Step 1
| When you first start the program, configure the global parameters
to control system-wide settings:
Connect a console terminal to the console port on the I/O
controller, and then boot the router from Flash memory.
After booting, the following information appears after about 30
seconds. When you see this information, you have successfully booted your
router:
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (UBR7200-IK1S-M), Version 12.1(10)EC
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Fri 24-Nov-01 12:59 by yiyan
Image text-base: 0x60008950, data-base: 0x61478000
Compliance with U.S. Export Laws and Regulations - Encryption
This product performs encryption and is regulated for export
by the U.S. Government.
This product is not authorized for use by persons located
outside the United States and Canada that do not have prior
approval from Cisco Systems, Inc. or the U.S. Government.
This product may not be exported outside the U.S. and Canada
either by physical or electronic means without PRIOR approval
of Cisco Systems, Inc. or the U.S. Government.
Persons outside the U.S. and Canada may not re-export, resell,
or transfer this product by either physical or electronic means
without prior approval of Cisco Systems, Inc. or the U.S.
Government.
Cisco uBR7246VXR (NPE300) processor (revision D) with 253952K/40960K bytes
of memory.
Processor board ID SAB0433019F
R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3 Cache
6 slot VXR midplane, Version 2.0
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
4 Serial network interface(s)
4 Cable Modem network interface(s)
125K bytes of non-volatile configuration memory.
125440K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
4096K bytes of Flash internal SIMM (Sector size 256K).
cable submgmt default active
Press RETURN to get started!
Note
| The first two sections of the configuration script, the banner
and the installed hardware, appear only at initial system startup. On
subsequent uses of the
Setup facility , the script begins with the following
prompt.
|
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
|
Step 4
| Enter the
enable secret password, the
enable password, and the
virtual terminal password.
The enable secret password is a one-way cryptographic secret
password used instead of the enable password when it exists. The enable
password is used when there is no enable secret password and when using older
software and some boot images.
Enter enable secret: ******
Enter enable password: ******
Enter virtual terminal password: ******
|
Step 6
| In all cases, you will use IP routing. When you are using IP
routing, select an interior routing protocol. You can specify one of only two
interior routing protocols to operate on your system using the Setup facility,
either In terior Gateway Routing Protocol (IGRP) or Routing Information
Protocol (RIP).
To configure IP routing, enter
yes (the default) or press
Return, and then select an interior routing
protocol:
Configure IP? [yes]:
Configure IGRP routing? [yes]:
Your IGRP autonomous system number [1]: 15
|
Step 7
| Configure your line card interface parameters. The following
example shows how an 8-port Ethernet line card is installed in line card slot
3. The Setup facility determines the status of all interfaces.
To configure each active interface port for IP, enter
yes (the default) or press
Return . For all inactive ports, the default
is no. You can press
Return to accept the default.
Configuring interface Ethernet 1/0:
Is this interface in use? [yes]:
Configure IP on this interface? [yes]:
IP address for this interface [19.2.22.4]:
Number of bits in subnet field [8]:
Class A network is 19.0.0.0, 8 subnet bits; mask is /16
Configuring interface Ethernet1/1:
Is this interface in use? [no]:
Configuring interface Ethernet1/2:
Is this interface in use? [no]:
Configuring interface Ethernet1/3:
Is this interface in use? [no]:
Configuring interface Ethernet1/4:
Is this interface in use? [no]:
Configuring interface Ethernet1/5:
Is this interface in use? [no]:
Configuring interface Ethernet1/6:
Is this interface in use? [no]:
Configuring interface Ethernet1/7:
Is this interface in use? [no]:
|
Step 8
| Configure your cable interface. The following example shows a
Cisco CMTS with cable interface. The Setup facility, for the most part,
determines the status of all interfaces.
To configure each active interface port, enter
yes (the default) or press
Return . For all inactive ports, the default
is no. You can press
Return to accept the default.
Configuring interface cable 5/0:
Is this interface in use? [yes]:
Configure this interface? [yes]:
IP address for this interface [19.2.22.5]:
Number of bits in subnet field [8]:
Class A network is 19.0.0.0, 8 subnet bits; mask is /16
Configuring interface cable 1/1:
Is this interface in use? [yes]:
Configure this interface? [yes]:
IP address for this interface [19.2.22.6]:
Number of bits in subnet field [8]:
Class A network is 19.0.0.0, 8 subnet bits; mask is /16
The configuration program displays the newly created command
interface script:
The following command script was created:
hostname router
enable secret 5 $1$f0fc$A38P/KN/9yD3sEKSt6hKQ/
enable password betty
line vty 0 4
password wilma
snmp-server community public
!
ip routing
!
interface cable 5/0
ip address 19.2.22.5 255.255.0.0
router igrp 15
network 19.0.0.0
!
end
|