Changes in Firmware Version 1.3.6
Hardware and Firmware Compatibility
Behavior During Times of Network Congestion
Documentation, Service Requests, and Additional Information
These Release Notes provide information about Cisco SPA232D Multi-Line DECT ATA and Cisco SPA302D Multi-Line DECT Handset firmware version 1.3.6.
As with any firmware release, read these release notes before you upgrade the firmware. Cisco also recommends that you back up the configuration before you perform any firmware upgrade.
These feature enhancements are added in Firmware Version 1.3.6:
When multiple handsets are using the same DECT line and an incoming call occurs, one handset receives the call, and the missed-call count of the other handset does not increase.
The user can delete the wrong input digits when making an outgoing call.
If a device is upgraded to SW 1.3.3 or later, the provisioning server requests a server certification signed by the Cisco 2K Small Business CA or can use the certificate signed by 1K CA.
Note The 2K server certificate is not compatible with old firmware (before 1.3.3.) The 1K server certificate is compatible with all firmwares, before and after 1.3.3.
Devices with serial number CCQ18230001 (and newer) are built-in with 2K Client Certificate.
For a device with 2K Client Certification, the provisioning server should update the combined CA if client certification is requested.
Note The new combined CA is compatible with both 1K and 2K Client Certification.
The following matrix describes the hardware and firmware compatibility.
Note Do not upgrade any device to an unsupported firmware version as detailed in the Hardware and Firmware Compatibility Matrix table.
Note New SLIC devices have a label that reads S/W: Must use 1.3.5(004p) or later.
Due to CSCug32425, when upgrading the SPA232D loaded with v1.3.1 (or a previous firmware version), it is required to upgrade the SPA232D v1.3.2 firmware twice if provisioning the device via the Upgrade Rule to correctly upgrade to the corresponding embedded SPA302D handset software. A special version of SPA232D firmware has been created to be used to perform the first upgrade while the second upgrade can use SPA232D_SPA302D_1.3.2_014_FW.bin which then installs the SPA302D handset software correctly.
This is not an issue while upgrading the SPA232D firmware via the web-based configuration utility, as the SPA232D needs to be upgraded only once.
Step 1 Download the latest firmware by using the Firmware link on this web page: www.cisco.com/go/smallbizvoicegateways
Step 2 Launch a web browser, and enter the LAN IP addresses of the ATA.
Step 3 Log in to the Configuration Utility. (On first use, enter admin as the username and the password. After logging in, you should configure a unique password that is hard to guess.)
Step 4 Click Administration in the menu bar, and then click Firmware Upgrade in the navigation tree.
Step 5 Click Browse and select the location of the upgrade file that you downloaded.
Step 6 Click the Upgrade button to upgrade the firmware.
Upgrading the firmware may take several minutes. Until the process is complete, DO NOT turn off the power, press the hardware reset button, or click the Back button in your current browser.
Perform this procedure after you upgrade the Cisco SPA232D and are waiting for the ATA to reboot.
Note To verify the upgrade, go to the Administration > Firmware Upgrade page, and confirm that the firmware version number is correct.
Step 1 On the handset, press the center Select button, scroll to Settings, and press the Select button again.
Step 2 In the Settings menu, choose Update Software, and then press the Select button.
Step 3 At the Check for software update prompt, press Confirm.
Step 4 Within a moment, the handset displays the current version of software on the handset and the latest software version available from the Cisco SPA232D. Press the Select softkey.
Step 5 Place the handset in the charging cradle.
The handset erases the flash memory, downloads the new software, and verifies the upgrade data. After the upgrade, a message appears indicating the status of the upgrade (for example, if the upgrade succeeded).
Step 6 After the success message appears, press Reset to reboot the handset.
If the upgrade fails, press Reset to reboot the handset. Check the status lights on the Cisco SPA232D to make sure that it is powered on and functioning. Then repeat the upgrade steps.
Anything that degrades network performance can affect voice and video quality, and in some cases, can cause a call to drop. Sources of network degradation can include, but are not limited to, the following activities:
To reduce or eliminate any adverse effects to the devices, schedule administrative network tasks during a time when the devices are not being used or exclude the devices from testing.
Follow the Release Notes link at www.cisco.com/go/smallbizvoicegateways |
|
Cisco Partner Central for Small Business (Partner Login Required) |
|
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.