Cisco Unified SIP Proxy Module EXEC Commands
Last Updated: April 8, 2019
cusp
To enter Cisco Unified SIP Proxy EXEC mode, use the cusp command in module EXEC mode. To exit Cisco Unified SIP Proxy EXEC mode, use the exit command.
cusp
Syntax Description
This command has no arguments or keywords.
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
1.0 |
This command was introduced. |
Examples
The following example accesses the Cisco Unified SIP Proxy module and enters Cisco Unified SIP Proxy EXEC mode:
Router# service-module integrated-service-engine 1/0 session
Related Commands
|
|
configure |
Enters Cisco Unified SIP Proxy configuration mode. |
exit |
Exits out of a Cisco Unified SIP Proxy configuration or management mode and returns to the higher mode. |
shutdown graceful
To perform a graceful shutdown of the Cisco Unified SIP Proxy module, use the shutdown graceful command in module EXEC mode.
shutdown graceful [ timeout ]
Syntax Description
timeout |
(Optional) Specifies the timeout value for the Cisco Unified SIP Proxy module. The valid range is 10 to 180 seconds. The default is 32 seconds. |
Command Default
The default timeout value is 32 seconds.
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
1.0 |
This command was introduced. |
Usage Guidelines
The timeout value specifies how long the Cisco Unified SIP Proxy waits for pending tasks to complete before exiting.
Examples
The following example executes a graceful shutdown of the Cisco Unified SIP Proxy module, specifying a timeout value of 120 seconds:
se-10-0-0-0# shutdown graceful 120
Related Commands
|
|
reload |
Restarts the Cisco Unified SIP Proxy system after the shutdown command has been used and activates the uploaded file information after the restore command has been used. |
ip route
To establish static routes to Cisco Unified SIP Proxy’s virtual interfaces and other routers, use the ip route command in module configuration mode.
ip route destination-ip destination-mask { gigabitethernet | ip-address }
Syntax Description
destination-ip |
Destination network address. |
destination-mask |
Destination network address mask. |
gigabitethernet |
Virtual interface to which to route. |
ip-address |
Forwarding router’s address. |
Command Default
No static routes are established.
Command Modes
Module configuration (config)
Command History
Cisco Unified SIP Proxy Version
|
|
1.0 |
This command was introduced. |
Usage Guidelines
The last argument specifies the forwarding address which is either the virtual interface to route to or the forwarding router’s address.
Examples
The following example establishes a static route to Cisco Unified SIP Proxy’s Gigabit Ethernet interface 0.2:
se-10-0-0-0(config)# ip route 10.10.10.2 255.255.255.0 GigabitEthernet0.2
The following example establishes a static route to the router whose IP address is 10.10.20.2:
se-10-0-0-0(config)# ip route 10.10.10.2 255.255.255.0 10.10.20.2
show license smart udi
To display the Unique Device Identifier (UDI) of Cisco Unified SIP Proxy, use the show license smart udi command in module EXEC mode.
show license smart udi
Syntax Description
This command has no arguments or keywords.
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Examples
The following example shows the Cisco Unified SIP Proxy software UDI:
se-9-41-12-29# show license smart udi
Serial Number: VJQ6q77nQod
show license smart summary
To show current state of the Cisco Unified SIP Proxy licensing application, entitlement count, time left in evaluation mode (if applicable), product specific details, authorization and registration related timers, and to capture recent failures with communication related to licensing server, use the show license smart summary command in module EXEC mode.
show license smart summary
Syntax Description
This command has no arguments or keywords.
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Examples
The following example shows current state of the Cisco Unified SIP proxy licensing application:
se-10-104-45-238# show license smart summary
Smart Agent is Enabled: true
Current State of the Agent: UNIDENTIFIED
Requested license count: 25
Entitlement tag: CUSP-5-TAG-1
Configured destination address:https://tools.cisco.com/its/service/oddce/services/DDCEService
Transport Mode: TransportCallHome
Evaluation period : 1890
show license smart status application cusp
To capture the current state of the licensing agent, use the show license smart status application cusp command in module EXEC mode.
show license smart status application cusp
Syntax Description
This command has no arguments or keywords.
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Examples
The following example shows current state of the licensing agent:
se-10-104-45-238# show license smart status application cusp
Smart Agent is Enabled: true
Smart Agent current state: UNIDENTIFIED
license smart destinationAddr
To specify the smart manager URL, use the license smart destinationAddr command in module EXEC mode.
license smart destinationAddr url
Syntax Description
url |
Connects to the central licensing server. |
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Usage Guidelines
Use this command to configure the central license URL.
Examples
The following example configures the smart manager URL:
se-10-0-0-0# license smart destinationAddr
https://tools.cisco.com/its/service/oddce/services/D
license smart httpProxyAddr
To set the HTTP(S) proxy server address for smart licensing, use the license smart httpProxyAddr command in module EXEC mode.
license smart httpProxyAddr url
Syntax Description
url |
Specifies the HTTP proxy address. |
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Usage Guidelines
If HTTP Proxy is required to connect to the smart manager, use this command to set the proxy address through which the request will be sent.
Examples
The following example specifies the HTTP(S) proxy server address for smart licensing:
se-10-0-0-0# license smart httpProxyAddr 10.1.1.1
license smart activate cusp
To enable smart agent licensing in Cisco Unified SIP Proxy, use the license smart activate cusp command in module EXEC mode. To enable call routing through Cisco Unified SIP Proxy, this command must be enabled. Else, the calls will drop.
license smart activate cusp count
Syntax Description
count |
Specifies the maximum calls per second. The value should be a multiple of 5. |
Command Modes
Module EXEC (>)
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Usage Guidelines
Set license smart destinationAddr before running this command. If HTTP proxy is required, execute license smart httpProxyAddr before you execute this command.
Examples
The following example sets the maximum calls per second:
se-10-0-0-0# license smart activate cusp 100
license smart register token_id
To register the device instance with the Cisco licensing cloud, use license smart register token_id in module EXEC mode. Execute license smart activate cusp before you execute this command.
license smart register token_id token
Syntax Description
token |
Specifies the token generated in smart manager. |
Command Modes
Cisco Unified SIP Proxy configuration (cusp-config)
Command History
Cisco Unified SIP Proxy Version
|
|
9.0 |
This command was introduced. |
Usage Guidelines
Use this command to register the device instance with the Cisco licensing cloud.
Examples
The following example registers and sets the token ID required for registration of smart agent on Cisco Unified SIP Proxy:
se-10-0-0-0# license smart register token_id
MjgxZjdkY2RtMWY5Ny00YTk4LOI2N2MtNjcxNmYaMTkzZGFhLHE0
MjA3MjY0%0AMjI5N34Z8OVAOdmNzSjdIeG4MMHIzTmZubNFzMHhK
OTYyeHlUZWQzQzVIM3Jk%0AHVk3MD0A3D%0N