Show Command(s) and/or Outputs
show subscribers control-plane-only all
This command displays the following Control Plane specific information for the session. Following is a sample output:
-
Access Type
-
(R) - sgw-pdn-type-ipv4
-
(O) - sgw-pdn-type-ipv6
-
(Q) - sgw-pdn-type-ipv4-ipv6
-
(@) - saegw-gtp-ipv4
-
(#) - saegw-gtp-ipv6
-
($) - saegw-gtp-ipv4-ipv6
-
(W) - pgw-gtp-ipv4
-
(Y) - pgw-gtp-ipv6
-
(Z) - pgw-gtp-ipv4-ipv6
-
(.) – Unknown
-
-
Access Tech
-
(U) - UTRAN
-
(G) - GERAN
-
(E) - eUTRAN
-
(.) - Unknown
-
-
Call State
-
(C) - Connected
-
(c) - Connecting
-
(S) - Suspended
-
(d) - Disconnecting
-
(I) - Idle
-
(u) - Unknown
-
-
Bearer Type
-
(D) - Default
-
(E) - Dedicated
-
(I) - Indirect Forwarding
-
-
PLMN
-
(H) - Home
-
(V) – Visiting
-
(R) - Roaming
-
(u) - Unknown
-
-
Emergency Bearer Type
-
(A) - Authentic IMSI
-
(U) - Un-Authentic IMSI
-
(O) - Only IMEI
-
(N) - Non-Emergency
-
-
Addr
-
(L) - Local pool
-
(S) - Static (Subscriber Supplied)
-
Type: (u) - Unknown
-
-
CALLID
-
LOCAL SEID
-
IMSI/IMEI
-
EBI
-
V
-
IP
-
PDN-INSTANCE
-
User Plane Address
-
TIME-IDLE
Note |
|
show session disconnect-reasons
The following disconnect reasons has been added in support of Control Plane in CUPS:
-
user-plane-info-not-available(651)
This disconnect reason is seen in following conditions:
-
user-plane-profile is not associated with APN Profile for Pure-S call.
-
user-plane-profile is not associated with IP Pool for Pure-P call.
-
Associated user-plane-profile is not configured.
-
Associated user-plane-profile is not configured with endpoint address
-
-
user-plane-info-mismatch(652)
-
For multiple PDN call with same APN, and for IPv4 and IPv6 call, it is mandatory that same User Plane profile is selected. Any variation will result in call creation failure with this disconnect reason.
-
-
sx-max-trans-threshold-reached(676): Calls are dropped with this disconnect reason if the outstanding Sx transaction exceeds 12.
show subscribers saegw-only full all
Executing this command displays the following fields:
-
User Plane Address
-
Local SEID
-
Remote SEID
-
show subscribers saegw-only seid seid_value
Executing this command displays the following fields:
-
vvvvvv
-
CALL ID
-
IMSI/IMEI
-
EBI
-
v
-
IP
-
APN
-
TIME-IDLE
show user-plane-service statistics charging action
This command displays charging action statistics for all or specified charging actions that are configured in the Active Charging Service (ACS). A charging action represents actions to be taken when a configured rule is matched. Actions range from generating accounting records to dropping the IP packet, and so on. The charging action also determines the metering principle—Whether to count retransmitted packets, and which protocol field to use for billing (L3/L4/L7, and so on).
Syntax
show user-plane-service statistics charging-action
{ all [ debug-info | verbose] | name charging_action_name [ debug-info | verbose] } [ | { grep grep_options | more } ]
Notes:
-
all : Displays information for all charging actions configured in ACS.
-
name charging_action_name : Displays information for an existing charging action specified as an alphanumeric string from 1 through 63 characters.
This show CLI command doesn't support the following statistics with the value 0 that is displayed for each of its counter value.
PP Flows Readdressed:0
Bytes Charged Yet Packet Dropped:0
Predef-Rules Deactivated:0
Outer IP header dscp marked Pkts:0
Tethering Blocking Statistics:
TTL Modified downlink packets:0
Throttle-Suppress Stats:
Uplink Bytes:0 Downlink Bytes:0
XHeader Information:
IP Frags consumed by XHeader:0 IP Frags consumed by XHeader:0
Strip URL:
Successful Token stripped:0
Total strip URL failure:0
Failure - Missing config:0
Failure - Existing flow bid:0
Failure - Token matching failed:0
Failure - Empty packet:0
Failure - Req end not found:0
Failure - Subset of big token:0
URL-Readdressing:
Requests URL-Readdressed:0
Total Charging action hit - Req. Readdr.:0
Proxy Disable Success:0
Flows connected to URL Server:0
URL-Readdressing Error Conditions:
Total connect failed to URL Server:0
URL Readdress- pipelined case:0
URL Readdress- Socket Mig. Failed:0
Proxy Disable Failed:0
CAE-Readdressing:
Requests CAE-Readdressed:0
Responses CAE-Readdressed:0
Requests having MVG xheader inserted:0
Total CAE-Readdressed Uplink Bytes:0
Total CAE-Readdressed Uplink Packets:0
Total CAE-Readdressed Downlink Bytes:0
Total CAE-Readdressed Downlink Packets:0
Total Charging action hit - Req. Readdr.:0
Total Charging action hit - Resp. Readdr:0
Proxy Disable Success:0
Flows connected to CAE:0
CAE Readdressing Error Conditions:
Total connect failed to CAE:0
Req. Readdr. - pipelined case:0
Skipped Resp. Readdr. - pipelined req:0
Req. Readdr. - Socket Mig. failed:0
Skipped Resp. Readdr. - partial resp hdr:0
Resp. Readdr. - Socket Mig. failed:0
Total CAE load balancer failed:0
Total MVG xheader insertion failed:0
Proxy Disable Failed:0
Rulebase Changed by flow action:0
Terminate Session:0
P2P random dropped packets:0
show user-plane-service statistics group-of-ruledefs
This command displays statistics for all groups or a specified group of ruledef s configured in the active charging service. The group-of-ruledefs is a collection of rule definitions that can be used in access policy creation.
Syntax
show user-plane-service statistics group-of-ruledefs { all | name group_of_ruledefs_name } [ | { grep grep_options | more } ]
Notes:
-
all : Displays information for all groups of ruledefs configured in ACS.
-
name group_of_ruledefs_name : Displays detailed information for an existing group of ruledefs specified as an alphanumeric string from 1 through 63 characters.
-
{ grep grep_options | more } Pipes : Sends the output of this command to the specified command.
-
The following clear CLI command is available for use: clear user-plane-service statistics group-of-ruledefs { all | name group_of_ruledefs_name }
show user-plane-service statistics ruledef
This command displays statistics for all or specified ruledef that is configured in an active charging service. The ruledef represents a set of matching conditions across multiple L3 - L7 protocol that is based on protocol fields and state information. You can use each ruledef across multiple rule bases within the active charging service.
Syntax
show user-plane-service statistics ruledef { all { charging | firewall [ wide ] | post-processing } | name ruledef_name [ wide ] } [ | { grep grep_options | more } ]
Notes:
-
all : Displays statistics for all ruledef s of the specified type that is configured in the ACS.
-
charging : Displays statistics for all charging ruledef s configured in the ACS.
-
firewall : Displays statistics for all firewall ruledef s configured in the service.
-
post processing : Displays statistics for all post processing ruledef s configured in the ACS.
-
name ruledef_name : Displays statistics for an existing ruledef specified as an alphanumeric string from 1 through 63 characters.
-
wide : Displays all available information in a single wide line.
-
The following clear CLI command is available for use: clear user-plane-service statistics ruledef { all | charging | firewall | name group_of_ruledefs_name }