この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
目次
この章の内容は、次のとおりです。
Cisco UCS Manager 2.1 は、NC-SI を使用して C シリーズ ラックマウント サーバと Cisco UCS Manager とを統合する追加オプションをサポートしています。 このオプションを使用すると、Cisco UCS Manager は、管理トラフィックとデータ トラフィックの両方でシングルワイヤを使用し、C シリーズ ラックマウント サーバを管理します。 Shared-LOM モードでは 2 つのポートを使用しますが、シングルワイヤ管理モードを使用すると、1 つの FEX のホスト側のポートでも 1 つのラックマウント サーバを十分に管理できます。 したがって、より多くのラックマウント サーバを Cisco UCS Manager 2.1 と接続し、サーバ管理を統合できます。 Cisco UCS Manager と統合するための正しいサーバ ファームウェアがあることを確認してください。 そうでない場合は、サーバを Cisco UCS Manager と統合する前にサーバ ファームウェアをアップグレードします。 C シリーズ サーバのファームウェアのアップグレードを参照してください。
(注) |
C シリーズ ラックマウント サーバ C200、C210、および C250 では、シングルワイヤ管理はサポートされていません。 |
シングルワイヤ管理には、次の注意事項と制限事項があります。
Cisco UCS ドメインで C シリーズ ラックマウント サーバの物理的な接続を確立した場合は、Cisco UCS Manager GUI または Cisco UCS Manager CLI で接続モードおよび管理ポリシーを指定する必要があります。 管理ポリシーは、接続されているすべての C シリーズ ラックマウント サーバに対してグローバルです。 接続モードは、Cisco UCS Manager でのラック サーバの検出を決定します。 ラック サーバに次のいずれかの接続ポリシーを指定できます。
ヒント |
シングルワイヤ管理でサーバを管理し、自動確認を使用する場合は、LOM ケーブルを接続しないでください。 LOM ケーブルが接続されている場合、自動確認が行われると、デュアルワイヤ管理ではサーバが検出されることがあります。 |
(注) |
Cisco UCS Manager によってラック サーバが検出され、管理されているときに、ある C シリーズ ラックマウント サーバの既存の接続モードを変更する場合は、新しい接続モードを指定する前にそのサーバの稼働を停止して再稼働する必要があります。 その後、Cisco UCS Manager は新しい接続モードのサーバだけを検出します。 |
クラスタ セットアップの要件
クラスタ セットアップで C シリーズ ラックマウント サーバと Cisco UCS Manager とのシングルワイヤ統合を作成するには、次の項目が必要です。
サーバ |
CIMC |
BIOS |
---|---|---|
Cisco UCS C22 M3 サーバ |
1.4(6) |
1.4.7a |
Cisco UCS C24 M3 サーバ |
1.4(6) |
1.4.7a |
Cisco UCS C220 M3 サーバ |
1.4(6) |
1.4.7a |
Cisco UCS C240 M3 サーバ |
1.4(6) |
1.4.7a |
Cisco UCS C260 M2 サーバ |
1.4(6) |
1.4.7 |
Cisco UCS C420 M3 サーバ |
1.4(7) |
1.4.8 |
Cisco UCS C460 M2 サーバ |
1.4(6) |
1.4.7 |
サーバには Cisco UCS VIC1225 が取り付けられている必要があります。 Cisco UCS VIC1225 のファームウェアおよびブートローダのバージョンは次のとおりです。
Cisco UCS VIC1225 は、次の表に示すように、各サーバの正しいスロットに取り付ける必要があります。
サーバ |
PCIe スロット |
---|---|
Cisco UCS C22 M3 サーバ |
1 |
Cisco UCS C24 M3 サーバ |
1 |
Cisco UCS C220 M3 サーバ |
1 |
Cisco UCS C240 M3 サーバ |
2 |
Cisco UCS C260 M2 サーバ |
7 |
Cisco UCS C420 M3 サーバ |
4 |
Cisco UCS C460 M2 サーバ |
1 |
(注) |
FEX の 2 つの電源装置それぞれに電源コードを接続する必要があります。 電源が接続されていて、ハードウェアに問題がある場合は、電源投入時自己診断テスト(POST)の途中で「重大な」障害が報告されることがあります。 たとえば、「Power supply 1 in fex 6 power: error」というエラーが表示されることがあります。 不足している電源コードを FEX 電源装置に接続すると、これらのエラーをクリアできます。 |
アップリンクで SFP タイプを混在使用しないでください。 アップリンクで SFP タイプを混在使用した場合は、「Discovery Failed」というエラーが表示されます。
非クラスタ セットアップで、Cisco UCS Manager および C シリーズ ラック マウント サーバとともにサーバを統合する場合は、次のコンポーネントが必要です。
サーバを接続する前に、Cisco UCS Manager と統合するために Cisco UCS VIC1225 が正しいスロットに取り付けられていることを確認します。 カードが正しいスロットに取り付けられていない場合は、サーバのシングルワイヤ管理をイネーブルにできません。
ステップ 1 | ラックにサーバを設置します。 使用しているサーバの『Install and Upgrade Guide』を参照してください。 インストール ガイドは、次の URL から入手できます。Install and Upgrade Guides |
ステップ 2 | FEX にデータ トラフィックと管理トラフィックの両方を伝送するパスを接続します。 |
ステップ 3 |
FEX から FI へのパスを接続します。
|
ステップ 4 | 電源コードをサーバの各電源装置に接続し、次に接地された AC 電源コンセントにコードを接続します。 |
ステップ 5 | サーバをリブートします。 |
次に、各 C シリーズ ラックマウント サーバと Cisco UCS ドメイン、Cisco UCS Manager リリース 2.1 とのシングルワイヤでの物理的な接続の図を示します。
次の図は、C22 M3 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
4 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
5 |
Cisco UCS C22 M3 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
6 |
PCIe スロット 1 の Cisco UCS VIC1225 |
次の図は、C24 M3 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
4 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
5 |
Cisco UCS C24 M3 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
6 |
PCIe スロット 1 の Cisco UCS VIC1225 |
次の図は、C220 M3 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
5 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
6 |
Cisco UCS C220 M3 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
7 |
PCIe スロット 1 の Cisco UCS VIC1225 |
次の図は、C240 M3 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
4 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
5 |
Cisco UCS C240 M3 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
6 |
PCIe スロット 2 の Cisco UCS VIC1225 |
次の図は、C420 M3 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
4 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
5 |
Cisco UCS C420 M3 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
6 |
PCIe スロット 4 の Cisco UCS VIC1225 |
次の図は、C260 M2 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
4 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
5 |
Cisco UCS C260 M2 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
6 |
PCIe スロット 7 の Cisco UCS VIC1225 |
次の図は、C460 M2 サーバと Cisco UCS Manager を統合する場合の配線を表しています。 金色で示されるパスは、管理トラフィックとデータ トラフィックの両方を伝送します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
4 |
Cisco Nexus 2232PP FEX(ファブリック B) |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
5 |
Cisco UCS C460 M2 サーバ |
3 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック B) |
6 |
PCIe スロット 1 の Cisco UCS VIC1225 |
「クラスタ セットアップでの C シリーズ サーバと Cisco UCS ドメインとの接続」での説明と同じ手順に従ってください。 2 つの FI と 2 つの FEX を接続するのではなく、1 つの FI と 1 つの FEX だけを接続します。
次の図は、シングルワイヤ管理での非クラスタ セットアップの例を示します。
1 |
Cisco UCS 6100 シリーズまたは 6200 FI(ファブリック A) |
3 |
Cisco UCS C シリーズ サーバ |
2 |
Cisco Nexus 2232PP FEX(ファブリック A) |
4 |
PCIe スロット 1 の Cisco UCS VIC1225 |
Cisco UCS Manager を使用して Cisco UCS ドメインに統合されているすべてのラックマウント サーバを管理およびモニタすることができます。 統合後は、ラックマウント サーバの管理タスクはすべて Cisco UCS Manager GUI または Cisco UCS Manager CLI のサービス プロファイルからのみ実行します。 Cisco UCS Manager によるサーバの管理を開始すると、C シリーズ ラックマウント サーバの CIMC は使用できなくなります。
Cisco UCS Manager は、検出した各ラックマウント サーバの情報、エラー、および障害を提供します。
Cisco UCS Manager からの C シリーズ ラックマウント サーバの管理の詳細については、各リリースの『Cisco UCS Manager GUI Configuration Guide』の「Managing Rack-Mount Servers」の章を参照してください。
Cisco UCS Manager ソフトウェアを使用して Cisco UCS C シリーズ サーバを管理すると、そのサーバに UCS Manager サービス プロファイルが関連付けられます。 C シリーズ サーバをスタンドアロン モードに戻す(すなわち CIMC ソフトウェアで管理できるようにする)場合は、UCS Manager で次の処理を行う必要があります。