show lte-policy

This chapter describes the output of the show lte-policy command.

show lte-policy congestion-action-profile name


Important

In Release 20, 21.0 and 21.1, HeNBGW is not supported. For more information, contact your Cisco account representative.
Table 1. show lte-policy congestion-action-profile name Command Output Descriptions
Field Description

handovers

Indicates the action the MME is configured to take for handovers when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

combined-attaches

Indicates the action the MME is configured to take for combined Attach requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

ps-attaches

Indicates the action the MME is configured to take for packet switched Attach requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

addn-pdn-connects

Indicates the action the MME is configured to take for additional PDN context connections when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

addn-brr-requests

Indicates the action the MME is configured to take for additional bearer requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

brr-ctxt-mod-requests

Indicates the action the MME is configured to take for Bearer Resource Context Modification Requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

service-request

Indicates the action the MME is configured to take for service requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

tau-request

Indicates the action the MME is configured to take for TAU requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

s1-setups

Indicates the action the MME is configured to take for S1 setup attempts when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

init-ues

Indicates the action the HeNBGW is configured to take for Initial UE messages received when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

paging

Indicates the action the HeNBGW is configured to take for Paging requests when a congestion control threshold is reached. Possible actions are none (ignore), reject, drop.

exclude-emergency-events

Indicates whether the MME is configured to exclude emergency calls when a congestion control threshold is reached. This setting is disabled when 'no exclude-emergency-events' is displayed.

exclude-voice-events

Indicates whether the MME is configured to exclude voice calls when a congestion control threshold is reached. This setting is disabled when 'no exclude-voice-events' is displayed.

report-overload

Indicates whether the MME is configured to report overload conditions to eNodeBs to alleviate congestion scenarios.

show lte-policy cause-code-group name

Table 2. show lte-policy cause-code-group name Command Output Descriptions
Field Description

Cause Code Group name

S1AP Protocol

class

Lists the configuration of each cause code entry, organized by class (miscellaneous, nas, protocol, radio, trasnport), for this Cause Code Group.

show lte-policy foreign-plmn-guti-mgmt-db name

Table 3. show lte-policy foreign-plmn-guti-mgmt-db name Command Output Descriptions
Field Description

Foreign PLMN GUTI Management DB name

PLMN

Lists the management database PLMN entries and the configuration of each entry.

show lte-policy ho-restrict-list name

Table 4. show lte-policy ho-restrict-list name Command Output Descriptions
Field Description

forbidden tracking areas

Lists the PLMN IDs which are part of the handover restriction list.

forbidden location areas

Lists the PLMN IDs which are part of the handover restriction list.

show lte-policy lte-emergency-profile name

Table 5. show lte-policy lte-emergency-profile name Command Output Descriptions
Field Description

ue-validation-level

Indicates the type of UE that can use the emergency bearer service through this profile.

apn

Indicates the name and PDN type of the access point name (APN) used for emergency PDN connections.

If enabled, the configured restoration priority of 1 through 16 is displayed (1 is highest priority, 16 is lowest).

qos

Indicates the quality of service (QoS) settings for this emergency bearer service.

ambr

Indicates the maximum aggregated uplink and downlink bitrate values for this profile.

FQDN PGW

Indicates the Fully Qualified Domain Name of the P-GW to be used for emergency bearer services through this profile.

STATIC PGW

Indicates the static IP address, protocol, and weight of the P-GW to be used for emergency bearer services through this profile.

LCS QOS

Indicates the configuration of the lcs-qos command for this LTE emergency profile. This displays the location service QoS settings to be used for this emergency profile.

Horizontal Accuracy: The horizontal positioning accuracy value.

Vertical Accuracy: The vertical positioning accuracy value.

UE Usage Type

Configures UE usage type for disconnecting PDN for up service area

Co-located Node

Configures the collocated node name to select the collocated SPGW node IP addresses.

show lte-policy tai-mgmt-db name

Table 6. show lte-policy tai-mgmt-db name Command Output Descriptions
Field Description

attach-only

Specifies the SGW preference for SGW-relocation.

show lte-policy paging-map name

Table 7. show lte-policy paging-map name Command Output Descriptions
Field Description

Paging Map n

Precedence

Indicates the order in which the MME checks the entries for this paging-map.

Traffic Type

Indicates the traffic type such as CS, PS, SIGNALING and sub-type that is specified for this paging-map.

Paging profile

Indicates the paging-profile to be used for this traffic type.

Precedence

Displays the configured precedence value.

Packet-Switched(PS)

Displays the paging is for Packet-Switched traffic.

APN

Displays the configured APN profile name.

ARP

Displays the configured ARP value.

Paging is performed as per paging-profile <name>

Displays the paging profile name.

show lte-policy paging-profile name

Table 8. show lte-policy paging-profile name Command Output Descriptions
Field Description

Paging Profile n

Paging Stage n: Lists all Paging Stages configured for this Paging Profile.

Paging Action

Indicates how the paging request should be formed. Possible options are:
  • all-enb-all-tai
  • all-enb-last-tai
  • last-n-enb-last-tai

Match Criteria

Indicates the criteria for selecting a given paging stage. Possible options are:
  • ue-contact-time
  • all

T3413-Timeout

Indicates the time interval in seconds between paging requests.

Max Paging Retries

Indicates the number of paging requests to be sent out during this paging stage.

show lte-policy tai-mgmt-db name

Table 9. show lte-policy tai-mgmt-db name Command Output Descriptions
Field Description

TAI Management DB n

Time Zone

Indicates the time zone settings to be used for the UE timezone in S11 and NAS messages.

Short Network Name

Indicates the short network name to be used in the Short network name IE in the EMM Information message sent by the MME.

Long Network Name

Indicates the full (long) network name to be used in the Long network name IE in the EMM Information message sent by the MME.

TAI Management Object

The name of the TAI managment object and all configured options for the object. For each TAI Management Object, the following information is displayed, if configured:
  • Time Zone
  • Zone Code
  • IMS Voice over PS support
  • LAI (Location Area Identifer)
  • TAI (Tracking Area Identifier)
  • RAI (Routing Area Identifier)
  • SGW IP address, protocol, and weight priority infomation
  • Full and/or Short Network Name

Access-Type NB-IoT

Displays the configured access type. The show output displays whether all the TACs configured belong to either WB-EUTRAN or NB-IoT RAT. It is also possible that some of the configured TACs belong to WB-EUTRAN and the rest belong to NB-IoT RAT.

UE Usage Type

Configures UE usage type for disconnecting PDN for up service area

Co-located Node

Configures the collocated node name to select the collocated SPGW node IP addresses.