在9800 WLC上配置离线（气隙）许可

简介

本文档介绍如何在Catalyst 9800无线局域网控制器(WLC)上配置离线（气隙）许可。

先决条件

要求

建议了解9800 WLC和CSSM（思科智能软件管理器）门户的基本操作。

使用的组件

本文档中的信息基于以下软件和硬件版本，但适用于17.3之后的所有版本：

• 虚拟9800-CL WLC版本17.9.5

本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始（默认）配置。如果您的网络处于活动状态，请确保您了解所有命令的潜在影响。

配置

网络图

配置

步骤1.在WLC上

1.将许可连接模式设置为AirGap，并将AirGap功能设置为Enabled:

The CLI equivalent is:

9800-17-09-05(config)#license smart transport off

2.从WLC导出RUM报告。这会将您当前的许可证使用量保存到文件：

9800-17-09-05#license smart save usage all file bootflash:rum.txt

步骤2.在CSSM上

1.登录您的CSSM帐户。

2.依次导航至Reports选项卡和Usage Data Files。单击Usage Data Files:

3.单击Browse，然后选择从WLC获取的RUM报告。单击Upload Data:

4.将RUM报告上传到CSSM后，Download按钮将显示在Acknowledgement列下。单击Download:

步骤3.在WLC上

在WLC上导入ACK:

9800-17-09-05#license smart import bootflash:ACK_rum.txt
Import Data Successful

注意：重置许可证工厂后，必须至少等待1小时生成RUM报告。

验证

应用上述配置步骤后，WLC将出现在CSSM上的Inventory > Product Instances下。

如果注册了HA对中的活动WLC，则活动WLC和备用WLC都显示在CSSM上的Product Instances选项卡下。

成功配置的WLC的输出示例：

------------------ show license status ------------------


Utility:
Status: DISABLED

Smart Licensing Using Policy:
Status: ENABLED

Account Information:
Smart Account:  As of Feb 29 15:24:40 2024 UTC
Virtual Account: 

Data Privacy:
Sending Hostname: yes
Callhome hostname privacy: DISABLED
Smart Licensing hostname privacy: DISABLED
Version privacy: DISABLED

Transport:
Type: Transport Off

Policy:
Policy in use: Merged from multiple sources.
Reporting ACK required: yes (CISCO default)
Unenforced/Non-Export Perpetual Attributes:
First report requirement (days): 365 (CISCO default)
Reporting frequency (days): 0 (CISCO default)
Report on change (days): 90 (CISCO default)
Unenforced/Non-Export Subscription Attributes:
First report requirement (days): 90 (CISCO default)
Reporting frequency (days): 90 (CISCO default)
Report on change (days): 90 (CISCO default)
Enforced (Perpetual/Subscription) License Attributes:
First report requirement (days): 0 (CISCO default)
Reporting frequency (days): 0 (CISCO default)
Report on change (days): 0 (CISCO default)
Export (Perpetual/Subscription) License Attributes:
First report requirement (days): 0 (CISCO default)
Reporting frequency (days): 0 (CISCO default)
Report on change (days): 0 (CISCO default)

Miscellaneous:
Custom Id: 

Usage Reporting:
Last ACK received: Feb 29 15:27:53 2024 UTC
Next ACK deadline: May 29 15:27:54 2024 UTC
Reporting push interval: 30 days
Next ACK push check: 
Next report push: Mar 30 15:27:54 2024 UTC
Last report push: Feb 29 15:27:54 2024 UTC
Last report file write: 

Trust Code Installed:
Active: PID:C9800-CL-K9,SN:
INSTALLED on Feb 29 15:27:53 2024 UTC
Standby: PID:C9800-CL-K9,SN:
INSTALLED on Feb 29 15:27:53 2024 UTC

故障排除

如果RUM上传到CSSM门户失败，可能是因为WLC已通过门户上的直接连接注册。从CSSM资产中删除设备。然后您可以上传RUM报告。

参考

• 使用SLUP配置许可