Cisco Virtual Network Management Center CLI Configuration Guide, Release 1.0.1 - Managing Logging [Cisco Virtual Network Management Center]

Managing Logs, Events and Faults

Working With Management Logs

Setting Severity Levels and Log Size

Resetting the Management Log Levels

Saving Management Log Parameters

Displaying Management Logs

Acknowledging Faults

Displaying Audit Logs

Displaying Events

Displaying Faults

Managing Logs, Events and Faults

This chapter provides procedures for managing VNMC management logging.

This chapter includes the following sections:

•Working With Management Logs

•Acknowledging Faults

•Displaying Audit Logs

•Displaying Events

•Displaying Faults

Working With Management Logs

This section includes the following topics:

•Setting Severity Levels and Log Size

•Resetting the Management Log Levels

•Saving Management Log Parameters

•Displaying Management Logs

Setting Severity Levels and Log Size

You can set the severity level and log size.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can also perform the set command in the management controller CLI.

2. scope monitoring

3. scope sysdebug

4. scope mgmt-logging

5. set {all | file | module}

EXAMPLES

This example shows how to assign a critical severity level to all logging files in the resource manager CLI:

vnmc# connect resource-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc(resource-mgr)# scope monitoring

vnmc(resource-mgr) /monitoring # scope sysdebug

vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # set all crit

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging #

Resetting the Management Log Levels

You can reset the management log levels.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can also perform the reset command in the management controller CLI.

2. scope monitoring

3. scope sysdebug

4. scope mgmt-logging

5. reset

EXAMPLES

This example shows how to reset in the resource manager CLI:

vnmc# connect resource-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc(resource-mgr)# scope monitoring

vnmc(resource-mgr) /monitoring # scope sysdebug

vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # reset

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging #

Saving Management Log Parameters

You can save the management log parameters.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can also perform the save command in the management controller CLI.

2. scope monitoring

3. scope sysdebug

4. scope mgmt-logging

5. save

EXAMPLES

This example shows how to save in the resource manager CLI:

vnmc# connect resource-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc(resource-mgr)# scope monitoring

vnmc(resource-mgr) /monitoring # scope sysdebug

vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # save

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging #

Displaying Management Logs

You can display management logs.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can perform the show command in the management controller CLI.

2. scope monitoring

3. scope sysdebug

4. scope mgmt-logging

5. show

EXAMPLES

This example shows how to display all log files in the resorce manager CLI:

vnmc# connect resource-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc(resource-mgr)# scope monitoring

vnmc(resource-mgr) /monitoring # scope sysdebug

vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # show

    Log File Size Limit:         10000000

    Name                  Level  Default Level

    --------------------- ------ -------------

    agdriver              Crit   Debug1

    ape                   Crit   Debug1

    app_sam_cim           Crit   Debug1

    app_sam_dme           Crit   Debug1

    app_sam_ucsmAG        Crit   Debug1

    app_unittest_testsvc  Crit   Debug1

    auth                  Crit   Debug1

    autocond              Crit   Debug1

    bio_stream            Crit   Debug1

    callhome              Crit   Debug1

    catalog               Crit   Debug1

    char_stream           Crit   Debug1

    core_transactor       Crit   Debug1

    core_utils            Crit   Debug1

    doer                  Crit   Debug1

    event_                Crit   Debug1

    event_channel         Crit   Debug1

    exception_handling    Crit   Debug1

    fault                 Crit   Debug1

    filter                Crit   Debug1

    fsm                   Crit   Debug1

    http_client           Crit   Debug1

    log                   Crit   Debug1

    meta                  Crit   Debug1

    method                Crit   Debug1

    mgmt                  Crit   Debug1

    mgmtif                Crit   Debug1

    mit_init              Crit   Debug1

    mo                    Crit   Debug1

    mo_qualifier          Crit   Debug1

    mod_nuova             Crit   Debug1

    net                   Crit   Debug1

    org                   Crit   Debug1

    os                    Crit   Debug1

    pam_proxy             Crit   Debug1

    pool                  Crit   Debug1

    proc_app              Crit   Debug1

    prt                   Crit   Debug1

    sam_extXMLApi_        Crit   Debug1

    sam_sec               Crit   Debug1

    sam_sessionmgrAG      Crit   Debug1

    sam_ucssh             Crit   Debug1

    smbios                Crit   Debug1

    snmp                  Crit   Debug1

    solprot               Crit   Debug1

    stats                 Crit   Debug1

    sysdebug              Crit   Debug1

    top                   Crit   Debug1

    tx                    Crit   Debug1

    xml_parser            Crit   Debug1

vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging #

Acknowledging Faults

You can acknowledge faults.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can perform the acknowledge command in the management controller CLI.

1. scope monitoring

2. acknowledge fault

3. commit-buffer

EXAMPLES

This example shows how to acknowledge a fault in the management controller CLI:

vnmc# scope monitoring

vnmc /monitoring # acknowledge fault 10194

vnmc /monitoring* # commit-buffer

vnmc /monitoring #

Displaying Audit Logs

You can display a list of audit logs.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can perform this show command in the management controller CLI.

2. scope monitoring

3. show audit-logs

EXAMPLES

This example shows how to display a list of audit logs in the policy manager CLI:

vnmc# connect policy-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc(resource-mgr)# scope monitoring

vnmc(policy-mgr) /monitoring # show audit-logs

Audit trail logs:

    Creation Time        User       ID       Action           Description

    -------------------- ---------- -------- ---------------- -----------

    2010-11-29T14:56:29.195

                         admin         10615 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.195

                         admin         10616 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.195

                         admin         10617 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10607 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10608 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10609 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10610 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10611 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10612 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10613 Modification     sysdebug mgmt log

control module

    2010-11-29T14:56:29.194

                         admin         10614 Modification     sysdebug mgmt log

vnmc(policy-mgr) /monitoring #

Displaying Events

You can display a list of events.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can perform this show command in the management controller CLI.

2. scope monitoring

3. show events

EXAMPLES

This example shows how to display a list of events in the policy manager CLI:

vnmc# connect policy-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc(resource-mgr)# scope monitoring

vnmc(policy-mgr) /monitoring # show event

Creation Time            ID       Code     Description

------------------------ -------- -------- -----------

2010-11-22T12:09:26.369     10161 E4194467 [FSM:END]: Resolve Mgmt Controller Fs

m(FSM:sam:dme:ObserveObservedResolveControllerFsm)

2010-11-22T12:09:26.368     10160 E4194465 [FSM:STAGE:END]: Resolve Mgmt Control

ler FSM Execute(FSM-STAGE:sam:dme:ObserveObservedResolveControllerFsm:Execute)

2010-11-22T12:09:26.367     10158 E4194465 [FSM:STAGE:STALE-SUCCESS]: Resolve Mg

mt Controller FSM Execute(FSM-STAGE:sam:dme:ObserveObservedResolveControllerFsm:

Execute)

2010-11-22T12:09:26.018     10156 E4194465 [FSM:STAGE:ASYNC]: Resolve Mgmt Contr

oller FSM Execute(FSM-STAGE:sam:dme:ObserveObservedResolveControllerFsm:Execute)

2010-11-22T12:09:26.017     10153 E4194447 [FSM:END]: Service Registration Fsm(F

SM:sam:dme:ExtpolEpRegisterFsm)

2010-11-22T12:09:26.017     10154 E4194464 [FSM:BEGIN]: Resolve Mgmt Controller

Fsm(FSM:sam:dme:ObserveObservedResolveControllerFsm)

2010-11-22T12:09:26.017     10155 E4194464 [FSM:STAGE:END]: (FSM-STAGE:sam:dme:O

bserveObservedResolveControllerFsm:begin)

2010-11-22T12:09:26.014     10148 E4194445 [FSM:STAGE:END]: Register FSM Execute

(FSM-STAGE:sam:dme:ExtpolEpRegisterFsm:Execute)

2010-11-22T12:09:25.991     10144 E4194445 [FSM:STAGE:STALE-SUCCESS]: Register F

SM Execute(FSM-STAGE:sam:dme:ExtpolEpRegisterFsm:Execute)

2010-11-22T12:09:25.558     10143 E4194445 [FSM:STAGE:ASYNC]: Register FSM Execu

te(FSM-STAGE:sam:dme:ExtpolEpRegisterFsm:Execute)

2010-11-22T12:09:25.557     10141 E4194444 [FSM:BEGIN]: Service Registration Fsm

(FSM:sam:dme:ExtpolEpRegisterFsm)

2010-11-22T12:09:25.557     10142 E4194444 [FSM:STAGE:END]: (FSM-STAGE:sam:dme:E

xtpolEpRegisterFsm:begin)

vnmc(policy-mgr) /monitoring #

Displaying Faults

You can display a list of faults.

BEFORE YOU BEGIN

See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI.

CLI

Management controller

Policy manager

Resource manager

Service registry

Virtual machine manager

SUMMARY STEPS

1. (Optional) connect {policy-mgr | resource-mgr | service-reg | vm-mgr}

Note Step 1 is optional. You can perform the show command in the management controller CLI.

2. scope monitoring

3. show fault

EXAMPLES

This example shows how to display a list of faults:

vnmc# connect policy-mgr

Cisco Virtual Network Management Center

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

vnmc# scope monitoring

vnmc /monitoring # show fault

Severity  Code     Last Transition Time     ID       Description

--------- -------- ------------------------ -------- -----------

Critical  F999556  2010-11-24T18:38:17.345     20133 [FSM:FAILED]: internal system 
backup(FSM:sam:dme:MgmtBackupBackup)

Warning   F16516   2010-11-24T18:38:17.344     20131 [FSM:STAGE:FAILED]: internal system 
backup(FSM-STAGE:sam:dme:MgmtBackupBackup:upload)

Warning   F77956   2010-11-24T18:38:17.344     20129 [FSM:STAGE:REMOTE-ERROR]: Result: 
end-point-failed Code: unspecified Message: Permission denied

(sam:dme:MgmtBackupBackup:upload)

vnmc /monitoring #

	Cisco Virtual Network Management Center CLI Configuration Guide, Release 1.0.1
	Managing Logging
Cisco Virtual Network Management Center CLI Configuration Guide, Release 1.0.1 Index Preface Overview Managing VNMC Managing Backups Managing Logging Managing the Device Profile Managing Policies Setting Attributes for Core File, Fault, and Log Policies Setting Attributes for Syslog Policies	Download this chapter Managing Logging Download the complete book PDF (PDF - 1 MB) Feedback Table Of Contents Managing Logs, Events and Faults Working With Management Logs Setting Severity Levels and Log Size Resetting the Management Log Levels Saving Management Log Parameters Displaying Management Logs Acknowledging Faults Displaying Audit Logs Displaying Events Displaying Faults Managing Logs, Events and Faults This chapter provides procedures for managing VNMC management logging. This chapter includes the following sections: •Working With Management Logs •Acknowledging Faults •Displaying Audit Logs •Displaying Events •Displaying Faults Working With Management Logs This section includes the following topics: •Setting Severity Levels and Log Size •Resetting the Management Log Levels •Saving Management Log Parameters •Displaying Management Logs Setting Severity Levels and Log Size You can set the severity level and log size. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can also perform the set command in the management controller CLI. 2. scope monitoring 3. scope sysdebug 4. scope mgmt-logging 5. set {all \| file \| module} EXAMPLES This example shows how to assign a critical severity level to all logging files in the resource manager CLI: vnmc# connect resource-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc(resource-mgr)# scope monitoring vnmc(resource-mgr) /monitoring # scope sysdebug vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # set all crit vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # Resetting the Management Log Levels You can reset the management log levels. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can also perform the reset command in the management controller CLI. 2. scope monitoring 3. scope sysdebug 4. scope mgmt-logging 5. reset EXAMPLES This example shows how to reset in the resource manager CLI: vnmc# connect resource-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc(resource-mgr)# scope monitoring vnmc(resource-mgr) /monitoring # scope sysdebug vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # reset vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # Saving Management Log Parameters You can save the management log parameters. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can also perform the save command in the management controller CLI. 2. scope monitoring 3. scope sysdebug 4. scope mgmt-logging 5. save EXAMPLES This example shows how to save in the resource manager CLI: vnmc# connect resource-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc(resource-mgr)# scope monitoring vnmc(resource-mgr) /monitoring # scope sysdebug vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # save vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # Displaying Management Logs You can display management logs. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can perform the show command in the management controller CLI. 2. scope monitoring 3. scope sysdebug 4. scope mgmt-logging 5. show EXAMPLES This example shows how to display all log files in the resorce manager CLI: vnmc# connect resource-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc(resource-mgr)# scope monitoring vnmc(resource-mgr) /monitoring # scope sysdebug vnmc(resource-mgr) /monitoring/sysdebug # scope mgmt-logging vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # show Log File Size Limit: 10000000 Name Level Default Level --------------------- ------ ------------- agdriver Crit Debug1 ape Crit Debug1 app_sam_cim Crit Debug1 app_sam_dme Crit Debug1 app_sam_ucsmAG Crit Debug1 app_unittest_testsvc Crit Debug1 auth Crit Debug1 autocond Crit Debug1 bio_stream Crit Debug1 callhome Crit Debug1 catalog Crit Debug1 char_stream Crit Debug1 core_transactor Crit Debug1 core_utils Crit Debug1 doer Crit Debug1 event_ Crit Debug1 event_channel Crit Debug1 exception_handling Crit Debug1 fault Crit Debug1 filter Crit Debug1 fsm Crit Debug1 http_client Crit Debug1 log Crit Debug1 meta Crit Debug1 method Crit Debug1 mgmt Crit Debug1 mgmtif Crit Debug1 mit_init Crit Debug1 mo Crit Debug1 mo_qualifier Crit Debug1 mod_nuova Crit Debug1 net Crit Debug1 org Crit Debug1 os Crit Debug1 pam_proxy Crit Debug1 pool Crit Debug1 proc_app Crit Debug1 prt Crit Debug1 sam_extXMLApi_ Crit Debug1 sam_sec Crit Debug1 sam_sessionmgrAG Crit Debug1 sam_ucssh Crit Debug1 smbios Crit Debug1 snmp Crit Debug1 solprot Crit Debug1 stats Crit Debug1 sysdebug Crit Debug1 top Crit Debug1 tx Crit Debug1 xml_parser Crit Debug1 vnmc(resource-mgr) /monitoring/sysdebug/mgmt-logging # Acknowledging Faults You can acknowledge faults. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can perform the acknowledge command in the management controller CLI. 1. scope monitoring 2. acknowledge fault 3. commit-buffer EXAMPLES This example shows how to acknowledge a fault in the management controller CLI: vnmc# scope monitoring vnmc /monitoring # acknowledge fault 10194 vnmc /monitoring* # commit-buffer vnmc /monitoring # Displaying Audit Logs You can display a list of audit logs. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can perform this show command in the management controller CLI. 2. scope monitoring 3. show audit-logs EXAMPLES This example shows how to display a list of audit logs in the policy manager CLI: vnmc# connect policy-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc(resource-mgr)# scope monitoring vnmc(policy-mgr) /monitoring # show audit-logs Audit trail logs: Creation Time User ID Action Description -------------------- ---------- -------- ---------------- ----------- 2010-11-29T14:56:29.195 admin 10615 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.195 admin 10616 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.195 admin 10617 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10607 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10608 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10609 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10610 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10611 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10612 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10613 Modification sysdebug mgmt log control module 2010-11-29T14:56:29.194 admin 10614 Modification sysdebug mgmt log vnmc(policy-mgr) /monitoring # Displaying Events You can display a list of events. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can perform this show command in the management controller CLI. 2. scope monitoring 3. show events EXAMPLES This example shows how to display a list of events in the policy manager CLI: vnmc# connect policy-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc(resource-mgr)# scope monitoring vnmc(policy-mgr) /monitoring # show event Creation Time ID Code Description ------------------------ -------- -------- ----------- 2010-11-22T12:09:26.369 10161 E4194467 [FSM:END]: Resolve Mgmt Controller Fs m(FSM:sam:dme:ObserveObservedResolveControllerFsm) 2010-11-22T12:09:26.368 10160 E4194465 [FSM:STAGE:END]: Resolve Mgmt Control ler FSM Execute(FSM-STAGE:sam:dme:ObserveObservedResolveControllerFsm:Execute) 2010-11-22T12:09:26.367 10158 E4194465 [FSM:STAGE:STALE-SUCCESS]: Resolve Mg mt Controller FSM Execute(FSM-STAGE:sam:dme:ObserveObservedResolveControllerFsm: Execute) 2010-11-22T12:09:26.018 10156 E4194465 [FSM:STAGE:ASYNC]: Resolve Mgmt Contr oller FSM Execute(FSM-STAGE:sam:dme:ObserveObservedResolveControllerFsm:Execute) 2010-11-22T12:09:26.017 10153 E4194447 [FSM:END]: Service Registration Fsm(F SM:sam:dme:ExtpolEpRegisterFsm) 2010-11-22T12:09:26.017 10154 E4194464 [FSM:BEGIN]: Resolve Mgmt Controller Fsm(FSM:sam:dme:ObserveObservedResolveControllerFsm) 2010-11-22T12:09:26.017 10155 E4194464 [FSM:STAGE:END]: (FSM-STAGE:sam:dme:O bserveObservedResolveControllerFsm:begin) 2010-11-22T12:09:26.014 10148 E4194445 [FSM:STAGE:END]: Register FSM Execute (FSM-STAGE:sam:dme:ExtpolEpRegisterFsm:Execute) 2010-11-22T12:09:25.991 10144 E4194445 [FSM:STAGE:STALE-SUCCESS]: Register F SM Execute(FSM-STAGE:sam:dme:ExtpolEpRegisterFsm:Execute) 2010-11-22T12:09:25.558 10143 E4194445 [FSM:STAGE:ASYNC]: Register FSM Execu te(FSM-STAGE:sam:dme:ExtpolEpRegisterFsm:Execute) 2010-11-22T12:09:25.557 10141 E4194444 [FSM:BEGIN]: Service Registration Fsm (FSM:sam:dme:ExtpolEpRegisterFsm) 2010-11-22T12:09:25.557 10142 E4194444 [FSM:STAGE:END]: (FSM-STAGE:sam:dme:E xtpolEpRegisterFsm:begin) vnmc(policy-mgr) /monitoring # Displaying Faults You can display a list of faults. BEFORE YOU BEGIN See VNMC CLIs Basic Commands, page 1-5 for basic information about the VNMC CLI. CLI Management controller Policy manager Resource manager Service registry Virtual machine manager SUMMARY STEPS 1. (Optional) connect {policy-mgr \| resource-mgr \| service-reg \| vm-mgr} Note Step 1 is optional. You can perform the show command in the management controller CLI. 2. scope monitoring 3. show fault EXAMPLES This example shows how to display a list of faults: vnmc# connect policy-mgr Cisco Virtual Network Management Center TAC support: http://www.cisco.com/tac Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved. The copyrights to certain works contained in this software are owned by other third parties and used and distributed under license. Certain components of this software are licensed under the GNU General Public License (GPL) version 2.0 or the GNU Lesser General Public License (LGPL) Version 2.1. A copy of each such license is available at http://www.opensource.org/licenses/gpl-2.0.php and http://www.opensource.org/licenses/lgpl-2.1.php vnmc# scope monitoring vnmc /monitoring # show fault Severity Code Last Transition Time ID Description --------- -------- ------------------------ -------- ----------- Critical F999556 2010-11-24T18:38:17.345 20133 [FSM:FAILED]: internal system backup(FSM:sam:dme:MgmtBackupBackup) Warning F16516 2010-11-24T18:38:17.344 20131 [FSM:STAGE:FAILED]: internal system backup(FSM-STAGE:sam:dme:MgmtBackupBackup:upload) Warning F77956 2010-11-24T18:38:17.344 20129 [FSM:STAGE:REMOTE-ERROR]: Result: end-point-failed Code: unspecified Message: Permission denied (sam:dme:MgmtBackupBackup:upload) vnmc /monitoring #
	Terms & Conditions \| Privacy Statement \| Cookie Policy \| Trademarks

Table Of Contents

Managing Logs, Events and Faults

Working With Management Logs

Setting Severity Levels and Log Size

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Resetting the Management Log Levels

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Saving Management Log Parameters

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Displaying Management Logs

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Acknowledging Faults

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Displaying Audit Logs

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Displaying Events

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES

Displaying Faults

BEFORE YOU BEGIN

CLI

SUMMARY STEPS

EXAMPLES