tag is not in use.
OSPFv3 must be able to obtain a router identifier (for example, a configured loopback address) or you must configure the router ID option.
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. router-id ip-address
4. show ipv6 ospfv3 instance-tag
5. copy running-config startup-config
Use the no router ospfv3 command to remove the OSPFv3 instance and all associated configuration.
|
|
---|---|
no router ospfv3 instance-tag
Example: switch(config)# no router ospfv3 201 |
Deletes the OSPFv3 instance and all associated configuration. |
Note This command does not remove OSPF configuration in interface mode. You must manually remove any OSPFv3 commands configured in interface mode.
You can configure the following optional parameters for OSPFv3 in router configuration mode:
|
|
---|---|
log-adjacency-changes [detail]
Example: switch(config-router)# log-adjacency-changes |
Generates a system message whenever a neighbor changes state. |
Use the address-family ipv6 unicast command to configure the following optional parameters for OSPFv3 in address family configuration mode:
The following example shows how to create an OSPFv3 instance:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# copy running-config startup-config
You can configure a network to OSPFv3 by associating it through the interface that the router uses to connect to that network (see the "Neighbors" section). You can add all networks to the default backbone area (Area 0), or you can create new areas using any decimal number or an IP address.
Note All areas must connect to the backbone area either directly or through a virtual link.
Note OSPFv3 is not enabled on an interface until you configure a valid IPv6 address for that interface.
Ensure that you have enabled the OSPFv3 feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. interface interface-type slot/port
3. ipv6 address ipv6-prefix/length
4. ipv6 router ospfv3 instance-tag area area-id [secondaries none]
5. show ipv6 ospfv3 instance-tag interface interface-type slot/port
6. copy running-config startup-config
You can configure the following optional parameters for OSPFv3 in interface configuration mode:
|
|
---|---|
ospfv3 cost number
Example: switch(config-if)# ospfv3 cost 25 |
Configures the OSPFv3 cost metric for this interface. The default is to calculate cost metric, based on reference bandwidth and interface bandwidth. The range is from 1 to 65535. |
ospfv3 dead-interval seconds
Example: switch(config-if)# ospfv3 dead-interval 50 |
Configures the OSPFv3 dead interval, in seconds. The range is from 1 to 65535. The default is four times the hello interval, in seconds. |
ospfv3 hello-interval seconds
Example: switch(config-if)# ospfv3 hello-interval 25 |
Configures the OSPFv3 hello interval, in seconds. The range is from 1 to 65535. The default is 10 seconds. |
ospfv3 instance instance
Example: switch(config-if)# ospfv3 instance 25 |
Configures the OSPFv3 instance ID. The range is from 0 to 255. The default is 0. The instance ID is link-local in scope. |
ospfv3 mtu-ignore
Example: switch(config-if)# ospfv3 mtu-ignore |
Configures OSPFv3 to ignore any IP maximum transmission unit (MTU) mismatch with a neighbor. The default is to not establish adjacency if the neighbor MTU does not match the local interface MTU. |
ospfv3 network {broadcast | point-point}
Example: switch(config-if)# ospfv3 network broadcast |
Sets the OSPFv3 network type. |
ospfv3 passive-interface
Example: switch(config-if)# ospfv3 passive-interface |
Suppresses routing updates on the interface. |
ospfv3 priority number
Example: switch(config-if)# ospfv3 priority 25 |
Configures the OSPFv3 priority, used to determine the DR for an area. The range is from 0 to 255. The default is 1. See the "Designated Routers" section. |
ospfv3 shutdown
Example: switch(config-if)# ospfv3 shutdown |
Shuts down the OSPFv3 instance on this interface. |
The following example shows how to add a network area 0.0.0.10 in OSPFv3 instance 201:
switch# config t
switch(config)# interface ethernet 1/2
switch(config-if)# ipv6 address 2001:0DB8::1/48
switch(config-if)# ipv6 ospfv3 201 area 0.0.0.10
switch(config-if)# copy running-config startup-config
Configure OSPFv3 after you have designed your OSPFv3 network.
This section includes the following topics:
•Configuring Filter Lists for Border Routers
•Configuring a Totally Stubby Area
•Limiting the Number of Redistributed Routes
•Configuring Route Summarization
•Restarting an OSPFv3 Instance
•Configuring OSPFv3 with Virtualization
You can separate your OSPFv3 domain into a series of areas that contain related networks. All areas must connect to the backbone area through an area border router (ABR). OSPFv3 domains can connect to external domains as well, through an autonomous system border router (ASBR). See the "Areas" section.
ABRs have the following optional configuration parameters:
•Area range—Configures route summarization between areas. See the "Configuring Route Summarization" section.
•Filter list—Filters the Inter-Area Prefix (type 3) LSAs on an ABR that are allowed in from an external area.
ASBRs also support filter lists.
Create the route map that the filter list uses to filter ip prefixes in incoming or outgoing Inter-Area Prefix (type 3) LSAs. See Chapter 16 "Configuring Route Policy Manager."
Ensure that you have enabled the OSPFv3 feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. address-family ipv6 unicast
4. area area-id filter-list route-map map-name {in | out}
5. show ipv6 ospfv3 policy statistics area id filter-list {in | out}
6. copy running-config startup-config
The following example shows how to enable graceful restart if it has been disabled:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# address-family ipv6 unicast
switch(config-router-af)# area 0.0.0.10 filter-list route-map FilterLSAs in
switch(config-router-af)# copy running-config startup-config
You can configure a stub area for part of an OSPFv3 domain where external traffic is not necessary. Stub areas block AS External (type 5) LSAs, limiting unnecessary routing to and from selected networks. See the "Stub Area" section. You can optionally block all summary routes from going into the stub area.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that there are no virtual links or ASBRs in the proposed stub area.
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. area area-id stub
4. address-family ipv6 unicast
5. area area-id default-cost cost
6. copy running-config startup-config
The following example shows how to create a stub area that blocks all summary route updates:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 stub no-summary
switch(config-router)# copy running-config startup-config
You can create a totally stubby area and prevent all summary route updates from going into the stub area.
To create a totally stubby area, use the following command in router configuration mode:
|
|
---|---|
area area-id stub no-summary
Example: switch(config-router)# area 20 stub no-summary |
Creates this area as a totally stubby area. |
You can configure an NSSA for part of an OSPFv3 domain where limited external traffic is required. See the "Not-So-Stubby Area" section. You can optionally translate this external traffic to an AS External (type 5) LSA and flood the OSPFv3 domain with this routing information. An NSSA can be configured with the following optional parameters:
•No redistribution—Redistributed routes bypass the NSSA and are redistributed to other areas in the OSPFv3 autonomous system. Use this option when the NSSA ASBR is also an ABR.
•Default information originate—Generates a Type-7 LSA for a default route to the external autonomous system. Use this option on an NSSA ASBR if the ASBR contains the default route in the routing table. This option can be used on an NSSA ABR whether or not the ABR contains the default route in the routing table.
•Route map—Filters the external routes so that only those routes you want are flooded throughout the NSSA and other areas.
•Translate—Translates Type-7 LSAs to AS External (type 5) LSAs for areas outside the NSSA. Use this command on an NSSA ABR to flood the redistributed routes throughout the OSPFv3 autonomous system. You can optionally suppress the forwarding address in these AS External LSAs.
•No summary—Blocks all summary routes from flooding the NSSA. Use this option on the NSSA ABR.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that there are no virtual links in the proposed NSSA and that it is not the backbone area.
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. area area-id nssa [no-redistribution] [default-information-originate [route-map map-name]] [no-summary] [translate type7 {always | never} [suppress-fa]]
4. address-family ipv6 unicast
5. area area-id default-cost cost
6. copy running-config startup-config
The following example shows how to create an NSSA that blocks all summary route updates:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 nssa no-summary
switch(config-router)# copy running-config startup-config
The following example shows how to create an NSSA that generates a default route;
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 nssa default-info-originate
switch(config-router)# copy running-config startup-config
The following example shows how to create an NSSA that filters external routes and blocks all summary route updates:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 nssa route-map ExternalFilter no-summary
switch(config-router)# copy running-config startup-config
The following example shows how to create an NSSA that always translates Type-7 LSAs to AS External (type 5) LSAs:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 nssa translate type 7 always
switch(config-router)# copy running-config startup-config
The following example shows how to create an NSSA that blocks all summary route updates:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 nssa no-summary
switch(config-router)# copy running-config startup-config
You can add more than one area to an existing OSPFv3 interface. The additional logical interfaces support multi-area adjacency.
Ensure that you have enabled the OSPFv3 feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
Ensure that you have configured a primary area for the interface (see the "Configuring Networks in OSPFv3" section
1. config t
2. interface interface-type slot/port
3. ipv6 router ospfv3 instance-tag multi-area area-id
4. show ipv6 ospfv3 instance-tag interface interface-type slot/port
5. copy running-config startup-config
The following example shows how to add a second area to an OSPFv3 interface:
switch# config t
switch(config)# interface ethernet 1/2
switch(config-if)# ipv6 address 2001:0DB8::1/48
switch(config-if)# ipv6 ospfv3 201 area 0.0.0.10
switch(config-if)# ipv6 ospfv3 201 multi-area 20
switch(config-if)# copy running-config startup-config
A virtual link connects an isolated area to the backbone area through an intermediate area. See the "Virtual Links" section. You can configure the following optional parameters for a virtual link:
•Dead interval—Sets the time that a neighbor waits for a Hello packet before declaring the local router as dead and tearing down adjacencies.
•Hello interval—Sets the time between successive Hello packets.
•Retransmit interval—Sets the estimated time between successive LSAs.
•Transmit delay—Sets the estimated time to transmit an LSA to a neighbor.
Note You must configure the virtual link on both routers involved before the link becomes active.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. area area-id virtual-link router-id
4. show ipv6 ospfv3 virtual-link [brief]
5. copy running-config startup-config
You can configure the following optional commands in virtual link configuration mode:
The following example shows how to create a simple virtual link between two ABRs:
Configuration for ABR 1 (router ID 2001:0DB8::1) is as follows:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# area 0.0.0.10 virtual-link 2001:0DB8::10
switch(config-router)# copy running-config startup-config
Configuration for ABR 2 (router ID 2001:0DB8::10) is as follows:
switch# config t
switch(config)# router ospf 101
switch(config-router)# area 0.0.0.10 virtual-link 2001:0DB8::1
switch(config-router)# copy running-config startup-config
You can redistribute routes learned from other routing protocols into an OSPFv3 autonomous system through the ASBR.
You can configure the following optional parameters for route redistribution in OSPF:
•Default information originate—Generates an AS External (type 5) LSA for a default route to the external autonomous system.
Note Default information originate ignores match statements in the optional route map.
•Default metric—Sets all redistributed routes to the same cost metric.
Note If you redistribute static routes, Cisco NX-OS also redistributes the default static route.
Create the necessary route maps used for redistribution.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. address-family ipv6 unicast
4. redistribute {bgp id | direct | isis id | rip id | static} route-map map-name
5. default-information originate [always] [route-map map-name]
6. default-metric cost
7. copy running-config startup-config
The following example shows how to redistribute the Border Gateway Protocol (BGP) into OSPFv3:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# address-family ipv6 unicast
switch(config-router-af)# redistribute bgp route-map FilterExternalBGP
switch(config-router-af)# copy running-config startup-config
Route redistribution can add many routes to the OSPFv3 route table. You can configure a maximum limit to the number of routes accepted from external protocols. OSPFv3 provides the following options to configure redistributed route limits:
•Fixed limit—Log a message when OSPFv3 reaches the maximum the configured maximum. OSPFv3 does not accept any more redistributed routes. You can optionally configure a threshold percentage of the maximum where OSPFv3 will log a warning when that threshold is passed.
•Warning only—Log a warning only when OSPFv3 reaches the maximum. OSPFv3 continuse to accept redistributed routes.
•Widthdraw—Start the configured timeout period when OSPFv3 reaches the maximum. After the timeout period, OSPFv3 requests all redistributed routes if the current number of redistributed routes is less than the maximum limit. If the current number of redistributed routes is at the maximum limit, OSPFv3 widthdraws all redistributed routes. You must clear this condition before OSPFv3 accepts more redistributed routes.
You can optionally configure the timeout period.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. address-family ipv6 unicast
4. redistribute {bgp id | direct | isis id | rip id | static} route-map map-name
5. redistribute maximum-prefix max [threshold] [warning-only | withdraw [num-retries timeout]]
6. show running-config ospfv3
7. copy running-config startup-config
The following example shows how to limit the number of redistributed routes into OSPF:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# address-family ipv6 unicast
switch(config-router-af)# redistribute bgp route-map FilterExternalBGP
switch(config-router-af)# redistribute maximum-prefix 1000 75
You can configure route summarization for inter-area routes by configuring an address range that is summarized. You can also configure route summarization for external, redistributed routes by configuring a summary address for those routes on an ASBR. See the "Route Summarization" section.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. address-family ipv6 unicast
4. area area-id range ipv6-prefix/length [no-advertise]
or
5. summary-address ipv6-prefix/length [no-advertise] [tag tag]
6. show ipv6 ospfv3 summary-address
7. copy running-config startup-config
The following example shows how to create summary addresses between areas on an ABR:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# address-family ipv6 unicast
switch(config-router)# area 0.0.0.10 range 2001:0DB8::/48
switch(config-router)# copy running-config startup-config
The following example shows how to create summary addresses on an ASBR:
switch# config t
switch(config)# router ospf 201
switch(config-router)# address-family ipv6 unicast
switch(config-router)# summary-address 2001:0DB8::/48
switch(config-router)# copy running-config startup-config
OSPFv3 includes a number of timers that control the behavior of protocol messages and shortest path first (SPF) calculations. OSPFv3 includes the following optional timer parameters:
•LSA arrival time—Sets the minimum interval allowed between LSAs arriving from a neighbor. LSAs that arrive faster than this time are dropped.
•Pacing LSAs—Set the interval at which LSAs are collected into a group and refreshed, checksummed, or aged. This timer controls how frequently LSA updates occur and optimizes how many are sent in an LSA update message (see the "Flooding and LSA Group Pacing" section).
•Throttle LSAs—Set rate limits for generating LSAs. This timer controls how frequently an LSA is generated if no topology change occurs.
•Throttle SPF calculation—Controls how frequently the SPF calculation is run.
At the interface level, you can also control the following timers:
•Retransmit interval—Sets the estimated time between successive LSAs.
•Transmit delay—Sets the estimated time to transmit an LSA to a neighbor.
See the "Configuring Networks in OSPFv3" section for information on the hello interval and dead timer.
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. timers lsa-arrival msec
4. timers lsa-group-pacing seconds
5. timers throttle lsa e start-time hold-interval max-timel
6. address-family ipv6 unicast
7. timers throttle spf delay-time hold-time
8. interface type slot/port
9. ospfv3 retransmit-interval seconds
10. ospfv3 transmit-delay seconds
11. copy running-config startup-config
The following example shows how to control LSA flooding with the lsa-group-pacing option:
switch# config t
switch(config)# router ospf 201
switch(config-router)# timers lsa-group-pacing 300
switch(config-router)# copy running-config startup-config
Graceful restart is enabled by default. You can configure the following optional parameters for graceful restart in an OSPFv3 instance:
•Grace period—Configures how long neighbors should wait after a graceful restart has started before tearing down adjacencies.
•Helper mode disabled—Disables helper mode on the local OSPFv3 instance. OSPFv3 will not participate in the graceful restart of a neighbor.
•Planned graceful restart only—Configures OSPFv3 to support graceful restart only in the event of a planned restart.
Ensure that you have enabled the OSPFv3 feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that all neighbors are configured for graceful restart with matching optional parameters set.
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. router ospfv3 instance-tag
3. graceful-restart
4. graceful-restart grace-period seconds
5. graceful-restart helper-disable
6. graceful-restart planned-only
7. show ipv6 ospfv3 instance-tag
8. copy running-config startup-config
The following example shows how to enable graceful restart if it has been disabled, and set the grace period to 120 seconds:
switch# config t
switch(config)# router ospfv3 201
switch(config-router)# graceful-restart
switch(config-router)# graceful-restart grace-period 120
switch(config-router)# copy running-config startup-config
You can restart an OSPv3 instance. This clears all neighbors for the instance.
To restart an OSPFv3 instance and remove all associated neighbors, use the following command:
|
|
---|---|
restart ospfv3 instance-tag
Example: switch(config)# restart ospfv3 201 |
Restarts the OSPFv3 instance and removes all neighbors. |
You can configure multiple OSPFv3 instances in each VDC. You can also create multiple VRFs within each VDC and use the same or multiple OSPFv3 instances in each VRF. You assign an OSPFv3 interface to a VRF.
Note Configure all other parameters for an interface after you configure the VRF for an interface. Configuring a VRF for an interface deletes all the configuration for that interface.
Create the VDCs.
Ensure that you have enabled the OSPF feature (see the "Enabling the OSPFv3 Feature" section).
Ensure that you are in the correct VDC (or use the switchto vdc command).
1. config t
2. vrf context vrf_name
3. router ospfv3 instance-tag
4. vrf vrf-name
5. <optional parameters configured>
6. interface type slot/port
7. vrf member vrf-name
8. ipv6 address ipv6-prefix/length
9. ipv6 ospfv3 instance-tag area area-id
10. copy running-config startup-config
The following example shows how to create a VRF and add an interface to the VRF:
switch# config t
switch(config)# vrf context NewVRF
switch(config-vrf)# exit
switch(config)# router ospfv3 201
switch(config-router)# exit
switch(config)# interface ethernet 1/2
switch(config-if)# vrf member NewVRF
switch(config-if)# ipv6 address 2001:0DB8::1/48
switch(config-if)# ipv6 ospfv3 201 area 0
switch(config-if)# copy running-config startup-config
To verify OSPFv3 configuration, use one of the following commands:
To display OSPFv3 statistics, use the following commands:
The following example shows how to configure OSPFv3:
feature ospfv3
router ospfv3 201
router-id 290.0.2.1
interface ethernet 1/2
ipv6 address 2001:0DB8::1/48
ipv6 ospfv3 201 area 0.0.0.10
The following topics can give more information on OSPF:
•Chapter 6 "Configuring OSPFv2"
•Chapter 16 "Configuring Route Policy Manager"
Table 7-2 lists the default settings for OSPFv3 parameters.
For additional information related to implementing OSPF, see the following sections:
•MIBs
|
|
---|---|
•OSPF-MIB •OSPF-TRAP-MIB |
To locate and download MIBs, go to the following URL: http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml |
Table 7-3 lists the release history for this feature.
|
|
|
---|---|---|
OSPFv3 |
4.0(1) |
This feature was introduced. |