Cisco Virtual Network Management Center CLI Configuration Guide, Release 1.0.1 - Managing the Device Profile [Cisco Virtual Network Management Center]

Table Of Contents

Managing the Device Profile

Creating a DNS Server Host Name

Creating an NTP Server Host Name

Deleting a DNS Server Host Name

Creating the Domain Name

Deleting an NTP Server Host Name

Setting the Domain Name

Displaying the Device Profile

Setting the Core File Policy

Setting the Fault Policy

Setting the Log Policy

Setting the Syslog Policy

Setting the Timezone

Displaying the DNS Server

Displaying the Domain Name

Displaying the NTP Server

Managing the Device Profile

This chapter provides procedures for managing the device profile.

This chapter includes the following sections:

•Creating a DNS Server Host Name

•Creating an NTP Server Host Name

•Deleting a DNS Server Host Name

•Deleting an NTP Server Host Name

•Displaying the Device Profile

•Setting the Core File Policy

•Setting the Fault Policy

•Setting the Log Policy

•Setting the Syslog Policy

•Setting the Timezone

•Displaying the DNS Server

•Displaying the Domain Name

•Displaying the NTP Server

Creating a DNS Server Host Name

You can create a Domain Name Server (DNS) hostname.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. create dns <ip-address>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
create dns
Example
vnmc(policy-mgr) /org/deviceprofile # create dns 209.165.200.225
Creates a DNS host name.

Specify the host name as an IP address in the format a.b.c.d.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to create a DNS host name:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # create dns 209.165.200.225
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Creating an NTP Server Host Name

You can create a network time protocol (NTP) server hostname.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. create ntp-server <server-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
create ntp-server
Example
vnmc(policy-mgr) /org/deviceprofile # 
create ntp-server networkTime
Creates a NTP server host name.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to create a NTP server host name:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # create ntp-server networkTime
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Deleting a DNS Server Host Name

You can delete a Domain Name Server (DNS) hostname.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. delete dns <ip-address>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile DP0
Example
vnmc(policy-mgr) /org # scope deviceprofile
Places you in device profile mode.
Step 4
delete dns
Example
vnmc(policy-mgr) /org/deviceprofile # delete dns 209.165.200.225
Deletes a DNS host name.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to delete a DNS server host name:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # delete dns 209.165.200.225
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Creating the Domain Name

You can create the domain name.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. scope domain-name <domain-name>

5. set domain <domain-name>

6. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
scope domain-name
Example
vnmc(policy-mgr) /org/deviceprofile # scope domain-name DN0
Places you in domain mode.
Step 5
set domain
Example
vnmc(policy-mgr) /org/deviceprofile # set domain EaTest
Creates the domain name.
Step 6
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to create the domain name:
VNMC-Tech-Docs# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # scope domain-name DN0
vnmc(policy-mgr) /org/deviceprofile/domain-name # set domain EaTest
vnmc(policy-mgr) /org/deviceprofile/domain-name* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile/domain-name* # 
Deleting an NTP Server Host Name

You can delete a network time protocol (NTP) server hostname.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. delete ntp-server <server-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
delete ntp-server
Example
vnmc(policy-mgr) /org/deviceprofile # delete ntp-server networkTime
Deletes a NTP server host name.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to delete a NTP server host name:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # delete ntp-server networkTime
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Setting the Domain Name

You can set the domain name.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. scope domain-name <domain-name>

5. set domain <domain-name>

6. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
scope domain-name
Example
vnmc(policy-mgr) /org/deviceprofile # scope domain-name DN0
Places you in domain name mode.
Step 5
set domain
Example
vnmc(policy-mgr) /org/deviceprofile/domain-name # set domain testOne
Sets the domain name.
Step 6
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to set the domain name:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # scope domain-name DN0
vnmc(policy-mgr) /org/deviceprofile/domain-name # set domain testOne
vnmc(policy-mgr) /org/deviceprofile/domain-name* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile/domain-name # 
Displaying the Device Profile

You can display the device profile.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. show deviceprofile

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
show deviceprofile
Example
vnmc(policy-mgr) /org # show deviceprofile
Displays the device profile.
EXAMPLES

This example shows how to display the device profile:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # show deviceprofile
Name: default
Core File Policy:
Fault Policy: default
Log File Policy: default
Syslog Policy:
vnmc(policy-mgr) /org # 
Setting the Core File Policy

You can set the core file policy.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. set corefile <policy-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
set corefile
Example
vnmc(policy-mgr) /org/deviceprofile # set corefile EaCorePA13
Sets the core file policy.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to set the core file policy:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile default
vnmc(policy-mgr) /org/deviceprofile # set corefile EaCorePA13
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Setting the Fault Policy

You can set the fault policy.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. set faultpolicy <policy-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
set faultpolicy
Example
vnmc(policy-mgr) /org/deviceprofile # set faultpolicy EaFaultPA12
Sets the fault policy.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to set the fault policy:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # set faultpolicy EaFaultPA12
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Setting the Log Policy

You can set the log policy.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. set log <policy-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
set log
Example
vnmc(policy-mgr) /org/deviceprofile # set log EaLogPA12
Sets the log policy.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to set the log policy:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # set log EaLogPA12
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Setting the Syslog Policy

You can set the syslog policy.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. set syslog <policy-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
set syslog
Example
vnmc(policy-mgr) /org/deviceprofile # set syslog EaSysPA12
Sets the syslog policy.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to set the syslog policy:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # set syslog EaSysPA12
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Setting the Timezone

You can set the timezone.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. set timezone <zone-name>

5. commit-buffer

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
set timezone
Example
vnmc(policy-mgr) /org/deviceprofile # 
set timezone pacific
Sets the timezone.
Step 5
commit-buffer
Example
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
Commits (saves) the configuration.
EXAMPLES

This example shows how to set the timezone:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # set timezone pacific
vnmc(policy-mgr) /org/deviceprofile* # commit-buffer
vnmc(policy-mgr) /org/deviceprofile # 
Displaying the DNS Server

You can display the DNS server.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. show dns

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
show dns
Example
vnmc(policy-mgr) /org/deviceprofile # show dns
Displays the DNS server.
EXAMPLES

This example shows how to display the DNS server:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
vnmc(policy-mgr)# scope org
vnmc(policy-mgr) /org # scope deviceprofile DP0
vnmc(policy-mgr) /org/deviceprofile # show dns
Domain Name Servers:
    IP Address: 209.165.200.226
vnmc(policy-mgr) /org/deviceprofile # 
Displaying the Domain Name

You can display the domain name.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. show domain-name

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
show domain-name
Example
vnmc(policy-mgr) /org/deviceprofile # show domain-name
Displays the domain name.
EXAMPLES

This example shows how to display the domain name:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
VNMC-Tech-Docs(policy-mgr)# scope org
VNMC-Tech-Docs(policy-mgr) /org # scope deviceprofile DP0
VNMC-Tech-Docs(policy-mgr) /org/deviceprofile # show domain-name
Domain Name:
    Domain
    ------
    Cisco.com
vnmc(policy-mgr) /org/deviceprofile # 
Displaying the NTP Server

You can display the NTP server.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Policy manager

SUMMARY STEPS

1. connect policy-mgr

2. scope org

3. scope deviceprofile <profile-name>

4. show ntp

DETAILED STEPS
Command

Purpose
Step 1
connect policy-mgr
Example:
vnmc# connect policy-mgr
Places you in the policy manager CLI.
Step 2
scope org
Example:
vnmc(policy-mgr)# scope org
Places you in organization mode.
Step 3
scope deviceprofile
Example
vnmc(policy-mgr) /org # scope deviceprofile DP0
Places you in device profile mode.
Step 4
show ntp
Example
vnmc(policy-mgr) /org/deviceprofile # show ntp
Displays the NTP server.
EXAMPLES

This example shows how to display the NTP server:
vnmc# connect policy-mgr
Cisco Virtual Network Management Center
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
VNMC-Tech-Docs(policy-mgr)# scope org
VNMC-Tech-Docs(policy-mgr) /org # scope deviceprofile DP0
VNMC-Tech-Docs(policy-mgr) /org/deviceprofile # show ntp 
NTP Servers:
    Name: EaTest
VNMC-Tech-Docs(policy-mgr) /org/deviceprofile # 