Hoe om IC3000 te herstellen van console

Inleiding

Dit document beschrijft hoe de IC3000 met het gebruik van de console te herstellen.

Hoe om IC3000 te herstellen van console

In bepaalde gevallen wordt de IC3000 onopstartbaar en zit hij vast in rommon> terwijl hij niet kan opstarten.

Wanneer dit probleem zich voordoet, kan de seriële/subconsole deze uitvoer weergeven:

autoboot: Restarting the system.

Rom image verified correctly

Cisco Systems ROMMON, Version 1.0.0(IC3000), RELEASE SOFTWARE
Copyright (c) 1994-2018  by Cisco Systems, Inc.
Compiled Thu 09/06/2018 11:38:52.09 by builders

Current image running: Boot ROM1
Last reset cause: LocalSoft
DIMM Slot 0 : Present

Platform IC3000-2C2F-K9 with 8192 Mbytes of main memory
MAC Address: 00:00:00:00:00:00

Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.

Warning: filesystem is not clean
Directory .boot_string not found
Unable to locate .boot_string directory
Unable to load .boot_string
Attempt autoboot: "boot disk0:"
Warning: filesystem is not clean
Warning: filesystem is not clean
File size is 0x01360000
Located IC3000-K9-1.0.1.SPA
Image size 20316160 inode num 12, bks cnt 4960 blk size 8*512
#######################################################################################################################################################################################################

Signature verification failed for key# 1
Failed to validate digital signature
Signature verification failed for key# 1
Signature verification failed for key# 2
Failed to validate digital signature
LFBFF signature verification failed!!
No kernel found to launch.
boot: cannot determine first file name on device "disk0:/"
autoboot: All boot attempts have failed.
autoboot: Restarting the system.

Wanneer u het opstartproces onderbreekt en probeert om het beeld op te starten, aanwezig op disk0:, kunt u dezelfde uitvoer zien als hierboven en het apparaat is in wezen in een soort bootloop.

Oplossing

Om de IC3000 te herstellen, hebt u deze voorwaarden nodig:

• IP-verbinding met de beheerpoort
• TFTP-server, bereikbaar via het netwerk op de beheerpoort
• IC3000 image, te downloaden op: https://software.cisco.com/download/home/286321941/type/286322235
• Consoleverbinding met de seriële of USB-aansluiting op de IC3000

Met deze stappen kunt u de IC3000 weer in een bruikbare staat krijgen:

1. Download de IC3000 afbeelding van de hierboven verstrekte URL en maak deze beschikbaar op de TFTP-server
2. Sluit aan op de IC3000-console en onderbreek het opstartproces door op ESC te drukken wanneer u dit bericht ziet:
   

   Use BREAK or ESC to interrupt boot.
   Use SPACE to begin boot immediately.

3. Nadat u de normale opstartvolgorde hebt verbroken, krijgt u de rommon> prompt:
   

   rommon 1 >

4. Configureer het IP-adres en de gateway voor de IC3000 op de beheerpoort. Zelfs als geen gateway nodig is, moet een waarde worden ingesteld:
   

   rommon 1 > address 192.168.100.2
   rommon 2 > netmask 255.255.255.0
   rommon 3 > gateway 192.168.100.1

5. Connectiviteit met de TFTP-server testen:
   

   rommon 4 >  ping 192.168.100.1
   Sending 10, 32-byte ICMP Echoes to 192.168.100.1 timeout is 4 seconds
   ?!!!!!!!!!
   Success rate is 90 percent (9/10)

6. Geef het adres van de TFTP-server en de bestandsnaam op die moet worden gedownload:
   

   rommon 5 > server 192.168.100.1
   rommon 6 > file IC3000-K9-1.0.1.SPA

7. Start de download en start de afbeelding op vanaf de TFTP-server:
   

   rommon 7 > tftpdnld
                ADDRESS: 192.168.100.2
                NETMASK: 255.255.255.0
                GATEWAY: 192.168.100.1
                 SERVER: 192.168.100.1
                  IMAGE: IC3000-K9-1.0.1.SPA
                MACADDR: 00:00:00:00:00:00
              VERBOSITY: Progress
                  RETRY: 40
             PKTTIMEOUT: 7200
                BLKSIZE: 1460
               CHECKSUM: Yes
                   PORT: GbE/0
                PHYMODE: Auto Detect
   
   Receiving IC3000-K9-1.0.1.SPA from 192.168.100.1!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
   File reception completed.

 Zodra het beeld met succes is overgebracht, zal IC3000 onmiddellijk van het beeld initialiseren:

File reception completed.
Boot buffer bigbuf=348bd018
Boot image size = 102729968 (0x61f88f0) bytes
[image size]      102729968
[MD5 signaure]    294a052497277c330d6b2159cf37f1ab
LFBFF signature verified.
[    4.446627] sd 2:0:0:0: [sdb] No Caching mode page found
[    4.510305] sd 2:0:0:0: [sdb] Assuming drive cache: write through
INIT: version 2.88 booting
Starting udev
Populating dev cache
INIT: Entering runlevel: 5postinsts/000-monit...
Configuring network interfaces... Setting bridge MAC address to: 00:b8:b3:80:02:c0
done.
Starting system message bus: dbus.
Checking and Mounting BOOT filesystem...
fsck (busybox 1.24.1, 2018-09-13 06:16:00 UTC)
BOOT was not cleanly unmounted, check forced.
BOOT: Inode 12, i_size is 20316160, should be 20447232.  FIXED.
BOOT: Inode 12, i_blocks is 39728, should be 39984.  FIXED.
BOOT: 12/244320 files (0.0% non-contiguous), 22254/976892 blocks
Checking and Mounting BOOT filesystem...Done
Checking GOLDEN filesystem...
fsck (busybox 1.24.1, 2018-09-13 06:16:00 UTC)
GOLDEN was not cleanly unmounted, check forced.
GOLDEN: 12/122160 files (8.3% non-contiguous), 33504/488448 blocks
Checking GOLDEN filesystem...Done
Checking and Mounting SYSTEM filesystem...
fsck (busybox 1.24.1, 2018-09-13 06:16:00 UTC)
SYSTEM: clean, 11/535392 files, 71084/2139136 [   21.111486] fpga_i2c_init_module: FPGA base address = ffffc90001078000
blocks
Checking and Mounting SYSTEM filesystem...Done
Checking and Mounting IOX filesystem...
fsck (busybox 1.24.1, 2018-09-13 06:16:00 UTC)
IOX: clean, 11/5865472 files, 415148/23442851 blocks
Checking and Mounting IOX filesystem...Done
Checking and Mounting LOG filesystem...
fsck (busybox 1.24.1, 2018-09-13 06:16:00 UTC)
LOG: clean, 11/244800 files, 33670/977949 blocks
Checking and Mounting LOG filesystem...Done
0x0000
Authenticating ACT2...ACT2 success

System initializing...
System Type Fiber.
Mounting cgroups...Done
Checking if cgroup is provided by kernel...Yes.
Checking if cgroup is mounted...Yes.
Checking if lssubsys is available...Yes.
Checking if platform defines cgroup parameters...Yes.
Tweaking base cgroup parameters...Done.
Checking if subsystems needed by IOx exist...
Setting up cpu cgroup parameters...
Setting cpu.shares for apphosting.partition to 921...OK
Setting cpu.shares for host to 100...OK
Setting cpu.shares for host/caf to 100...OK
Setting cpuset values for apphosting.partition...OK
Setting up memory cgroup parameters...
Setting memory.limit_in_bytes for apphosting.partition to 6589061529...OK
Setting memory.limit_in_bytes for host to 1647265382...OK
Setting memory.limit_in_bytes for host/caf to 1317812305...OK
OpenBSD Secure Shell server not in use (/etc/ssh/sshd_not_to_be_run)
Starting atd: OK
starting DNS forwarder and DHCP server: dnsmasq... done.
Starting ntpd: done
Starting system log daemon...0
Starting kernel log daemon...0
Network mgmt starting with factory default configuration
User mgmt starting with factory default configuration
Starting konfd: OK
 * Starting virtualization library daemon: libvirtd
no /usr/bin/dnsmasq found; none killed                                   [ ok ]
 * Starting libvirt log management daemon: virtlogd                      [ ok ]
Starting crond: OK
Starting Monit 5.14 daemon with http interface at /var/run/monit.sock


ic3k>