|
|
|
|
Module EXEC |
When the integrated services engine module software prompt appears, enter the enable command. If a password has been configured, enter the password at the password: prompt. |
|
Press CTRL-SHIFT-6, and then enter x. |
Module configuration |
From module EXEC mode, enter the configure terminal command. |
|
To return to module EXEC mode from the module configuration mode, use the end or exit command. |
Cisco Unified SIP Proxy EXEC |
From module EXEC mode, enter the cusp command. |
|
To return to module EXEC mode from Cisco Unified SIP Proxy EXEC mode, use the end or exit command. |
Cisco Unified SIP Proxy configuration |
From Cisco Unified SIP Proxy EXEC mode, use the configure command. |
se-10-1-0-0(cusp-config)>
|
To return to Cisco Unified SIP Proxy EXEC mode from Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Accounting |
From Cisco Unified SIP Proxy configuration mode, use the accounting command. |
se-10-1-0-0(cusp-config-
acct)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Policy lookup |
From Cisco Unified SIP Proxy configuration mode, use the policy lookup policy-name command. |
se-10-1-0-0(cusp-config-lookup)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Policy lookup sequence field and sequence header |
From Cisco Unified SIP Proxy policy lookup configuration mode, entering one of the following commands takes you into the sequence field or sequence header configuration modes:
- sequence sequence-number table-name field { in-network | local-address | remote-address }
- sequence sequence-number table-name header { diversion | from | paid | rpid | ruri } uri-component {domain | param name | phone | uri | user}
|
se-10-1-0-0(cusp-config-lookup-
seq)>
|
To return to Cisco Unified SIP Proxy policy lookup configuration mode, use the end or exit command. |
Policy normalization |
From Cisco Unified SIP Proxy configuration mode, use the policy normalization policy_name command. |
se-10-1-0-0(cusp-config-norm)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Policy time |
From Cisco Unified SIP Proxy configuration mode, use the policy time time_policy_name command. |
se-10-1-0-0(cusp-config-time)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Policy time sequence |
From Cisco Unified SIP Proxy policy time configuration mode, use the sequence sequence-number command. |
se-10-1-0-0(cusp-config-time-seq)>
|
To return to Cisco Unified SIP Proxy policy time configuration mode, use the end or exit command. |
RADIUS server group |
From Cisco Unified SIP Proxy configuration mode, use the server-group radius servergroup name [ source-ipaddress ] command. |
se-10-1-0-0(cusp-config-radius)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Route group |
From Cisco Unified SIP Proxy configuration mode, use the route group route-group name [ time-policy ] [ weight ] command. |
se-10-1-0-0(cusp-config-rg)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Element |
From Cisco Unified SIP Proxy route group configuration mode, use the element route-uri or element target-destination command. |
se-10-1-0-0(cusp-config-rg-
element)>
|
To return to Cisco Unified SIP Proxy route group configuration mode, use the end or exit command. |
Route table |
From Cisco Unified SIP Proxy configuration mode, use the route table table_name command. |
se-10-1-0-0(cusp-config-rt)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
SIP DNS server |
From Cisco Unified SIP Proxy configuration mode, use the sipdns-serv command. |
se-10-1-0-0(cusp-config-dns)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
SIP server group |
From Cisco Unified SIP Proxy configuration mode, use the server-group sip servergroup-name command. |
se-10-1-0-0(cusp-config-sg)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
SIP server group ping-options |
From Cisco Unified SIP Proxy configuration mode, use the server-group sip ping-options network ip-address [ port ] command. |
se-10-1-0-0(cusp-config-ping)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
SIP network |
From Cisco Unified SIP Proxy configuration mode, use the sip network network { standard | icmp | noicmp } command. |
se-10-1-0-0(cusp-config-
network)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
SIP queue |
From Cisco Unified SIP Proxy configuration mode, use the sip queue { message | request | st-callback | ct-callback | timer | xcl | radius } command. |
se-10-1-0-0(cusp-config-queue)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Trigger |
From Cisco Unified SIP Proxy configuration mode, use the trigger condition trigger-condition-name command. |
se-10-1-0-0(cusp-config-
trigger)>
|
To return to Cisco Unified SIP Proxy configuration mode, use the end or exit command. |
Trigger sequence |
From trigger configuration mode, use the sequence sequence-number command. |
se-10-1-0-0(cusp-config-
trigger-seq)>
|
To return to Cisco Unified SIP Proxy trigger configuration mode, use the end or exit command. |