show ggsn-service

This chapter includes the show ggsn-service command output tables.

show ggsn-service sgsn-table

Table 1. show ggsn-service sgsn-table Command Output Descriptions
Field Description

GTP Version

GPRS Tunnelling Protocol. (0) - GTPRS (1) - UMTS

Active

GTP condition. (I) - Inactive (A) - Active

GTPC Echo

GPRS Tunneling Protocol-Control message (D) - Disabled (E) - Enabled

PLMN Type

Public land mobile network type. (H) - Home (F) - Foreign (U) - Unknown

SGSN Stats

SGSN statistics. (A) - Available (U) - Unavailable

Service ID

GGSN Service ID.

SGSN Address

IP address of each active SGSN.

Restart Counter

The restart counter sent by the SGSN. Increments by 1 with each restart.

Number of Restarts

Number of times the restart of the particular SGSN is detected, i.e., the number of times a NEW restart counter is received from the SGSN in a GTPC request message.

Curr Subs

Number of current subscribers to each SGSN.

Max Subs

Maximum number of permitted subscribers to each SGSN.

show ggsn-service all

Displays the configuration information for all GGSN services configured on the system.

Table 2. show ggsn-service all Command Output Descriptions
Field Description

Service name

The name of the GGSN service.

Context

The context name where the GGSN service is configured.

Associated PGW svc

The name of the P-GW service associated to the GGSN service.

Associated GTPU svc

The name of the GTP-U service associated to the GGSN service.

Associated IPNE svc

The name of the IPNE service associated to the GGSN service.

Associated Peer map

The name of the peer map associated to the GGSN service.

Accounting Context Name

The context name where the accounting configuration and/or interface(s) are configured.

dns-client Context Name

The context name in which a DNS client configuration is present.

Authorize

Enables/disables subscriber session authorization with HSS over S6b Diameter interface.

S6b IPv6 Reporting

Specifies if the IPv6 address reporting through AAR towards the S6b interface is enabled or disabled.

Fqdn-name

The name of Fully Qualified Domain Name (FQDN) which is used for authorization over S6b interface between GGSN and 3GPP AAA/HSS.

Bind

Binds the GGSN service to a logical IP interface serving as the Gn interface.

Local IP Address

The IP address (IPv4 and/or IPv6)) of the interface configured as the Gn interface.

Self PLMN Id

Specifies the GGSN's public land mobile network (PLMN) identifiers.

Retransmission Timeout

The time to control the retransmission of GTP control packets when no response is received from an SGSN.

Max Retransmissions

Indicates the maximum number of times that GTP control packets are retransmitted.

Restart Counter

Specifies the restart counter

Echo Interval

Specifies the frequency at which the GGSN service sends GTPv1-C Echo packets to the SGSN(s) it is configured to communicate with.

GTPC Echo Mode

Specifies if GTP-C echo mode is set as default.

GTPC Echo Retransmission Timeout

Specifies the frequency at which the GGSN service retransmits GTPv1-C Echo packets to the SGSN(s) it is configured to communicate with.

Guard Interval

Specifies the amount of time that must pass before a GGSN service treats a redundant PDP context request as a new request instead of a re-send of a previous request.

PLMN Policy

Specifies the public land mobile network (PLMN) policy.

Setup Timeout

Specifies the maximum amount of time the GGSN service allows for the setting up of PDP contexts.

S-GW Interface Excluded

Excludes the specified interface.

SGSN MCC MNC preference

Specifies the MCC and MNC preference for SGSN.

Unlisted SGSN PLMN Id.

Specifies the PLMN ID of the unlisted SGSN.

Unlisted SGSN rat-type

Specifies the type of the radio acess technology for unlisted SGSN.

Reject Code Policy

Authentication Server Timeout

Specifies the reject code used by the GGSN if communication with an authentication server times out.

Accounting Server Timeout

Specifies the reject code used by the GGSN if communication with an accounting server times out.

Ran Procedure Ready

Specifies if the RAN Procedure Ready feature is enabled/disabled for the specified GGSN service.

NSAPI in Create PDP response

Specifies the Network Service Access Point Identifier in the Create PDP response.

Map MBR to AMBR in Update PDP request

Indicates the status of MBR to AMBR mapping in Update PDP Context Request message.

Suppress NRUPC triggered by CPC

Indicates if suppress NRUPC triggered by CPC is enabled or disabled.

Suppress NRUPC triggered by UPC

Indicates if suppress NRUPC triggered by UPC is enabled or disabled.

Support e-ARP

Indicates if the support for enhanced ARP is enabled or disabled.

Support MS QoS Change

Indicates if the support for MS QoS change is enabled or disabled.

Decode MCC MNC parameter of ULI as HexaDecimal Digits

Indicates if the decoding of MCC and MNC parameters of ULI as hexadecimal digits has been enabled or disabled.

Duplicate Subscriber Address Request

Specifies the status of duplicate subscriber address request.

trace-collection-entity

Specifies the trace collection entity which is the destination node in Network management where trace files are transferred to and stored.

Path Failure Detection on gtp msgs

Specifies the path failure detection policy on GTP-U echo messages that have been retransmitted the maximum number of retry times.

GTP Private Extensions

Specifies the customer specific private extension in GTP-C messages.

Max IP sessions

Specifies the maximum numner of IP sessions.

Max PPP sessions

Specifies the maximum number of PPP sessions in GGSN service.

Max sessions

Specifies the total number of maximum sessions including IP and PPP in GGSN service.

Max Primary sessions

Specifies the total number of maximum primary sessions including IP and PPP in GGSN service.

Max Sec-per-primary sessions

Specifies the total number of maximum secondary sessions per primary session in GGSN service.

Service Status

Specifies the status of the GGSN service.

Newcall Policy

Specifies if the new call related behavior of GGSN service is enabled/disabled when duplicate sessions with same IP address request is received.

MBMS Policy

Specifies the configured MBMS policy for Multicast and/or Broadcast mode in this GGSN service.

MBMS Charging ID Optimization

Specifies if the MBMS charging ID optimization is enabled/disabled for the GGSN service.

GTPC Prioritized APN(s

Specifies if the prioritized APNs have been added for prioritized handling of VoLTE/Emergency calls even under congestion for the GGSN service.

GTPC Prioritized ARP(s)

Specifies if the prioritized ARPs have been added for prioritized handling of VoLTE/Emergency calls even under congestion for the GGSN service.

GTPC Prioritized Rel99 ARP(s)

Specifies if the prioritized Release 99 ARPs have been configured for prioritized handling of VoLTE/Emergency calls even under congestion for the GGSN service.

3GPP Qos to DSCP Mapping (for G-PDUs)

This group indicates the 3GPP QoS to DSCP mapping information.

qci 1: ef

Indicates the DSCP configured for QCI1 type of traffic.

qci 2: ef

Indicates the DSCP configured for QCI2 type of traffic.

qci 3: af11

Indicates the DSCP configured for QCI3 type of traffic.

qci 4: af11

Indicates the DSCP configured for QCI4 type of traffic.

qci 5: ef

Indicates the DSCP configured for QCI5 type of traffic.

qci 6: ef

Indicates the DSCP configured for QCI6 type of traffic.

qci 7: af21

Indicates the DSCP configured for QCI7 type of traffic.

qci 8: af21

Indicates the DSCP configured for QCI8 type of traffic.

qci 9: be

Indicates the DSCP configured for QCI9 type of traffic.

3GPP Qos to DSCP Mapping based on Alloc. Prio

This group indicates the 3GPP QoS to DSCP mapping information based on allocation priority.

qci 5 ( Alloc.P 1): ef

Indicates the DSCP configured for QCI5 type of traffic with allocation priority 1.

qci 5 ( Alloc.P 2): ef

Indicates the DSCP configured for QCI5 type of traffic with allocation priority 2.

qci 5 ( Alloc.P 3): ef

Indicates the DSCP configured for QCI5 type of traffic with allocation priority 3.

qci 6 ( Alloc.P 1): ef

Indicates the DSCP configured for QCI6 type of traffic with allocation priority 1.

qci 6 ( Alloc.P 2): ef

Indicates the DSCP configured for QCI6 type of traffic with allocation priority 2.

qci 6 ( Alloc.P 3): ef

Indicates the DSCP configured for QCI6 type of traffic with and allocation priority 3.

qci 7 ( Alloc.P 1): af21

Indicates the DSCP configured for QCI7 type of traffic with allocation priority 1.

qci 7 ( Alloc.P 2): af21

Indicates the DSCP configured for QCI7 type of traffic with allocation priority 2.

qci 7 ( Alloc.P 3): af21

Indicates the DSCP configured for QCI7 type of traffic with allocation priority 3.

qci 8 ( Alloc.P 1): af21

Indicates the DSCP configured for QCI8 type of traffic with allocation priority 1.

qci 8 ( Alloc.P 2): af21

Indicates the DSCP configured for QCI8 type of traffic with allocation priority 2.

qci 8 ( Alloc.P 3): af21

Indicates the DSCP configured for QCI8 type of traffic with allocation priority 3.

GTPC messages

Indicates the Best effort forwarding PHB for GTPC messages.

CC Behavior

Specifies the 3GPP behavior bit associated with the GGSN's charging characteristics.

Charging Characteristics (CC) Profiles

This group provides the charging characteristics profiles configured in this GGSN service.

Bucket

Specifies the charging bucket configured for charging characteristic in this GGSN service

SGSN Configuration List

Specifies the list of SGSNs that this GGSN service is allowed to communicate with.

GTPC Outgoing Throttling

Specifies if outgoing throttling has been enabled, which indicates the number of messages that were removed from the queue (due to any collision, or max retransmission expired).

RLF Template Name

Specifies the template name for RLF for throttling support.

GTPC Incoming Throttling Params

Specifies if the incoming throttling of GTPC has been configured. It includes following parameters:

Message Rate (per sec)

Indicates the number of messages per second. Default: 20000

Delay Tolerance (secs)

Indicates the delay tolerance in seconds. Default: 5

Queue Size

Indicates the queue size. Default: 10000