Inleiding
Dit document beschrijft hoe u VLAN Trunk Protocol (VTP) kunt configureren.
Voorwaarden
Vereisten
Er zijn geen specifieke vereisten van toepassing op dit document.
Gebruikte componenten
Dit document is niet beperkt tot specifieke software- en hardware-versies.
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u zorgen dat u de potentiële impact van elke opdracht begrijpt.
Conventies
Raadpleeg de technische tips van Cisco voor meer informatie over documentconventies.
Achtergrondinformatie
VTP vermindert het benodigde beheer in een geschakeld netwerk. Wanneer u een nieuw VLAN op één VTP-server configureert, wordt het VLAN via alle switches in het domein gedistribueerd. Dit vermindert de noodzaak om hetzelfde VLAN overal te configureren. VTP is een bedrijfseigen protocol van Cisco dat beschikbaar is op de meeste Cisco Catalyst Series producten.
Zie VLAN Trunk Protocol (VTP) voor meer informatie over VTP.
Opmerking: Alleen geregistreerde Cisco-gebruikers hebben toegang tot de interne site, tools en documenten.
Configureren
VTP-configuratierichtlijnen
Deze sectie bevat enkele richtlijnen voor de configuratie van VTP in een netwerk.
-
Alle switches hebben dezelfde VTP-domeinnaam, tenzij het netwerkontwerp verschillende VTP-domeinen vereist.
Opmerking: Trunk-onderhandeling werkt niet op meerdere VTP-domeinen. Raadpleeg het gedeelte Gegevensverkeer geblokkeerd tussen VTP-domeinen van VLAN Trunk Protocol (VTP) configureren voor meer informatie.
-
Alle switches in een VTP-domein moeten met dezelfde VTP-versie werken.
-
Alle switches in een VTP-domein hebben hetzelfde VTP-wachtwoord, als die er zijn.
-
Alle VTP Server-switch(s) moeten hetzelfde configuratierevisienummer hebben en het moet ook het hoogste zijn in het domein.
-
Wanneer u een VTP-modus van een switch verplaatst van Transparent naar Server, moeten er VLAN's bestaan die zijn geconfigureerd op de VTP Transparent-switch op de Server-switch.
VTP-configuratie op Catalyst-switches
Deze sectie bevat een aantal basisopdrachten om VTP te configureren op de meestgebruikte Catalyst-switches.
Er waren twee methoden om VTP te configureren, zoals in dit gedeelte wordt getoond. De beschikbaarheid van deze methoden kan afwijken van de versie van Cisco IOS®-software. Methode 1 is bijvoorbeeld niet beschikbaar op nieuwere versies van Cisco IOS, terwijl methode 2 (de globale configuratiemodus) niet beschikbaar is in oudere softwareversies.
-
Methode 1, in VLAN-databasemodus:
Met Cisco IOS-software kunt u de VTP-domeinnaam, de VTP-modus en de VLAN’s configureren in de VLAN-configuratiemodus.
-
Voer in de uitvoeringsmodus de volgende opdracht uit om in de VLAN-configuratiemodus te komen:
Switch#vlan database
!--- Issue this command in privileged EXEC mode,
!--- not in global configuration mode.
Switch(vlan)#
!--- This is VLAN configuration mode.
-
Voer de volgende opdracht uit om de VTP-domeinnaam in te stellen:
Switch(vlan)#vtp domain example
-
Voer de volgende opdracht uit om de VTP-modus in te stellen:
Switch(vlan)#vtp {client | server | transparent}
-
Gebruik de opdracht exit om de VLAN-configuratiemodus af te sluiten.
Opmerking: De opdrachten end en Ctrl-Z werken niet in deze modus.
Switch(vlan)#end
Switch(vlan)#^Z
% Invalid input detected at '^' marker.
Switch(vlan)#
Swtch(vlan)#exit
APPLY completed.
Exiting....
Switch#
-
Methode 2, in globale configuratiemodus:
In de modus Global Configuration kunt u alle VTP-parameters configureren met opdrachten van Cisco IOS-software. Dit zijn de argumenten van de opdracht:
Switch(config)#vtp ?
domain Set the name of the VTP administrative domain.
file Configure IFS filesystem file where VTP configuration is stored.
interface Configure interface as the preferred source for the VTP IP updater
address.
mode Configure VTP device mode
password Set the password for the VTP administrative domain
pruning Set the administrative domain to permit pruning
version Set the administrative domain to VTP version
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vtp domain ?
WORD The ascii name for the VTP administrative domain.
Switch(config)#vtp domain example
Changing VTP domain name from example to example
Switch(config)#vtp mode server
-
Voer de volgende opdrachten uit om de werking en status van het VTP te controleren:
Switch#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : example
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 10.122.190.226 at 0-0-00 00:00:00
Local updater ID is 10.122.190.226 on interface Fa1 (first layer3 interface found)
Feature VLAN:
--------------
VTP Operating Mode : Server
Maximum VLANs supported locally : 1005
Number of existing VLANs : 16
Configuration Revision : 0
MD5 digest : 0x0A 0xF4 0xFD 0xE9 0x99 0xD7 0xAB 0x3F
0x0A 0x64 0x04 0x7C 0x42 0x98 0xD8 0xE5
Switch#
Switch#show vtp counters
VTP statistics:
Summary advertisements received : 0
Subset advertisements received : 0
Request advertisements received : 0
Summary advertisements transmitted : 0
Subset advertisements transmitted : 0
Request advertisements transmitted : 0
Number of config revision errors : 0
Number of config digest errors : 0
Number of V1 summary errors : 0
VTP pruning statistics:
Trunk Join Transmitted Join Received Summary advts received from
non-pruning-capable device
---------------- ---------------- ---------------- ---------------------------
Switch#
Praktische voorbeelden
Voorbeeld 1:
Dit voorbeeld omvat twee Catalyst 4500-switches die zijn verbonden door een TenGigabit Ethernet-koppeling:
-
Switch-A is een nieuwe switch zonder VTP-domeinnaam en zonder VLAN. Switch-C is een switch die momenteel bestaat en wordt uitgevoerd met 16 VLAN's in de VTP-domeintest.
-
In deze voorbeelduitvoer van de opdracht VTP-status weergeven, ziet u dat de VTP-versie standaard op 1 staat. En Switch-A is geschikt voor VTP V2. De switch voert VTP V2 in dit geval echter niet uit. De switch voert VTP V2 alleen uit als de V2-versie is geconfigureerd met de opdracht vtp versie 2. In dit voorbeeld wordt Switch-A geconfigureerd als VTP-client. Het is ook belangrijk om ervoor te zorgen dat de aangesloten switch een Configuration Revision van 0 heeft, of een lagere waarde dan de huidige VTP-server voordat deze op het netwerk wordt aangesloten:
Switch-A#show vtp status
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 0.0.0.0 at 0-0-00 00:00:00
Local updater ID is 10.122.190.226 on interface Fa1 (first layer3 interface found)
Feature VLAN:
--------------
VTP Operating Mode : Server
Maximum VLANs supported locally : 1005
Number of existing VLANs : 5
Configuration Revision : 0
MD5 digest : 0x57 0xCD 0x40 0x65 0x63 0x59 0x47 0xBD
0x56 0x9D 0x4A 0x3E 0xA5 0x69 0x35 0xBC
Switch-A#
Switch-A#
Switch-A#
Switch-A#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/1, Gi1/2, Gi1/4, Gi1/5
Gi1/6, Gi1/7, Gi1/8, Gi1/9
Gi1/10, Gi1/11, Gi1/12, Gi1/13
Gi1/14, Gi1/15, Gi1/16, Gi1/17
Gi1/18, Gi1/19, Gi1/20, Gi1/21
Gi1/22, Gi1/23, Gi1/24, Gi1/25
Gi1/26, Gi1/27, Gi1/28, Gi1/29
Gi1/30, Gi1/31, Gi1/32, Gi1/33
Gi1/34, Gi1/35, Gi1/36, Gi1/37
Gi1/38, Gi1/39, Gi1/40, Gi1/41
Gi1/42, Gi1/43, Gi1/44, Gi1/45
Gi1/46, Gi1/47, Gi1/48, Te3/2
Te3/3, Te3/4, Te3/5, Te3/6
Te3/7, Te3/8
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
Switch-A#
Switch-C#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 503d.e583.3b40
Configuration last modified by 10.122.190.227 at 11-24-22 13:44:22
Local updater ID is 10.122.190.227 on interface Fa1 (first layer3 interface found)
Feature VLAN:
--------------
VTP Operating Mode : Server
Maximum VLANs supported locally : 1005
Number of existing VLANs : 16
Configuration Revision : 4
MD5 digest : 0xCB 0x67 0x2A 0xF1 0x9A 0x8D 0xD3 0x1B
0xA8 0xB3 0x89 0xB2 0x32 0x63 0xA6 0xD0
Switch-C#
Switch-C#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/1, Gi1/2, Gi1/3, Gi1/4
Gi1/5, Gi1/6, Gi1/7, Gi1/8
Gi1/9, Gi1/10, Gi1/11, Gi1/12
Gi1/13, Gi1/14, Gi1/15, Gi1/16
Gi1/17, Gi1/18, Gi1/19, Gi1/20
Gi1/21, Gi1/22, Gi1/23, Gi1/24
Gi1/25, Gi1/26, Gi1/27, Gi1/28
Gi1/29, Gi1/30, Gi1/31, Gi1/32
Gi1/33, Gi1/34, Gi1/35, Gi1/36
Gi1/37, Gi1/38, Gi1/39, Gi1/40
Gi1/41, Gi1/42, Gi1/43, Gi1/44
Gi1/45, Gi1/46, Gi1/47, Gi1/48
Te3/2, Te3/3, Te3/4, Te3/5
Te3/6, Te3/7, Te3/8
2 VLAN0002 active
3 VLAN0003 active
4 VLAN0004 active
5 VLAN0005 active
6 VLAN0006 active
7 VLAN0007 active
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
8 VLAN0008 active
9 VLAN0009 active
10 VLAN0010 active
11 VLAN0011 active
12 VLAN0012 active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
Switch-C#
Switch-A#
Switch-A#configure terminal
Switch-A(config)#vtp version 2
Switch-A(config)#vtp mode client
Setting device to VTP Client mode for VLANS.
Switch-A(config)#end
Switch-A#
Switch-A#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name :
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 10.122.190.226 at 11-25-22 02:34:10
Feature VLAN:
--------------
VTP Operating Mode : Client
Maximum VLANs supported locally : 1005
Number of existing VLANs : 5
Configuration Revision : 1
MD5 digest : 0xD2 0x3F 0x31 0x25 0x6D 0xD1 0x3E 0x27
0x62 0x77 0x7C 0xAF 0x0F 0xF6 0x72 0x02
Switch-A#
-
In dit stadium werd een stam handmatig gecreëerd tussen de twee switches. Zie hoe ze de VTP-pakketuitwisseling synchroniseren en bekijken:
Switch-A#debug sw-vlan vtp events
vtp events debugging is on
Switch-A#debug sw-vlan vtp packets
vtp packets debugging is on
Switch-A#
Switch-A#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch-A(config)#interface tenGigabitEthernet3/2
Switch-A(config-if)#no shut
Switch-A(config-if)#end
Switch-A#
-
Switch-C stuurt een samenvattende advertentie naar Switch-A. Switch-A leert er vervolgens de VTP-domeinnaam uit, zoals getoond in deze voorbeelduitvoer:
!--- On Switch-A:
*Nov 25 02:45:46.580: VTP LOG RUNTIME: switchport trunk mode on Te3/2 has changed
*Nov 25 02:45:46.580: VTP LOG RUNTIME: delaying first flood on new trunk
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Summary packet received in NULL domain state
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Summary packet received, domain = test, rev = 4, followers = 0, length 80, trunk Te3/2
!--- This indicates that Switch-A has received its first summary advertisement.
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Validate TLVs : #tlvs 1, max blk size 4
*Nov 25 02:45:51.100: VTP LOG RUNTIME: Validate TLVs : #00, val 6, len 4
*Nov 25 02:45:51.100:
*Nov 25 02:45:51.100: summary: 02 01 00 04 74 65 73 74 00 00 00 00 00 00 00 00 ....test........
*Nov 25 02:45:51.100: summary: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
*Nov 25 02:45:51.100: summary: 00 00 00 00 00 00 00 04 0A 7A BE E3 32 32 31 31 .........z>c2211
*Nov 25 02:45:51.100: summary: 32 34 31 34 30 31 31 35 8D 07 FE 82 E5 FE 49 AD 24140115..~.e~I-
*Nov 25 02:45:51.100: summary: 1A 6E A5 AB D0 35 C2 CA 00 00 00 01 06 01 00 02 .n%+P5BJ........
*Nov 25 02:45:51.100:
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Transitioning from NULL to test domain
!--- This is where Switch-A gets the VTP domain name.
-
Met de debug ingeschakeld, kunt u zien dat Switch-A een samenvattende advertentie ontvangt zonder volgers. Daarom werkt Switch-A zijn domeinnaam bij en verzendt het advertentieverzoeken om de VLAN-informatie te verkrijgen, zoals weergegeven in deze voorbeelduitvoer:
!--- On Switch-A
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Summary packet rev 4 greater than domain test rev 0
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Domain test currently not in updating state
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Summary packet with followers field zero
*Nov 25 02:45:51.108: VTP LOG RUNTIME: Transmit vtp request, domain test, start value 0
!--- This is where the advertisement request is sent.
-
Switch-C stuurt nog een samenvattende advertentie met volgers naar VLAN 1. De subset-advertentie die alle VLAN's bevat, wordt in deze uitvoer weergegeven. Vervolgens configureert Switch-A alle VLAN's:
!--- On Switch-A:
*Nov 25 02:45:51.595: VTP LOG RUNTIME: Summary packet received, domain = test, rev = 4, followers = 1, length 80, trunk Te3/2
!--- Switch-A has received its second summary advertisement.
!--- This configuration revision is higher than that on Switch-A.
*Nov 25 02:45:51.595: VTP LOG RUNTIME: Validate TLVs : #tlvs 1, max blk size 4
*Nov 25 02:45:51.595: VTP LOG RUNTIME: Validate TLVs : #00, val 6, len 4
*Nov 25 02:45:51.595:
*Nov 25 02:45:51.596: summary: 02 01 01 04 74 65 73 74 00 00 00 00 00 00 00 00 ....test........
*Nov 25 02:45:51.596: summary: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
*Nov 25 02:45:51.596: summary: 00 00 00 00 00 00 00 04 0A 7A BE E3 32 32 31 31 .........z>c2211
*Nov 25 02:45:51.596: summary: 32 34 31 34 30 31 31 35 8D 07 FE 82 E5 FE 49 AD 24140115..~.e~I-
*Nov 25 02:45:51.596: summary: 1A 6E A5 AB D0 35 C2 CA 00 00 00 01 06 01 00 02 .n%+P5BJ........
*Nov 25 02:45:51.596:
*Nov 25 02:45:51.596: VTP LOG RUNTIME: Summary packet rev 4 greater than domain test rev 0
*Nov 25 02:45:51.596: VTP LOG RUNTIME: Domain test currently not in updating state
*Nov 25 02:45:51.596: VTP LOG RUNTIME: pdu len 80, #tlvs 1
*Nov 25 02:45:51.596: VTP LOG RUNTIME: Subset packet received, domain = test, rev = 4, seq = 1, length = 420
!--- Switch-A has received its subset advertisement.
*Nov 25 02:45:51.596: subset: 02 02 01 04 74 65 73 74 00 00 00 00 00 00 00 00 ....test........
*Nov 25 02:45:51.596: subset: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
*Nov 25 02:45:51.596: subset: 00 00 00 00 00 00 00 04 14 00 01 07 00 01 05 DC ...............\
*Nov 25 02:45:51.596: subset: 00 01 86 A1 64 65 66 61 75 6C 74 00 14 00 01 08 ...!default.....
*Nov 25 02:45:51.596: subset: 00 02 05 DC 00 01 86 A2 56 4C 41 4E 30 30 30 32 ...\..."VLAN0002
*Nov 25 02:45:51.596: subset: 14 00 01 08 00 03 05 DC 00 01 86 A3 56 4C 41 4E .......\...#VLAN
*Nov 25 02:45:51.596: subset: 30 30 30 33 14 00 01 08 00 04 05 DC 00 01 86 A4 0003.......\...$
*Nov 25 02:45:51.596: subset: 56 4C 41 4E 30 30 30 34 14 00 01 08 00 05 05 DC VLAN0004.......\
*Nov 25 02:45:51.596: subset: 00 01 86 A5 56 4C 41 4E 30 30 30 35 14 00 01 08 ...%VLAN0005....
*Nov 25 02:45:51.596: subset: 00 06 05 DC 00 01 86 A6 56 4C 41 4E 30 30 30 36 ...\...&VLAN0006
*Nov 25 02:45:51.596: subset: 14 00 01 08 00 07 05 DC 00 01 86 A7 56 4C 41 4E .......\...'VLAN
*Nov 25 02:45:51.596: subset: 30 30 30 37 14 00 01 08 00 08 05 DC 00 01 86 A8 0007.......\...(
*Nov 25 02:45:51.596: subset: 56 4C 41 4E 30 30 30 38 14 00 01 08 00 09 05 DC VLAN0008.......\
*Nov 25 02:45:51.596: subset: 00 01 86 A9 56 4C 41 4E 30 30 30 39 14 00 01 08 ...)VLAN0009....
*Nov 25 02:45:51.596: subset: 00 0A 05 DC 00 01 86 AA 56 4C 41 4E 30 30 31 30 ...\...*VLAN0010
*Nov 25 02:45:51.596: subset: 14 00 01 08 00 0B 05 DC 00 01 86 AB 56 4C 41 4E .......\...+VLAN
*Nov 25 02:45:51.596: subset: 30 30 31 31 14 00 01 08 00 0C 05 DC 00 01 86 AC 0011.......\...,
*Nov 25 02:45:51.596: subset: 56 4C 41 4E 30 30 31 32 18 00 02 0C 03 EA 05 DC VLAN0012.....j.\
*Nov 25 02:45:51.596: subset: 00 01 8A 8A 66 64 64 69 2D 64 65 66 61 75 6C 74 ....fddi-default
*Nov 25 02:45:51.596: subset: 30 00 03 0D 03 EB 11 78 00 01 8A 8B 74 72 63 72 0....k.x....trcr
*Nov 25 02:45:51.596: subset: 66 2D 64 65 66 61 75 6C 74 00 00 00 01 01 0C CC f-default......L
*Nov 25 02:45:51.596: subset: 04 01 03 ED 07 01 00 02 08 01 00 07 09 01 00 07 ...m............
*Nov 25 02:45:51.596: subset: 20 00 04 0F 03 EC 05 DC 00 01 8A 8C 66 64 64 69 ....l.\....fddi
*Nov 25 02:45:51.596: subset: 6E 65 74 2D 64 65 66 61 75 6C 74 00 03 01 00 01 net-default.....
*Nov 25 02:45:51.596: subset: 24 00 05 0D 03 ED 11 78 00 01 8A 8D 74 72 62 72 $....m.x....trbr
*Nov 25 02:45:51.596: subset: 66 2D 64 65 66 61 75 6C 74 00 00 00 02 01 00 0F f-default.......
*Nov 25 02:45:51.596: subset: 03 01 00 02 ....
*Nov 25 02:45:51.596:
*Nov 25 02:45:51.666: VTP LOG RUNTIME: Transmit vtp summary, domain test, rev 4, followers 1, tlv blk size 8 (inc #tlv field),
MD5 digest calculated = 8D 07 FE 82 E5 FE 49 AD 1A 6E A5 AB D0 35 C2 CA
-
Op dit moment zijn beide switches gesynchroniseerd:
Switch-A#show vtp status
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : test
VTP Pruning Mode : Disabled
VTP Traps Generation : Disabled
Device ID : 6400.f13e.dc40
Configuration last modified by 10.122.190.227 at 11-24-22 14:01:15
Feature VLAN:
--------------
VTP Operating Mode : Client
Maximum VLANs supported locally : 1005
Number of existing VLANs : 16
Configuration Revision : 4
MD5 digest : 0x8D 0x07 0xFE 0x82 0xE5 0xFE 0x49 0xAD
0x1A 0x6E 0xA5 0xAB 0xD0 0x35 0xC2 0xCA
Switch-A#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/1, Gi1/2, Gi1/4, Gi1/5
Gi1/6, Gi1/7, Gi1/8, Gi1/9
Gi1/10, Gi1/11, Gi1/12, Gi1/13
Gi1/14, Gi1/15, Gi1/16, Gi1/17
Gi1/18, Gi1/19, Gi1/20, Gi1/21
Gi1/22, Gi1/23, Gi1/24, Gi1/25
Gi1/26, Gi1/27, Gi1/28, Gi1/29
Gi1/30, Gi1/31, Gi1/32, Gi1/33
Gi1/34, Gi1/35, Gi1/36, Gi1/37
Gi1/38, Gi1/39, Gi1/40, Gi1/41
Gi1/42, Gi1/43, Gi1/44, Gi1/45
Gi1/46, Gi1/47, Gi1/48, Te3/3
Te3/4, Te3/5, Te3/6, Te3/7
Te3/8
2 VLAN0002 active
3 VLAN0003 active
4 VLAN0004 active
5 VLAN0005 active
6 VLAN0006 active
7 VLAN0007 active
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
8 VLAN0008 active
9 VLAN0009 active
10 VLAN0010 active
11 VLAN0011 active
12 VLAN0012 active
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
Voorbeeld 2:
Dit voorbeeld toont hoe u de VTP-configuratie verifieert bij een Catalyst 6000 met Cisco IOS-software:
Switch#show vtp status
VTP Version: 2
Configuration Revision: 247
Maximum VLANs supported locally: 1005
Number of existing VLANs: 33
VTP Operating Mode: Client
VTP Domain Name: Lab_Network
VTP Pruning Mode: Enabled
VTP V2 Mode: Disabled
VTP Traps Generation: Disabled
MD5 digest: 0x45 0x52 0xB6 0xFD 0x63 0xC8 0x49 0x80
Configuration last modified by 0.0.0.0 at 8-12-99 15:04:49
Switch#
Voorbeeld 3:
Dit voorbeeld toont hoe u VTP-statistieken kunt inzien op een Catalyst 6000 met Cisco IOS-software:
Switch#show vtp counters
VTP statistics:
Summary advertisements received: 7
Subset advertisements received: 5
Request advertisements received: 0
Summary advertisements transmitted: 997
Subset advertisements transmitted: 13
Request advertisements transmitted: 3
Number of config revision errors: 0
Number of config digest errors: 0
Number of V1 summary errors: 0
VTP pruning statistics:
Trunk Join Transmitted Join Received Summary advts received
from on-pruning-capable device
---------------- ---------------- ---------------- ---------------------------
Fa5/8 43071 42766 5
VTP-troubleshooting
Raadpleeg VLAN Trunk Protocol (VTP) configureren voor informatie over het oplossen van VTP-problemen.
Opmerking: Alleen geregistreerde Cisco-gebruikers hebben toegang tot de interne site, tools en documenten.
Gerelateerde informatie