Cisco ONS 15454 Hardware Installation Guide
Installing the ONS 15454 M2 Shelf
Downloads: The complete bookPDF (PDF - 87.69MB) | Feedback

Table Of Contents

Installing the ONS 15454 M2 Shelf

4.1  ANSI Rack Installation

4.1.1  Mounting Brackets

4.1.2  Mounting a Single Node

4.2  ETSI Rack Installation

4.2.1  Mounting a Single Node

4.3  Wall Mounting the ONS 15454 M2 Shelf

4.4  Desktop Mounting the ONS 15454 M2 Shelf

4.5  Air Deflector

4.6  Air Plenum

4.7  Air Plenum Rack and Cabinet Compatibility

NTP-G343 Install the Air Plenum in ONS 15454 M2 Shelf

DLP-G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch Configuration

DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration

DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration

NTP-G266 Install the ONS 15454 M2 Shelf

DLP-G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration

DLP-G583 Mounting the 23-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration

DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration

DLP-G585 Mounting the Brackets on the ONS 1545 M2 Shelf for ETSI Rack Configuration

DLP-G586 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

DLP-G589 Mount the ONS 15454 M2 Shelf on a Rack (One Person)

DLP-G590 Mount the ONS 15454 M2 Shelf on the Wall

DLP-G591 Mount the ONS 15454 M2 Shelf on the Desktop

4.8  Front Door

NTP-G269 Install the Standard Door of the ONS 15454 M2 Shelf

NTP-G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf

DLP-G594 Open the Standard Door of the ONS 15454 M2 Shelf

DLP-G595 Remove the Standard Door of the ONS 15454 M2 Shelf

NTP-G343 Install the Deep-Front Panel of the ONS 15454 M2 Shelf

NTP-G331 Remove the Deep-Front Panel of the ONS 15454 M2 Shelf

4.9  Power Modules

4.9.1  AC Power Module

4.9.2  DC Power Module

NTP-G267 Install the Power Module in the ONS 15454 M2 Shelf

DLP-G592 Install the AC Power Module in the ONS 15454 M2 Shelf

DLP-G593 Install the DC Power Module in the ONS 15454 M2 Shelf

4.10  Fan-Tray Assembly

4.10.1  Fan Speed

4.10.2  Fan Failure

NTP-G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf

4.11  Power and Ground Description

4.11.1  ANSI Power and Ground

4.11.2  ETSI Power and Ground

NTP-G271 Install the Power and Ground to the ONS 15454 M2 Shelf

DLP-G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf

DLP-G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only)

DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only)

DLP-G599 Turn On and Verify AC Office Power on the ONS 15454 M2 Shelf

DLP-G600 Turn On and Verify DC Office Power on the ONS 15454 M2 Shelf

NTP-G291 Attach Wires to Timing, LAN, and Craft Pin Connections in ONS 15454 M2

DLP-G292 Install Timing Wires in ONS 15454 M2 - ANSI

DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI

DLP-G294 Install LAN Wires in ONS 15454 M2

NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card

DLP-G604 Install the TNC, TNCE, TSC, or TSCE Card

DLP-G605 Provision PPM and Port for the TNC and TNCE Cards

DLP-G606 Configure UDC and VoIP for the TNC and TNCE Cards

NTP-G275 Perform the ONS 15454 M2 Shelf Installation Acceptance Test

DLP-G601 Inspect the ONS 15454 M2 Shelf Installation and Connections

DLP-G602 Measure DC Voltage on the ONS 15454 M2 Shelf

4.12  Filler Card

4.13  Air Filter

4.14  Shelf Voltage and Temperature


Installing the ONS 15454 M2 Shelf


This chapter explains how to install the ONS 15454 M2 shelf.

4.1  ANSI Rack Installation

The ONS 15454 M2 shelf is mounted on a 19-inch (482.6-mm) or 23-inch (584.2-mm) equipment rack. Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M2 shelf as shown in Figure 1-1. If the shelf is mounted in the front position, then it projects 1.7 inches (43.18 mm) from the front of the rack. If the shelf is mounted in the middle position, then it projects 5.1 inches (129.54 mm) from the front of the rack. The shelf mounts in both Electronic Industries Alliance (EIA) standard and Telcordia-standard racks. The shelf is a total of 17.2 inches (431.8 mm) wide with no mounting ears attached. Ring runs are not provided by Cisco and might hinder side-by-side installation of shelves where space is limited.

The ONS 15454 M2 shelf measures 3.5 inches (88.9 mm) high, 19 or 23 inches (482.6 or 584.2 mm) wide (depending on which way the mounting ears are attached), and 11.1 inches (304.8 mm) deep.

Figure 4-1 shows the dimensions of the ONS 15454 M2 shelf in a 19-inch configuration with brackets mounted in the front position.

Figure 4-1 Cisco ONS 15454 M2 Shelf Dimensions for a 19-inch ANSI Rack Configuration

4.1.1  Mounting Brackets


Caution Use only the fastening hardware provided with the ONS 15454 M2 shelf to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Caution When mounting the ONS 15454 M2 shelf in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 shipping kit, or remove the coating from the threads to ensure electrical continuity.

The mounting brackets (19-inch or 23-inch) are used to mount the shelf on a 19-inch (482.6 mm) rack or a 23-inch (584.2 mm) rack.

4.1.2  Mounting a Single Node

Mounting the ONS 15454 M2 shelf on a rack requires a minimum of 3.5 inches (88.9 mm) of vertical rack space. To ensure the mounting is secure, use two to three #12-24 mounting screws for each side of the shelf. For an ANSI rack, the brackets can be mounted in the front or middle position. The shelf should be empty for easier lifting. For information on the ONS 15454 M2 shelf weight, refer to the "Dimensions" section.

The ONS 15454 M2 shelves can be mounted above each other without any space between the shelves. This method of mounting does not restrict the air flow because the air vents are on either sides of the ONS 15454 M2 shelves.

4.2  ETSI Rack Installation

The ONS 15454 M2 shelf is mounted on a 600 x 600-mm (23.6 x 23.6-inch) or 600 x 300-mm (23.6 x 11.8-inch) ETSI standard equipment rack. In an ETSI rack, the shelf can be mounted only in the front position. The shelf projects 1.7 inches from the front of the rack. The shelf is a total of 17.2 inches (431.8 mm) wide with no mounting ears attached. Cisco does not provide ring runs, which might hinder side-by-side installation of shelves where space is limited.

The ONS 15454 M2 shelf measures 88.9 mm (3.5 inches) high, 535 mm (21.06 inches) wide, and 11.1 inches (304.8 mm) deep.

Figure 4-2 provides the dimensions of the ONS 15454 M2 shelf installed on a 600 x 600-mm (23.6 x 23.6-inch) ETSI standard equipment rack.


Caution When mounting a shelf in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Figure 4-2 ONS 15454 M2 Shelf Dimensions for an ETSI Rack Configuration

4.2.1  Mounting a Single Node

The ONS 15454 M2 requires 3.5 inches (88.9 mm) minimum of vertical rack space. To ensure the mounting is secure, use two to three M6 mounting screws for each side of the shelf.

In an ETSI rack, the brackets can be mounted only in the front position.

The ONS 15454 M2 shelves can be mounted above each other without any space between the shelves. This method of mounting does not restrict the air flow because the air vents are on either sides of the ONS 15454 M2 shelves.

4.3  Wall Mounting the ONS 15454 M2 Shelf

The ONS 15454 M2 shelf can be mounted on the wall using the wall mount brackets. The type of screws used to mount the brackets on the wall depends on the wall-type and are not provided by Cisco.

After the ONS 15454 M2 shelf is mounted on the wall, a fire protective tray is installed on the wall mount bracket to support the shelf.

4.4  Desktop Mounting the ONS 15454 M2 Shelf

The ONS 15454 M2 shelf can be mounted on the desktop for easy access.

4.5  Air Deflector

An air deflector is a sheet-metal part that is mounted on the ONS 15454 M2 shelf to orient the air flow in a specific direction.

The air deflectors can be mounted in different positions to control the air flow:

Front to Front— Only ETSI rack

Front to Back— For ANSI and ETSI racks

Front to Top— Only ETSI rack

In an ANSI rack, the air deflectors are mounted only on the 23-inch rack configuration.

4.6  Air Plenum

Air plenum orients the air flow in the front-to-back direction inside the equipment to be compliant with GR-63 issue 4 requirement.

The air plenum kit has one horizontal and two vertical air plenums. The air that flows from the front top inlet are channelized to the right vertical plenum, inside the equipment, and then to the exhaust air channel towards the left vertical air plenum. The air flow is deflected by 90 degrees and exited out in the rear end.

Figure 4-3 shows the air flow inside the cabinet.

Figure 4-3 Air flow within the air plenum in the cabinet

Figure 4-4 and Figure 4-5 shows the dimensions of the air plenum relative to the cabinet or rack.

Figure 4-4 Dimension of Cisco ONS 15454 M2 chassis relative to the air plenum

Figure 4-5

Dimension on CIsco ONS 15454 M2 relative to the air plenum

4.7  Air Plenum Rack and Cabinet Compatibility

The table shows the compatibility of air plenum with the ANSI and ETSI racks and cabinets. The chassis can be installed with brackets in front position only.

Table 4-1

Rack / Cabinet
Front-to-back air flow

ANSI 19-inch rack

Supported 1

ANSI 19-inch cabinet

Supported1

ANSI 23-inch rack

Supported

ANSI 23-inch cabinet

Supported

ETSI cabinet

Supported1


Air plenum compatibility with racks and cabinets

1 A minimum opening of 20.600 inches is required to install the vertical air plenum behind the front rails.

Figure 4-6 Minimum rear opening for ANSI 19-inch and ETSI configuration

NTP-G343 Install the Air Plenum in ONS 15454 M2 Shelf

Purpose

This procedure installs the air plenum to orient the air flow from front-to- back direction in the ONS 15454 M2 shelf.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Screws

ANSI: #12-24 x 0.50 pan-head Phillips screws

ETSI: M6.0 x 20 pan-head Phillips screws

Wing head screws (4)

Adapter plates

One air plenum kit (horizontal and vertical air plenums)

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1074

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units. Statement 246

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39

Note For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC.



Note Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.



Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning The air plenum is installed on a rack or a cabinet using thread-forming screws that remove any paint or non-conductive coatings inside the hole threads, and establish a metal-to-metal contact. Also, clean both surfaces outside the screw points that come in contact, so that they are free of paint and other nonconductive coating. Apply an appropriate antioxidant compound to the surfaces.

Step 1 Depending on the rack or cabinet, complete the necessary task:

G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch Configuration

G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration

G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration

Stop. You have completed this procedure.

DLP-G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch Configuration

Purpose

This task installs the air plenum for the ONS 15454 M2 shelf in ANSI 19-inch cabinet or rack configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Screws: #12-24 x 0.50 pan-head Phillips screws (4)

Wing head screws (4)

One air plenum kit (horizontal and vertical air plenum)

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Note In the 19-inch rack and cabinet, the air plenum can be mounted only if the minimum opening is 20.600 inches to install the vertical air plenums behind the front rails.



Step 1 Place the horizontal air plenum above the shelf slot in the ANSI 19-inch cabinet or rack.

Step 2 Insert the wing head screws provided with the kit, and tighten to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-7 Installing the horizonatl air plenum in the ANSI 19-inch configuration

Step 3 Install the vertical air plenum to the left of the horizontal air plenum:

a. Insert the vertical plenum in the free space between the horizontal plenum and cabinet.

b. Install t he wing head screws fom the internal side of the horizontal plenum as shown in Figure 4-8.

c. Tighten the screws to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-8 Installing the left vertical air plenum

Step 4 Install the vertical air plenum to the right of the horizontal air plenum. Follow step 3a to 3c.

Figure 4-9 Installing the right vertical air plenum

Step 5 Install the 19-inch standard brackets on both sides of the chassis in the front position. See G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration.

Step 6 Install the ONS 15454 M2 empty chassis below the horizontal plenum.

Figure 4-10 Installing the ONS 15454 M2 chassis below the horizontal air plenum

Step 7 Return to your originating procedure (NTP).


DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration

Purpose

This task installs the air plenum for the ONS 15454 M2 shelf in the ANSI 23-inch cabinet or rack configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Screws: #12-24 x 3/4 pan-head Phillips mounting screws (4)

Wing head screws (4)

Adapter plates

One air plenum kit (horizontal and vertical air plenum)

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Note The airplenums for ANSI 23-inch configuration can be pre-assembled outside the cabinet and then installed inside the cabinet.



Step 1 Install the ANSI 23-inch adapter plates on the horizontal air plenum.

Step 2 Align the screws to fix the adapter plates to the shelf. Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-11 Installing the adapter plates on the horizontal air plenum

Step 3 Place the horizontal air plenum above the shelf slot in the ANSI 23-inch cabinet or rack.

Step 4 Insert the wing head screws provided with the kit, and tighten to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-12 Installing the horizonatl air plenum in the ANSI 23-inch configuration

Step 5 Install the vertical air plenum to the left of the horizontal air plenum:

a. Insert the vertical air plenum in the free space between the horizontal air plenum and cabinet.

b. Install the wing head screws from the internal side of the horizontal plenum as shown in Figure 4-13.

c. Tighten the screws to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-13 Installing the left vertical air plenum

Step 6 Install the vertical plenum to the right of the horizontal air plenum. Follow step 5a to 5c.

Figure 4-14 Installing the right vertical air plenum

Step 7 Install ANSI 19-inch standard brackets on both sides of the chassis in front position. See G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration.

Step 8 Install the ONS 15454 M2 empty chassis below the horizontal plenum.

Figure 4-15 Installing the ONS 15454 M2 chassis below the horizontal air plenum

Step 9 Return to your originating procedure (NTP).


DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration

Purpose

This task installs the air plenum for the ONS 15454 M2 shelf in the ETSI configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Screws: M6.0 x 20 pan-head Phillips screws (4)

Wing head screws (4)

Adapter plates

One air plenum kit (horizontal and vertical air plenum)

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Install the ETSI adapter plates on the horizontal air plenum.

Step 2 Align the screws to fix the adapter plates to the horizontal air plenum. Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m) as shown in Figure 4-16.

Figure 4-16 Installing the adapter plates on the horizontal air plenum

Step 3 Place the horizontal plenum above the chassis slot in the ETSI cabinet.

Step 4 Insert the wing head screws provided with the kit, and tighten to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-17 Installing the horizonatl air plenum in the ETSI configuration

Step 5 Install the vertical air plenum to the left of the horizontal air plenum:

a. Insert the vertical plenum in the free space between the horizontal plenum and cabinet.

b. Install the wing head screws from the internal side of the horizontal plenum as shown in Figure 4-18.

c. Tighten the screws to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-18 Installing the left vertical air plenum

Step 6 Install the vertical air plenum to the right of the horizontal air plenum. Follow step 5a to 5c.

Figure 4-19 Installing the right vertical air plenum

Step 7 Install the ANSI 19-inch mounting brackets on both sides of the chassis in front position. See G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration.

Step 8 Install the ONS 15454 M2 empty chassis below the horizontal plenum.

Figure 4-20 Installing the ONS 15454 M2 chassis below the horizontal air plenum

Step 9 Return to your originating procedure (NTP).


NTP-G266 Install the ONS 15454 M2 Shelf

Purpose

This procedure installs the shelf.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

ETSI only:

Two M6 x 20 pan-head Phillips mounting screws

ANSI only:

Two #12-24 x 3/4 pan-head Phillips mounting screws

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over. Statement 1048

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security. Statement 1072

Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 10A-20A, 100-240 VAC~. Statement 1005

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 131°F (55°C). Statement 1047

Warning Take care when connecting units to the supply circuit so that wiring is not overloaded. Statement 1018


Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006



Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least:
1 inch (25.4 mm) Statement 1076

Note Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M2 shelf as shown in Figure 1-1.



Note During installation, do not use the door to handle the chassis.



Note Remove the door from the ONS 15454 M2 shelf and reinstall it after installation of all the other modules is complete.



Step 1 Complete the necessary task as applicable:

"DLP-G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration" task.

"DLP-G583 Mounting the 23-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration" task.

"DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration" task.

"DLP-G585 Mounting the Brackets on the ONS 1545 M2 Shelf for ETSI Rack Configuration" task.

"DLP-G586 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration" task.

"DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration" task.

"DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration" task.

Step 2 Complete the necessary mounting task as applicable:

G589 Mount the ONS 15454 M2 Shelf on a Rack (One Person).

G590 Mount the ONS 15454 M2 Shelf on the Wall

G591 Mount the ONS 15454 M2 Shelf on the Desktop

Step 3 Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Step 4 Continue with "NTP-G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf" procedure.

Stop. You have completed this procedure.


DLP-G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration

Purpose

This task installs the 19-inch mounting brackets to the ONS 15454 M2 shelf for ANSI rack configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Caution When mounting the ONS 15454 M2 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 ship kit, or remove the coating from the threads to ensure electrical continuity.


Note The mounting brackets can be installed in the front or the middle position of the chassis.



Step 1 Place the wider side of the 19-inch mounting bracket flush against the shelf (see Figure 4-21). The narrow side of the mounting bracket should be towards the front of the shelf.

Step 2 Align the mounting bracket screw holes against the shelf screw holes.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4 Repeat steps 1 through 3 for the mounting bracket on the opposite side.

Figure 4-21 Mounting the Brackets on the ONS  15454 M2 shelf for a 19-inch (482.6-mm) ANSI Configuration

Step 5 Return to your originating procedure (NTP).


DLP-G583 Mounting the 23-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration

Purpose

This task installs the 23-inch mounting brackets on the ONS 15454 M2 shelf for ANSI rack configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Caution When mounting the ONS 15454 M2 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 ship kit, or remove the coating from the threads to ensure electrical continuity.


Note The mounting brackets can be installed in the front or the middle position of the chassis.



Step 1 Place the narrow side of the 23-inch mounting bracket flush against the shelf (see Figure 4-22). The wider side of the mounting bracket should be towards the front of the shelf.

Step 2 Align the mounting bracket screw holes against the shelf screw holes.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4 Repeat steps 1 through 3 for mounting the bracket on the opposite side.

Figure 4-22 Mounting the Brackets on the ONS 15454 M2 shelf for a 23-inch (584.2-mm) ANSI Configuration

Step 5 Return to your originating procedure (NTP).


DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration

Purpose

This task mounts the 23-inch brackets with air deflectors (front-to-back) on the ONS 15454 M2 shelf for ANSI rack configuration.

Note In an ANSI rack, the air deflectors can be mounted only in the 23-inch rack configuration and in the front position of the chassis.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Step 1 Place the right front air deflector flush against the right side of the chassis as shown in Diagram 1 of Figure 4-23.

Step 2 Align the screw holes on the right front air deflector with the screw holes on right side of the chassis.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 2 of Figure 4-23.

Step 4 Place the left back air deflector flush against the chassis as shown in Diagram 1 of Figure 4-23.


Note If the 100G-LC-C, 10x10G-LC, or CFP-LC cards are to be installed in the ONS 15454 M2 shelf, do not mount the left back deflector (exhaust air deflector). Use the standard brackets directly to mount the ONS 15454 M2 shelf.


Step 5 Align the screw holes on the left back air deflector with the screw holes on the chassis.

Step 6 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 2 of Figure 4-23.

Step 7 Place the air deflector covers on the front and rear ends of the chassis as shown in Diagram 3 of Figure 4-23.

Step 8 Align the screw holes on the air deflector covers with the screw holes on the chassis.

Step 9 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 4 of Figure 4-23.

Step 10 Place the 23-inch mounting bracket flush in the front position (see Diagram 1 of Figure 4-24) or in the middle position (see Diagram 3 of Figure 4-24) against the right side of the chassis.

Step 11 Align the screw holes on the 23-inch mounting bracket with the screw holes on the right side of the chassis.

Step 12 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 13 Place the 23-inch mounting bracket flush in the front position (see Diagram 1 of Figure 4-24) or in the middle position (see Diagram 3 of Figure 4-24) against the left side of the chassis.

Step 14 Align the screw holes on the 23-inch mounting bracket with the screw holes on the left side of the chassis.

Step 15 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-23 Mounting the Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration

Figure 4-24 Mounting the Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration

Step 16 Return to your originating procedure (NTP).


DLP-G585 Mounting the Brackets on the ONS 1545 M2 Shelf for ETSI Rack Configuration

Purpose

This task installs the mounting brackets on the ONS 15454 M2 shelf for ETSI rack configuration.

Note In an ETSI rack, the air deflectors can be mounted only in the front position of the chassis.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Caution When mounting the ONS 15454 M2 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 ship kit, or remove the coating from the threads to ensure electrical continuity.


Step 1 Place the mounting bracket flush against the shelf as shown in Figure 4-25.

Step 2 Align the mounting bracket screw holes against the shelf screw holes.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4 Repeat steps 1 through 3 for the mounting bracket on the opposite side.

Figure 4-25 Mounting the Brackets on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Step 5 Return to your originating procedure (NTP).


DLP-G586 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Purpose

This task mounts the air deflectors (front-to-front) on the ONS 15454 M2 shelf for ETSI rack configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Note The air deflectors can be installed only in the front position of the chassis.



Step 1 Place the right front air deflector flush against the right side of the chassis as shown in Diagram 1 of Figure 4-26.

Step 2 Align the screw holes on the right front air deflector with the screw holes on right side of the chassis.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 1 of Figure 4-26.

Step 4 Place the left front air deflector flush against the chassis as shown in Diagram 1 of Figure 4-26.


Note If the 100G-LC-C, 10x10G-LC, or CFP-LC cards are to be installed in the ONS 15454 M2 shelf, do not mount the left front deflector (exhaust air deflector). Use the standard brackets directly to mount the ONS 15454 M2 shelf.


Step 5 Align the screw holes on the left back air deflector with the screw holes on the chassis.

Step 6 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 1 of Figure 4-26.

Step 7 Place the air deflector covers on the rear ends of the chassis as shown in Diagram 2 of Figure 4-26.

Step 8 Align the screw holes on the air deflector covers with the screw holes on the chassis.

Step 9 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 10 Place the mounting bracket flush in the front position (see Diagram 3 of Figure 4-26) against the right side of the chassis.

Step 11 Align the screw holes on the mounting bracket with the screw holes on the right side of the chassis.

Step 12 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 13 Place the other mounting bracket flush in the front position (see Diagram 3 of Figure 4-26) against the left side of the chassis.

Step 14 Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 15 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-26 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Step 16 Return to your originating procedure (NTP).


DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Purpose

This task installs the bracket with air deflectors (front-to-back) on the ONS 15454 M2 shelf for ETSI rack configuration.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Note The air deflectors can be installed only in the front position of the chassis.



Step 1 Place the right front air deflector flush against the right side of the chassis as shown in Diagram 1 of Figure 4-27.

Step 2 Align the screw holes on the right front air deflector with the screw holes on right side of the chassis.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 2 of Figure 4-27.

Step 4 Place the left back air deflector flush against the chassis as shown in Diagram 1 of Figure 4-27.


Note If the 100G-LC-C, 10x10G-LC, or CFP-LC cards are to be installed in the ONS 15454 M2 shelf, do not mount the left back deflector (exhaust air deflector). Use the standard brackets directly to mount the ONS 15454 M2 shelf.


Step 5 Align the screw holes on the left back air deflector with the screw holes on the chassis.

Step 6 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 2 of Figure 4-27.

Step 7 Place the air deflector covers on the front and rear ends of the chassis as shown in Diagram 3 of Figure 4-27.

Step 8 Align the screw holes on the air deflector covers with the screw holes on the chassis.

Step 9 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 4 of Figure 4-27.

Step 10 Place the mounting bracket flush in the front position (see Diagram 1 of Figure 4-28) or in the middle position (see Diagram 3 of Figure 4-28) against the right side of the chassis.

Step 11 Align the screw holes on the 23-inch mounting bracket with the screw holes on the right side of the chassis.

Step 12 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 13 Place the mounting bracket flush in the front position (see Diagram 1 of Figure 4-28) or in the middle position (see Diagram 3 of Figure 4-28) against the left side of the chassis.

Step 14 Align the screw holes on the 23-inch mounting bracket with the screw holes on the left side of the chassis.

Step 15 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Figure 4-27 Mounting the Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Figure 4-28 Mounting the Brackets with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Step 16 Return to your originating procedure (NTP).


DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Purpose

This task installs the bracket with air deflectors (front-to-top configuration) on the ONS 15454 M2 shelf.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.


Note The air deflectors can be installed only in the front position of the chassis.



Step 1 Place the right front air deflector flush against the right side of the chassis (see Diagram 1 of Figure 4-29).

Step 2 Align the screw holes on the right front air deflector with the screw holes on right side of the chassis.

Step 3 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4 Place the air deflector cover on the rear end of the chassis.

Step 5 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 2 of Figure 4-29).

Step 6 Place the mounting bracket flush against the left side of the chassis (see Diagram 2 of Figure 4-29).

Step 7 Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 8 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 9 Place the mounting bracket flush against the right side of the chassis (see Diagram 2 of Figure 4-29).

Step 10 Align the screw holes on the mounting bracket with the screw holes on the left side of the chassis.

Step 11 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 12 Place the left top air deflector flush against the left side of the chassis as shown in Diagram 3 of Figure 4-29.


Note If the 100G-LC-C, 10x10G-LC, or CFP-LC cards are to be installed in the ONS 15454 M2 shelf, do not mount the left top deflector (exhaust air deflector). Use the standard brackets directly to mount the ONS 15454 M2 shelf.


Step 13 Align the screw holes with the screw holes of the mounting bracket and the chassis.

Step 14 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See Diagram 4 of Figure 4-29.

Figure 4-29 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Step 15 Return to your originating procedure (NTP).


DLP-G589 Mount the ONS 15454 M2 Shelf on a Rack (One Person)

Purpose

This task allows one person to mount the shelf in a rack.

Tools/Equipment

# 2 Phillips Dynamometric screwdriver

ANSI—Two #12-24 x 3/4 pan-head Phillips mounting screws

ETSI—Two M6 x 20 mounting screws

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Note The ONS 15454 M2 requires a minimum of 3.5 inches (88.9 mm) of vertical rack space. To ensure that the mounting is secure, use two to three M6 mounting screws on each side of the shelf. A shelf should be mounted at the bottom of the rack if it is the only unit in the rack.



Note In an ANSI rack, the chassis can be installed in the front or the middle position. In an ETSI rack, the chassis is installed only in the front position.



Step 1 Verify that the proper fuse panel has been installed in the top mounting space. If a fuse panel is not present, you must install one according to manufacturer instructions:

For a DC power supply, the fuse rating must not exceed 15A.

For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes.

Step 2 Ensure that the shelf is mounted on the appropriate rack equipment:

23 inches (584.2 mm) or 19 inches (482.6 mm) for ANSI racks. The recommended 19-inch ANSI rack for the ONS 15454 M2 shelf is shown in Figure 1-1.

600 x 600-mm (23.6 x 23.6-inch) or 600 x 300-mm (23.6 x 11.8-inch) for ETSI racks.

Diagram 1 of Figure 4-30 shows the ONS 15454 M2 shelf mounted on an ANSI rack in the middle position using 19-inch mounting brackets

Diagram 2 of Figure 4-30 shows the ONS 15454 M2 shelf mounted on an ETSI rack in the front position using mounting brackets

Figure 4-30 Mounting an ONS 15454 M2 in a Rack

Step 3 Lift the shelf to the desired position in the rack.


Note To ensure proper cooling of the ONS 15454 M2 shelf, make sure that the space in front of the air flow vents are free of cables, fibers, and mechanical fixtures for fiber and cable management.


Step 4 Align the screw holes on the mounting brackets with the mounting holes in the rack.

Step 5 Using the Phillips Dynamometric screwdriver, install one mounting screw in each side of the assembly. Tighten the screw to a torque value of 22 in-lb (2.5 N-m).

Step 6 When the shelf is secured to the rack, install the remaining two mounting screws on either sides of the shelf.

Step 7 Return to your originating procedure (NTP).


DLP-G590 Mount the ONS 15454 M2 Shelf on the Wall

Purpose

This task explains how to mount the ONS 15454 M2 shelf on the wall.

Tools/Equipment

# 2 Phillips Dynamometric screwdriver

6 pan-head Phillips mounting screws

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Note The ONS 15454 M2 requires a minimum of 20.4-inches (518.16-mm) vertical length and a minimum of 25.5-inches (647.69-mm) horizontal width on the wall. Wall mount brackets are used to mount the ONS 15454 M2 shelf assembly on the wall. The type of screws used to mount the brackets on the wall depends on the wall-type and are not provided by Cisco. The screws used must be able to sustain an overall weight of at least 20 kg (44 lb).



Step 1 Verify that the proper fuse panel has been installed. If a fuse panel is not present, you must install one according to manufacturer instructions:

For a DC power supply, the fuse rating must not exceed 15A.

For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes.

Step 2 Mount the bracket on the wall as shown in Figure 4-31. To mount the bracket on a non-concrete wall, choose the bracket holes based on the wall structure. At least four screws must be used to mount the bracket on the wall.

Step 3 Align the mounting bracket screw holes against the shelf screw holes (see diagram 1 of Figure 4-31).

Step 4 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). See diagram 2 of Figure 4-31.

Figure 4-31 Wall Mounting of the ONS 15454 M2 Shelf

Step 5 Align the fire protective drip tray screw holes against the wall mounting bracket screw holes (see diagram 1 of Figure 4-30). The fire protective drip tray1 is present in the wall mount accessory kit2 provided by Cisco.

Step 6 Insert the screws and tighten them (see diagram 2 of Figure 4-30).

Figure 4-32 Mounting the Fire Protective Cove

Step 7 Return to your originating procedure (NTP).


DLP-G591 Mount the ONS 15454 M2 Shelf on the Desktop

Purpose

This task explains mount the shelf on the desktop.

Tools/Equipment

None

Prerequisite Procedures

G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Verify that the proper fuse panel has been installed. If a fuse panel is not present, you must install one according to manufacturer instructions:

For a DC power supply, the fuse rating must not exceed 15A.

For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes.

Step 2 Locate the rubber bumpers provided in the accessory tool kit.

Step 3 Place the ONS 15454 M2 shelf upside down on a smooth, flat surface.


Note To ensure proper cooling of the ONS 15454 M2 shelf, make sure that the space in front of the air flow vents are free of cables, fibers, and mechanical fixtures for fiber and cable management.


Step 4 Peel off the rubber bumpers from the adhesive strip and place it adhesive-side down onto all the four corners of the surface (see Figure 4-33).

Figure 4-33 Desktop Mounting of the ONS 15454 M2 Shelf

Step 5 Place the ONS 15454 M2 shelf on a desktop, or other flat and secure surface.

Step 6 Return to your originating procedure (NTP).


4.8  Front Door

The front door of the ONS 15454 M2 provides access to the shelf and air-filter.

There are two types of front doors that act as protective panels—standard door and deep-front panel. The deep-front panel provides additional space in front of the shelf to accommodate cables that do not fit inside the standard door. The deep-front panel does not have a hinge and cannot be rotated like the standard door.

If a standard front door was ordered, the ONS 15454 M2 is shipped with a preinstalled standard door. If a deep-front panel was ordered, it is shipped in a separate package.

You can remove the door to provide unrestricted access to the front of the shelf.

An erasable label is pasted on the inside of the front door. You can use the label to record slot and port assignments, card types, node ID, rack ID, and serial number of the ONS 15454 M2 shelf.

Figure 4-34 shows the erasable label on the ONS 15454 M2 shelf.

Figure 4-34 ONS 15454 M2 Front-Door Erasable Label

The laser warning label is placed on top of the chassis (see Figure 5-41).

Figure 4-35 shows the label placed on the ONS 15454 M2 surface, inside the shelf close to the door hinges, below Slot 1.

Figure 4-35 ONS 15454 M2 Label

NTP-G269 Install the Standard Door of the ONS 15454 M2 Shelf

Purpose

This procedure installs the standard door of the ONS 15454 M2

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G267 Install the Power Module in the ONS 15454 M2 Shelf

G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf

G271 Install the Power and Ground to the ONS 15454 M2 Shelf

G291 Attach Wires to Timing, LAN, and Craft Pin Connections in ONS 15454 M2

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Pull the hinge pins on the standard door in the opposite directions (see Figure 4-36).

Figure 4-36 Installing the Standard Door

Step 2 Align the standard door hinges with the chassis hinges.

Step 3 Release the hinge pins.


Note Reinstall the door after installing all the other modules.


Step 4 Place the ground strap cable (see Figure 4-37) on the door and the chassis and tighten the nuts.

Figure 4-37 Ground Strap Cable—Standard Door

Step 5 Tighten the door screws to a torque value of 6.5 in-lb (0.75 N-m) to close the standard door as shown in Figure 4-38.

Figure 4-38 Close the Standard Door of ONS 15454 M2 Shelf

Stop. You have completed this procedure.


NTP-G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf

Purpose

This procedure opens and removes the standard door of the ONS 15454 M2.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

G269 Install the Standard Door of the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Step 1 Complete the "DLP-G594 Open the Standard Door of the ONS 15454 M2 Shelf" task.

Step 2 Complete the "DLP-G595 Remove the Standard Door of the ONS 15454 M2 Shelf" task.

Stop. You have completed this procedure.


DLP-G594 Open the Standard Door of the ONS 15454 M2 Shelf

Purpose

This task opens the standard door of the ONS 15454 M2 system.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

G269 Install the Standard Door of the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution The ONS 15454 M2 shelf has an ESD plug input and is shipped with an ESD wrist strap. The ESD plug input is located on the outside of the shelf on the right side. It is labeled "ESD" on the top and bottom. Always wear an ESD wrist strap and connect the strap to the ESD plug when working on the ONS 15454 M2. For detailed instructions on how to wear the ESD wristband, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.


Step 1 Loosen the standard door screws (see Figure 4-39).

Step 2 Push the latches in the opposite direction as shown in the Figure 4-39.

Figure 4-39 Opening the Standard Door

Step 3 Swing the door open (see Figure 4-37).

Figure 4-40 Cisco ONS 15454 M2 Standard Door—Opened

Step 4 Return to your originating procedure (NTP).


DLP-G595 Remove the Standard Door of the ONS 15454 M2 Shelf

Purpose

This task removes the standard door of the ONS 15454 M2 system.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Prerequisite Procedures

G594 Open the Standard Door of the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Unscrew the nut holding the ground cable to the shelf. Remove the nut.

Step 2 Remove the ground cable from the shelf (see Figure 4-41).

Figure 4-41 Removing the Standard Door

Step 3 Pull the hinge pins holding the door to the chassis, in the opposite direction (see Figure 4-42).

Step 4 Remove the door from its hinges (see Figure 4-42).

Figure 4-42 Removing the Standard Door

Step 5 Return to your originating procedure (NTP).


NTP-G343 Install the Deep-Front Panel of the ONS 15454 M2 Shelf

Purpose

This procedure installs the deep-front panel of the ONS 15454 M2 shelf.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Socket (6/32 standard) and socket wrench to tighten or loosen the ground nut

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G267 Install the Power Module in the ONS 15454 M2 Shelf

G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf

G271 Install the Power and Ground to the ONS 15454 M2 Shelf

G291 Attach Wires to Timing, LAN, and Craft Pin Connections in ONS 15454 M2

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Note Use the deep front panel when ONS-SC+-10G-C pluggables are installed on ONS 15454 M2 shelf.



Caution The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep front panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454 M2 shelf.


Step 1 Connect the ground strap cable:

a. Loosen the ground nut from the shelf (see Figure 4-43).

b. Insert the lug of the ground strap cable and tighten the nut on the shelf to a torque value of 11.5 in-lb (1.3 N-m) (see Figure 4-43).

c. Route the other end of the ground strap cable outside the shelf at an angle of 180 degrees towards the left.

Figure 4-43 Inserting the Lug to the Shelf

Step 2 Loosen the deep-front panel screws and slide them outwards using the plastic tabs (see Figure 4-44).

Figure 4-44 Loosening the Deep-Front Panel screws

Step 3 Place the deep-front panel close to the shelf so that the shelf notches, and the deep-front panel retention features are in line (see Figure 4-45).

Figure 4-45 Moving Deep-Front Panel and Shelf in line

Step 4 Align the deep-front panel with the shelf by performing these sub-steps at the same time:

a. Align the right and left retention features of the deep-front panel with the right and left notches present on the top of the shelf (see Figure 4-45).

b. Align the deep-front panel pins present at the bottom of the panel with the shelf hinges (see Figure 4-46).

Figure 4-46 Aligning the Deep-Front Panel and Shelf

Figure 4-47 shows the deep-front panel aligned with the shelf.

Figure 4-47 Engaging the Deep-Front Panel and Shelf

Step 5 Slide the deep-front panel screws inwards using the plastic tabs to engage the retention features and the pins with the shelf notches and hinges (see Figure 4-48). Verify the engagement by gently applying outward pressure to the panel.

Figure 4-48 Engaging the Deep-Front Panel and Shelf

Step 6 Lock the deep-front panel by tightening the screws to a torque value of 6.5 in-lb (0.75 N-m).

Step 7 Connect the other end of the ground strap cable to the ground point present on the deep-front panel exterior.

Figure 4-49

Connecting the Ground Strap Cable

Stop. You have completed this procedure.


NTP-G331 Remove the Deep-Front Panel of the ONS 15454 M2 Shelf

Purpose

This procedure removes the deep-front panel of the ONS 15454 M2 system.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Socket (6/32 standard) and socket wrench to tighten or loosen the ground nut

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf

G343 Install the Deep-Front Panel of the ONS 15454 M2 Shelf

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep front panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454 M2 shelf.


Step 1 Remove the end of the ground strap cable that is connected to the exterior of the deep-front panel (see Figure 4-50).

Figure 4-50 Removing the end of the ground strap cable

Step 2 Loosen the deep-front panel screws and slide them outwards using the plastic tabs as shown in the Figure 4-51 to open the deep-front panel.

Figure 4-51 Moving the deep-front panel to disengage

Step 3 Move the deep-front panel away from the shelf (see Figure 4-52).

Figure 4-52 Moving the deep-front panel away

Step 4 Remove the ground strap cable from the shelf (see Figure 4-53):

Figure 4-53 Removing the ground strap cable

a. Loosen the ground nut on the shelf.

b. Remove the lug and tighten the nut on the shelf to a torque value of 11.5 in-lb (1.3 N-m).

Stop. You have completed this procedure.


4.9  Power Modules

The ONS 15454 M2 system contains the following pluggable power modules:

AC power module

DC power module

In addition to supplying power to the ONS 15454 M2 shelf, the power modules support the following connections:

LAN Connection—An Ethernet port (RJ-45) that supports the element manager system (EMS) connection. The RJ-45 port is used to connect the EMS or the craft interface terminal to access the ONS 15454 M2 shelf.

Passive Unit Inventory Interfaces (USB port)—The passive unit inventory interfaces are used to retrieve inventory information from passive devices such as, fiber trays, FBG DCU, patch panels, passive muxponder and demuxponder and so on. The inventory details are displayed in the Inventory tab in CTC.

Timing Connections—The BITS-IN port receives input from third party external sources called SSU (Synchronization Supply Unit) to synchronize the timing of the ONS 15454 M2 shelf. The BITS-OUT port provides output to external devices (other Cisco or third party shelves) to synchronize the timing signals with the ONS 15454 M6 shelf.

The ONS 15454 M2 shelf has a BITS-IN and BITS-OUT port on the power module. The BITS-IN and BITS-OUT connections are supported by:

Wire-wrap pins and mini-BNC connectors on the AC power module.

Mini-BNC connectors on the ETSI DC power module.

Wire-wrap pins on the ANSI DC power module.


Note For timing connection, use 100-ohm shielded BITS clock cable pair #22 or #24 AWG (0.51 mm² [0.020 inch] or 0.64 mm² [0.0252 inch]) twisted-pair T1-type.



Note Refer to Telcordia SR-NWT-002224 for rules about provisioning timing references.


4.9.1  AC Power Module

The AC power module converts the AC input current to DC output current.

Each AC power module has:

One AC single phase three poles (line L, Neutral N, and Protective Earth PE) input connector

One RJ-45 port for EMS connection

One USB port to support passive unit remote inventory connection

Two BITs connections (IN and OUT) for network synchronization supported by mini BNC

Two BITs connections (IN and OUT) for network synchronization supported by four wire-wrap pins

The AC power module has a single dual-color (red and green) LED on the faceplate. When the AC power line is not connected, the LED is OFF. Green LED indicates that the AC power line is connected and the power module is functioning properly. Red LED indicates that the AC power line is connected but an alarm is present due to secondary (48 V) fuse break. The shelf controller card controls the conditions that result in triggering the LED. The LED can be overwritten by the shelf controller card (TNC, TNCE, TSC, or TSCE) in all the three states (OFF/red/green). The AC power module supports the lamp test procedure and the LED changes its color or state. The fans in the ONS 15454 M2 shelf cool the AC module and guarantee proper operation across the complete operating temperature or output power range.

4.9.2  DC Power Module

The ONS 15454 M2 system can be powered by redundant DC power lines, however a single power line can power the entire ONS 15454 M2 system. The DC power module draws the power from the batteries to turn on the ONS 15454 M2.

Each ETSI DC power module has:

Two input battery connectors (two poles): -48V, RET for power terminals A and B.

One RJ-45 port for EMS connection

One USB port to support passive unit remote inventory connection

Two BITS connections (IN and OUT) for network synchronization that is supported by mini BNC

Each ANSI DC power module has:

Two terminal block connectors with -48V, RET for power terminals A and B

One RJ-45 port for EMS connection

One USB port to support passive unit remote inventory connection

Two BITS connections (IN and OUT) for network synchronization supported by four wire-wrap pins

The DC power module has a single dual-color (red and green) LED on the faceplate. When the battery is not connected, the LED is OFF. Green LED indicates that the battery is connected and the power module functions properly. Red LED indicates that the battery is connected but an alarm is present due to secondary fuse break (48 V). The DC power module does not support the lamp test procedure.

NTP-G267 Install the Power Module in the ONS 15454 M2 Shelf

Purpose

This procedure installs the power module in the ONS 15454 M2 system.

Tools/Equipment

#2 Phillips screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning The plug-socket combination must be accessible at all times because it serves as the main disconnecting device. Statement 1019

Note During the system startup or fan-tray replacement, the inventory data of the fan-tray assembly and the power module is displayed in the Inventory tab of CTC after a delay of approximately 6 minutes.



Step 1 Complete the necessary task as applicable:

"DLP-G592 Install the AC Power Module in the ONS 15454 M2 Shelf" task

"DLP-G593 Install the DC Power Module in the ONS 15454 M2 Shelf" task

Step 2 Complete the "NTP-G271 Install the Power and Ground to the ONS 15454 M2 Shelf" task.

Stop. You have completed this procedure.


DLP-G592 Install the AC Power Module in the ONS 15454 M2 Shelf

Purpose

This procedure installs the AC power module in the ONS 15454 M2 system.

Tools/Equipment

#2 Phillips screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Step 1 Insert the AC power module in Slot A.

Figure 4-54 Installing the AC Power Module

Step 2 Plug the AC power module completely into the chassis.

Step 3 Tighten the screw to a torque value of 4 in-lb (0.45 N-m) to lock the power module in the chassis (see Figure 4-55).

Figure 4-55 AC Power Module Installed in the ONS 15454 M2 Shelf

Stop. You have completed this procedure.


DLP-G593 Install the DC Power Module in the ONS 15454 M2 Shelf

Purpose

This task installs the DC power module in the ONS 15454 M2 system.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Step 1 Insert the DC power module in Slot A (see Figure 4-56).

Figure 4-56 Installing the DC Power Module

Step 2 Plug the DC power module completely into the chassis.

Step 3 Tighten the screw to a torque value of 4 in-lb (0.45 N-m) to lock the power module in the chassis (see Figure 4-57).

Figure 4-57 DC Power Modules Installed in the ONS 15454 M2 Shelf

Step 4 Return to your originating procedure (NTP).


4.10  Fan-Tray Assembly

The fan-trays supported on the Cisco ONS 15454 M2 shelf are 15454-M2-FTA and 15454-M2-FTA2. The 15454-M2-FTA2 fan-tray provides increased airflow when compared to the 15454-M2-FTA fan-tray. The 15454-M2-FTA2 is compatible with R9.2.0 and later releases.

The fan-tray assembly is installed on the left side of the ONS 15454 M2 shelf. The fan-tray assembly is removable and holds the fan-control circuitry and the fans for the ONS 15454 M2 shelf.

There are four LEDs on the fan-tray assembly:

Three alarm LEDs (CRIT, MAJ, and MIN) that indicate whether a critical, major, or minor alarm is present anywhere on the ONS 15454 M2 shelf.

One fan fail LED that indicates fan failure.

When the fan-tray assembly is not functioning and the power line is not connected, the LED is OFF. A red LED indicates an alarm in the fan-tray assembly. A green LED indicates that the fan-tray assembly is functioning, the power line is connected, and the power module is functioning properly, the LED is green. When the power line is connected and if there is no TNC, TNCE, TSC, or TSCE card installed in the ONS 15454 M2 shelf, then the LED is OFF.

The shelf controller card controls the conditions that result in triggering the LEDs. The LED can be overwritten by the shelf controller card (TNC, TNCE, TSC, or TSCE) in all the three states (OFF/red/green). The fan-tray assembly supports the lamp test procedure.

The fan-tray assembly has an LCD screen that provides slot and port-level information for all card slots, and the number of critical, major, and minor alarms. The shelf controller card (TSC, TSCE, TNC, or TNCE) drives the 16 X 2 character LCD screen. The LCD screen displays the shelf name, IP address, and software version that is currently used. The display contrast is automatically adjusted for clear view. The three accessible push buttons (SLOT, STATUS, and PORT) on the fan-tray assembly are used to set the slot and port level parameters.


Note The fan-tray assembly should be installed only after installing the power module. During the system startup or fan-tray replacement, the inventory data of the fan-tray assembly and the power module is displayed in the Inventory tab of CTC after a delay of approximately 6 minutes.


After you install the fan-tray, you should only access it if a fan failure occurs. To clean and replace the fan-tray assembly, see the "Maintain the Node" chapter in the Cisco ONS 15454 DWDM Configuration Guide.


Note If the fan-tray assembly is removed from the shelf, wait for at least 5 seconds before plugging it back into the shelf. In the event the LCD display on the fan-tray assembly appears blank, remove the unit from the shelf, wait for at least 5 seconds and reinsert the unit into the shelf.


A back-up flash memory is fitted into the fan-tray assembly to support the database (DB) and image back-up in the single mode operation of the ONS 15454 M2.

4.10.1  Fan Speed

Fan speed is controlled by the TNC, TNCE, TSC, or TSCE card temperature sensors. The sensors measure the input air temperature at the fan-tray assembly. Fan speed options are low, medium, and high. If the TNC, TNCE, TSC, or TSCE card fails, the fans automatically shift to high speed. The temperature measured by the TNC, TNCE, TSC, or TSCE sensors appears on the LCD screen.

4.10.2  Fan Failure

If one or more fans fail on the fan-tray assembly, replace the entire assembly. You cannot replace individual fans. The red Fan Fail LED on the front of the fan-tray illuminates when one or more fans fail. The red Fan Fail LED clears after you install a working fan-tray.

NTP-G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf

Purpose

This procedure installs the 15454-M2-FTA or 15454-M2-FTA2 fan-tray assembly in the ONS 15454 M2 system.

Tools/Equipment

Small slot-head screwdriver

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G267 Install the Power Module in the ONS 15454 M2 Shelf.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Note The 15454-M2-FTA2 is compatible with R9.2.0 and later releases.



Caution Do not operate an ONS 15454 M2 shelf without an air filter. For information on the air filter, see "G114 Inspect and Replace the Air Filter" section.


Caution Do not force a fan-tray module into place. Doing so can damage either the connectors on the fan-tray or the connectors on the backpanel of the shelf, or both.


Note Error messages appear on the TNC, TNCE, TSC, or TSCE card, the fan-tray LED, and in the Cisco Transport Controller (CTC) when the fan-tray module is removed from the shelf or when one fan is not working.



Note During the system startup or fan-tray replacement, the inventory data of the fan-tray assembly and the power module is displayed in the Inventory tab of CTC after a delay of approximately 6 minutes.



Note To install the fan-tray assembly, it is not necessary to move any of the fiber-routing facilities.



Step 1 Insert the fan-tray assembly in Slot B of the ONS 15454 M2 chassis (see Figure 4-58).

Figure 4-58 Installing the Fan-Tray Assembly

Step 2 Push the fan-tray assembly such that the backplane connector is completely engaged (see Figure 4-59).

Figure 4-59 Inserting the Fan-Tray Assembly in the ONS 15454 M2 Chassis

Step 3 Tighten the screw to a torque value of 4 in-lb (0.45 N-m) to lock the unit (see Figure 4-60).

Figure 4-60 Fan-Tray Assembly Installed in the ONS 15454 M2 Shelf

Step 4 To verify that the tray has plugged into the assembly, check the fan-tray and listen to determine if the fans are running.


Note If the fan-tray assembly is removed from the shelf, wait for at least 5 seconds before plugging it back into the shelf. In the event the LCD display on the fan-tray assembly appears blank, remove the unit from the shelf, wait for at least 5 seconds and reinsert the unit into the shelf.


Stop. You have completed this procedure.


4.11  Power and Ground Description

Ground the equipment according to Telcordia standards or local practices. The following sections describe power and ground for the ONS 15454 M2 shelves.

For detailed instructions on grounding the ONS 15454 M2 chassis, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

4.11.1  ANSI Power and Ground

For AC power feed, use the power cable shipped with the ONS 15454 M2 and one ground cable. For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes. The voltage rating value for AC power ranges between 100 VAC to 240 VAC depending on the standards in various countries. This product is intended for use on the TN and TT power systems.

The ONS 15454 M2 has redundant -48 VDC #12 single-hole lug power terminals. The terminals are labeled RET(A), RET(B), -48V(A), and -48V(B) on the power module.

To install redundant DC power feeds, use four power cables and one ground cable. For a single power feed, only two power cables (#12 AWG or larger, copper conductor, 194 degrees F [90 degrees C] minimum) and one ground cable (#6 AWG or larger) are required. Use a conductor with low impedance to ensure circuit overcurrent protection. However, the conductor must have the capability to safely conduct any faulty current that might be imposed. For a DC power supply, the fuse rating must not exceed 15A. The voltages -40.5 VDC and -57.6 VDC are, respectively, the minimum and maximum voltages required to power the chassis. The nominal steady state voltage is -48 VDC.


Note Functionality is guaranteed at -40 VDC input voltage, as defined in Telcordia GR-1089-CORE, Issue 5.


We recommend the following wiring conventions, but customer conventions prevail:

Red wire for battery connections (-48 VDC).

Black wire for battery return connections (RET).

The battery return connection is treated as DC-I, as defined in Telcordia GR-1089-CORE, Issue 3.

The ground lug must be a dual-hole type, UL Listed, CSA certified and rated to accept the #6 AWG cable. Two ground posts with two M5 nuts are provided on the ONS 15454 M2 to accommodate the dual-hole lug.

4.11.2  ETSI Power and Ground

The ONS 15454 M2 for ETSI has redundant -48 VDC power connectors (DSUB for DC power module) on the DC power module. To install redundant power feeds, use the two power cables shipped with the ONS 15454 M2 shelf and one ground cable. For a DC power supply, the fuse rating must not exceed 15A. The voltages -40.5 VDC and -57.6 VDC are, respectively, the minimum and maximum voltages required to power the chassis. The nominal steady state voltage is -48 VDC.

For AC power feed, use the power cable shipped with the ONS 15454 M2 and one ground cable. For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes. The voltage rating value for AC power ranges between 100 VAC to 240 VAC depending on the standards in various countries. This product is intended for use on the TN and TT power systems.


Caution Only use the power cables shipped with the ONS 15454 M2 shelf.

NTP-G271 Install the Power and Ground to the ONS 15454 M2 Shelf

Purpose

This procedure installs power feeds and grounds the ONS 15454 M2 system.

Tools/Equipment

ANSI and ETSI:

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Screws

Ground cable 13.3-mm² (#6 AWG) stranded

Listed pressure dual-holes lugs suitable for #8 AWG copper conductors

Wire cutters

Wire strippers

Crimp tool

Fuse panel

ANSI only:

Power cable (from fuse panel to assembly), #8 AWG, copper conductors, 194 degrees F [90 degrees C])

Wire wrapper

ETSI only:

Power cable (from fuse panel to power modules), shipped with the ONS 15454 M2 ETSI

Two-hole grounding lug, shipped with the ONS 15454 M2 ETSI

Prerequisite Procedures

G267 Install the Power Module in the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning To ensure safety of personnel and equipment, do not connect any power cables into the power module until the module is completely installed into the chassis. Statement 389

Warning To reduce the risk of electric shock, switch on the power only after the power cord is completely installed into the power module. Statement 390

Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, power modules, and faceplates are in place. Statement 261

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Never install an AC power module and a DC power module in the same chassis. Statement 1050

Warning When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. Statement 1002

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units. Statement 246

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39

Warning Use copper conductors only. Statement 1025

Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950-1 based safety standards. Statement 1033

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 10A-20A, 100-240 VAC~. Statement 1005

Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022

Warning This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028

Caution Always use the supplied ESD wristband when working with a powered ONS 15454. For detailed instructions on how to wear the ESD wristband, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.


Step 1 Verify that the correct fuse panel is installed in the top mounting space:

For a DC power supply, the fuse rating must not exceed 15A.

For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes.

Step 2 Depending on the shelf and the power module installed, complete the necessary task:

G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf.

G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only).

G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only).

Step 3 Connect the office ground to the ONS 15454 M2 shelf. For detailed instructions on grounding, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

Step 4 Complete the "DLP-G600 Turn On and Verify DC Office Power on the ONS 15454 M2 Shelf" task.

Step 5 Continue with the "NTP-G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf" procedure.

Stop. You have completed this procedure.


DLP-G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf

Purpose

This task connects AC power to the ONS 15454 M2 shelf.

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Wire wrapper

Wire cutters

Wire strippers

Crimp tool

Fuse panel

Ground cable 13.3-mm² (#6 AWG) stranded. The PIDs of the power cables are listed in Table 4-2.

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf.

G267 Install the Power Module in the ONS 15454 M2 Shelf.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Note This product is intended for use on the TN and TT power systems.



Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning This equipment shall be connected to AC mains provided with a surge protective device (SPD) at the service equipment complying with NFPA 70, the National Electrical Code (NEC). Statement 7012

Caution The ONS 15454 M2 relies on the protective devices in the building installation to protect against short circuit, overcurrent and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.


Note Not more than 7 feet (2 m) of the power supply cable should be exposed between the equipment and the fiber storage tray.



Caution When terminating the frame ground, do not use soldering lug connectors, screwless (push-in) connectors, quick connect connectors, or other friction-fit connectors.


Note If the system loses power or if both TNC, TNCE, TSC, or TSCE cards are reset, you must reset the ONS 15454 M2 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the NTP-G24 Set Up Name, Date, Time, and Contact Information, page 5-15.



Step 1 Verify that the AC power module is installed in Slot A of the ONS 15454 M2.

Step 2 Attach the AC power cable to the cable connector in the AC power module (see Figure 4-61).

Figure 4-61 Connecting Office Power—AC Power Modules

Step 3 Close the cable clip to secure the power cable (see Figure 4-62).

Figure 4-62 Cable Clip to Secure the Power Cable

Step 4 Connect the power cable to the fuse panel or power source.


Note The voltage rating value for AC power ranges between 100 VAC to 240 VAC depending on the standards in various countries.



Note Turn on the power after installing the power cables.


Step 5 Return to your originating procedure (NTP).


Table 4-2 PIDs for AC Power Cables

Cable
PID

AC power cable - Japan right exit

15454-M-CBL-R-JPN=

AC power cable - China right exit

15454-M-CBL-R-CHI=

AC power cable - India right exit

15454-M-CBL-R-IND=

AC power cable - EU right exit

15454-M-CBL-R-EU=

AC power cable - ARG right exit

15454-M-CBL-RARG=

AC power cable - AUS right exit

15454-M-CBL-RAUS=

AC power cable - UK right exit

15454-M-CBL-R-UK=

AC power cable - KOR right exit

15454-M-CBL-RKOR=

AC power cable ANSI 110VAC right exit

15454-M-ACCBL-R=

AC power cable ANSI 220VAC right exit

15454-M-ACCBL-R2=

AC power cable for data center right exit

15454-M-ACL6-R=


DLP-G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only)

Purpose

This task connects DC power to the ONS 15454 M2 shelf (ANSI Only).

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Wire wrapper

Wire cutters

Wire strippers

Crimp tool

Open-end wrench or hex tube screw driver

Fuse panel

Power cable (from fuse panel to assembly), #8 AWG, copper conductors, 194 degrees F [90 degrees C])

Ground cable #6 AWG stranded

Listed pressure dual-holes lugs suitable for #8 AWG copper conductors

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf.

G267 Install the Power Module in the ONS 15454 M2 Shelf.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning Hazardous voltage or energy may be present on DC power terminals. Always replace cover when terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement 1075

Caution The ONS 15454 M2 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.


Note The battery return connection is treated as DC-I, as defined in Telcordia GR-1089-CORE Issue 5.



Note If the system loses power or both TNC, TNCE, TSC, or TSCE cards are reset and the system is not provisioned to get the time from a Network Time Protocol/Simple Network Time Protocol (NTP/SNTP) server, you must reset the ONS 15454 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the NTP-G24 Set Up Name, Date, Time, and Contact Information, page 5-15. If you are using the TNC, TNCE, TSC, or TSCE cards, the system clock will run for up to three hours. In this case, no action would be required.



Step 1 Connect the return cables of the power supply to the Earth ground located at the power supply side.

Step 2 Connect the office power according to the fuse panel engineering specifications.

Step 3 Measure and cut the cables as needed to reach the ONS 15454 M2 from the fuse panel.

Step 4 Dress the power according to local site practice.

Step 5 Strip 1/2 inch (12.7 mm) of insulation from all power cables that you will use.

Step 6 Crimp the lugs onto the ends of all power leads.

Step 7 Verify that the DC power module is installed in Slot A.

Step 8 Remove the screws from the terminal block protective cover from the DC power module (see Figure 4-63).

Figure 4-63 Connecting Office Power—DC Power Module (ANSI Only)

Step 9 Insert the lugs as shown in Figure 4-64.

Figure 4-64 Connecting Office Power—DC Power Module (ANSI Only)


Note There are two DC power terminals—A and B. Each power terminal is connected with two cables—one for RET and the other for -48V.


Step 10 Tighten the screws to a torque value of 7 in-lb (0.79 N-m) to lock the lugs.

Step 11 Tighten the screws to a torque value of 4 in-lb (0.45 N-m) of the terminal block protective cover on the DC power module (see Figure 4-65).


Note Use only pressure terminal connectors, such as ring and fork types, when terminating the battery, battery return, and frame ground conductors.


Figure 4-65 Connecting Office Power—DC Power Modules (ANSI Only)


Caution Before you make any crimp connections, coat all bare conductors (battery, battery return, and frame ground) with an appropriate antioxidant compound. Bring all unplated connectors, braided strap, and bus bars to a bright finish, then coat with an antioxidant before you connect them. You do not need to prepare tinned, solder-plated, or silver-plated connectors and other plated connection surfaces, but always keep them clean and free of contaminants.


Caution When terminating power, return (RET), and frame ground, do not use soldering lug, screwless (push-in) connectors, quick-connect, or other friction-fit connectors.

Step 12 Return to your originating procedure (NTP).


DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only)

Purpose

This task connects power to the ONS 15454 M2 shelf (ETSI Only).

Tools/Equipment

#2 Phillips Dynamometric screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Wire wrapper

Wire cutters

Wire strippers

Crimp tool

Fuse panel

Ground cable #6 AWG stranded. The PID of the DC power cable for ETSI left exit is 15454-M2-DCCBL-LE=.

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf.

G267 Install the Power Module in the ONS 15454 M2 Shelf.

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Warning Hazardous voltage or energy may be present on DC power terminals. Always replace cover when terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement 1075

Note The battery return connection is treated as DC-I, as defined in Telcordia GR-1089-CORE Issue 5.



Caution The ONS 15454 M2 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.


Note If the system loses power or both TNC, TNCE, TSC, or TSCE cards are reset and the system is not provisioned to get the time from a Network Time Protocol/Simple Network Time Protocol (NTP/SNTP) server, you must reset the ONS 15454 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the see the NTP-G24 Set Up Name, Date, Time, and Contact Information, page 5-15. If you are using the TNC, TNCE, TSC, or TSCE cards, the system clock will run for up to three hours. In this case, no action would be required.



Step 1 Connect the return cables of the power supply to the Earth ground located at the power supply side.

Step 2 Verify that the DC power module is installed in Slot A of the ONS 15454 M2.

Figure 4-66 Connecting Office Power—DC Power Module (ETSI Only)

Step 3 Attach the DC ETSI power cables to the DSUB power connectors of the DC power module (see Figure 4-67).

Step 4 Tighten the screws to a torque value of 4 in-lb (0.45 N-m) to secure the cable.

Figure 4-67 Connecting Office Power—DC Power Module (ETSI Only)


Note Use only pressure terminal connectors, such as ring and fork types, when terminating the battery, battery return, and frame ground conductors.



Caution Before you make any crimp connections, coat all bare conductors (battery, battery return, and frame ground) with an appropriate antioxidant compound. Bring all unplated connectors, braided strap, and bus bars to a bright finish, then coat with an antioxidant before you connect them. You do not need to prepare tinned, solder-plated, or silver-plated connectors and other plated connection surfaces, but always keep them clean and free of contaminants.


Caution When terminating power, return, and frame ground, do not use soldering lug, screwless (push-in) connectors, quick-connect, or other friction-fit connectors.

Step 5 Return to your originating procedure (NTP).


DLP-G599 Turn On and Verify AC Office Power on the ONS 15454 M2 Shelf

Purpose

This task measures the power to verify correct power and returns for the ONS 15454 M2 shelf.

Tools/Equipment

Voltmeter

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the office ground to chassis. For detailed instructions on grounding, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf.

G267 Install the Power Module in the ONS 15454 M2 Shelf.

G596 Connect Office Power (AC) to the ONS 15454 M2 Shelf

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution Do not apply power to the shelf until you complete all the installation steps.


Warning To ensure safety of personnel and equipment, do not connect any power cables into the power module until the module is completely installed into the chassis. Statement 389

Warning To reduce the risk of electric shock, switch on the power only after the power cord is completely installed into the power module. Statement 390

Step 1 To power up the node, insert the fuse into the fuse position according to site practice. The fuse rating must not exceed 15A in case of AC power.

Step 2 If the ONS 15454 M2 does not power up, check the voltage at the power source using a voltmeter. The voltage should be 100 to 240 VAC +/-10 percent.

Step 3 Return to your originating procedure (NTP).


DLP-G600 Turn On and Verify DC Office Power on the ONS 15454 M2 Shelf

Purpose

This task measures the power to verify correct power and returns for the ONS 15454 M2 shelf.

Tools/Equipment

Voltmeter

Prerequisite Procedures

G266 Install the ONS 15454 M2 Shelf.

Connect the office ground to chassis. For detailed instructions on grounding, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.

G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf.

G267 Install the Power Module in the ONS 15454 M2 Shelf.

G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only) (or)

G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only).

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution Do not apply power to the shelf until you complete all installation steps.


Warning To ensure safety of personnel and equipment, do not connect any power cables into the power module until the module is completely installed into the chassis. Statement 389

Warning To reduce the risk of electric shock, switch on the power only after the power cord is completely installed into the power module. Statement 390

Step 1 Using a voltmeter, verify the office battery and ground at the following points on the fuse panel:

a. To verify the power, place the black test lead of the voltmeter to the frame ground. Place the red test lead on the A-side connection and verify that it is between -40.5 VDC and -57.6 VDC. Place the red test lead on the B-side connection and verify that it is between -40.5 VDC and -57.6 VDC.


Note The voltages -40.5 VDC and -57.6 VDC are, respectively, the minimum and maximum voltages required to power the chassis. The nominal steady state voltage is -48 VDC.


b. To verify the ground, place the black test lead of the voltmeter to the frame ground. Place the red test lead on the A-side return ground and verify that no voltage is present. Place the red test lead on the B-side return ground and verify that no voltage is present.

Step 2 To power up the node, insert the fuse into the fuse position according to site practice. The fuse rating must not exceed 15A.

Step 3 Using a voltmeter, verify the ONS 15454 M2 shelf for -48 VDC battery and ground:

a. To verify the A-side of the shelf, place the black lead of the voltmeter to the frame ground. Place the red test lead to the -48V (A-side battery connection) red cable. Verify that it reads between -40.5 VDC and -57.6 VDC. Then place the red test lead of the voltmeter to the RET1 (A-side return ground) black cable and verify that no voltage is present.


Note The voltages -40.5 VDC and -57.6 VDC are, respectively, the minimum and maximum voltages required to power the chassis.


b. To verify the B-side of the shelf, place the black test lead of the voltmeter to the frame ground. Place the red test lead to the -48V (B-side battery connection) red cable. Verify that it reads between -40.5 VDC and -57.6 VDC. Then place the red test lead of the voltmeter to the RET2 (B-side return ground) black cable and verify that no voltage is present.


Note To view the shelf voltage and temperature, refer to the "NTP-G230 View Shelf Voltage and Temperature" procedure.


Step 4 Return to your originating procedure (NTP).


NTP-G291 Attach Wires to Timing, LAN, and Craft Pin Connections in ONS 15454 M2

Purpose

This procedure attaches wires to the Timing, LAN, and Craft Pin connections in the ONS 15454 M2 shelf.

Tools/Equipment

Twisted #22 or #24 AWG (0.51 mm² or 0.64 mm²) shielded wires for LAN or craft 75-ohm coaxial cable with DIN 1.0/2.3 miniature coax connector.

Prerequisite Procedures

G267 Install the Power Module in the ONS 15454 M2 Shelf

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Caution Always use the supplied Electrostatic Discharge (ESD) wristband when working with a powered ONS 15454 M2. For detailed instructions on how to wear the ESD wristband, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.


Note To route the copper cables from the SFPs or RJ-45 ports in a ONS 15454 M2 shelf, removal of the shelf door is mandatory.



Note The minimum distance between the fiber LC connector and the bulk attenuator must be at least 50 cm. This is the minimum distance required to place the bulk attenuator outside the shelf from any port of a card.



Step 1 Complete either G292 Install Timing Wires in ONS 15454 M2 - ANSI or G293 Install Timing Wires in ONS 15454 M2 - ETSI if you are provisioning external timing.

Step 2 Complete G294 Install LAN Wires in ONS 15454 M2 to create an external LAN connection. You must connect a CAT-5 Ethernet cable to the LAN port on the TNC/TNCE/TSC/TSCE card to create an external LAN connection.

Step 3 Stop. You have completed this procedure.


DLP-G292 Install Timing Wires in ONS 15454 M2 - ANSI

Purpose

This task installs the timing wires in the DC-2 or AC-2 Power Module of ONS 15454 M2 (ANSI).

Tools/Equipment

100-ohm wire wrap cable, wire wrap tool

Prerequisite Procedures

None

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Locate the timing BITS connectors in the DC-2 or AC-2 Power Module, as shown in Figure 4-68 and Figure 4-69.

Figure 4-68 DC-2 Power Module ANSI BITS connectors

Figure 4-69 AC-2 Power Module ANSI BITS Connectors

Step 2 Connect the wire wrap cable to the appropriate timing connector in the Power Module.

Step 3 Connect the other end of the cable to the external source of the timing.

Repeat Step 3 for each cable that is needed.

Step 4 Return to your originating procedure (NTP).


DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI

Purpose

This task installs the timing wires in the AC-2 or DC-2E Power Module of ONS 15454 M2 (ETSI).

Tools/Equipment

75-ohm coaxial cable with a DIN 1.0/2.3 miniature coax connector. The PID for the BITS IN/OUT cable is 15454-M-TMGCBL=.

Prerequisite Procedures

None

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Locate the timing BITS connectors in the DC-2E or AC-2 Power Module, as shown in Figure 4-70 and Figure 4-71.

Figure 4-70 DC-2E Power Module ETSI BITS Connectors

Figure 4-71 AC-2 Power Module ETSI BITS Connectors

Step 2 Using a coaxial cable with DIN 1.0/2.3 miniature coax connectors, connect the clock cable to the appropriate connector in the Power Module.

Step 3 Gently push the cable with the DIN 1.0/2.3 miniature coax connector down until the cable connector slides into the DIN 1.0/2.3 miniature coax connector on the Power Module with a click. The Power Module provides DIN 1.0/2.3 miniature coax connectors that are used for timing input and output. The input connectors for timing provide a 75-ohm termination. System cables that can convert timing clocks from 75 ohms to 100/120 ohms are available.


Note See ITU-T G.813 for rules about provisioning timing references.


Step 4 Connect the other end of the cable to the external source of the timing.

Repeat Step 3 for each cable that is needed.

Step 5 Return to your originating procedure (NTP).


DLP-G294 Install LAN Wires in ONS 15454 M2

Purpose

This task installs the LAN wires in ONS 15454 M2.

Tools/Equipment

Standard CAT-5 Ethernet cable straight-through for data terminal equipment (DTE) or crossover for data circuit-terminating equipment (DCE) or RJ-45 connector

Crimping tool for RJ-45 connector

0.51 mm² or 0.64 mm² (#22 or #24 AWG) wire, preferably standard CAT-5

Prerequisite Procedures

G267 Install the Power Module in the ONS 15454 M2 Shelf

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

None



Step 1 Using a 0.51 mm² or 0.64 mm² (#22 or #24 AWG) wire or a standard CAT-5 Ethernet cable, connect the wires to the RJ-45 connector.

Step 2 Return to your originating procedure (NTP).


NTP-G313 Install and Configure the TNC, TNCE, TSC, or TSCE Card

Purpose

This procedure describes how to install and configure the TNC, TNCE, TSC, or TSCE card.

Tools/Equipment

Redundant TNC/TNCE/TSC/TSCE cards on Cisco ONS 15454 M6 shelf (required)

Stand-alone TNC/TNCE/TSC/TSCE card on Cisco ONS 15454 M2 shelf (required)

Prerequisite Procedures

G271 Install the Power and Ground to the ONS 15454 M2 Shelf

NTP-G14 Install DWDM Equipment, page 1-66

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

Provisioning or higher



Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94

Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M2 and ONS 15454 M6 shelf assemblies. For detailed instructions on how to wear the ESD wristband, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.


Note If you install a card incorrectly, the FAIL LED flashes continuously.



Step 1 Complete the "DLP-G604 Install the TNC, TNCE, TSC, or TSCE Card" task.


Note If you install the wrong card in a slot, see the NTP-G107 Remove Permanently or Remove and Replace DWDM Cards.


Step 2 Complete the "DLP-G605 Provision PPM and Port for the TNC and TNCE Cards" task.

Step 3 Complete the "DLP-G606 Configure UDC and VoIP for the TNC and TNCE Cards" task.

Stop. You have completed this procedure.


DLP-G604 Install the TNC, TNCE, TSC, or TSCE Card

Purpose

(ONS 15454 M2 and ONS 15454 M6 only) This task installs redundant TNC/TNCE/TSC/TSCE cards on the ONS 15454 M6 shelf and a stand-alone TNC/TNCE/TSC/TSCE card on the ONS 15454 M2 shelf. Install and initialize the TNC/TNCE/TSC/TSCE card before installing any other line cards into the shelf assemblies. On the ONS 15454 M6 shelf, install the TNC/TNCE/TSC/TSCE cards in slots 1 and 8 for redundancy. On the ONS 15454 M2 shelf, install the stand-alone TNC/TNCE/TSC/TSCE card in slot 1.

Tools/Equipment

Two TNC/TNCE/TSC/TSCE cards for the ONS 15454 M6 shelf and one TNC/TNCE/TSC/TSCE card for the ONS 15454 M2 shelf

Prerequisite Procedures

None

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution Do not remove the TNC/TNCE/TSC/TSCE cards during the software installation process, which is indicated by alternate flashing FAIL and ACT/STBY LEDs. Removing the TNC/TNCE/TSC/TSCE cards during the software installation process will corrupt the system memory.


Note Allow each TNC/TNCE/TSC/TSCE card to boot completely before installing the redundant TNC/TNCE/TSC/TSCE card.



Note On the ONS 15454 M6 shelf, install the TNC/TNCE/TSC/TSCE cards in slots 1 and 8 for redundancy. On the ONS 15454 M2 shelf, install the stand-alone TNC/TNCE/TSC/TSCE card in slot 1. For more information, see the "Card Slot Requirements" section.



Note You cannot insert the TNC/TNCE/TSC/TSCE cards in other slots due to mechanical constraints. To identify the card slot, match the symbol placed on the lower side of the card front panel with the symbol in the shelf.



Caution To achieve redundancy, two TNC or TNCE cards or two TSC or TSCE cards must be installed in the ONS 15454 M6 shelf. Do not install one TNC or TNCE card and a redundant TSC or TSCE card in the same shelf.


Step 1 Open the latches/ejectors of the first TNC/TNCE/TSC/TSCE card that you will install.

Step 2 Use the latches/ejectors to firmly slide the card horizontally along the guide rails until the card plugs into the receptacle at the back of the slot (slot 1 or 8 in the ONS 15454 M6 shelf and slot 1 in the ONS 15454 M2 shelf).

Step 3 Verify that the card is inserted correctly, and close the latches/ejectors on the card.

If you insert a card into a slot assigned for a different card, all LEDs turn off.

Step 4 As needed, verify the LED activity on the TNC/TNCE/TSC/TSCE card.

The red FAIL LED, PWR LED turn on briefly.

The red FAIL LED turns on for about 10 seconds.

The red FAIL LED and the amber ACT/STBY LED turn on for about 30 seconds.

The red FAIL LED blinks for about 10 seconds.

The red FAIL LED turns on for about 15 seconds.

All the LEDs including the CRIT, MAJ, MIN, REM, SYNC, and ACO LEDs blink once and turn off for about 10 seconds.

ACT/STBY LED blinks for about 1 second.

All the LEDs including the CRIT, MAJ, MIN, REM, SYNC, and ACO LEDs turn off for about 10 seconds.

The ACT/STBY, ACO, and PWR LEDs turn on.

The boot-up process is complete when the PWR LEDs turn green and the amber ACT/STBY remains on. The ACT/STBY LED turns green if this is the first TNC/TNCE/TSC/TSCE card installed, and amber if this is the second TNC/TNCE/TSC/TSCE card installed.


Note It might take up to four minutes for the power alarms to clear.



Note Alarm LEDs might be on. After completing the TNC/TNCE/TSC/TSCE card installation, log in to CTC and click the Alarms tab to display the alarms raised on the card. For procedure to clear the alarm, see the Cisco ONS DWDM Troubleshooting Guide.



Note During the TNC/TNCE/TSC/TSCE card initialization, the SFTWDOWN alarm appears twice. The alarm clears after the TNC/TNCE/TSC/TSCE card boots completely.



Note If the FAIL LED is on continuously, see the tip in Step 8 about the TNC/TNCE/TSC/TSCE card automatic upload.


Figure 4-72 illustrates the installation of TNC and TNCE cards on ONS 15454 M6 shelf.

Figure 4-72 Installing TNC and TNCE cards on ONS 15454 M6 Shelf

Step 5 Verify that the ACT/STBY LED is green if this is the first powered-up TNC/TNCE/TSC/TSCE card installed or amber if this is the second powered-up TNC/TNCE/TSC/TSCE. The IP address, temperature of the node, and time of day appear on the LCD. The default time and date is 12:00 AM, January 1, 1970.

Step 6 The LCD cycles through the IP address (the default is 192.1.0.2), node name, and software version. Verify that the correct software version is shown on the LCD. The software text string indicates the node type (SDH or SONET) and software release. (For example: SDH 09.20-05L-20.10 indicates it is an SDH software load, Release 9.2. The numbers following the release number do not have any significance.)

Step 7 If the LCD shows the correct software version, continue with Step 8. If the LCD does not show the correct software version, refer to your next level of technical support, upgrade the software, or remove the TNC/TNCE/TSC/TSCE card and install a replacement card. Refer to the release-specific software upgrade document to replace the software.

Step 8 (ONS 15454 M6 shelf only) Repeat Steps 1 through 7 for the redundant TNC/TNCE/TSC/TSCE card.


Tip If you install a standby TNC/TNCE/TSC/TSCE card that has a different software version than the active TNC/TNCE/TSC/TSCE card, the standby TNC/TNCE/TSC/TSCE card copies the software version from the active TNC/TNCE/TSC/TSCE card. When the standby card is first inserted, the LEDs follow the normal boot-up sequence. However, after the red FAIL LED turns on for about 5 seconds, the FAIL LED and the ACT/STBY LED begin to flash alternately for up to 30 minutes. After loading the new software, the upgraded TNC/TNCE/TSC/TSCE cards LEDs repeat the appropriate bootup sequence, and the amber ACT/STBY LED turns on.


Step 9 Return to your originating procedure (NTP).


DLP-G605 Provision PPM and Port for the TNC and TNCE Cards

Purpose

(ONS 15454 M2 and ONS 15454 M6 only) This task provisions a PPM and port on a TNC and TNCE cards. PPMs are created to support the OSC function.

Tools/Equipment

None

Prerequisite Procedures

DLP-G46 Log into CTC, page 4-30

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

None



Step 1 In node view (single-shelf mode) or shelf view (multishelf view), double-click the TNC and TNCE cards where you want to provision PPM and port settings.

Step 2 Click the Provisioning > Pluggable Port Modules tabs.

Step 3 In the Pluggable Port Modules area, click Create. The Create PPM dialog box appears.

Step 4 In the Create PPM dialog box, complete the following:

PPM—Choose 1 or 2 from the PPM drop-down list.

PPM Type—Displays the PPM associated with the chosen PPM in the above step.

Step 5 Click OK. The newly created PPM appears in the Pluggable Port Modules area. The row in the Pluggable Port Modules area becomes white when the PPM is inserted and the Actual Equipment Type column lists the name of PPM.

Step 6 In the Pluggable Ports area, click Create. The Create Port dialog box appears.

Step 7 In the Create Ports dialog box, complete the following:

Port—Choose the port you want to configure from the Port drop-down list.

Port Type—Choose the port type, such as OC-3, FE, or ONE-GE from the Port Type drop-down list.


Note OC-3 can be configured only on PPM port 1. FE and ONE-GE can be configured on both the ports.


Step 8 Click OK. The newly created port appears in the Pluggable Ports area. The port type you provisioned is listed in the Rate column.

Step 9 Repeat Steps 3 through 8 to provision another PPM and port on the TNC and TNCE cards.

Step 10 Return to your originating procedure (NTP).


DLP-G606 Configure UDC and VoIP for the TNC and TNCE Cards

Purpose

(ONS 15454 M2 and ONS 15454 M6 only) This task configures UDC and VoIP traffic for the TNC and TNCE cards.

Tools/Equipment

None

Prerequisite Procedures

DLP-G46 Log into CTC, page 4-30

NTP-G38 Provision OSC Terminations, page 5-121

G605 Provision PPM and Port for the TNC and TNCE Cards

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

None



Note Each TNC and TNCE cards support UDC/VoIP configuration. You can configure UDC or VoIP on the two SFP ports present on the TNC and TNCE cards. The TNC and TNCE cards support the UDC/VoIP configuration only when OSC is provisioned on the SFP ports.



Note If two nodes are connected through the fiber and if the TNC and TNCE cards in one node has UDC configuration, the TNC and TNCE cards in the other node must also have UDC configuration. The same rule applies to VoIP configuration.



Step 1 In node view (single-shelf mode) or shelf view (multishelf view), double-click the TNC and TNCE cards where you want to configure UDC and VoIP.

Step 2 Click the Provisioning > UDC / VOIP tabs.

Step 3 From the Service Type drop-drop list, choose UDC or VOIP.


Note You can configure UDC or VoIP on only one SFP port at a time per TNC and TNCE cards. If you want to configure UDC or VoIP on the second SFP port, choose NONE from the Service Type drop-down list for the first port and then choose UDC or VoIP for the second port.


Step 4 Click Apply.

Step 5 Return to your originating procedure (NTP).


NTP-G275 Perform the ONS 15454 M2 Shelf Installation Acceptance Test

Purpose

Use this procedure to perform a shelf installation acceptance test for the ONS 15454 M2.

Tools/Equipment

Voltmeter

Prerequisite Procedures

Applicable procedures in Chapter 4 "Installing the ONS 15454 M2 Shelf"

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Step 1 If you installed an ONS 15454 M2 shelf, complete Table 4-3 by verifying that each applicable procedure was completed.


Step 2 Complete the "DLP-G601 Inspect the ONS 15454 M2 Shelf Installation and Connections" task.

Step 3 Complete the "DLP-G602 Measure DC Voltage on the ONS 15454 M2 Shelf" task.

Step 4 Continue with Chapter 4, "Connect the PC and Log into the GUI."

Stop. You have completed this procedure.


DLP-G601 Inspect the ONS 15454 M2 Shelf Installation and Connections

Purpose

Use this task to inspect the shelf installation and connections and verify that everything is installed and connected properly.

Tools/Equipment

None

Prerequisite Procedures

None

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Step 1 Make sure all external wiring connections (that is, power, ground, alarms, and so on) are secure. If a wire or cable is loose, return to the appropriate procedure in this chapter to correct it.

Step 2 Return to your originating procedure (NTP).


DLP-G602 Measure DC Voltage on the ONS 15454 M2 Shelf

Purpose

Use this task to measure the power to verify correct power and returns.

Tools/Equipment

Voltmeter

Prerequisite Procedures

Before installing the DC power, check the voltage

Required/As Needed

Required

Onsite/Remote

Onsite

Security Level

None



Caution Do not apply power to the shelf until you complete all the installation steps.


Warning To ensure safety of personnel and equipment, do not connect any power cables into the power module until the module is completely installed into the chassis. Statement 389

Warning To reduce the risk of electric shock, switch on the power only after the power cord is completely installed into the power module. Statement 390

Step 1 Using a voltmeter, verify the office ground and power:

a. Place the black lead (positive) on the frame ground on the bay. Hold it there while completing Step a.

a. Place the red lead (negative) on the fuse power points on the third-party power distribution panel to verify that they read between -40.5 VDC and -57.6 VDC (power) and 0 (return ground).

Step 2 Using a voltmeter, verify the shelf ground and power wiring:

a. Place the black lead (positive) on the RET1(A) and the red lead on the -48V (A) point. Verify a reading between -40.5 VDC and -57.6 VDC. If there is no voltage, check the following and correct if necessary:

Battery and ground are reversed to the shelf.

Battery is open or missing.

Return is open or missing.

Step 3 Repeat Step 1 and Step 2 for the RET2 (B) and -48V (B) of the redundant power supply input.

Step 4 Return to your originating procedure (NTP).


4.12  Filler Card

The line card filler (15454-M-FILLER) must be installed in unused and empty slots to ensure proper air flow and electromagnetic interference (EMI) requirements during the ONS 15454 M2 operation. They can be installed in Slot 2 and Slot 3 and have no card-level LED indicators.

CTC does not detect filler cards in R9.2. This support may be added in later releases. Figure 5-106 shows the line card filler.

4.13  Air Filter

The ONS 15454 M2 contains a preinstalled reusable air filter (15454 M2-FTF) on the right side of the shelf.

The reusable filter is made up of a gray, open-cell, polyurethane foam that is specially coated to provide fire and fungi resistance. Spare filters should be kept in stock. Inspect the air filter every 30 days, and clean the filter every three to six months. The air filter can be replaced without removing the fan-tray assembly. However, the fan-tray must be turned off to remove the air filter. Replace the air filter every two to three years. Avoid cleaning the air filter with harsh cleaning agents or solvents.


Caution Do not operate an ONS 15454 M2 without the mandatory air filter.

4.14  Shelf Voltage and Temperature


Note The temperature measured by the TNC, TNCE, TSC, or TSCE sensors appears on the LCD screen in the ONS 15454 M2 chassis.


The input voltages and temperature of the ONS 15454 M2 chassis are displayed in the Shelf view > Provisioning > General > Voltage/Temperature pane in CTC. The voltage supplied to the shelf (in millivolts) is displayed in the Voltage area of the Voltage/Temperature pane. The temperature of the shelf (in degree Celsius) is displayed in the Temperature area of the pane.

The Voltage/Temperature pane retrieves the following values for the ONS 15454 M2 chassis:

Voltage A—Voltage of the shelf that corresponds to power supply A, in millivolts.

Voltage B—Voltage of the shelf that corresponds to power supply B, in millivolts.

Chassis Temperature—Temperature of the shelf, in degrees Celsius.

In multishelf configuration, the voltage and temperature of each shelf is displayed in the Shelf view > Provisioning > General > Voltage/Temperature pane.

1 The part number of the fire protective drip tray is 700-31085-xx.
2 The product identifier (PID) of the wall mount accessory kit is 15454-M2-WM PID and the part number is 53-3337-xx.