在MS-DOS平台上載入Aironet驅動程式

簡介

本文檔介紹如何在基於Microsoft DOS(MS-DOS)的筆記型電腦上安裝Cisco Aironet驅動程式。

必要條件

需求

思科建議您瞭解以下主題：

• 無線LAN(WLAN)技術及術語

• PC硬體主題

• MS-DOS配置命令

採用元件

本文中的資訊係根據以下軟體和硬體版本：

• Aironet PCM 3xx或LMC 3xx客戶端介面卡

• MS-DOS 6.22

• DOS版Aironet驅動程式6.22

慣例

如需文件慣例的詳細資訊，請參閱思科技術提示慣例。

安裝Aironet的DOS驅動程式

完成以下步驟以安裝DOS驅動程式：

1. 透過以下方式建立config.sys檔案：

   DEVICE=A:\DOS\HIMEM.SYS
   DEVICE=A:\DOS\EMM386.EXE X=D000-DFFF FRAME=NONE
   DEVICEHIGH=A:\IBMDSS14.SYS
   DEVICEHIGH=A:\IBMDOSCS.SYS
   DEVICEHIGH=A:\DICRMU01.SYS /MA-D000-D7FF /SH=1 /IX=5,10,11,15
   DEVICE=A:\NET\IFSHLP.SYS
   DEVICE=A:\DOS\RAMDRIVE.SYS 2048 /e
   DEVICE=A:\DOS\ANSI.SYS
   DOS=HIGH,UMB
   FILES=40
   BUFFERS=30
   LASTDRIVE=Z
   SHELL=COMMAND.COM /e:512 /p

   IBMDSS14.SYS、IBMDOSCS.SYS和DICRMU01.SYS檔案是適用於典型IBM筆記型電腦的PCMCIA卡和套接字服務。根據情況替換筆記型電腦製造商提供的相應檔案。

2. 根據個人需求自定義所包含的cscpkt.ini檔案：

   [CSCPKT]
           ;Initialization file for Infrastructure operating mode
   
           ; NOTE: The following are some keyword parameters that may
           ;be modified.  Any commented or omitted keyword parameter
           ;assumes the factory default.  For most situations the
           ;factory defaults will be appropriate.  In situations where
           ;the factory default needs to be modified, uncomment or add the
           ;keyword parameter line and set the appropriate keyword value.
   
           SSID="network_ssid"     ;Must match Access Point setting
           ;FragThreshold=2312     ;Packet size to start fragmenting
           ;RTSThreshold=2312      ;Packet size to start sending RTS/CTS
           ;DataRate1=0x02         ;(1)   Mbps supported data bit rate
           ;DataRate2=0x04         ;(2)   Mbps supported data bit rate
           ;DataRate3=0x0B         ;(5.5) Mbps supported data bit rate
           ;DataRate4=0x16         ;(11)  Mbps supported data bit rate
           ;RefreshInterval=10000  ;Inactivity time to check association
           ;PowerSaveMode="CAM"    ;Constant Awake Mode
           ;MaxPowerSave="OFF"     ;Maximum power save mode
           NodeName="CiscoPC"      ;Descriptive station name
           AuthType="WEPOPEN"      ;WEP with open authentication
   
           ;The adapter needs 32 16-bit I/O ports, and 1 non-sharable IRQ.
           ;The following lines should be uncommented and the appropriate
           ;values set in the following scenarios:
           ; 1) PCMCIA mode: Override the I/O port base and/or IRQ
           ;                 assigned by PCMCIA card services.
           ; 2) PCMCIA mode: PCMCIA card services is not being used.
           ; 3) ISA mode: Override the I/O port base and/or IRQ assigned
           ;              by Plug and Play.
           ; 4) ISA mode: Non-Plug and Play operation.
           
           ;PortBase=0x140
           ;IRQ=5
   
           ;If the PCMCIA interface is being used without PCMCIA card services,
           ;uncomment the following lines and set the appropriate values.
   
           Memory=0xD000
           Socket=0
   
           ;If the PCMCIA interface is not being used, set the appropriate
           ;value of "ISA" or "PCI".
   
           BusType="PCMCIA"

3. 啟動電腦以載入上述config.sys檔案。

4. 發出以下命令：

   a:>wepdos -365 -tx1 12345678901234567890123456
   

   setting key 1 to 12345678901234567890123456
   setting transmit key index to 1

5. 發出以下命令：

   a:>cscpkt 0x65
   

   Cisco Wireless Packet Driver , version 2.04
   (c) Copyright 2000 Cisco System , Inc.
   All rights Reserved
   Card recognized as a radio in socket 00
   Driver Resources --> IO ports 0400-043F IRQ :03
   350 series Firmware 4.25.30
   Mac Address 00:09:7c:31:87:32
   

相關資訊

• Cisco Aironet無線區域網客戶端介面卡配置指南
• 思科無線產品
• Cisco Aironet Windows客戶端常見問題
• 技術支援與文件 - Cisco Systems