IP Routing BFD Configuration Guide, Cisco IOS XE Release 3S
Bidirectional Forwarding Detection
Downloads: This chapterpdf (PDF - 1.72MB) The complete bookPDF (PDF - 2.93MB) | The complete bookePub (ePub - 386.0KB) | Feedback

Bidirectional Forwarding Detection

Contents

Bidirectional Forwarding Detection

This document describes how to enable the Bidirectional Forwarding Detection (BFD) protocol. BFD is a detection protocol that is designed to provide fast forwarding path failure detection times for all media types, encapsulations, topologies, and routing protocols. It includes a description of how to configure multihop BFD sessions.

BFD provides a consistent failure detection method for network administrators, in addition to fast forwarding path failure detection. Because the network administrator can use BFD to detect forwarding path failures at a uniform rate, rather than the variable rates for different routing protocol hello mechanisms, network profiling and planning will be easier, and reconvergence time will be consistent and predictable.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Bidirectional Forwarding Detection

  • Cisco Express Forwarding and IP routing must be enabled on all participating routers.
  • You must enable Cisco Parallel eXpress Forwarding (PXF) on the Cisco 10720 Internet router in order for BFD to operate properly. PXF is enabled by default and is generally not turned off.
  • One of the IP routing protocols supported by BFD must be configured on the routers before BFD is deployed. You should implement fast convergence for the routing protocol that you are using. See the IP routing documentation for your version of Cisco IOS software for information on configuring fast convergence. See the Restrictions for Bidirectional Forwarding Detection section for more information on BFD routing protocol support in Cisco IOS software.
  • Before Virtual Circuit Connection Verification (VCCV) BFD on pseudowires can be run, pseudowires must be configured on the network.
  • In Cisco IOS Release 15.1(2)S and later releases, support for offloading BFD sessions to ES+ line cards on Cisco 7600 series routers has the following prerequisites:
    • The router must be running BFD Version 1.
    • The BFD session type must be IPv4 single hop.
    • BFD echo mode must be disabled for the session.
    See the “Configuring Synchronous Ethernet on the Cisco 7600 Router with ES+ Line Card” section of the Cisco 7600 Series Ethernet Services Plus (ES+) and Ethernet Services Plus T (ES+T) Line Card Configuration Guide for more information about prerequisites for hardware offload.
  • In Cisco IOS Release 15.1(3)S and later releases, support for multihop BFD sessions on Cisco 7600 series routers has the following prerequisites:
    • The client must support multihop.
    • A valid multihop template and map must be configured..
    • Each BFD multihop session must have a unique source-destination address pair.

Restrictions for Bidirectional Forwarding Detection

  • With CSCts32440, the maximum number of supported VRF-aware IS-IS BFD sessions is 28.
  • For the Cisco implementation of BFD for Cisco IOS Releases 12.2(18)SXE, 12.0(31)S, 12.4(4)T, 12.0(32)S, 12.2(33)SRA, and 12.2(33)SRB, only asynchronous mode is supported. In asynchronous mode, either BFD peer can initiate a BFD session.
  • For Cisco IOS Releases 12.2(33)SRC, 12.2(33)SXH, and 12.2(33)SXI, echo mode is the default.
  • The Cisco IOS software incorrectly allows configuration of BFD on virtual-template and dialer interfaces; however, BFD functionality on virtual-template and dialer interfaces is not supported. Avoid configuring BFD on virtual-template and dialer interfaces.
  • For Cisco IOS Releases 12.2(18)SXE (and later SX releases), 12.0(31)S, 12.4(4)T, 12.0(32)S, 12.2(33)SRA, 12.2(33)SRB, 12.2(33)SRC, and 12.2(33)SB, the Cisco implementation of BFD is supported only for IPv4 networks.
  • For Cisco IOS Release 12.2(33)SRB, the Cisco implementation of BFD supports only the following routing protocols: Border Gateway Protocol (BGP), Enhanced Interior Gateway Routing Protocol (EIGRP), Intermediate System-to-Intermediate System (IS-IS), and Open Shortest Path First (OSPF). In Cisco IOS Release 12.2(33)SRC, BFD supports static routing.
  • For Cisco IOS Release 12.2(33)SRA, the Cisco implementation of BFD supports only the following routing protocols: BGP, IS-IS, and OSPF.
  • For Cisco IOS Release 12.4(4)T, the Cisco implementation of BFD supports only the following routing protocols: BGP, EIGRP, IS-IS, and OSPF.
  • For Cisco IOS Release 12.4(11)T, the Cisco implementation of BFD introduced support for the Hot Standby Router Protocol (HSRP). BFD support is not available for all platforms and interfaces.
  • For Cisco IOS Releases 12.0(31)S and 12.0(32)S, the Cisco implementation of BFD supports only the following routing protocols: BGP, IS-IS, and OSPF.
  • For Cisco IOS Release 12.2(18)SXE, the Cisco implementation of BFD supports only the following routing protocols: EIGRP, IS-IS, and OSPF.
  • For Cisco IOS Release 12.2(18)SXH and 12.2(33)SB, the Cisco implementation of BFD supports the following routing protocols: BGP, EIGRP, IS-IS, and OSPF.
  • BFD works only for directly connected neighbors. BFD neighbors must be no more than one IP hop away. Multihop configurations are not supported.
  • BFD support is not available for all platforms and interfaces. To confirm BFD support for a specific platform or interface and obtain the most accurate platform and hardware restrictions, see the Cisco IOS software release notes for your software version.
  • For the following Cisco IOS Releases, BFD on PortChannel is not a supported configuration: 12.2SXF, 12.2SRC, and 12.2SRB.
  • On the Cisco 10720 Internet router, BFD is supported only on Fast Ethernet, Gigabit Ethernet, and RPR-IEEE interfaces. BFD is not supported on Spatial Reuse Protocol (SRP) and Packet-over-SONET (POS) interfaces.
  • When you configure the BFD session parameters on a Cisco 10720 interface using the bfd command (in interface configuration mode), the minimum configurable time period supported for the milliseconds argument in both the interval milliseconds and min_rx milliseconds parameters is 50 milliseconds (ms).
  • A maximum of 100 BFD sessions is supported on the Cisco 10720 Internet router. When BFD tries to set up a connection between routing protocols and establish a 101th session between a Cisco 10720 Internet router and adjacent routers, the following error message is displayed:
    00:01:24: %OSPF-5-ADJCHG: Process 100, Nbr 10.0.0.0 on RPR-IEEE1/1 from LOADING to FULL, Loading Done
    00:01:24: %BFD-5-SESSIONLIMIT: Attempt to exceed session limit of 100 neighbors.
    
  • The Cisco 10720 Internet router does not support the following BFD features:
    • Demand mode
    • Echo packets
    • BFD over IP Version 6
  • On the Cisco 12000 series router, asymmetrical routing between peer devices may cause a BFD control packet to be received on a line card other than the line card that initiated the session. In this special case, the BFD session between the routing peers will not be established.
  • A maximum 100 sessions per line card are supported for the distributed Cisco 12000 series Internet router. The minimum hello interval is 50 ms with up to three Max retries for a BFD control packet to be received from a remote system before a session with a neighbor is declared down.
  • In Cisco IOS Release 12.2(33)SB, BFD is not stateful switchover (SSO) aware, and it is not supported with NSF/SSO and these features should not be used together. Enabling BFD along with NSF/SSO causes the nonstop forwarding capability to break during failover since BFD adjacencies are not maintained and the routing clients are forced to mark down adjacencies and reconverge.

BFD Control Channel over VCCV--Support for ATM Pseudowire

  • The BFD Control Channel over VCCV--Support for Asynchronous Transfer Mode Pseudowire feature supports VCCV type 1 only, without IP/User Datagram Protocol (UDP) encapsulation.
  • Any Transport over Multiprotocol Label Switching (AToM) is the only transport protocol supported by the BFD Control Channel over VCCV--Support for ATM Pseudowire feature.
  • Layer 2 Transport Protocol version 3 (L2TPv3) is not supported.
  • Pseudowire redundancy is not supported.
  • Only ATM attachment circuits (AC) are supported.

Cisco IOS Release 12.2(33)SXI2 and Cisco Catalyst 6500 Series Switches

  • Cisco Catalyst 6500 series switches support up to 100 BFD sessions with a minimum hello interval of 50 ms and a multiplier of 3. The multiplier specifies the minimum number of consecutive packets that can be missed before a session is declared down.
  • If SSO is enabled on a dual RP system, the following limitations apply:
    • The maximum number of BFD sessions supported is 50.
    • The minimum hello interval is 500 ms with a multiplier of 3 or higher.
    • If EIGRP is enabled, the maximum number of BFD sessions supported is reduced to 30.
    • Echo mode is supported on Distributed Forwarding Cards (DFCs) only.
  • BFD SSO is supported on Cisco Catalyst 6500 series switches using the E-chassis and 67xx line cards only. Centralized Forwarding Cards (CFCs) are not supported.
  • To enable echo mode the system must be configured with the no ip redirects command.
  • During the In Service Software Upgrade (ISSU) cycle the line cards are reset, causing a routing flap in the BFD session.

Cisco IOS Release 15.1(2)S and ES+ Line Cards for Cisco 7600 Series Routers

Cisco IOS Release 15.1(2)S, supports offloading BFD sessions to ES+ line cards on Cisco 7600 series routers. See the “Configuring Synchronous Ethernet on the Cisco 7600 Router with ES+ Line Card” section of the Cisco 7600 Series Ethernet Services Plus (ES+) and Ethernet Services Plus T (ES+T) Line Card Configuration Guide for more information about restrictions for hardware offload.

Cisco IOS Release 15.1(3)S-Support for BFD Multihop

  • Only IPv4 and IPv6 BFD multihop sessions are supported.
  • Multihop sessions will not be offloaded to hardware.
  • IPv6 link local addresses are not supported for BFD multihop sessions.
  • Echo mode is not supported in multihop.

Note


For the most accurate platform and hardware restrictions, see the Cisco IOS software release notes for your software version.


Support for Point-to-Point IPv4, IPv6, and GRE Tunnels

Depending on your release, Cisco software supports BFD forwarding on point-to-point IPv4, IPv6, and generic routing encapsulation (GRE) tunnels.

Only numbered interfaces are allowed. When the tunnel type is changed from a supported tunnel type to an unsupported one, BFD sessions are brought down for that tunnel and the BFD configuration is removed from the interface.

BFD detection time depends on the topology and infrastructure. For a single-hop IP tunnel that is deployed across physically adjacent devices, the 150 ms (that is, a hello interval of 50 ms with up to three retries) detection rate applies. However, when the source and destination endpoints of the tunnel are not connected back-to-back, the 150 ms detection rate is not guaranteed.

BFD uses the IP address configured on the tunnel interface. It does not use the tunnel source and destination addresses.

Information About Bidirectional Forwarding Detection

BFD Operation

BFD provides a low-overhead, short-duration method of detecting failures in the forwarding path between two adjacent routers, including the interfaces, data links, and forwarding planes.

BFD is a detection protocol that you enable at the interface and routing protocol levels. Cisco supports the BFD asynchronous mode, which depends on the sending of BFD control packets between two systems to activate and maintain BFD neighbor sessions between routers. Therefore, in order for a BFD session to be created, you must configure BFD on both systems (or BFD peers). Once BFD has been enabled on the interfaces and at the router level for the appropriate routing protocols, a BFD session is created, BFD timers are negotiated, and the BFD peers will begin to send BFD control packets to each other at the negotiated interval.

This section includes the following subsections:

Neighbor Relationships

BFD provides fast BFD peer failure detection times independently of all media types, encapsulations, topologies, and routing protocols BGP, EIGRP, IS-IS, and OSPF. By sending rapid failure detection notices to the routing protocols in the local router to initiate the routing table recalculation process, BFD contributes to greatly reduced overall network convergence time. The figure below shows a simple network with two routers running OSPF and BFD. When OSPF discovers a neighbor (1) it sends a request to the local BFD process to initiate a BFD neighbor session with the OSPF neighbor router (2). The BFD neighbor session with the OSPF neighbor router is established (3).

The figure below shows what happens when a failure occurs in the network (1). The BFD neighbor session with the OSPF neighbor router is torn down (2). BFD notifies the local OSPF process that the BFD neighbor is no longer reachable (3). The local OSPF process tears down the OSPF neighbor relationship (4). If an alternative path is available, the routers will immediately start converging on it.

A routing protocol needs to register with BFD for every neighbor it acquires. Once a neighbor is registered, BFD initiates a session with the neighbor if a session does not already exist.

OSPF registers with BFD when:

  • A neighbor finite state machine (FSM) transitions to full state.
  • Both OSPF BFD and BFD are enabled.

On broadcast interfaces, OSPF establishes a BFD session only with the designated router (DR) and backup designated router (BDR), but not between any two routers in DROTHER state.

BFD Detection of Failures

Once a BFD session has been established and timer negations are complete, BFD peers send BFD control packets that act in the same manner as an IGP hello protocol to detect liveliness, except at a more accelerated rate. The following information should be noted:

  • BFD is a forwarding path failure detection protocol. BFD detects a failure, but the routing protocol must take action to bypass a failed peer.
  • Typically, BFD can be used at any protocol layer. However, the Cisco implementation of BFD for Cisco IOS Releases 12.0(31)S, and 12.4(4)T supports only Layer 3 clients, in particular, the BGP, EIGRP, IS-IS, and OSPF routing protocols. For Cisco IOS Release 12.2(33)SRC, BFD is supported for static routing.
  • The Cisco implementation of BFD for Cisco IOS Release 12.2(18)SXE also supports only Layer 3 clients and the EIGRP, IS-IS, and OSPF routing protocols. It does not support the BGP routing protocol.
  • Cisco devices will use one BFD session for multiple client protocols in the Cisco implementation of BFD for Cisco IOS Releases 12.2(18)SXE, 12.0(31)S, and 12.4(4)T. For example, if a network is running OSPF and EIGRP across the same link to the same peer, only one BFD session will be established, and BFD will share session information with both routing protocols.

BFD Version Interoperability

Cisco IOS Release 12.4(9)T supports BFD Version 1 as well as BFD Version 0. All BFD sessions come up as Version 1 by default and will be interoperable with Version 0. The system automatically performs BFD version detection, and BFD sessions between neighbors will run in the highest common BFD version between neighbors. For example, if one BFD neighbor is running BFD Version 0 and the other BFD neighbor is running Version 1, the session will run BFD Version 0. The output from the show bfd neighbors [details] command will verify which BFD version a BFD neighbor is running.

See the Example Configuring BFD in an EIGRP Network with Echo Mode Enabled by Default for an example of BFD version detection.

BFD Support on Cisco 12000 Routers

The Cisco 12000 series routers support distributed BFD to take advantage of its distributed Route Processor (RP) and line card (LC) architecture. The BFD tasks will be divided and assigned to the BFD process on the RP and LC, as described in the following sections:

BFD Process on the RP
Client Interaction

The BFD process on the RP will handle the interaction with clients, which create and delete BFD sessions.

Session Management for the BFD Process on the RP

The BFD RP process will primarily own all BFD sessions on the router. It will pass the session creation and deletion requests to the BFD processes on all LCs. BFD LC sessions will have no knowledge of sessions being added or deleted by the clients. Only the BFD RP process will send session addition and deletion commands to the BFD LC process.

Session Database Management

The BFD RP process will maintain a database of all the BFD sessions on the router. This database will contain only the minimum required information.

Process EXEC Commands

The BFD RP process services the BFD show commands.

BFD Process on the LC
Session Management for the BFD Process on the LC

The BFD LC process manages sessions, adds and deletes commands from the BFD RP process, and creates and deletes new sessions based on the commands. In the event of transmit failure, receive failure, or session-down detection, the LC BFD instance will immediately notify the BFD RP process. It will also update transmit and receive counters. The BFD session is maintained completely on the LC. BFD control packets are received and processed, as well as sent, from the LC itself.

Session Database Management

The BFD LC process maintains a database of all the BFD sessions hosted on the LC.

Receive and Transmit

The BFD LC process is responsible for transmitting and receiving BFD packets for the sessions on the LC.

BFD Session Limits

In Cisco IOS Release 12.2(33)SRC, the number of BFD sessions that can be created has been increased to 128.

BFD Support for Nonbroadcast Media Interfaces

In Cisco IOS Release 12.2(33)SRC, the BFD feature is supported on nonbroadcast media interfaces including ATM, POS, serial, and VLAN interfaces. BFD support also extends to ATM, Frame Relay (FR), POS, and serial subinterfaces.

The bfd interval command must be configured on the interface to initiate BFD monitoring.

BFD Support for VPN Routing and Forwarding Interfaces

The BFD feature is extended in Cisco IOS Release 12.2(33)SRC to be VPN Routing and Forwarding (VRF) aware to provide fast detection of routing protocol failures between provider edge (PE) and customer edge (CE) routers.

BFD Support for Nonstop Forwarding with Stateful Switchover

Typically, when a networking device restarts, all routing peers of that device detect that the device went down and then came back up. This transition results in a routing flap, which could spread across multiple routing domains. Routing flaps caused by routing restarts create routing instabilities, which are detrimental to the overall network performance. Nonstop forwarding (NSF) helps to suppress routing flaps in devices that are enabled with stateful switchover (SSO), thereby reducing network instability.

NSF allows for the forwarding of data packets to continue along known routes while the routing protocol information is being restored after a switchover. With NSF, peer networking devices do not experience routing flaps. Data traffic is forwarded through intelligent line cards or dual forwarding processors while the standby RP assumes control from the failed active RP during a switchover. The ability of line cards and forwarding processors to remain up through a switchover and to be kept current with the Forwarding Information Base (FIB) on the active RP is key to NSF operation.

In devices that support dual RPs, SSO establishes one of the RPs as the active processor; the other RP is designated as the standby processor, and then synchronizes information between them. A switchover from the active to the standby processor occurs when the active RP fails, when it is removed from the networking device, or when it is manually taken down for maintenance.

In Cisco IOS Release 12.2(33)SRC, BFD sessions are placed in an “Admin Down” state during a planned switchover. The BFD configuration is synched from the active to standby processor, and all BFD clients re-register with the BFD process on the standby processor.

In Cisco IOS Release 12.2(33)SB, BFD is not SSO-aware, and it is not supported with NSF/SSO. These features should not be used together. Enabling BFD along with NSF/SSO causes the nonstop forwarding capability to break during failover because BFD adjacencies are not maintained and the routing clients are forced to mark down adjacencies and reconverge.

BFD Support for Stateful Switchover

The BFD protocol provides short-duration detection of failures in the path between adjacent forwarding engines. In network deployments that use dual RP routers or switches (to provide redundancy), the routers have a graceful restart mechanism that protects the forwarding state during a switchover between the active RP and the standby RP.

The dual RPs have variable switchover times that depend on the ability of the hardware to detect a communication failure. When BFD is running on the RP, some platforms are not able to detect a switchover before the BFD protocol times out; these platforms are referred to as slow switchover platforms.

Stateful BFD on the Standby RP

To ensure a successful switchover to the standby RP, the BFD protocol uses checkpoint messages to send session information from the active RP Cisco IOS instance to the standby RP Cisco IOS instance. The session information includes local and remote discriminators, adjacent router timer information, BFD setup information, and session-specific information such as the type of session and the session version. In addition, the BFD protocol sends session creation and deletion checkpoint messages to create or delete a session on the standby RP.

The BFD sessions on the standby RP do not receive or send packets and do not process expired timers. These sessions wait for a switchover to occur and then send packets for any active sessions so that sessions do not time out on adjacent routers.

When the BFD protocol on the standby RP is notified of a switchover it changes its state to active, registers itself with Cisco Express Forwarding so that it can receive packets, and then sends packets for any elements that have expired.

BFD also uses checkpoint messages to ensure that sessions created by clients on the active RP are maintained during a switchover. When a switchover occurs, BFD starts an SSO reclaim timer. Clients must reclaim their sessions within the duration specified by the reclaim timer or else the session is deleted.

Timer values are different based on the number of BFD sessions and the platform.

The table below describes the timer values on Cisco 7600 series routers.

Table 1 BFD Timer Values on a Cisco 7600 Series Router

Maximum Number of BFD Sessions

Chassis Type

BFD Session Type

Minimum Timer Value (ms)

Clients

Comments

128

S-chassis

Async/echo

500 multiplier 3

All

--

512

S-chassis

Async/echo

999 multiplier 3

All

--

128

Non-S-chassis

Async

999 multiplier 5

All

--

128

  • Non-S-chassis
  • DFC line card

Echo

999 multiplier 3

All

BFD slow timers configured to 5000

512

Non-S-Chassis

Async/echo

999 multiplier 5

All

--


Note


The BFD SSO feature is supported on Cisco 7600 series routers in Cisco IOS Release 12.2(33)SRE and later releases.



Note


For hardware offload to ES+ line cards on Cisco 7600 series routers in Cisco IOS Release 15.1(2)S, the Tx interval on both BFD peers must be configured in multiples of 50 ms. See the “Configuring Synchronous Ethernet on the Cisco 7600 Router with ES+ Line Card” section of the Cisco 7600 Series Ethernet Services Plus (ES+) and Ethernet Services Plus T (ES+T) Line Card Configuration Guide for more information about prerequisites for hardware offload.


The table below describes the timer values on Cisco ASR 1000 Series Aggregation Services Routers.

Table 2 BFD Timer Values on a Cisco ASR 1000 Series Aggregation Services Router

Maximum Number of BFD Sessions

Chassis Type

BFD Session Type

Minimum Timer Value (ms)

Clients

Comments

128

All

Async/echo

50 multiplier 3

All

--

512

All

Async/echo

999 multiplier 3

All

--


Note


The BFD SSO feature is supported on Cisco ASR 1000 Series Aggregation Services Routers in Cisco IOS Release 12.2(33)XNA and later releases.


The table below describes the timer values on Cisco 6500 series routers.

Table 3 BFD Timer Values on a Cisco 6500 Series Router

Maximum Number of BFD Sessions

Chassis Type

BFD Session Type

Minimum Timer Value (ms)

Clients

Comments

50

E-chassis/ 67xx line cards

Async/Echo

500 multiplier 3

All (except EIGRP)

CFC line cards are not supported

30

E-chassis/ 67xx line cards

Async/Echo

500 multiplier 3

EIGRP

CFC line cards are not supported


Note


The BFD SSO feature is supported on Cisco 6500 series routers in Cisco IOS Release 12.2(33)SXI2 and later releases.


The table below describes the timer values on a Cisco 10000 series routers.

Table 4 BFD Timer Values on a Cisco 10000 Series Router

Maximum Number of BFD Sessions

Chassis Type

BFD Session Type

Minimum Timer Value (ms)

Clients

Comments

1100

PRE3/PRE4

Async/echo

999 multiplier 5

All

--


Note


The BFD SSO feature is supported on Cisco 10000 series routers in Cisco IOS Release 12.2(33)XNE and later releases.


BFD Support for Static Routing

Unlike dynamic routing protocols, such as OSPF and BGP, static routing has no method of peer discovery. Therefore, when BFD is configured, the reachability of the gateway is completely dependent on the state of the BFD session to the specified neighbor. Unless the BFD session is up, the gateway for the static route is considered unreachable, and therefore the affected routes will not be installed in the appropriate Routing Information Base (RIB).

For a BFD session to be successfully established, BFD must be configured on the interface on the peer and there must be a BFD client registered on the peer for the address of the BFD neighbor. When an interface is used by dynamic routing protocols, the latter requirement is usually met by configuring the routing protocol instances on each neighbor for BFD. When an interface is used exclusively for static routing, this requirement must be met by configuring static routes on the peers.

If a BFD configuration is removed from the remote peer while the BFD session is in the up state, the updated state of the BFD session is not signaled to IPv4 static. This will cause the static route to remain in the RIB. The only workaround is to remove the IPv4 static BFD neighbor configuration so that the static route no longer tracks BFD session state. Also, if you change the encapsulation type on a serial interface to one that is unsupported by BFD, BFD will be in a down state on that interface. The workaround is to shut down the interface, change to a supported encapsulation type, and then reconfigure BFD.

A single BFD session can be used by an IPv4 static client to track the reachability of next hops through a specific interface. You can assign a BFD group for a set of BFD-tracked static routes. Each group must have one active static BFD configuration, one or more passive BFD configurations, and the corresponding static routes to be BFD-tracked. Nongroup entries are BFD-tracked static routes for which a BFD group is not assigned. A BFD group must accommodate static BFD configurations that can be part of different VRFs. Effectively, the passive static BFD configurations need not be in the same VRF as that of the active configuration.

For each BFD group, there can be only one active static BFD session. You can configure the active BFD session by adding a static BFD configuration and a corresponding static route that uses the BFD configuration. The BFD session in a group is created only when there is an active static BFD configuration and the static route that uses the static BFD configuration. When the active static BFD configuration or the active static route is removed from a BFD group, all the passive static routes are withdrawn from the RIB. Effectively, all the passive static routes are inactive until an active static BFD configuration and a static route to be tracked by the active BFD session are configured in the group.

Similarly, for each BFD group, there can be one or more passive static BFD configurations and their corresponding static routes to be BFD-tracked. Passive static session routes take effect only when the active BFD session state is reachable. Though the active BFD session state of the group is reachable, the passive static route is added to the RIB only if the corresponding interface state is up. When a passive BFD session is removed from a group, it will not affect the active BFD session if one existed, or the BFD group reachability status.

BFD Control Channel over VCCV Support for ATM Pseudowire

Multiprotocol Label Switching (MPLS) pseudowires enable L2 traffic to be carried over an IP/MPLS core network. The BFD control channel over VCCV--Support for ATM Pseudowires feature provides operations and management (OAM) functions for MPLS pseudowires.


Note


This feature provides support for VCCV type 1 only. VCCV Type 1 is in-band VCCV and can be used only for MPLS pseudowires that use a control word.


The BFD detection protocol can be used to provide OAM functionality to the MPLS protocol. VCCV provides a control channel associated with the pseudowire to provide OAM functions over that pseudowire. BFD can use the VCCV control channel as a pseudowire fault mechanism to detect dataplane failures. BFD can also use the VCCV control channel to carry the fault status of an attachment circuit (AC).

MPLS pseudowires can dynamically signal or statically configure virtual circuit (VC) labels. In dynamically signaled pseudowires, the control channel (CC) types and connection verification (CV) types are also signaled. In statically configured pseudowires, the CC and CV types must be configured on both ends of the pseudowire.

The CC types define whether VCCV packets are in-band or out-of-band for the pseudowire. The CV types define whether BFD monitoring is required for the pseudowire. If BFD monitoring is required for the pseudowire, the CV types also define how the BFD packets are encapsulated and whether BFD provides status signaling functionality.

Any protocol that requires BFD monitoring must register with BFD as a client. For example, the Xconnect protocol registers as a BFD client, and BFD assigns a client ID to Xconnect. Xconnect uses this client ID to create the BFD sessions that monitor the pseudowire.

BFD can detect forwarding failures (end-to-end) in the pseudowire path. When BFD detects a failure in the pseudowire forwarding path it notifies the Xconnect client that created the session. In addition, BFD can signal the status in any concatenated path, or AC, to the remote device where the BFD session is terminated.

The figure below shows a dynamically signaled MPLS pseudowire carrying an ATM payload. In this example, BFD monitoring of the pseudowire occurs from the Node B device to the PE device. BFD also monitors the signal status of the ACs between the PE and CE2 device, and between the Node B and CE1 device.

BFD on Multiple Hops

Cisco IOS Release 15.1(3)S and later releases support BFD on arbitrary paths, which might span multiple network hops. The BFD Multihop feature provides subsecond forwarding failure detection for a destination more than one hop, and up to 255 hops, away.

A BFD multihop session is set up between a unique source-destination address pair provided by the client. A session can be set up between two endpoints that have IP connectivity.

You must configure the bfd-template and bfd map commands to create a multihop template and associate it with one or more maps of destinations and associated BFD timers. You can enable authentication and configure a key chain for BFD multihop sessions.

Benefits of Using BFD for Failure Detection

When you deploy any feature, it is important to consider all the alternatives and be aware of any trade-offs being made.

The closest alternative to BFD in conventional EIGRP, IS-IS, and OSPF deployments is the use of modified failure detection mechanisms for EIGRP, IS-IS, and OSPF routing protocols.

If you set EIGRP hello and hold timers to their absolute minimums, the failure detection rate for EIGRP falls to within a one- to two-second range.

If you use fast hellos for either IS-IS or OSPF, these Interior Gateway Protocol (IGP) protocols reduce their failure detection mechanisms to a minimum of one second.

There are several advantages to implementing BFD over reduced timer mechanisms for routing protocols:

  • Although reducing the EIGRP, IS-IS, and OSPF timers can result in minimum detection timer of one to two seconds, BFD can provide failure detection in less than one second.
  • Because BFD is not tied to any particular routing protocol, it can be used as a generic and consistent failure detection mechanism for EIGRP, IS-IS, and OSPF.
  • Because some parts of BFD can be distributed to the data plane, it can be less CPU-intensive than the reduced EIGRP, IS-IS, and OSPF timers, which exist wholly at the control plane.

How to Configure Bidirectional Forwarding Detection

Configuring BFD Session Parameters on the Interface

The steps in this procedure show how to configure BFD on the interface by setting the baseline BFD session parameters on an interface. Repeat the steps in this procedure for each interface over which you want to run BFD sessions to BFD neighbors.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    interface type number

    4.    bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier

    5.    end


DETAILED STEPS
      Command or Action Purpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.
     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 interface type number


    Example:
    Router(config)# interface FastEthernet 6/0
     

    Enters interface configuration mode.

     
    Step 4 bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier


    Example:
    Router(config-if)# bfd interval 50 min_rx 50 multiplier 5
     

    Enables BFD on the interface.

     
    Step 5 end


    Example:
    Router(config-if)# end
     

    Exits interface configuration mode and returns to privileged EXEC mode.

     

    Configuring BFD Support for Dynamic Routing Protocols

    You can enable BFD support for dynamic routing protocols at the router level to enable BFD support globally for all interfaces or you can configure BFD on a per-interface basis at the interface level.

    For Cisco IOS Release 12.2(18)SXE, you may configure BFD support for one or more of the following routing protocols: EIGRP, IS-IS, and OSPF.

    For Cisco IOS Releases 12.2(33)SRA, you may configure BFD support for one or more of the following routing protocols: EIGRP, IS-IS, and OSPF.

    For Cisco IOS Releases 12.2(33)SRB, you may configure BFD support for one or more of the following routing protocols: BGP, EIGRP, IS-IS, and OSPF.

    For Cisco IOS Release 12.2(33)SRC, you may configure BFD support for static routing.

    For Cisco IOS Releases 12.0(31)S and 12.4(4)T, you may configure BFD support for one or more of the following routing protocols: BGP, IS-IS, and OSPF.

    For Cisco IOS Release 12.0(32)S, for the Cisco 10720 platform, you may configure BFD for one or more of the following routing protocols: BGP, IS-IS, and OSPF.

    For Cisco IOS Release 12.4(11)T, BFD support for HSRP was introduced.

    This section describes the following procedures:

    Configuring BFD Support for BGP

    This section describes the procedure for configuring BFD support for BGP so that BGP is a registered protocol with BFD and will receive forwarding path detection failure messages from BFD.

    Before You Begin

    BGP must be running on all participating routers.

    The baseline parameters for BFD sessions on the interfaces over which you want to run BFD sessions to BFD neighbors must be configured. See the Configuring BFD Session Parameters on the Interface section for more information.


    Note


    Output from the show bfd neighbors details command shows the configured intervals. The output does not show intervals that were changed because hardware-offloaded BFD sessions were configured with Tx and Rx intervals that are not multiples of 50 ms.


    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    router bgp as-tag

      4.    neighbor ip-address fall-over bfd

      5.    end

      6.    show bfd neighbors [details]

      7.    show ip bgp neighbor


    DETAILED STEPS
        Command or Action Purpose
      Step 1 enable


      Example:
      Router> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.
       
      Step 2 configure terminal


      Example:
      Router# configure terminal
       

      Enters global configuration mode.

       
      Step 3 router bgp as-tag


      Example:
      Router(config)# router bgp tag1
       

      Specifies a BGP process and enters router configuration mode.

       
      Step 4 neighbor ip-address fall-over bfd


      Example:
      Router(config-router)# neighbor 172.16.10.2 fall-over bfd
       

      Enables BFD support for fallover.

       
      Step 5 end


      Example:
      Router(config-router)# end
       

      Exits router configuration mode and returns the router to privileged EXEC mode.

       
      Step 6 show bfd neighbors [details]


      Example:
      Router# show bfd neighbors detail
       

      (Optional) Verifies that the BFD neighbor is active and displays the routing protocols that BFD has registered.

      Note   

      In order to display the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors details command when it is entered on a line card.

      Note   

      If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

       
      Step 7 show ip bgp neighbor


      Example:
      Router# show ip bgp neighbor
       

      (Optional) Displays information about BGP and TCP connections to neighbors.

       
      What to Do Next

      See the Monitoring and Troubleshooting BFD section for more information on monitoring and troubleshooting BFD. If you want to configure BFD support for another routing protocol, see the following sections.

      Configuring BFD Support for EIGRP

      This section describes the procedure for configuring BFD support for EIGRP so that EIGRP is a registered protocol with BFD and will receive forwarding path detection failure messages from BFD. There are two methods for enabling BFD support for EIGRP:

      • You can enable BFD for all of the interfaces for which EIGRP is routing by using the bfd all-interfaces command in router configuration mode.
      • You can enable BFD for a subset of the interfaces for which EIGRP is routing by using the bfd interface type number command in router configuration mode.
      Before You Begin

      EIGRP must be running on all participating routers.

      The baseline parameters for BFD sessions on the interfaces over which you want to run BFD sessions to BFD neighbors must be configured. See the Configuring BFD Session Parameters on the Interface section for more information.


      Note


      Output from the show bfd neighbors details command shows the configured intervals. The output does not show intervals that were changed because hardware-offloaded BFD sessions were configured with Tx and Rx intervals that are not multiples of 50 ms.



      Note


      BFD for EIGRP is not supported on the Cisco 12000 series routers for Cisco IOS Releases 12.0(31)S, 12.0(32)S, 12.4(4)T, and 12.2(33)SRA.


      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    router eigrp as-number

        4.    Do one of the following:

        • bfd all-interfaces
        • bfd interface type number

        5.    end

        6.    show bfd neighbors [details]

        7.    show ip eigrp interfaces [type number] [as-number] [detail]


      DETAILED STEPS
          Command or Action Purpose
        Step 1 enable


        Example:
        Router> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.
         
        Step 2 configure terminal


        Example:
        Router# configure terminal
         

        Enters global configuration mode.

         
        Step 3 router eigrp as-number


        Example:
        Router(config)# router eigrp 123
         

        Configures the EIGRP routing process and enters router configuration mode.

         
        Step 4 Do one of the following:
        • bfd all-interfaces
        • bfd interface type number


        Example:
        Router(config-router)# bfd all-interfaces


        Example:
        Router(config-router)# bfd interface FastEthernet 6/0
         

        Enables BFD globally on all interfaces associated with the EIGRP routing process.

        or

        Enables BFD on a per-interface basis for one or more interfaces associated with the EIGRP routing process.

         
        Step 5 end


        Example:
        Router(config-router) end
         

        Exits router configuration mode and returns the router to privileged EXEC mode.

         
        Step 6 show bfd neighbors [details]


        Example:
        Router# show bfd neighbors details
         

        (Optional) Verifies that the BFD neighbor is active and displays the routing protocols that BFD has registered.

        Note   

        In order to see the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors details command when it is entered on a line card.

        Note   

        If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

         
        Step 7 show ip eigrp interfaces [type number] [as-number] [detail]


        Example:
        Router# show ip eigrp interfaces detail
         

        (Optional) Displays the interfaces for which BFD support for EIGRP has been enabled.

         
        What to Do Next

        See the Monitoring andTroubleshooting BFD section for more information on monitoring and troubleshooting BFD. If you want to configure BFD support for another routing protocol, see the following sections.

        Configuring BFD Support for IS-IS

        This section describes the procedures for configuring BFD support for IS-IS so that IS-IS is a registered protocol with BFD and will receive forwarding path detection failure messages from BFD. There are two methods for enabling BFD support for IS-IS:

        • You can enable BFD for all of the interfaces on which IS-IS is supporting IPv4 routing by using the bfd all-interfaces command in router configuration mode. You can then disable BFD for one or more of those interfaces using the isis bfd disable command in interface configuration mode.
        • You can enable BFD for a subset of the interfaces for which IS-IS is routing by using the isis bfd command in interface configuration mode.

        To configure BFD support for IS-IS, perform the steps in one of the following sections:

        Prerequisites

        IS-IS must be running on all participating routers.

        The baseline parameters for BFD sessions on the interfaces that you want to run BFD sessions to BFD neighbors over must be configured. See the Configuring BFD Session Parameters on the Interface section for more information.


        Note


        Output from the show bfd neighbors details command shows the configured intervals. The output does not show intervals that were changed because hardware-offloaded BFD sessions were configured with Tx and Rx intervals that are not multiples of 50 ms.


        Configuring BFD Support for IS-IS for All Interfaces

        To configure BFD on all IS-IS interfaces that support IPv4 routing, perform the steps in this section.

        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    router isis area-tag

          4.    bfd all-interfaces

          5.    exit

          6.    interface type number

          7.    ip router isis [ tag ]

          8.    isis bfd [disable]

          9.    end

          10.    show bfd neighbors [details]

          11.    show clns interface


        DETAILED STEPS
            Command or Action Purpose
          Step 1 enable


          Example:
          Router> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.
           
          Step 2 configure terminal


          Example:
          Router# configure terminal
           

          Enters global configuration mode.

           
          Step 3 router isis area-tag


          Example:
          Router(config)# router isis tag1
           

          Specifies an IS-IS process and enters router configuration mode.

           
          Step 4 bfd all-interfaces


          Example:
          Router(config-router)# bfd all-interfaces
           

          Enables BFD globally on all interfaces associated with the IS-IS routing process.

           
          Step 5 exit


          Example:
          Router(config-router)# exit
           

          (Optional) Returns the router to global configuration mode.

           
          Step 6 interface type number


          Example:
          Router(config)# interface fastethernet 6/0
           

          (Optional) Enters interface configuration mode.

           
          Step 7 ip router isis [ tag ]


          Example:
          Router(config-if)# ip router isis tag1
           

          (Optional) Enables support for IPv4 routing on the interface.

           
          Step 8 isis bfd [disable]


          Example:
          Router(config-if)# isis bfd
           

          (Optional) Enables or disables BFD on a per-interface basis for one or more interfaces associated with the IS-IS routing process.

          Note   

          You should use the disable keyword only if you enabled BFD on all of the interfaces that IS-IS is associated with using the bfd all-interfaces command in router configuration mode.

           
          Step 9 end


          Example:
          Router(config-if)# end
           

          Exits interface configuration mode and returns the router to privileged EXEC mode.

           
          Step 10 show bfd neighbors [details]


          Example:
          Router# show bfd neighbors details
           

          (Optional) Displays information that can be used to verify if the BFD neighbor is active and displays the routing protocols that BFD has registered.

          Note   

          In order to display the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors details command when it is entered on a line card.

          Note   

          If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

           
          Step 11 show clns interface


          Example:
          Router# show clns interface
           

          (Optional) Displays information that can be used to verify if BFD for IS-IS has been enabled for a specific IS-IS interface that is associated.

           
          What to Do Next

          See the Monitoring and Troubleshooting BFD section for more information on monitoring and troubleshooting BFD. If you want to configure only for a specific subset of interfaces, perform the tasks in the Configuring BFD Support for IS-IS for One or More Interfaces section.

          Configuring BFD Support for IS-IS for One or More Interfaces

          To configure BFD for only one or more IS-IS interfaces, perform the steps in this section.


          Note


          Output from the show bfd neighbors details command shows the configured intervals. The output does not show intervals that were changed because hardware-offloaded BFD sessions were configured with Tx and Rx intervals that are not multiples of 50 ms.


          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    interface type number

            4.    ip router isis [ tag ]

            5.    isis bfd [disable]

            6.    end

            7.    show bfd neighbors [details]

            8.    show clns interface


          DETAILED STEPS
              Command or Action Purpose
            Step 1 enable


            Example:
            Router> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.
             
            Step 2 configure terminal


            Example:
            Router# configure terminal
             

            Enters global configuration mode.

             
            Step 3 interface type number


            Example:
            Router(config)# interface fastethernet 6/0
             

            Enters interface configuration mode.

             
            Step 4 ip router isis [ tag ]


            Example:
            Router(config-if)# ip router isis tag1
             

            Enables support for IPv4 routing on the interface.

             
            Step 5 isis bfd [disable]


            Example:
            Router(config-if)# isis bfd
             

            Enables or disables BFD on a per-interface basis for one or more interfaces associated with the IS-IS routing process.

            Note   

            You should use the disable keyword only if you enabled BFD on all of the interfaces that IS-IS is associated with using the bfd all-interfaces command in router configuration mode.

             
            Step 6 end


            Example:
            Router(config-if)# end
             

            Exits interface configuration mode and returns the router to privileged EXEC mode.

             
            Step 7 show bfd neighbors [details]


            Example:
            Router# show bfd neighbors details
             

            (Optional) Displays information that can help verify if the BFD neighbor is active and displays the routing protocols that BFD has registered.

            Note   

            In order to display the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors details command when it is entered on a line card.

            Note   

            If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

             
            Step 8 show clns interface


            Example:
            Router# show clns interface
             

            (Optional) Displays information that can help verify if BFD for IS-IS has been enabled for a specific IS-IS interface that is associated.

             
            What to Do Next

            See the Monitoring and Troubleshooting BFD section for more information on monitoring and maintaining BFD. If you want to configure BFD support for another routing protocol, see one of the following sections.

            Configuring BFD Support for OSPF

            This section describes the procedures for configuring BFD support for OSPF so that OSPF is a registered protocol with BFD and will receive forwarding path detection failure messages from BFD. You can either configure BFD support for OSPF globally on all interfaces or configure it selectively on one or more interfaces.

            There are two methods for enabling BFD support for OSPF:

            • You can enable BFD for all of the interfaces for which OSPF is routing by using the bfd all-interfaces command in router configuration mode. You can disable BFD support on individual interfaces using the ip ospf bfd [disable] command in interface configuration mode.
            • You can enable BFD for a subset of the interfaces for which OSPF is routing by using the ip ospf bfd command in interface configuration mode.

            See the following sections for tasks for configuring BFD support for OSPF:

            Configuring BFD Support for OSPF for All Interfaces

            To configure BFD for all OSPF interfaces, perform the steps in this section.

            If you do not want to configure BFD on all OSPF interfaces and would rather configure BFD support specifically for one or more interfaces, see the Configuring BFD Support for OSPF for One or More Interfaces section.

            Before You Begin

            OSPF must be running on all participating routers.

            The baseline parameters for BFD sessions on the interfaces over which you want to run BFD sessions to BFD neighbors must be configured. See the Configuring BFD Session Parameters on the Interface section for more information.


            Note


            Output from the show bfd neighbors details command shows the configured intervals. The output does not show intervals that were changed because hardware-offloaded BFD sessions were configured with Tx and Rx intervals that are not multiples of 50 ms.


            SUMMARY STEPS

              1.    enable

              2.    configure terminal

              3.    router ospf process-id

              4.    bfd all-interfaces

              5.    exit

              6.    interface type number

              7.    ip ospf bfd [disable]

              8.    end

              9.    show bfd neighbors [details]

              10.    show ip ospf


            DETAILED STEPS
                Command or Action Purpose
              Step 1 enable


              Example:
              Router> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.
               
              Step 2 configure terminal


              Example:
              Router# configure terminal
               

              Enters global configuration mode.

               
              Step 3 router ospf process-id


              Example:
              Router(config)# router ospf 4
               

              Specifies an OSPF process and enters router configuration mode.

               
              Step 4 bfd all-interfaces


              Example:
              Router(config-router)# bfd all-interfaces
               

              Enables BFD globally on all interfaces associated with the OSPF routing process.

               
              Step 5 exit


              Example:
              Router(config-router)# exit
               

              (Optional) Returns the router to global configuration mode. Enter this command only if you want to perform Step 7 to disable BFD for one or more interfaces.

               
              Step 6 interface type number


              Example:
              Router(config)# interface fastethernet 6/0
               

              (Optional) Enters interface configuration mode. Enter this command only if you want to perform Step 7 to disable BFD for one or more interfaces.

               
              Step 7 ip ospf bfd [disable]


              Example:
              Router(config-if)# ip ospf bfd disable
               

              (Optional) Disables BFD on a per-interface basis for one or more interfaces associated with the OSPF routing process.

              Note   

              You should use the disable keyword only if you enabled BFD on all of the interfaces that OSPF is associated with using the bfd all-interfaces command in router configuration mode.

               
              Step 8 end


              Example:
              Router(config-if)# end
               

              Exits interface configuration mode and returns the router to privileged EXEC mode.

               
              Step 9 show bfd neighbors [details]


              Example:
              Router# show bfd neighbors detail
               

              (Optional) Displays information that can help verify if the BFD neighbor is active and displays the routing protocols that BFD has registered.

              Note   

              In order to display the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors detailscommandwhen it is entered on a line card.

              Note   

              If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

               
              Step 10 show ip ospf


              Example:
              Router# show ip ospf
               

              (Optional) Displays information that can help verify if BFD for OSPF has been enabled.

               
              What to Do Next

              See the Monitoring and Troubleshooting BFD section for more information on monitoring and troubleshooting BFD. If you want to configure BFD support for another routing protocol, see the following sections.

              Configuring BFD Support for OSPF for One or More Interfaces

              To configure BFD on one or more OSPF interfaces, perform the steps in this section.

              Before You Begin

              OSPF must be running on all participating routers.

              The baseline parameters for BFD sessions on the interfaces over which you want to run BFD sessions to BFD neighbors must be configured. See the Configuring BFD Session Parameters on the Interface section for more information.


              Note


              Output from the show bfd neighbors details command shows the configured intervals. The output does not show intervals that were changed because hardware-offloaded BFD sessions were configured with Tx and Rx intervals that are not multiples of 50 ms.


              SUMMARY STEPS

                1.    enable

                2.    configure terminal

                3.    interface type number

                4.    ip ospf bfd [disable]

                5.    end

                6.    show bfd neighbors [details]

                7.    show ip ospf


              DETAILED STEPS
                  Command or Action Purpose
                Step 1 enable


                Example:
                Router> enable
                 

                Enables privileged EXEC mode.

                • Enter your password if prompted.
                 
                Step 2 configure terminal


                Example:
                Router# configure terminal
                 

                Enters global configuration mode.

                 
                Step 3 interface type number


                Example:
                Router(config)# interface fastethernet 6/0
                 

                Enters interface configuration mode.

                 
                Step 4 ip ospf bfd [disable]


                Example:
                Router(config-if)# ip ospf bfd
                 

                Enables or disables BFD on a per-interface basis for one or more interfaces associated with the OSPF routing process.

                Note   

                You should use the disable keyword only if you enabled BFD on all of the interfaces that OSPF is associated with using the bfd all-interfaces command in router configuration mode.

                 
                Step 5 end


                Example:
                Router(config-if)# end
                 

                Exits interface configuration mode and returns the router to privileged EXEC mode.

                 
                Step 6 show bfd neighbors [details]


                Example:
                Router# show bfd neighbors details
                 

                (Optional) Displays information that can help verify if the BFD neighbor is active and displays the routing protocols that BFD has registered.

                Note   

                In order to display the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors details command when it is entered on a line card.

                Note   

                If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

                 
                Step 7 show ip ospf


                Example:
                Router# show ip ospf
                 

                (Optional) Displays information that can help verify if BFD support for OSPF has been enabled.

                 
                What to Do Next

                See the Monitoring and Troubleshooting BFD section for more information on monitoring and troubleshooting BFD. If you want to configure BFD support for another routing protocol, see the following sections.

                Configuring BFD Support for HSRP

                Perform this task to enable BFD support for Hot Standby Router Protocol (HSRP.) Repeat the steps in this procedure for each interface over which you want to run BFD sessions to HSRP peers.

                HSRP supports BFD by default. If HSRP support for BFD has been manually disabled, you can reenable it at the router level to enable BFD support globally for all interfaces or on a per-interface basis at the interface level.

                Before You Begin
                • HSRP must be running on all participating routers.
                • Cisco Express Forwarding must be enabled.
                SUMMARY STEPS

                  1.    enable

                  2.    configure terminal

                  3.    ip cef [distributed]

                  4.    interface type number

                  5.    ip address ip-address mask

                  6.    standby [group-number] ip [ip-address [secondary]]

                  7.    standby bfd

                  8.    exit

                  9.    standby bfd all-interfaces

                  10.    exit

                  11.    show standby neighbors


                DETAILED STEPS
                    Command or Action Purpose
                  Step 1 enable


                  Example:
                  Router> enable
                   

                  Enables privileged EXEC mode.

                  • Enter your password if prompted.
                   
                  Step 2 configure terminal


                  Example:
                  Router# configure terminal
                   

                  Enters global configuration mode.

                   
                  Step 3 ip cef [distributed]


                  Example:
                  Router(config)# ip cef
                   

                  Enables Cisco Express Forwarding or distributed Cisco Express Forwarding.

                   
                  Step 4 interface type number


                  Example:
                  Router(config)# interface FastEthernet 6/0
                   

                  Enters interface configuration mode.

                   
                  Step 5 ip address ip-address mask


                  Example:
                  Router(config-if)# ip address 10.0.0.11 255.255.255.0
                   

                  Configures an IP address for the interface.

                   
                  Step 6 standby [group-number] ip [ip-address [secondary]]


                  Example:
                  Router(config-if)# standby 1 ip 10.0.0.11
                   

                  Activates HSRP.

                   
                  Step 7 standby bfd


                  Example:
                  Router(config-if)# standby bfd
                   

                  (Optional) Enables HSRP support for BFD on the interface.

                   
                  Step 8 exit


                  Example:
                  Router(config-if)# exit
                   

                  Exits interface configuration mode.

                   
                  Step 9 standby bfd all-interfaces


                  Example:
                  Router(config)# standby bfd all-interfaces
                   

                  (Optional) Enables HSRP support for BFD on all interfaces.

                   
                  Step 10 exit


                  Example:
                  Router(config)# exit
                   

                  Exits global configuration mode.

                   
                  Step 11 show standby neighbors


                  Example:
                  Router# show standby neighbors
                   

                  (Optional) Displays information about HSRP support for BFD.

                   
                  What to Do Next

                  See the Monitoring and Troubleshooting BFD section for more information on monitoring and troubleshooting BFD. If you want to configure BFD support for another routing protocol, see the following sections.

                  Configuring BFD Support for Static Routing

                  Perform this task to configure BFD support for static routing. Repeat the steps in this procedure on each BFD neighbor. For more information, see the "Example: Configuring BFD Support for Static Routing" section.

                  SUMMARY STEPS

                    1.    enable

                    2.    configure terminal

                    3.    interface type number

                    4.    ip address ip-address mask

                    5.    bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier

                    6.    exit

                    7.    ip route static bfd interface-type interface-number ip-address [ group group-name [ passive ]]

                    8.    ip route [ vrf vrf-name ] prefix mask {ip-address | interface-type interface-number [ip-address]} [dhcp] [distance] [name next-hop-name] [permanent | track number] [tag tag]

                    9.    exit

                    10.    show ip static route

                    11.    show ip static route bfd

                    12.    exit


                  DETAILED STEPS
                      Command or Action Purpose
                    Step 1 enable


                    Example:
                    Router> enable
                     

                    Enables privileged EXEC mode.

                    • Enter your password if prompted.
                     
                    Step 2 configure terminal


                    Example:
                    Router# configure terminal
                     

                    Enters global configuration mode.

                     
                    Step 3 interface type number


                    Example:
                    Router(config)# interface serial 2/0
                     

                    Configures an interface and enters interface configuration mode.

                     
                    Step 4 ip address ip-address mask


                    Example:
                    Router(config-if)# ip address 10.201.201.1 255.255.255.0
                     

                    Configures an IP address for the interface.

                     
                    Step 5 bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier


                    Example:
                    Router(config-if)# bfd interval 500 min_rx 500 multiplier 5
                     

                    Enables BFD on the interface.

                     
                    Step 6 exit


                    Example:
                    Router(config-if)# exit
                     

                    Exits interface configuration mode and returns to global configuration mode.

                     
                    Step 7 ip route static bfd interface-type interface-number ip-address [ group group-name [ passive ]]


                    Example:
                    Router(config)# ip route static bfd serial 2/0 10.1.1.1 group group1 passive 
                     

                    Specifies a static route BFD neighbor.

                    • The interface-type, interface-number, and ip-address arguments are required because BFD support exists only for directly connected neighbors.
                     
                    Step 8 ip route [ vrf vrf-name ] prefix mask {ip-address | interface-type interface-number [ip-address]} [dhcp] [distance] [name next-hop-name] [permanent | track number] [tag tag]


                    Example:
                    Router(config)# ip route 10.0.0.0 255.0.0.0 
                     

                    Specifies a static route BFD neighbor.

                     
                    Step 9 exit


                    Example:
                    Router(config)# exit
                     

                    Exits global configuration mode and returns to privileged EXEC mode.

                     
                    Step 10 show ip static route


                    Example:
                    Router# show ip static route
                     

                    (Optional) Displays static route database information.

                     
                    Step 11 show ip static route bfd


                    Example:
                    Router# show ip static route bfd 
                     

                    (Optional) Displays information about the static BFD configuration from the configured BFD groups and nongroup entries.

                     
                    Step 12 exit


                    Example:
                    Router# exit
                     

                    Exits privileged EXEC mode and returns to user EXEC mode.

                     

                    Configuring BFD Echo Mode

                    BFD echo mode is enabled by default, but you can disable it such that it can run independently in each direction.

                    BFD echo mode works with asynchronous BFD. Echo packets are sent by the forwarding engine and forwarded back along the same path in order to perform detection--the BFD session at the other end does not participate in the actual forwarding of the echo packets. The echo function and the forwarding engine are responsible for the detection process; therefore, the number of BFD control packets that are sent out between two BFD neighbors is reduced. In addition, because the forwarding engine is testing the forwarding path on the remote (neighbor) system without involving the remote system, there is an opportunity to improve the interpacket delay variance, thereby achieving quicker failure detection times than when using BFD Version 0 with BFD control packets for the BFD session.

                    Echo mode is described as without asymmetry when it is running on both sides (both BFD neighbors are running echo mode).

                    Prerequisites

                    BFD must be running on all participating routers.

                    Before using BFD echo mode, you must disable the sending of Internet Control Message Protocol (ICMP) redirect messages by entering the no ip redirects command, in order to avoid high CPU utilization.

                    The baseline parameters for BFD sessions on the interfaces over which you want to run BFD sessions to BFD neighbors must be configured. See the Configuring BFD Session Parameters on the Interface section for more information.

                    Restrictions

                    BFD echo mode, which is supported in BFD Version 1, is available only in Cisco IOS Releases 12.4(9), and 12.2(33)SRA.


                    Note


                    BFD echo mode does not work in conjunction with Unicast Reverse Path Forwarding (uRPF) configuration. If BFD echo mode and uRPF configurations are enabled, then the sessions will flap.


                    Configuring the BFD Slow Timer

                    The steps in this procedure show how to change the value of the BFD slow timer. Repeat the steps in this procedure for each BFD router.

                    SUMMARY STEPS

                      1.    enable

                      2.    configure terminal

                      3.    bfd slow-timer milliseconds

                      4.    end


                    DETAILED STEPS
                        Command or Action Purpose
                      Step 1 enable


                      Example:
                      Router> enable
                       

                      Enables privileged EXEC mode.

                      • Enter your password if prompted.
                       
                      Step 2 configure terminal


                      Example:
                      Router# configure terminal
                       

                      Enters global configuration mode.

                       
                      Step 3 bfd slow-timer milliseconds


                      Example:
                      Router(config)# bfd slow-timer 12000
                       

                      Configures the BFD slow timer.

                       
                      Step 4 end


                      Example:
                      Router(config)# end
                       

                      Exits global configuration mode and returns the router to privileged EXEC mode.

                       

                      Disabling BFD Echo Mode Without Asymmetry

                      The steps in this procedure show how to disable BFD echo mode without asymmetry—no echo packets will be sent by the router, and the router will not forward BFD echo packets that are received from any neighbor routers.

                      Repeat the steps in this procedure for each BFD router.

                      SUMMARY STEPS

                        1.    enable

                        2.    configure terminal

                        3.    no bfd echo

                        4.    end


                      DETAILED STEPS
                          Command or Action Purpose
                        Step 1 enable


                        Example:
                        Router> enable
                         

                        Enables privileged EXEC mode.

                        • Enter your password if prompted.
                         
                        Step 2 configure terminal


                        Example:
                        Router# configure terminal
                         

                        Enters global configuration mode.

                         
                        Step 3 no bfd echo


                        Example:
                        Router(config)# no bfd echo
                         

                        Disables BFD echo mode.

                        • Use the no form to disable BFD echo mode.
                         
                        Step 4 end


                        Example:
                        Router(config)# end
                         

                        Exits global configuration mode and returns to privileged EXEC mode.

                         

                        Creating and Configuring BFD Templates

                        You can configure a single-hop template to specify a set of BFD interval values. BFD interval values specified as part of the BFD template are not specific to a single interface. You can configure a multihop template to associate these values with one or more maps of destinations and associated BFD timers. You can enable authentication and configure a key chain for BFD multihop sessions.

                        Configuring a Single-Hop Template

                        Perform this task to create a BFD single-hop template and configure BFD interval timers.


                        Note


                        Cisco IOS Release 15.0(1)S introduced the concept of BFD templates that allow BFD interval timers to be configured independently of an interface. BFD templates are required to provide support for the BFD Control Channel over VCCV-Support for ATM Pseudowires feature.


                        SUMMARY STEPS

                          1.    enable

                          2.    configure terminal

                          3.    bfd-template single-hop template-name

                          4.    interval min-tx milliseconds min-rx milliseconds multiplier multiplier-value

                          5.    end


                        DETAILED STEPS
                            Command or Action Purpose
                          Step 1 enable


                          Example:
                          Router> enable
                           

                          Enables privileged EXEC mode.

                          • Enter your password if prompted.
                           
                          Step 2 configure terminal


                          Example:
                          Router# configure terminal
                           

                          Enters global configuration mode.

                           
                          Step 3 bfd-template single-hop template-name


                          Example:
                          Router(config)# bfd-template single-hop bfdtemplate1
                           

                          Creates a single-hop BFD template and enters BFD configuration mode.

                           
                          Step 4 interval min-tx milliseconds min-rx milliseconds multiplier multiplier-value


                          Example:
                          Router(bfd-config)# interval min-tx 120 min-rx 100 multiplier 3
                          
                           

                          Configures the transmit and receive intervals between BFD packets, and specifies the number of consecutive BFD control packets that must be missed before BFD declares that a peer is unavailable.

                           
                          Step 5 end


                          Example:
                          Router(bfd-config)# end
                           

                          Exits BFD configuration mode and returns the router to privileged EXEC mode.

                           

                          Configuring a Multihop Template

                          Perform this task to create a BFD multohop template and configure BFD interval timers, authentication, and key chain.


                          Note


                          Cisco IOS Release 15.1(3)S and later releases support BFD on multiple network hops. After you have configured interval timers and authentication in a template, you can configure a map to associate the template with unique source-destination address pairs for multihop BFD sessions.



                          Note


                          See “Xconnect as a Client of BFD” for information on configuring xconnect as a client of BFD and detecting failure with the monitor peer bfd command.


                          SUMMARY STEPS

                            1.    enable

                            2.    configure terminal

                            3.    bfd-template multi-hop template-name

                            4.    interval min-tx milliseconds min-rx milliseconds multiplier multiplier-value

                            5.    authentication authentication-type keychain keychain-name

                            6.    end


                          DETAILED STEPS
                              Command or Action Purpose
                            Step 1 enable


                            Example:
                            Router> enable
                             

                            Enables privileged EXEC mode.

                            • Enter your password if prompted.
                             
                            Step 2 configure terminal


                            Example:
                            Router# configure terminal
                             

                            Enters global configuration mode.

                             
                            Step 3 bfd-template multi-hop template-name


                            Example:
                            Router(config)# bfd-template multi-hop mh-template1
                             

                            Creates a BFD multihop BFD template and enters BFD configuration mode.

                             
                            Step 4 interval min-tx milliseconds min-rx milliseconds multiplier multiplier-value


                            Example:
                            Router(bfd-config)# interval min-tx 120 min-rx 100 multiplier 3
                            
                             

                            Configures the transmit and receive intervals between BFD packets, and specifies the number of consecutive BFD control packets that must be missed before BFD declares that a peer is unavailable.

                             
                            Step 5 authentication authentication-type keychain keychain-name


                            Example:
                            Router(bfd-config)# authentication keyed-sha-1 keychain bfd-multihop 
                            
                             

                            Configures authentication for the multihop template and specifies the authentication type.

                             
                            Step 6 end


                            Example:
                            Router(bfd-config)# end
                             

                            Exits BFD configuration mode and returns the router to privileged EXEC mode.

                             

                            What to Do Next

                            The BFD templates that you create can be applied to pseudowire classes to enable BFD control channel over VCCV on ATM pseudowire networks. For more information, see the Configuring BFD Control Channel over VCCV Support for ATM Pseudowire section.

                            Configuring a BFD Map

                            Perform this task to configure a BFD map that associates the interval timers and authentication configured in a template with unique source-destination address pairs for multihop BFD sessions.

                            Before You Begin

                            You must configure a BFD multihop template before you associate it with a map.

                            SUMMARY STEPS

                              1.    enable

                              2.    configure terminal

                              3.    bfd mapipv4 vrf vrf-name destination length source-address length template-name

                              4.    end


                            DETAILED STEPS
                                Command or Action Purpose
                              Step 1 enable


                              Example:
                              Router> enable
                               

                              Enables privileged EXEC mode.

                              • Enter your password if prompted.
                               
                              Step 2 configure terminal


                              Example:
                              Router# configure terminal
                               

                              Enters global configuration mode.

                               
                              Step 3 bfd mapipv4 vrf vrf-name destination length source-address length template-name


                              Example:
                              Router(config)# bfd map ipv4 vrf vpn1 192.168.0.0/24 192.168.42.5/32 mh-template1
                               

                              Configures a BFD map and associates it with the template.

                               
                              Step 4 end


                              Example:
                              Router(config)# end
                               

                              Exits BFD configuration mode and returns the router to privileged EXEC mode.

                               

                              Configuring BFD Control Channel over VCCV Support for ATM Pseudowire

                              Perform this task to configure BFD over VCCV Support for ATM Pseudowire networks.

                              Before You Begin

                              You must create and configure the BFD template before you assign it to the pseudowire class. For more information, see the Creating and Configuring BFD Templates section.

                              Before VCCV BFD can be run on pseudowires, pseudowires must be configured on the network.

                              SUMMARY STEPS

                                1.    enable

                                2.    configure terminal

                                3.    pseudowire-class name

                                4.    encapsulation type

                                5.    protoco l {ldp | none}

                                6.    vccv {control-word | router-alert | ttl}

                                7.    vccv bfd template name {udp | raw-bfd}

                                8.    vccv bfd status signaling

                                9.    exit

                                10.    interface atm interface-number

                                11.    atm asynchronous

                                12.    pvc vpi/ vci l2transport

                                13.    xconnect peer-ip-address vc-id {encapsulation mpls [manual] | pw-class pw-class-name} [pw-class pw-class-name] [sequencing {transmit | receive | both}]

                                14.    end


                              DETAILED STEPS
                                  Command or Action Purpose
                                Step 1 enable


                                Example:
                                Router> enable
                                 

                                Enables privileged EXEC mode.

                                • Enter your password if prompted.
                                 
                                Step 2 configure terminal


                                Example:
                                Router# configure terminal
                                 

                                Enters global configuration mode.

                                 
                                Step 3 pseudowire-class name


                                Example:
                                Router(config)# pseudowire-class vccv-bfd1
                                 

                                Specifies the name of the pseudowire class and enters pseudowire class configuration mode.

                                 
                                Step 4 encapsulation type


                                Example:
                                Router(config-pw-class)# encapsulation mpls
                                 

                                Specifies that MPLS is used as the data encapsulation method for tunneling Layer 2 traffic over the pseudowire.

                                • You must specify mpls encapsulation as part of the xconnect command or as part of a pseudowire class for the AToM Virtual Circuits to work properly.
                                 
                                Step 5 protoco l {ldp | none}


                                Example:
                                Router(config-pw-class)# protocol none
                                 

                                Specifies that no signaling is configured and that manually configured sessions are used.

                                • To configure static pseudowires, you must specify the none keyword.
                                 
                                Step 6 vccv {control-word | router-alert | ttl}


                                Example:
                                Router(config-pw-class)# vccv control-word
                                 

                                Sets the MPLS pseudowire CC type.

                                • For MPLS pseudowires that use a CV type that does not include IP/UDP headers, you must set the CC type to CC type 1: pseudowire control word.
                                 
                                Step 7 vccv bfd template name {udp | raw-bfd}


                                Example:
                                Router(config-pw-class)# vccv bfd template bfdtemplate1 raw-bfd
                                 

                                Enables VCCV BFD for the pseudowire class.

                                 
                                Step 8 vccv bfd status signaling


                                Example:
                                Router(config-pw-class)# vccv bfd status signaling
                                 

                                Enables status signaling for BFD VCCV.

                                 
                                Step 9 exit


                                Example:
                                Router(config-pw-class)# exit
                                 

                                Exits pseudowire class configuration mode and returns to global configuration mode.

                                 
                                Step 10 interface atm interface-number


                                Example:
                                Router(config)# interface atm 9/0/0
                                 

                                Configures an ATM interface and enters interface configuration mode

                                 
                                Step 11 atm asynchronous


                                Example:
                                Router(config-if)# atm asynchronous
                                 

                                Enables asynchronous mode on the ATM interface.

                                 
                                Step 12 pvc vpi/ vci l2transport


                                Example:
                                Router(config-if)# pvc 0/100 l2transport
                                 

                                Creates the ATM permanent virtual circuit (PVC), specifies the encapsulation type on an ATM PVC, and enters ATM virtual circuit configuration mode.

                                 
                                Step 13 xconnect peer-ip-address vc-id {encapsulation mpls [manual] | pw-class pw-class-name} [pw-class pw-class-name] [sequencing {transmit | receive | both}]


                                Example:
                                Router(cfg-if-atm-l2trans-pvc)# xconnect 10.0.0.7 100 pw-class vccv-bfd1
                                 

                                Binds an attachment circuit to a pseudowire, configures an AToM static pseudowire, and specifies the pseudowire class.

                                 
                                Step 14 end


                                Example:
                                Router(cfg-if-atm-l2trans-pvc)# end
                                 

                                Exits ATM virtual circuit configuration mode and returns to global configuration mode.

                                 

                                Monitoring and Troubleshooting BFD

                                This section describes how to retrieve BFD information for maintenance and troubleshooting. The commands in these tasks can be entered as needed, in any order desired.

                                For more information about BFD session initiation and failure, refer to the BFD Operation.

                                This section contains information for monitoring and troubleshooting BFD for the following Cisco platforms:

                                Monitoring and Troubleshooting BFD for Cisco 7600 Series Routers

                                To monitor or troubleshoot BFD on Cisco 7600 series routers, perform one or more of the steps in this section.


                                Note


                                See the “Configuring Synchronous Ethernet on the Cisco 7600 Router with ES+ Line Card” section of the Cisco 7600 Series Ethernet Services Plus (ES+) and Ethernet Services Plus T (ES+T) Line Card Configuration Guide for more information about troubleshooting BFD on Cisco 7600 series routers.


                                SUMMARY STEPS

                                  1.    enable

                                  2.    show bfd neighbors [details]

                                  3.    debug bfd [packet | event]


                                DETAILED STEPS
                                    Command or Action Purpose
                                  Step 1 enable


                                  Example:
                                  Router> enable
                                   

                                  Enables privileged EXEC mode.

                                  • Enter your password if prompted.
                                   
                                  Step 2 show bfd neighbors [details]


                                  Example:
                                  Router# show bfd neighbors details
                                   

                                  (Optional) Displays the BFD adjacency database.

                                  • The details keyword shows all BFD protocol parameters and timers per neighbor.
                                  Note   

                                  In order to see the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card. The registered protocols are not shown in the output of the show bfd neighbors details command when it is entered on a line card.

                                  Note   

                                  If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

                                   
                                  Step 3 debug bfd [packet | event]


                                  Example:
                                  Router# debug bfd packet
                                   

                                  (Optional) Displays debugging information about BFD packets.

                                   

                                  Monitoring and Troubleshooting BFD for Cisco 10720 Internet Routers

                                  To monitor or troubleshoot BFD on Cisco 10720 Internet routers, perform one or more of the steps in this section.

                                  SUMMARY STEPS

                                    1.    enable

                                    2.    show bfd neighbors [details]

                                    3.    debug bfd event

                                    4.    debug bfd packet


                                  DETAILED STEPS
                                      Command or Action Purpose
                                    Step 1 enable


                                    Example:
                                    Router> enable
                                     

                                    Enables privileged EXEC mode.

                                    • Enter your password if prompted.
                                     
                                    Step 2 show bfd neighbors [details]


                                    Example:
                                    Router# show bfd neighbors details
                                     

                                    (Optional) Displays the BFD adjacency database.

                                    • The details keyword will show all BFD protocol parameters and timers per neighbor.
                                    Note   

                                    The registered protocols are not shown in the output of the show bfd neighbors details when it is entered on a line card.

                                     
                                    Step 3 debug bfd event


                                    Example:
                                    Router# debug bfd event
                                     

                                    (Optional) Displays debugging information about BFD state transitions.

                                     
                                    Step 4 debug bfd packet


                                    Example:
                                    Router# debug bfd packet
                                     

                                    (Optional) Displays debugging information about BFD control packets.

                                     

                                    Monitoring and Troubleshooting BFD for Cisco 12000 Series Routers

                                    To monitor or troubleshoot BFD on Cisco 12000 series routers, perform one or more of the steps in this section.

                                    SUMMARY STEPS

                                      1.    enable

                                      2.    attach slot-number

                                      3.    show bfd neighbors [details]

                                      4.    show monitor event-trace bfd [all]

                                      5.    debug bfd event

                                      6.    debug bfd packet

                                      7.    debug bfd ipc-error

                                      8.    debug bfd ipc-event

                                      9.    debug bfd oir-error

                                      10.    debug bfd oir-event


                                    DETAILED STEPS
                                        Command or Action Purpose
                                      Step 1 enable


                                      Example:
                                      Router> enable
                                       

                                      Enables privileged EXEC mode.

                                      • Enter your password if prompted.
                                       
                                      Step 2 attach slot-number


                                      Example:
                                      Router# attach 6
                                       

                                      Connects you to a specific line card for the purpose of executing monitoring and maintenance commands on the specified line card. Slot numbers range from 0 to 11 for the Cisco 12012 and from 0 to 7 for the Cisco 12008.

                                      • If the slot number is omitted, you are prompted for the slot number.
                                      Note   

                                      In order to display the full output of the show bfd neighbors details command on a Cisco 12000 series router, you must enter the command on the line card. Enter the attach slot-number command to establish a CLI session with a line card.

                                       
                                      Step 3 show bfd neighbors [details]


                                      Example:
                                      Router# show bfd neighbors details
                                       

                                      Displays the BFD adjacency database.

                                      • The details keyword shows all BFD protocol parameters and timers per neighbor.
                                      Note   

                                      The registered protocols are not shown in the output of the show bfd neighbors details when it is entered on a line card.

                                      Note   

                                      If hardware-offloaded BFD sessions are configured with Tx and Rx intervals that are not multiples of 50 ms, the hardware intervals are changed. However, output from the show bfd neighbors details command will show the configured intervals, not the changed ones.

                                       
                                      Step 4 show monitor event-trace bfd [all]


                                      Example:
                                      Router# show monitor event-trace bfd all
                                       

                                      Displays logged messages for important events in “recent past” on BFD activities that occur on the line cards. This is a rolling buffer based log, so “distant past” events would be lost. Depending on traffic and frequency of events, these events could be seen over a variable time window.

                                       
                                      Step 5 debug bfd event


                                      Example:
                                      Router# debug bfd event
                                       

                                      Displays debugging information about BFD state transitions.

                                       
                                      Step 6 debug bfd packet


                                      Example:
                                      Router# debug bfd packet
                                       

                                      Displays debugging information about BFD control packets.

                                       
                                      Step 7 debug bfd ipc-error


                                      Example:
                                      Router# debug bfd ipc-error
                                       

                                      Displays debugging information with IPC errors on the RP and LC.

                                       
                                      Step 8 debug bfd ipc-event


                                      Example:
                                      Router# debug bfd ipc-event
                                       

                                      Displays debugging information with IPC events on the RP and LC.

                                       
                                      Step 9 debug bfd oir-error


                                      Example:
                                      Router# debug bfd oir-error
                                       

                                      Displays debugging information with OIR errors on the RP and LC.

                                       
                                      Step 10 debug bfd oir-event


                                      Example:
                                      Router# debug bfd oir-event
                                       

                                      Displays debugging information with OIR events on the RP and LC.

                                       

                                      Configuration Examples for Bidirectional Forwarding Detection

                                      Example: Configuring BFD in an EIGRP Network with Echo Mode Enabled by Default

                                      The following example shows how to configure BFD in an EIGRP network with echo mode enabled by default in Cisco IOS Release 12.4(9)T. In the following example, the EIGRP network contains RouterA, RouterB, and RouterC. Fast Ethernet interface 1/0 on RouterA is connected to the same network as Fast Ethernet interface 1/0 on Router B. Fast Ethernet interface 1/0 on RouterB is connected to the same network as Fast Ethernet interface 1/0 on RouterC.

                                      RouterA and RouterB are running BFD Version 1, which supports echo mode, and RouterC is running BFD Version 0, which does not support echo mode. The BFD sessions between RouterC and its BFD neighbors are said to be running echo mode with asymmetry because echo mode will run on the forwarding path for RouteA and RouterB, and their echo packets will return along the same path for BFD sessions and failure detections, while their BFD neighbor RouterC runs BFD Version 0 and uses BFD controls packets for BFD sessions and failure detections.

                                      The figure below shows a large EIGRP network with several routers, three of which are BFD neighbors that are running EIGRP as their routing protocol.

                                      The example, starting in global configuration mode, shows the configuration of BFD.

                                      Configuration for RouterA

                                      interface Fast Ethernet0/0
                                       no shutdown 
                                       ip address 10.4.9.14 255.255.255.0
                                       duplex auto
                                       speed auto
                                      !
                                      interface Fast Ethernet1/0
                                       ip address 172.16.1.1 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3 
                                       no shutdown
                                       duplex auto
                                       speed auto
                                      !
                                      router eigrp 11
                                       network 172.16.0.0
                                       bfd all-interfaces
                                       auto-summary
                                      !
                                      ip default-gateway 10.4.9.1
                                      ip default-network 0.0.0.0
                                      ip route 0.0.0.0 0.0.0.0 10.4.9.1
                                      ip route 172.16.1.129 255.255.255.255 10.4.9.1
                                      !
                                      no ip http server
                                      !
                                      logging alarm informational
                                      !
                                      control-plane
                                      !
                                      line con 0
                                       exec-timeout 30 0
                                       stopbits 1
                                      line aux 0
                                       stopbits 1
                                      line vty 0 4
                                       login
                                      !
                                      !
                                      end

                                      Configuration for RouterB

                                      !
                                      interface Fast Ethernet0/0
                                       no shutdown
                                       ip address 10.4.9.34 255.255.255.0
                                       duplex auto
                                       speed auto
                                      !
                                      interface Fast Ethernet1/0
                                       ip address 172.16.1.2 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3
                                       no shtdown
                                       duplex auto
                                       speed auto
                                      !
                                      router eigrp 11
                                       network 172.16.0.0
                                       bfd all-interfaces
                                       auto-summary
                                      !
                                      ip default-gateway 10.4.9.1
                                      ip default-network 0.0.0.0
                                      ip route 0.0.0.0 0.0.0.0 10.4.9.1
                                      ip route 172.16.1.129 255.255.255.255 10.4.9.1
                                      !
                                      no ip http server
                                      !
                                      logging alarm informational
                                      !
                                      control-plane
                                      !
                                      line con 0
                                       exec-timeout 30 0
                                       stopbits 1
                                      line aux 0
                                       stopbits 1
                                      line vty 0 4
                                       login
                                      !
                                      !
                                      end

                                      Configuration for RouterC

                                      !
                                      !
                                      interface Fast Ethernet0/0
                                       no shutdown
                                       ip address 10.4.9.34 255.255.255.0
                                       duplex auto
                                       speed auto
                                      !
                                      interface Fast Ethernet1/0
                                       ip address 172.16.1.2 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3
                                       no shutdown
                                       duplex auto
                                       speed auto
                                      !
                                      router eigrp 11
                                       network 172.16.0.0
                                       bfd all-interfaces
                                       auto-summary
                                      !
                                      ip default-gateway 10.4.9.1
                                      ip default-network 0.0.0.0
                                      ip route 0.0.0.0 0.0.0.0 10.4.9.1
                                      ip route 172.16.1.129 255.255.255.255 10.4.9.1
                                      !
                                      no ip http server
                                      !
                                      logging alarm informational
                                      !
                                      control-plane
                                      !
                                      line con 0
                                       exec-timeout 30 0
                                       stopbits 1
                                      line aux 0
                                       stopbits 1
                                      line vty 0 4
                                       login
                                      !
                                      !
                                      end
                                      

                                      The output from the show bfd neighbors details command from RouterA verifies that BFD sessions have been created among all three routers and that EIGRP is registered for BFD support. The first group of output shows that RouterC with the IP address 172.16.1.3 runs BFD Version 0 and therefore does not use the echo mode. The second group of output shows that RouterB with the IP address 172.16.1.2 does run BFD Version 1, and the 50 millisecond BFD interval parameter had been adopted. The relevant command output is shown in bold in the output.

                                      
                                      RouterA# show bfd neighbors details
                                      
                                      OurAddr
                                             NeighAddr
                                            LD/RD  RH/RS    Holdown(mult)  State     Int
                                      172.16.1.1 172.16.1.3
                                           5/3    1(RH)    150 (3 )       Up   Fa1/0 
                                      Session state is UP and not using echo function.
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 50000, MinRxInt: 50000, Multiplier: 3
                                      Received MinRxInt: 50000, Received Multiplier: 3
                                      Holdown (hits): 150(0), Hello (hits): 50(1364284)
                                      Rx Count: 1351813, Rx Interval (ms) min/max/avg: 28/64/49 last: 4 ms ago
                                      Tx Count: 1364289, Tx Interval (ms) min/max/avg: 40/68/49 last: 32 ms ago
                                      Registered protocols: EIGRP
                                      Uptime: 18:42:45
                                      Last packet: Version: 0
                                                  - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 3          - Your Discr.: 5
                                                   Min tx interval: 50000    - Min rx interval: 50000
                                                   Min Echo interval: 0
                                      OurAddr NeighAddr
                                           LD/RD  RH/RS   Holdown(mult)  State     Int
                                      172.16.1.1 172.16.1.2
                                       
                                          6/1    Up        0    (3 )   Up        Fa1/0 
                                      Session state is UP and using echo function with 50 ms interval.
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
                                      Received MinRxInt: 1000000, Received Multiplier: 3
                                      Holdown (hits): 3000(0), Hello (hits): 1000(317)
                                      Rx Count: 305, Rx Interval (ms) min/max/avg: 1/1016/887 last: 448 ms ago
                                      Tx Count: 319, Tx Interval (ms) min/max/avg: 1/1008/880 last: 532 ms ago
                                      Registered protocols: EIGRP
                                      Uptime: 00:04:30
                                      Last packet: Version: 1
                                       
                                               - Diagnostic: 0
                                                   State bit: Up         - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 1          - Your Discr.: 6
                                                   Min tx interval: 1000000    - Min rx interval: 1000000
                                                   Min Echo interval: 50000
                                      

                                      The output from the show bfd neighbors details command on Router B verifies that BFD sessions have been created and that EIGRP is registered for BFD support. As previously noted, RouterA runs BFD Version 1, therefore echo mode is running, and RouterC runs BFD Version 0, so echo mode does not run. The relevant command output is shown in bold in the output.

                                      
                                      RouterB# show bfd neighbors details 
                                      
                                      OurAddr NeighAddr
                                           LD/RD  RH/RS   Holdown(mult)  State     Int
                                      172.16.1.2 172.16.1.1 
                                          1/6    Up        0    (3 )   Up        Fa1/0 
                                      Session state is UP and using echo function with 50 ms interval.
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 1000000, MinRxInt: 1000000, Multiplier: 3
                                      Received MinRxInt: 1000000, Received Multiplier: 3
                                      Holdown (hits): 3000(0), Hello (hits): 1000(337)
                                      Rx Count: 341, Rx Interval (ms) min/max/avg: 1/1008/882 last: 364 ms ago
                                      Tx Count: 339, Tx Interval (ms) min/max/avg: 1/1016/886 last: 632 ms ago
                                      Registered protocols: EIGRP
                                      Uptime: 00:05:00
                                      Last packet: Version: 1 
                                                 - Diagnostic: 0
                                                   State bit: Up         - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 6          - Your Discr.: 1
                                                   Min tx interval: 1000000    - Min rx interval: 1000000
                                                   Min Echo interval: 50000
                                      OurAddr NeighAddr 
                                       
                                       LD/RD  RH/RS   Holdown(mult)  State     Int
                                      172.16.1.2 172.16.1.3
                                           3/6    1(RH)     118  (3 )   Up        Fa1/0 
                                      Session state is UP and not using echo function.
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 50000, MinRxInt: 50000, Multiplier: 3
                                      Received MinRxInt: 50000, Received Multiplier: 3
                                      Holdown (hits): 150(0), Hello (hits): 50(5735)
                                      Rx Count: 5731, Rx Interval (ms) min/max/avg: 32/72/49 last: 32 ms ago
                                      Tx Count: 5740, Tx Interval (ms) min/max/avg: 40/64/50 last: 44 ms ago
                                      Registered protocols: EIGRP
                                      Uptime: 00:04:45
                                      Last packet: Version: 0
                                                  - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 6          - Your Discr.: 3
                                                   Min tx interval: 50000    - Min rx interval: 50000
                                                   Min Echo interval: 0
                                      

                                      The figure below shows that Fast Ethernet interface 1/0 on RouterB has failed. When Fast Ethernet interface 1/0 on RouterB is shut down, the BFD statistics of the corresponding BFD sessions on RouterA and RouterB are reduced.

                                      When Fast Ethernet interface 1/0 on RouterB fails, BFD will no longer detect Router B as a BFD neighbor for RouterA or for RouterC. In this example, Fast Ethernet interface 1/0 has been administratively shut down on RouterB.

                                      The following output from the show bfd neighbors command on RouterA now shows only one BFD neighbor for RouterA in the EIGRP network. The relevant command output is shown in bold in the output.

                                      RouterA# show bfd neighbors
                                      OurAddr NeighAddr
                                       
                                          LD/RD  RH/RS   Holdown(mult)  State     Int
                                      172.16.1.1 172.16.1.3
                                       
                                          5/3    1(RH)     134  (3 )   Up        Fa1/0 
                                      

                                      The following output from the show bfd neighbors command on RouterC also now shows only one BFD neighbor for RouterC in the EIGRP network. The relevant command output is shown in bold in the output.

                                      RouterC# show bfd neighbors
                                      
                                      OurAddr NeighAddr 
                                       
                                         LD/RD RH  Holdown(mult)  State     Int
                                      172.16.1.3 172.16.1.1
                                       
                                          3/5  1   114  (3 )      Up        Fa1/0 

                                      Example: Configuring BFD in an OSPF Network

                                      The following example shows how to configure BFD in an OSPF network in Cisco IOS Release 12.0(31)S. In the following example, the simple OSPF network consists of Router A and Router B. Fast Ethernet interface 0/1 on Router A is connected to the same network as Fast Ethernet interface 6/0 in Router B. The example, starting in global configuration mode, shows the configuration of BFD. For both Routers A and B, BFD is configured globally for all interfaces associated with the OSPF process.

                                      Configuration for Router A

                                      !
                                      interface Fast Ethernet 0/1
                                       ip address 172.16.10.1 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3
                                      !
                                      interface Fast Ethernet 3/0.1
                                      ip address 172.17.0.1 255.255.255.0
                                      !
                                      router ospf 123
                                       log-adjacency-changes detail
                                       network 172.16.0.0 0.0.0.255 area 0
                                       network 172.17.0.0 0.0.0.255 area 0
                                       bfd all-interfaces

                                      Configuration for Router B

                                      !
                                      interface Fast Ethernet 6/0
                                       ip address 172.16.10.2 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3
                                      !
                                      interface Fast Ethernet 6/1
                                       ip address 172.18.0.1 255.255.255.0
                                      !
                                      router ospf 123
                                       log-adjacency-changes detail
                                       network 172.16.0.0 0.0.255.255 area 0
                                       network 172.18.0.0 0.0.255.255 area 0
                                       bfd all-interfaces
                                      

                                      The output from the show bfd neighbors details command verifies that a BFD session has been created and that OSPF is registered for BFD support. The relevant command output is shown in bold in the output.

                                      Router A

                                      RouterA# show bfd neighbors details
                                      OurAddr       NeighAddr     LD/RD RH  Holdown(mult)  State     Int
                                      172.16.10.1   172.16.10.2    1/2  1   532  (3 )      Up        Fa0/1          
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 200000, MinRxInt: 200000, Multiplier: 5
                                      Received MinRxInt: 1000, Received Multiplier: 3
                                      Holdown (hits): 600(22), Hello (hits): 200(84453)
                                      Rx Count: 49824, Rx Interval (ms) min/max/avg: 208/440/332 last: 68 ms ago
                                      Tx Count: 84488, Tx Interval (ms) min/max/avg: 152/248/196 last: 192 ms ago
                                      Registered protocols: OSPF
                                      Uptime: 02:18:49
                                      Last packet: Version: 0
                                                  - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 2          - Your Discr.: 1
                                                   Min tx interval: 50000    - Min rx interval: 1000
                                                   Min Echo interval: 0
                                      

                                      The output from the show bfd neighbors details command from the line card on Router B verifies that a BFD session has been created:


                                      Note


                                      Router B is a Cisco 12000 series router. The show bfd neighbors details command must be run on the line cards. The show bfd neighbors details command will not display the registered protocols when it is entered on a line card.


                                      Router B

                                      RouterB# attach 6 
                                      Entering Console for 8 Port Fast Ethernet in Slot: 6
                                      Type "exit" to end this session
                                      Press RETURN to get started!
                                      Router> show bfd neighbors details
                                      Cleanup timer hits: 0
                                      OurAddr       NeighAddr     LD/RD RH  Holdown(mult)  State     Int
                                      172.16.10.2   172.16.10.1    8/1  1   1000 (5 )      Up        Fa6/0          
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 50000, MinRxInt: 1000, Multiplier: 3
                                      Received MinRxInt: 200000, Received Multiplier: 5
                                      Holdown (hits): 1000(0), Hello (hits): 200(5995)
                                      Rx Count: 10126, Rx Interval (ms) min/max/avg: 152/248/196 last: 0 ms ago
                                      Tx Count: 5998, Tx Interval (ms) min/max/avg: 204/440/332 last: 12 ms ago
                                      Last packet: Version: 0            - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 5         - Length: 24
                                                   My Discr.: 1          - Your Discr.: 8
                                                   Min tx interval: 200000    - Min rx interval: 200000
                                                   Min Echo interval: 0
                                      Uptime: 00:33:13
                                      SSO Cleanup Timer called: 0
                                      SSO Cleanup Action Taken: 0
                                      Pseudo pre-emptive process count: 239103 min/max/avg: 8/16/8 last: 0 ms ago
                                       IPC Tx Failure Count: 0
                                       IPC Rx Failure Count: 0
                                       Total Adjs Found: 1
                                      

                                      The output of the show ip ospf command verifies that BFD has been enabled for OSPF. The relevant command output is shown in bold in the output.

                                      Router A

                                      RouterA# show ip ospf
                                      
                                       Routing Process "ospf 123" with ID 172.16.10.1
                                       Supports only single TOS(TOS0) routes
                                       Supports opaque LSA
                                       Supports Link-local Signaling (LLS)
                                       Initial SPF schedule delay 5000 msecs
                                       Minimum hold time between two consecutive SPFs 10000 msecs
                                       Maximum wait time between two consecutive SPFs 10000 msecs
                                       Incremental-SPF disabled
                                       Minimum LSA interval 5 secs
                                       Minimum LSA arrival 1000 msecs
                                       LSA group pacing timer 240 secs
                                       Interface flood pacing timer 33 msecs
                                       Retransmission pacing timer 66 msecs
                                       Number of external LSA 0. Checksum Sum 0x000000
                                       Number of opaque AS LSA 0. Checksum Sum 0x000000
                                       Number of DCbitless external and opaque AS LSA 0
                                       Number of DoNotAge external and opaque AS LSA 0
                                       Number of areas in this router is 1. 1 normal 0 stub 0 nssa
                                       External flood list length 0
                                       BFD is enabled
                                          Area BACKBONE(0)
                                              Number of interfaces in this area is 2 (1 loopback)
                                              Area has no authentication
                                              SPF algorithm last executed 00:00:08.828 ago
                                              SPF algorithm executed 9 times
                                              Area ranges are
                                              Number of LSA 3. Checksum Sum 0x028417
                                              Number of opaque link LSA 0. Checksum Sum 0x000000
                                              Number of DCbitless LSA 0
                                              Number of indication LSA 0
                                              Number of DoNotAge LSA 0
                                              Flood list length 0
                                      

                                      Router B

                                      RouterB# show ip ospf
                                      
                                       Routing Process "ospf 123" with ID 172.18.0.1
                                       Supports only single TOS(TOS0) routes
                                       Supports opaque LSA
                                       Supports Link-local Signaling (LLS)
                                       Supports area transit capability
                                       Initial SPF schedule delay 5000 msecs
                                       Minimum hold time between two consecutive SPFs 10000 msecs
                                       Maximum wait time between two consecutive SPFs 10000 msecs
                                       Incremental-SPF disabled
                                       Minimum LSA interval 5 secs
                                       Minimum LSA arrival 1000 msecs
                                       LSA group pacing timer 240 secs
                                       Interface flood pacing timer 33 msecs
                                       Retransmission pacing timer 66 msecs
                                       Number of external LSA 0. Checksum Sum 0x0     
                                       Number of opaque AS LSA 0. Checksum Sum 0x0     
                                       Number of DCbitless external and opaque AS LSA 0
                                       Number of DoNotAge external and opaque AS LSA 0
                                       Number of areas in this router is 1. 1 normal 0 stub 0 nssa
                                       Number of areas transit capable is 0
                                       External flood list length 0
                                       BFD is enabled
                                          Area BACKBONE(0)
                                              Number of interfaces in this area is 2 (1 loopback)
                                              Area has no authentication
                                              SPF algorithm last executed 02:07:30.932 ago
                                              SPF algorithm executed 7 times
                                              Area ranges are
                                              Number of LSA 3. Checksum Sum 0x28417 
                                              Number of opaque link LSA 0. Checksum Sum 0x0     
                                              Number of DCbitless LSA 0
                                              Number of indication LSA 0
                                              Number of DoNotAge LSA 0
                                              Flood list length 0
                                      

                                      The output of the show ip ospf interface command verifies that BFD has been enabled for OSPF on the interfaces connecting Router A and Router B. The relevant command output is shown in bold in the output.

                                      Router A

                                      RouterA# show ip ospf interface Fast Ethernet 0/1
                                      show ip ospf interface Fast Ethernet 0/1 
                                      Fast Ethernet0/1 is up, line protocol is up 
                                        Internet Address 172.16.10.1/24, Area 0 
                                        Process ID 123, Router ID 172.16.10.1, Network Type BROADCAST, Cost: 1
                                        Transmit Delay is 1 sec, State BDR, Priority 1, BFD enabled
                                        Designated Router (ID) 172.18.0.1, Interface address 172.16.10.2
                                        Backup Designated router (ID) 172.16.10.1, Interface address 172.16.10.1
                                        Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
                                          oob-resync timeout 40
                                          Hello due in 00:00:03
                                        Supports Link-local Signaling (LLS)
                                        Index 1/1, flood queue length 0
                                        Next 0x0(0)/0x0(0)
                                        Last flood scan length is 1, maximum is 1
                                        Last flood scan time is 0 msec, maximum is 0 msec
                                        Neighbor Count is 1, Adjacent neighbor count is 1 
                                          Adjacent with neighbor 172.18.0.1  (Designated Router)
                                        Suppress hello for 0 neighbor(s)

                                      Router B

                                      RouterB# show ip ospf interface Fast Ethernet 6/1
                                      Fast Ethernet6/1 is up, line protocol is up 
                                        Internet Address 172.18.0.1/24, Area 0 
                                        Process ID 123, Router ID 172.18.0.1, Network Type BROADCAST, Cost: 1
                                        Transmit Delay is 1 sec, State DR, Priority 1, BFD enabled
                                        Designated Router (ID) 172.18.0.1, Interface address 172.18.0.1
                                        No backup designated router on this network
                                        Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
                                          oob-resync timeout 40
                                          Hello due in 00:00:01
                                        Supports Link-local Signaling (LLS)
                                        Index 1/1, flood queue length 0
                                        Next 0x0(0)/0x0(0)
                                        Last flood scan length is 0, maximum is 0
                                        Last flood scan time is 0 msec, maximum is 0 msec
                                        Neighbor Count is 0, Adjacent neighbor count is 0 
                                        Suppress hello for 0 neighbor(s)

                                      Example: Configuring BFD in a BGP Network

                                      The following example shows how to configure BFD in a BGP network in Cisco IOS Release 12.0(31)S. In the following example, the simple BGP network consists of Router A and Router B. Fast Ethernet interface 0/1 on Router A is connected to the same network as Fast Ethernet interface 6/0 in Router B. The example, starting in global configuration mode, shows the configuration of BFD.

                                      Configuration for Router A

                                      !
                                      interface Fast Ethernet 0/1
                                       ip address 172.16.10.1 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3
                                      !
                                      interface Fast Ethernet 3/0.1
                                      ip address 172.17.0.1 255.255.255.0
                                      !
                                      !
                                      router bgp 40000
                                       bgp log-neighbor-changes
                                       neighbor 172.16.10.2 remote-as 45000
                                       neighbor 172.16.10.2 fall-over bfd
                                       !
                                       address-family ipv4
                                       neighbor 172.16.10.2 activate
                                       no auto-summary
                                       no synchronization
                                       network 172.18.0.0 mask 255.255.255.0
                                       exit-address-family
                                      !

                                      Configuration for Router B

                                      !
                                      interface Fast Ethernet 6/0
                                       ip address 172.16.10.2 255.255.255.0
                                       bfd interval 50 min_rx 50 multiplier 3
                                      !
                                      interface Fast Ethernet 6/1
                                       ip address 172.18.0.1 255.255.255.0
                                      !
                                      router bgp 45000
                                       bgp log-neighbor-changes
                                       neighbor 172.16.10.1 remote-as 40000
                                       neighbor 172.16.10.1 fall-over bfd
                                       !
                                       address-family ipv4
                                       neighbor 172.16.10.1 activate
                                       no auto-summary
                                       no synchronization
                                       network 172.17.0.0 mask 255.255.255.0
                                       exit-address-family
                                      !
                                      

                                      The output from the show bfd neighbors details command from Router A verifies that a BFD session has been created and that BGP is registered for BFD support. The relevant command output is shown in bold in the output.

                                      Router A

                                      RouterA# show bfd neighbors details
                                       
                                      OurAddr       NeighAddr     LD/RD RH  Holdown(mult)  State     Int
                                      172.16.10.1   172.16.10.2    1/8  1   332  (3 )      Up        Fa0/1          
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 200000, MinRxInt: 200000, Multiplier: 5
                                      Received MinRxInt: 1000, Received Multiplier: 3
                                      Holdown (hits): 600(0), Hello (hits): 200(15491)
                                      Rx Count: 9160, Rx Interval (ms) min/max/avg: 200/440/332 last: 268 ms ago
                                      Tx Count: 15494, Tx Interval (ms) min/max/avg: 152/248/197 last: 32 ms ago
                                      Registered protocols: BGP
                                      Uptime: 00:50:45
                                      Last packet: Version: 0            - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 8          - Your Discr.: 1
                                                   Min tx interval: 50000    - Min rx interval: 1000
                                                   Min Echo interval: 0
                                      

                                      The output from the show bfd neighbors details command from the line card on Router B verifies that a BFD session has been created:


                                      Note


                                      Router B is a Cisco 12000 series router. The show bfd neighbors details command must be run on the line cards. The show bfd neighbors details command will not display the registered protocols when it is entered on a line card.


                                      Router B

                                      RouterB# attach 6
                                      Entering Console for 8 Port Fast Ethernet in Slot: 6
                                      Type "exit" to end this session
                                      Press RETURN to get started!
                                      Router> show bfd neighbors details
                                      Cleanup timer hits: 0
                                      OurAddr       NeighAddr     LD/RD RH  Holdown(mult)  State     Int
                                      172.16.10.2   172.16.10.1    8/1  1   1000 (5 )      Up        Fa6/0          
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 50000, MinRxInt: 1000, Multiplier: 3
                                      Received MinRxInt: 200000, Received Multiplier: 5
                                      Holdown (hits): 1000(0), Hello (hits): 200(5995)
                                      Rx Count: 10126, Rx Interval (ms) min/max/avg: 152/248/196 last: 0 ms ago
                                      Tx Count: 5998, Tx Interval (ms) min/max/avg: 204/440/332 last: 12 ms ago
                                      Last packet: Version: 0            - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 5         - Length: 24
                                                   My Discr.: 1          - Your Discr.: 8
                                                   Min tx interval: 200000    - Min rx interval: 200000
                                                   Min Echo interval: 0
                                      Uptime: 00:33:13
                                      SSO Cleanup Timer called: 0
                                      SSO Cleanup Action Taken: 0
                                      Pseudo pre-emptive process count: 239103 min/max/avg: 8/16/8 last: 0 ms ago
                                       IPC Tx Failure Count: 0
                                       IPC Rx Failure Count: 0
                                       Total Adjs Found: 1
                                      

                                      The output of the show ip bgp neighbors command verifies that BFD has been enabled for the BGP neighbors:

                                      Router A

                                      RouterA# show ip bgp neighbors
                                      BGP neighbor is 172.16.10.2,  remote AS 45000, external link
                                       Using BFD to detect fast fallover
                                      .
                                      .
                                      .

                                      Router B

                                      RouterB# show ip bgp neighbors
                                      BGP neighbor is 172.16.10.1,  remote AS 40000, external link
                                       Using BFD to detect fast fallover
                                      .
                                      .
                                      .

                                      Example: Configuring BFD in an IS-IS Network

                                      The following example shows how to configure BFD in an IS-IS network in Cisco IOS Release 12.0(31)S. In the following example, the simple IS-IS network consists of Router A and Router B. Fast Ethernet interface 0/1 on Router A is connected to the same network as Fast Ethernet interface 6/0 for Router B. The example, starting in global configuration mode, shows the configuration of BFD.

                                      Configuration for Router A

                                      !
                                      interface Fast Ethernet 0/1
                                       ip address 172.16.10.1 255.255.255.0
                                      ip router isis 
                                       bfd interval 50 min_rx 50 multiplier 3
                                      !
                                      interface Fast Ethernet 3/0.1
                                      ip address 172.17.0.1 255.255.255.0
                                      ip router isis 
                                      !
                                      router isis 
                                       net 49.0001.1720.1600.1001.00
                                       bfd all-interfaces
                                      !

                                      Configuration for Router B

                                      !
                                      interface Fast Ethernet 6/0
                                       ip address 172.16.10.2 255.255.255.0
                                      ip router isis 
                                       bfd interval 50 min_rx 50 multiplier 3
                                      !
                                      interface Fast Ethernet 6/1
                                       ip address 172.18.0.1 255.255.255.0
                                      ip router isis 
                                      !
                                      router isis 
                                       net 49.0000.0000.0002.00
                                       bfd all-interfaces
                                      !
                                      

                                      The output from the show bfd neighbors details command from Router A verifies that a BFD session has been created and that IS-IS is registered for BFD support:

                                      RouterA# show bfd neighbors details
                                       
                                      OurAddr       NeighAddr     LD/RD RH  Holdown(mult)  State     Int
                                      172.16.10.1   172.16.10.2    1/8  1   536  (3 )      Up        Fa0/1          
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 200000, MinRxInt: 200000, Multiplier: 5
                                      Received MinRxInt: 1000, Received Multiplier: 3
                                      Holdown (hits): 600(0), Hello (hits): 200(23543)
                                      Rx Count: 13877, Rx Interval (ms) min/max/avg: 200/448/335 last: 64 ms ago
                                      Tx Count: 23546, Tx Interval (ms) min/max/avg: 152/248/196 last: 32 ms ago
                                      Registered protocols: ISIS 
                                      Uptime: 01:17:09
                                      Last packet: Version: 0            - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 3         - Length: 24
                                                   My Discr.: 8          - Your Discr.: 1
                                                   Min tx interval: 50000    - Min rx interval: 1000
                                                   Min Echo interval: 0
                                      

                                      The output from the show bfd neighbors details command from the line card on Router B verifies that a BFD session has been created:


                                      Note


                                      Router B is a Cisco 12000 series router. The show bfd neighbors details command must be run on the line cards. The show bfd neighbors details command will not display the registered protocols when it is entered on a line card.


                                      RouterB# attach 6 
                                      
                                      Entering Console for 8 Port Fast Ethernet in Slot: 6
                                      Type "exit" to end this session
                                      Press RETURN to get started!
                                      Router> show bfd neighbors details
                                      Cleanup timer hits: 0
                                      OurAddr       NeighAddr     LD/RD RH  Holdown(mult)  State     Int
                                      172.16.10.2   172.16.10.1    8/1  1   1000 (5 )      Up        Fa6/0          
                                      Local Diag: 0, Demand mode: 0, Poll bit: 0
                                      MinTxInt: 50000, MinRxInt: 1000, Multiplier: 3
                                      Received MinRxInt: 200000, Received Multiplier: 5
                                      Holdown (hits): 1000(0), Hello (hits): 200(5995)
                                      Rx Count: 10126, Rx Interval (ms) min/max/avg: 152/248/196 last: 0 ms ago
                                      Tx Count: 5998, Tx Interval (ms) min/max/avg: 204/440/332 last: 12 ms ago
                                      Last packet: Version: 0            - Diagnostic: 0
                                                   I Hear You bit: 1     - Demand bit: 0
                                                   Poll bit: 0           - Final bit: 0
                                                   Multiplier: 5         - Length: 24
                                                   My Discr.: 1          - Your Discr.: 8
                                                   Min tx interval: 200000    - Min rx interval: 200000
                                                   Min Echo interval: 0
                                      Uptime: 00:33:13
                                      SSO Cleanup Timer called: 0
                                      SSO Cleanup Action Taken: 0
                                      Pseudo pre-emptive process count: 239103 min/max/avg: 8/16/8 last: 0 ms ago
                                       IPC Tx Failure Count: 0
                                       IPC Rx Failure Count: 0
                                       Total Adjs Found: 1

                                      Example: Configuring BFD in an HSRP Network

                                      In the following example, the HSRP network consists of Router A and Router B. Fast Ethernet interface 2/0 on Router A is connected to the same network as Fast Ethernet interface 2/0 on Router B. The example, starting in global configuration mode, shows the configuration of BFD.


                                      Note


                                      In the following example, the standby bfd and the standby bfd all-interfaces commands are not displayed. HSRP support for BFD peering is enabled by default when BFD is configured on the router or interface using the bfd interval command. The standby bfdand standby bfd all-interfaces commands are needed only if BFD has been manually disabled on a router or interface.


                                      Router A

                                      ip cef
                                      interface Fast Ethernet2/0
                                       no shutdown
                                       ip address 10.0.0.2 255.0.0.0
                                       ip router-cache cef
                                       bfd interval 200 min_rx 200 multiplier 3
                                       standby 1 ip 10.0.0.11
                                       standby 1 preempt
                                       standby 1 priority 110
                                       
                                       standby 2 ip 10.0.0.12
                                       standby 2 preempt
                                       standby 2 priority 110

                                      Router B

                                      interface Fast Ethernet2/0
                                       ip address 10.1.0.22 255.255.0.0
                                       no shutdown
                                       bfd interval 200 min_rx 200 multiplier 3
                                       standby 1 ip 10.0.0.11
                                       standby 1 preempt
                                       standby 1 priority 90
                                       standby 2 ip 10.0.0.12
                                       standby 2 preempt
                                       standby 2 priority 80
                                      

                                      The output from the show standby neighbors command verifies that a BFD session has been created:

                                      RouterA#show standby neighbors
                                      
                                      HSRP neighbors on Fast Ethernet2/0
                                        10.1.0.22
                                          No active groups
                                          Standby groups: 1
                                          BFD enabled !
                                      RouterB# show standby neighbors
                                      
                                      HSRP neighbors on Fast Ethernet2/0
                                        10.0.0.2
                                          Active groups: 1
                                          No standby groups
                                          BFD enabled !

                                      Example: Configuring BFD Support for Static Routing

                                      In the following example, the network consists of Router A and Router B. Serial interface 2/0 on Router A is connected to the same network as serial interface 2/0 on Router B. In order for the BFD session to come up, Router B must be configured.

                                      Router A

                                      configure terminal
                                       interface Serial 2/0
                                       ip address 10.201.201.1 255.255.255.0
                                       bfd interval 500 min_rx 500 multiplier 5
                                       ip route static bfd Serial 2/0 10.201.201.2
                                       ip route 10.0.0.0 255.0.0.0 Serial 2/0 10.201.201.2

                                      Router B

                                      configure terminal
                                       interface Serial 2/0
                                       ip address 10.201.201.2 255.255.255.0
                                       bfd interval 500 min_rx 500 multiplier 5
                                       ip route static bfd Serial 2/0 10.201.201.1
                                       ip route 10.1.1.1 255.255.255.255 Serial 2/0 10.201.201.1
                                      

                                      Note that the static route on Router B exists solely to enable the BFD session between 10.201.201.1 and 10.201.201.2. If there is no useful static route that needs to be configured, select a prefix that will not affect packet forwarding, for example, the address of a locally configured loopback interface.

                                      In the following example, there is an active static BFD configuration to reach 209.165.200.225 through Ethernet interface 0/0 in the BFD group testgroup. As soon as the static route is configured that is tracked by the configured static BFD, a single hop BFD session is initiated to 209.165.200.225 through Ethernet interface 0/0. The prefix 10.0.0.0/8 is added to the RIB if a BFD session is successfully established.

                                      configure terminal
                                       ip route static bfd Ethernet 0/0 209.165.200.225 group testgroup
                                       ip route 10.0.0.0 255.255.255.224 Ethernet 0/0 209.165.200.225
                                      

                                      In the following example, a BFD session to 209.165.200.226 through Ethernet interface 0/0.1001 is marked to use the group testgroup. That is, this configuration is a passive static BFD. Though there are static routes to be tracked by the second static BFD configuration, a BFD session is not triggered for 209.165.200.226 through Ethernet interface 0/0.1001. The existence of the prefixes 10.1.1.1/8 and 10.2.2.2/8 is controlled by the active static BFD session (Ethernet interface 0/0 209.165.200.225).

                                      configure terminal
                                       ip route static bfd Ethernet 0/0 209.165.200.225 group testgroup
                                       ip route 10.0.0.0 255.255.255.224 Ethernet 0/0 209.165.200.225
                                       ip route static bfd Ethernet 0/0.1001 209.165.200.226 group testgroup passive
                                       ip route 10.1.1.1 255.255.255.224 Ethernet 0/0.1001 209.165.200.226
                                       ip route 10.2.2.2 255.255.255.224 Ethernet 0/0.1001 209.165.200.226

                                      Example: Configuring BFD Control Channel over VCCV--Support for ATM Pseudowire

                                      The figure below shows a typical ATM pseudowire configuration. The network consists of a MPLS pseudowire carrying an ATM payload between two terminating provider edge (T-PE) devices: T-PE1 and T-PE2. BFD monitoring of the pseudowire occurs between the T-PE1 device and the switching providing edge (S-PE) device, and between the S-PE device and the T-PE2 device. BFD also monitors the signal status of the ACs between the customer edge (CE) devices and the T-PE devices.


                                      Note


                                      No configuration specific to BFD control channel over VCCV is required for the S-PEs.


                                      CE1

                                      interface ATM 0/0
                                       description connect to mfi6 atm9/0/0
                                       no ip address
                                       no ip directed-broadcast
                                       atm clock INTERNAL
                                       atm sonet stm-1
                                       no atm enable-ilmi-trap
                                       no atm ilmi-keepalive
                                      !
                                      interface ATM 0/0.2 point-to-point
                                       ip address 10.25.1.1 255.255.255.0
                                       no ip directed-broadcast
                                       no atm enable-ilmi-trap
                                       pvc 0/100
                                        encapsulation aal5snap

                                      T-PE1

                                      interface Loopback 0
                                       ip address 10.0.0.6 255.255.255.255
                                      bfd-template single-hop nsn
                                       interval min-tx 500 min-rx 500 multiplier 3
                                      pseudowire-class vccv-bfd1
                                       encapsulation mpls
                                       vccv bfd template nsn raw-bfd
                                       vccv bfd status signaling
                                      interface ATM 9/0/0
                                       description connect mfr4 atm0/0 
                                       no ip address
                                       atm asynchronous
                                       atm clock INTERNAL
                                       no atm ilmi-keepalive
                                       no atm enable-ilmi-trap
                                       pvc 0/100 l2transport
                                        xconnect 10.0.0.7 100 pw-class vccv-bfd1

                                      T-PE2

                                      interface Loopback 0
                                       ip address 10.54.0.1 255.255.255.255
                                      bfd-template single-hop nsn
                                       interval min-tx 500 min-rx 500 multiplier 3
                                      !
                                      pseudowire-class vccv-bfd1
                                       encapsulation mpls
                                       vccv bfd template nsn raw-bfd
                                       vccv bfd status signaling 
                                      interface ATM 2/0
                                       no ip address
                                       atm asynchronous
                                       no atm ilmi-keepalive
                                       no atm enable-ilmi-trap
                                       pvc 0/100 l2transport
                                        xconnect 10.0.0.7 102 pw-class vccv-bfd1
                                       !

                                      CE2

                                      interface ATM 4/0.2 point-to-point
                                       ip address 10.25.1.2 255.255.255.0
                                       no snmp trap link-status
                                       pvc 0/100 
                                        encapsulation aal5snap

                                      Additional References

                                      Related Documents

                                      Related Topic

                                      Document Title

                                      Cisco IOS commands

                                      Cisco IOS Master Commands List, All Releases

                                      Configuring and monitoring BGP

                                      “Cisco BGP Overview” module of the Cisco IOS IP Routing Protocols Configuration Guide

                                      BFD hardware offload

                                      “Configuring Synchronous Ethernet on the Cisco 7600 Router with ES+ Line Card” section of the Cisco 7600 Series Ethernet Services Plus (ES+) and Ethernet Services Plus T (ES+T) Line Card Configuration Guide

                                      Configuring and monitoring EIGRP

                                      “Configuring EIGRP” module of the Cisco IOS IP Routing Protocols Configuration Guide

                                      Configuring and monitoring HSRP

                                      “Configuring HSRP” module of the Cisco IOS IP Application Services Configuration Guide

                                      Configuring and monitoring IS-IS

                                      “Configuring Integrated IS-IS” module of the Cisco IOS IP Routing Protocols Configuration Guide

                                      Configuring and monitoring OSPF

                                      “Configuring OSPF” module of the Cisco IOS IP Routing Protocols Configuration Guide

                                      BFD commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

                                      Cisco IOS IP Routing: Protocol-Independent Command Reference

                                      BGP commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

                                      Cisco IOS IP Routing: Protocol-Independent Command Reference

                                      EIGRP commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

                                      Cisco IOS IP Routing: Protocol-Independent Command Reference

                                      HSRP commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

                                      Cisco IOS IP Application Services Command Reference

                                      IS-IS commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

                                      Cisco IOS IP Routing: Protocol-Independent Command Reference

                                      OSPF commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples

                                      Cisco IOS IP Routing: Protocol-Independent Command Reference

                                      BFD IPv6 Encapsulation Support

                                      BFD IPv6 Encapsulation Support” module

                                      OSPFv3 for BFD

                                      OSPFv3 for BFD” module

                                      Static Route Support for BFD over IPv6

                                      Static Route Support for BFD over IPv6” module

                                      Standards and RFCs

                                      Standard/RFC

                                      Title

                                      IETF Draft

                                      Bidirectional Forwarding Detection, February 2009

                                      (http://tools.ietf.org/html/draft-ietf-bfd-base-09)

                                      IETF Draft

                                      BFD for IPv4 and IPv6 (Single Hop), February 2009

                                      (http://tools.ietf.org/html/draft-ietf-bfd-v4v6-1hop-09

                                      Technical Assistance

                                      Description

                                      Link

                                      The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

                                      http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

                                      Feature Information for Bidirectional Forwarding Detection

                                      The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

                                      Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

                                      Table 5 Feature Information for Bidirectional Forwarding Detection

                                      Feature Name

                                      Releases

                                      Feature Information

                                      BFD Control Channel over VCCV—Support for ATM Pseudowire

                                      15.0(1)S

                                      VCCV provides a control channel that is associated with an ATM pseudowire to perform operations and management functions over the pseudowire. BFD uses the VCCV control channel to detect dataplane failures for pseudowires.

                                      In Cisco IOS Release 15.0(1)S the BFD control channel over VCCV Support for ATM Pseudowire feature is supported for VCCV type-1 (without an IP/UDP header) only.

                                      The following commands were introduced or modified by this feature: bfd-template, debug mpls l2transport vc vccv, interval(BFD), vccv, vccv bfd template, vccv bfd status signaling.

                                      BFD Echo Mode

                                      12.2(33)SRB

                                      12.4(9)T

                                      15.0(1)S

                                      BFD echo mode works with asynchronous BFD. Echo packets are sent by the forwarding engine and forwarded back along the same path in order to perform detection--the BFD session at the other end does not participate in the actual forwarding of the echo packets. The echo function and the forwarding engine are responsible for the detection process, therefore the number of BFD control packets that are sent out between two BFD neighbors is reduced. And since the forwarding engine is testing the forwarding path on the remote (neighbor) system without involving the remote system, there is an opportunity to improve the interpacket delay variance, thereby achieving quicker failure detection times than when using BFD Version 0 with BFD control packets for the BFD session.

                                      BFD—EIGRP Support

                                      12.0(31)S

                                      12.2(18)SXE

                                      12.2(33)SRA

                                      12.2(33)SRB

                                      12.4(4)T

                                      15.1(1)SG

                                      BFD support for EIGRP can be configured so that EIGRP is a registered protocol with BFD and will receive forwarding path detection failure messages from BFD.

                                      BFD for EIGRP is not supported on the Cisco 12000 series routers for Cisco IOS Releases 12.0(31)S, 12.0(32)S, 12.4(4)T, and 12.2(33)SRA.

                                      BFD—BFD Hardware Offload Support

                                      15.1(2)S

                                      15.1(1)SG

                                      This feature supports offloading BFD sessions to ES+ line cards on Cisco 7600 series routers. The following command was introduced or modified: show bfd neighbors .

                                      BFD Multihop

                                      15.1(3)S

                                      This feature supports multihop BFD for IPv4 and IPv6 addresses. The following commands were introduced or modified: authentication, bfd map, bfd-template, interval, show bfd neighbors, show bfd neighbor drops.

                                      BFD—Static Route Support

                                      12.2(33)SRC

                                      15.0(1)M

                                      15.0(1)S

                                      15.0(1)SY

                                      15.1(2)S

                                      15.1(1)SG

                                      Unlike dynamic routing protocols, such as OSPF and BGP, static routing has no method of peer discovery. Therefore, when BFD is configured, the reachability of the gateway is completely dependent on the state of the BFD session to the specified neighbor. Unless the BFD session is up, the gateway for the static route is considered unreachable, and therefore the affected routes will not be installed in the appropriate RIB.

                                      A single BFD session can be used by an IPv4 static client to track the reachability of next hops through a specific interface. A BFD group can be assigned for a set of BFD-tracked static routes.

                                      The following commands were introduced or modified: ip route static bfd and show ip static route bfd.

                                      BFD Support for IP Tunnel (GRE, with IP address)

                                      15.1(1)SY

                                      This feature supports BFD forwarding on point-to-point IPv4, IPv6, and GRE tunnels.

                                      The following commands were introduced or modified: bfd .

                                      BFD Support over Port Channel

                                      15.1(1)SY

                                      This feature supports configuring BFD timers on port channel interface.

                                      The following commands were introduced or modified: bfd .

                                      BFD—VRF Support

                                      12.2(33)SRC

                                      15.0(1)M

                                      15.0(1)S

                                      15.1(1)SY

                                      The BFD feature support is extended to be VPN Routing and Forwarding (VRF) aware to provide fast detection of routing protocol failures between provider edge (PE) and customer edge (CE) devices.

                                      BFD—WAN Interface Support

                                      12.2(33)SRC

                                      15.0(1)M

                                      15.0(1)S

                                      The BFD feature is supported on nonbroadcast media interfaces including ATM, POS, serial, and VLAN interfaces. BFD support also extends to ATM, FR, POS, and serial subinterfaces.

                                      The bfd interval command must be configured on the interface to initiate BFD monitoring.

                                      Bidirectional Forwarding Detection (standard implementation, Version 1)

                                      12.0(31)S

                                      12.0(32)S

                                      12.2(33)SRB

                                      12.2(33)SRC

                                      12.2(18)SXE

                                      12.2(33)SXH

                                      12.4(9)T

                                      12.4(11)T

                                      12.4(15)T

                                      15.0(1)S

                                      This document describes how to enable the Bidirectional Forwarding Detection (BFD) protocol. BFD is a detection protocol designed to provide fast forwarding path failure detection times for all media types, encapsulations, topologies, and routing protocols. In addition to fast forwarding path failure detection, BFD provides a consistent failure detection method for network administrators. Because the network administrator can use BFD to detect forwarding path failures at a uniform rate, rather than the variable rates for different routing protocol hello mechanisms, network profiling and planning will be easier, and reconvergence time will be consistent and predictable.

                                      In Release 12.0(31)S, support was added for the Cisco 12000 series Internet router.

                                      In Release 12.0(32)S, support was added for the Cisco 10720 Internet router and IP Services Engine (Engine 3) and Engine 5 shared port adapters (SPAs) and SPA interface processors (SIPs) on the Cisco 12000 series Internet router.

                                      HSRP Support for BFD

                                      12.2(33)SRC

                                      12.4(11)T

                                      12.4(15)T

                                      In Release 12.4(11)T, support for HSRP was added.

                                      In Release 12.4(15)T, BFD is supported on the Integrated Services Router (ISR) family of Cisco routers, for example, the Cisco 3800 ISR series routers.

                                      In Release 12.2(33)SRC, the number of BFD sessions that can be created has been increased, BFD support has been extended to ATM, FR, POS, and serial subinterfaces, the BFD feature has been extended to be VRF-aware, BFD sessions are placed in an “Admin Down” state during a planned switchover, and BFD support has been extended to static routing.

                                      IS-IS Support for BFD over IPv4

                                      12.0(31)S

                                      12.2(18)SXE

                                      12.2(33)SRA

                                      12.4(4)T

                                      15.0(1)S

                                      BFD support for OSPF can be configured globally on all interfaces or configured selectively on one or more interfaces. When BFD support is configured with IS-IS as a registered protocol with BFD, IS-IS receives forwarding path detection failure messages from BFD.

                                      OSPF Support for BFD over IPv4

                                      12.0(31)S

                                      12.2(18)SXE

                                      12.2(33)SRA

                                      12.4(4)T

                                      15.0(1)S

                                      15.1(1)SG

                                      BFD support for OSPF can be configured globally on all interfaces or configured selectively on one or more interfaces. When BFD support is configured with OSPF as a registered protocol with BFD, OSPF receives forwarding path detection failure messages from BFD.

                                      SSO—BFD

                                      12.2(33)SRE

                                      12.2(33)SXI2

                                      12.2(33)XNE

                                      15.0(1)S

                                      15.1(1)SG

                                      Network deployments that use dual RP routers and switches have a graceful restart mechanism to protect forwarding states across a switchover. This feature enables BFD to maintain sessions in a up state across switchovers.

                                      SSO—BFD (Admin Down)

                                      12.2(33)SRC

                                      15.0(1)S

                                      To support SSO, BFD sessions are placed in an “Admin Down” state during a planned switchover. The BFD configuration is synched from the active to standby processor, and all BFD clients re-register with the BFD process on the standby processor.