IP Routing: OSPF Configuration Guide, Cisco IOS Release 15S
OSPF Forwarding Address Suppression in Translated Type-5 LSAs
Downloads: This chapterpdf (PDF - 1.26MB) The complete bookPDF (PDF - 5.68MB) | The complete bookePub (ePub - 1.22MB) | The complete bookePub (ePub - 1.21MB) | Feedback

OSPF Forwarding Address Suppression in Translated Type-5 LSAs

OSPF Forwarding Address Suppression in Translated Type-5 LSAs

The OSPF Forwarding Address Suppression in Translated Type-5 LSAs feature causes a not-so-stubby area (NSSA) area border router (ABR) to translate Type-7 link state advertisements (LSAs) to Type-5 LSAs, but use the address 0.0.0.0 for the forwarding address instead of that specified in the Type-7 LSA. This feature causes routers that are configured not to advertise forwarding addresses into the backbone to direct forwarded traffic to the translating NSSA ABRs.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for OSPF Forwarding Address Suppression in Translated Type-5 LSAs

This document presumes you have OSPF configured on the networking device; it does not document other steps to configure OSPF.

Information About OSPF Forwarding Address Suppression in Translated Type-5 LSAs

Benefits of OSPF Forwarding Address Suppression in Translated Type-5 LSAs

The OSPF Forwarding Address Suppression in Translated Type-5 LSAs feature causes an NSSA ABR to translate Type-7 LSAs to Type-5 LSAs, but use the 0.0.0.0 as the forwarding address instead of that specified in the Type-7 LSA. This feature causes routers that are configured not to advertise forwarding addresses into the backbone to direct forwarded traffic to the translating NSSA ASBRs.

When to Suppress OSPF Forwarding Address in Translated Type-5 LSAs

In the figure below, it would be advantageous to filter Area 2 addresses from Area 0 to minimize the number of routes introduced into the backbone (Area 0). However, using the area rangecommand to consolidate and summarize routes at the area boundary--filtering the Area 2 addresses--will not work because the Area 2 addresses include forwarding addresses for Type-7 LSAs that are generated by the ASBR. If these Type-7 LSA forwarding addresses have been filtered out of Area 0, the backbone routers cannot reach the prefixes advertised in the translated Type-5 LSAs (autonomous system external LSAs).

Figure 1. OSPF Forwarding Address Suppression in Translated Type-5 LSAs

This problem is solved by suppressing the forwarding address on the ABR so that the forwarding address is set to 0.0.0.0 in the Type-5 LSAs that were translated from Type-7 LSAs. A forwarding address set to 0.0.0.0 indicates that packets for the external destination should be forwarded to the advertising OSPF router, in this case, the translating NSSA ABR.

Before configuring this feature, consider the following caution.


Caution


Configuring this feature causes the router to be noncompliant with RFC 1587. Also, suboptimal routing might result because there might be better paths to reach the destination’s forwarding address. This feature should not be configured without careful consideration and not until the network topology is understood.


How to Suppress OSPF Forwarding Address in Translated Type-5 LSAs

Suppressing OSPF Forwarding Address in Translated Type-5 LSAs


Caution


Configuring this feature causes the router to be noncompliant with RFC 1587. Also, suboptimal routing might result because there might be better paths to reach the destination’s forwarding address. This feature should not be configured without careful consideration and not until the network topology is understood.


SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    router ospf process-id

    4.    area area-id nssa translate type7 suppress-fa

    5.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables higher privilege levels, such as privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 router ospf process-id


    Example:
    Router(config)# router ospf 1 
     

    Enables OSPF routing and enters router configuration mode.

    • The process-id argument identifies the OSPF process.
     
    Step 4 area area-id nssa translate type7 suppress-fa


    Example:
    Router(config-router)# area 10 nssa translate type7 suppress-fa
     

    Configures an area as a not-so-stubby-area (NSSA) and suppresses the forwarding address in translated Type-7 LSAs.

     
    Step 5 end


    Example:
    Router(config-router)# end
     

    Exits configuration mode and returns to privileged EXEC mode.

     

    Configuration Examples for OSPF Forwarding Address Suppression in Translated Type-5 LSAs

    Example Suppressing OSPF Forwarding Address in Translated Type-5 LSAs

    This example suppresses the forwarding address in translated Type-5 LSAs:

    interface ethernet 0
     ip address 10.93.1.1 255.255.255.0
     ip ospf cost 1
    !
    interface ethernet 1
     ip address 10.94.1.1 255.255.255.0
    !
    router ospf 1
     network 10.93.0.0 0.0.255.255 area 0.0.0.0
     network 10.94.0.0 0.0.255.255 area 10
     area 10 nssa translate type7 suppress-fa

    Additional References

    Related Documents

    Related Topic

    Document Title

    OSPF commands

    Cisco IOS IP Routing: OSPF Command Reference

    OSPFv3 Address Families

    OSPFv3 Address Families” module

    Standards

    Standards

    Title

    No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

    --

    MIBs

    MIBs

    MIBs Link

    No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

    To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

    http:/​/​www.cisco.com/​go/​mibs

    RFCs

    RFCs

    Title

    Configuring the OSPF Forwarding Address Suppression in Translated Type-5 LSAs feature causes the router to be noncompliant with RFC 1587.

    The OSPF NSSA Option

    Technical Assistance

    Description

    Link

    The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

    Feature Information for OSPF Forwarding Address Suppression in Translated Type-5 LSAs

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Table 1 Feature Information for OSPF Forwarding Address Suppression in Translated Type-5 LSAs

    Feature Name

    Releases

    Feature Information

    OSPF Forwarding Address Suppression in Translated Type-5 LSAs

    12.2(15)T 12.2(18)S 12.2(27)SBC Cisco IOS XE 3.1.0 SG

    The OSPF Forwarding Address Suppression in Translated Type-5 LSAs feature causes a not-so-stubby area (NSSA) area border router (ABR) to translate Type-7 link state advertisements (LSAs) to Type-5 LSAs, but to use the address 0.0.0.0 for the forwarding address instead of that specified in the Type-7 LSA. This feature causes routers that are configured not to advertise forwarding addresses into the backbone to direct forwarded traffic to the translating NSSA ABRs.

    The following commands are introduced or modified:

    • area nssa translate
    • show ip ospf