この製品のマニュアルセットは、偏向のない言語を使用するように配慮されています。このマニュアルセットでの偏向のない言語とは、年齢、障害、性別、人種的アイデンティティ、民族的アイデンティティ、性的指向、社会経済的地位、およびインターセクショナリティに基づく差別を意味しない言語として定義されています。製品ソフトウェアのユーザーインターフェイスにハードコードされている言語、RFP のドキュメントに基づいて使用されている言語、または参照されているサードパーティ製品で使用されている言語によりドキュメントに例外が存在する場合があります。シスコのインクルーシブランゲージに対する取り組みの詳細は、こちらをご覧ください。
このドキュメントは、米国シスコ発行ドキュメントの参考和訳です。リンク情報につきましては、日本語版掲載時点で、英語版にアップデートがあり、リンク先のページが移動/変更されている場合がありますことをご了承ください。あくまでも参考和訳となりますので、正式な内容については米国サイトのドキュメントを参照ください。
目次
この章の内容は、次のとおりです。
Cisco Adapter FEX with FCoE 機能を使用すると、Cisco Nexus 2000 シリーズ ファブリック エクステンダ(FEX)への FCoE 接続を作成し、仮想インターフェイス カード(VIC)アダプタによってサーバへの FCoE 接続を確立できます。
たとえば、この機能を使用して Cisco UCS P81E 仮想インターフェイス カード を含む Cisco UCS C シリーズ ラックマウント サーバ に Nexus スイッチを接続したり、Broadcom BCM57712 コンバージェンスのネットワーク インターフェイス カード(C-NIC)がインストールされているサードパーティ製サーバに接続したりすることができます。
スイッチは仮想ポート チャネル(vPC)経由で FEX に接続し、FEX は FEX と VIC アダプタ間の標準 FCoE リンクを使用してサーバに接続します。
拡張 vPC を使用する場合は、FEX を、FCoE 転送の 1 つの Nexus 5000 ファブリックだけに関連付けることができます。
FabricPath を使用する場合は、FCoE トラフィックの専用リンクを使用する必要があります。
Cisco UCS P81E 仮想インターフェイス カード(VIC)付きの Cisco UCS C シリーズ ラックマウント サーバ を使用する場合は、次のとおりです。
1. configure terminal
2. install feature-set virtualization
3. feature-set virtualization
4. fex fex-chassis-ID
5. fcoe
6.
interface ethernet [fex-chassis-ID/]slot/port
7. switchport mode vntag
8. interface vethernet veth-id
9. bind interface ethernet [fex-chassis-ID/]slot/port channel channel-no
10. switchport mode {trunk|access}
11. (任意) switchport trunk allowed vlan vlan-ID
12. (任意) switchport access vlan vlan-ID
13. interface vfc vfc-id
14. bind interface vethernet veth-num
15. no shutdown
次に、トランク ポートとして設定されたチャネル 1 の FEX 101 およびイーサネット インターフェイスを使用して、SAN ファブリック A の Cisco Adapter FEX with FCoE を設定する例を示します。
nexus5000-sanA(config)#configure terminal nexus5000-sanA(config)#install feature-set virtualization nexus5000-sanA(config)#feature-set virtualization nexus5000-sanA(config)#fex 101 nexus5000-sanA(config-fex)#fcoe nexus5000-sanA(config-fex)#interface ethernet 101/1/1 nexus5000-sanA(config-if)#switchport mode vntag nexus5000-sanA(config-if)#interface veth 2 nexus5000-sanA(config-if)#bind interface eth 101/1/1 channel 1 nexus5000-sanA(config-if)#switchport mode trunk nexus5000-sanA(config-if)#switchport trunk allowed vlan 33 nexus5000-sanA(config-if)#interface vfc 4 nexus5000-sanA(config-if)#bind interface veth 2 nexus5000-sanA(config-if)#no shutdown
次に、アクセス ポートとして設定されたチャネル 2 の FEX 102 およびイーサネット インターフェイスを使用して、SAN ファブリック B の Cisco Adapter FEX with FCoE を設定する例を示します。
nexus5000-sanB(config)#configure terminal nexus5000-sanB(config)#install feature-set virtualization nexus5000-sanB(config)#feature-set virtualization nexus5000-sanB(config)#fex 102 nexus5000-sanB(config-fex)#fcoe nexus5000-sanB(config-fex)#interface ethernet 102/1/1 nexus5000-sanB(config-if)#switchport mode vntag nexus5000-sanB(config-if)#interface veth 5 nexus5000-sanB(config-if)#bind interface eth 102/1/1 channel 2 nexus5000-sanB(config-if)#switchport mode access nexus5000-sanB(config-if)#switchport access vlan 40 nexus5000-sanB(config-if)#interface vfc 6 nexus5000-sanB(config-if)#bind interface veth 5 nexus5000-sanB(config-if)#no shutdown