Cisco UCS C-Series Servers Integrated Management Controller CLI Configuration Guide, Release 1.5

Viewing Server Properties

Procedure

	Command or Action	Purpose
Step 1	Server# show chassis [detail]	Displays server properties.

This example displays server properties:

Server# show chassis detail
Chassis:
    Power: on
    Serial Number: QCI140205ZG
    Product Name: UCS C210 M2
    PID : R210-2121605W
    UUID: FFFFFFFF-FFFF-FFFF-FFFF-FFFFFFFFFFFF
    Locator LED: off
    Description: 
    Power Restore Policy: power-off
    Power Delay Type: fixed
    Power Delay Value(sec): 0

Server#

Viewing CIMC Properties

Note

CIMC gets the current date and time from the server BIOS. To change this information, reboot the server and press F2 when prompted to access the BIOS configuration menu. Then change the date or time using the options on the main BIOS configuration tab.

Procedure

	Command or Action	Purpose
Step 1	Server# show cimc [detail]	Displays CIMC properties.

This example displays CIMC properties:

Server# show cimc detail
CIMC:
    Firmware Version: 1.4(2.18)
    Current Time: Wed Jan 11 07:01:50 2012
    Boot-loader Version: 1.4(2.18).16

Server#

Viewing CPU Properties

Before You Begin

The server must be powered on, or the properties will not display.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters chassis command mode.
Step 2	Server /chassis # show cpu [detail]	Displays CPU properties.

This example displays CPU properties:

Server# scope chassis
Server /chassis # show cpu
Name         Cores    Version                                            
------------ -------- -------------------------------------------------- 
CPU1         4        Intel(R) Xeon(R) CPU           E5520  @ 2.27GHz    
CPU2         4        Intel(R) Xeon(R) CPU           E5520  @ 2.27GHz    

Server /chassis #

Viewing Memory Properties

Before You Begin

The server must be powered on, or the properties will not display.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters chassis command mode.
Step 2	Server /chassis # show dimm [detail]	Displays memory properties.
Step 3	Server /chassis # show dimm-summary	Displays DIMM summary information.

This example displays memory properties:

Server# scope chassis
Server /chassis # show dimm
Name                 Capacity        Channel Speed (MHz) Channel Type    
-------------------- --------------- ------------------- --------------- 
DIMM_A1              2048 MB         1067                Other           
DIMM_A2              2048 MB         1067                Other           
DIMM_B1              2048 MB         1067                Other           
DIMM_B2              2048 MB         1067                Other           
DIMM_C1              Not Installed   Unknown             Other           
DIMM_C2              Not Installed   Unknown             Other           
DIMM_D1              2048 MB         1067                Other           
DIMM_D2              2048 MB         1067                Other           
DIMM_E1              2048 MB         1067                Other           
DIMM_E2              2048 MB         1067                Other           
DIMM_F1              Not Installed   Unknown             Other           
DIMM_F2              Not Installed   Unknown             Other           

Server /chassis #

This example displays detailed information about memory properties:

Server# scope chassis
Server /chassis # show dimm detail
Name DIMM_A1:
    Capacity: 2048 MB
    Channel Speed (MHz): 1067
    Channel Type: Other
    Memory Type Detail: Synchronous
    Bank Locator: NODE 0 CHANNEL 0 DIMM 0
    Visibility: Yes
    Operability: Operable
    Manufacturer: 0x802C
    Part Number: 18JSF25672PY-1G1D1
    Serial Number: 0xDA415F3F
    Asset Tag: Unknown
    Data Width: 64 bits
Name DIMM_A2:
    Capacity: 2048 MB
--More--   

Server /chassis #

This example displays DIMM summary information:

Server# scope chassis
Server /chassis # show dimm-summary
DIMM Summary:
    Memory Speed: 1067 MHz
    Total Memory: 16384 MB
    Effective Memory: 16384 MB
    Redundant Memory: 0 MB
    Failed Memory: 0 MB
    Ignored Memory: 0 MB
    Number of Ignored Dimms: 0
    Number of Failed Dimms: 0
    Memory RAS possible: Memory configuration can support mirroring
    Memory Configuration: Maximum Performance

Server /chassis #

Viewing Power Supply Properties

Before You Begin

The server must be powered on, or the properties will not display.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters chassis command mode.
Step 2	Server /chassis # show psu [detail]	Displays power supply properties.

This example displays power supply properties:

Server# scope chassis
Server /chassis # show psu
Name       In. Power (Watts)    Out. Power (Watts)   Firmware  Status     
---------- -------------------- -------------------- -------- ---------- 
PSU1       74                   650                  R0E      Present    
PSU2       83                   650                  R0E      Present    

Server /chassis #

Viewing Storage Adapter Properties

Before You Begin

The server must be powered on, or the properties will not display.

Procedure

Command or Action

Purpose

Step 1

Server# scope chassis

Enters the chassis command mode.

Step 2

Server /chassis # show storageadapter [slot] [detail]

Displays installed storage cards.

Note

This command displays all MegaRAID controllers on the server that can be managed through CIMC. If an installed controller or storage device is not displayed, then it cannot be managed through CIMC.

Step 3

Server /chassis # scope storageadapter slot

Enters command mode for an installed storage card.

Step 4

Server /chassis/storageadapter # show bbu [detail]

Displays battery backup unit information for the storage card.

Step 5

Server /chassis/storageadapter # show capabilites [detail]

Displays RAID levels supported by the storage card.

Step 6

Server /chassis/storageadapter # show error-counters [detail]

Displays number of errors seen by the storage card.

Step 7

Server /chassis/storageadapter # show firmware-versions [detail]

Displays firmware version information for the storage card.

Step 8

Server /chassis/storageadapter # show hw-config [detail]

Displays hardware information for the storage card.

Step 9

Server /chassis/storageadapter # show mfg-data [detail]

Displays manufacturer data for the storage card.

Step 10

Server /chassis/storageadapter # show pci-info [detail]

Displays adapter PCI information for the storage card.

Step 11

Server /chassis/storageadapter # show running-firmware-images [detail]

Displays running firmware information for the storage card.

Step 12

Server /chassis/storageadapter # show settings [detail]

Displays adapter firmware settings for the storage card.

Step 13

Server /chassis/storageadapter # show startup-firmware-images [detail]

Displays firmware images to be activated on startup for the storage card.

This example displays storage properties:

Server# scope chassis
Server /chassis # show storageadapter
PCI Slot Product Name                       Serial Number  Firmware Package Build    
-------- ---------------------------------- -------------- ------------------------- 
SAS      LSI MegaRAID SAS 9260-8i           SV93404392     12.12.0-0038                      

          Product ID     Battery Status Cache Memory Size 
     ---- -------------- -------------- -------------- 
          LSI Logic      fully charged  0 MB           

Server /chassis #

This example displays battery backup unit information for the storage card named SAS:

Server# scope chassis
Server /chassis # scope storageadapter SAS
Server /chassis/storageadapter # show bbu
Controller Battery Type Battery Present Voltage    Current    Charge Charging State 
---------- ------------ --------------- ---------- ---------- ------ -------------- 
SAS        iBBU         true            4.051 V    0.000 A    100%   fully charged  

Server /chassis/storageadapter #

Viewing the Flexible Flash Controller Properties

Before You Begin

Cisco Flexible Flash must be supported by your platform.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters the chassis command mode.
Step 2	Server /chassis # show flexflash detail	(Optional) Displays the available Cisco Flexible Flash controllers.
Step 3	Server /chassis # scope flexflash index	Enters the Cisco Flexible Flash controller command mode for the specified controller. At this time, the only permissible index value is FlexFlash-0.
Step 4	Server /chassis/flexflash # show operational-profile detail	Displays the operational profile properties.

This example displays the properties of the flash controller:

Server# scope chassis
Server /chassis # show flexflash
Controller   Product Name     Has Error  Firmware Version  Vendor   Internal State
------------ ---------------- ---------- ----------------- -------- ---------------
FlexFlash-0  Cisco FlexFlash  No         1.2 build 247     Cypress  Connected    

Server /chassis # scope flexflash FlexFlash-0
Server /chassis # show operational-profile
Primary Member Slot  I/O Error Threshold  Host Accessible VDs  
-------------------- -------------------- -------------------- 
slot1                100                  SCU Drivers  

Server /chassis/flexflash #

Viewing Physical Drive Properties

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters the chassis command mode.
Step 2	Server /chassis # scope storageadapter slot	Enters command mode for an installed storage card.
Step 3	Server /chassis/storageadapter # show physical-drive [drive-number] [detail]	Displays physical drive information for the storage card.
Step 4	Server /chassis/storageadapter # show physical-drive-count [detail]	Displays the number of physical drives on the storage card.
Step 5	Server /chassis/storageadapter # scope physical-drive drive-number	Enters command mode for the specified physical drive.
Step 6	Server /chassis/storageadapter/physical-drive # show general [detail]	Displays general information about the specified physical drive.
Step 7	Server /chassis/storageadapter/physical-drive # show inquiry-data [detail]	Displays inquiry data about the specified physical drive.
Step 8	Server /chassis/storageadapter/physical-drive # show status [detail]	Displays status information about the specified physical drive.

This example displays general information about physical drive number 1 on the storage card named SAS:

Server# scope chassis
Server /chassis # scope storageadapter SAS
Server /chassis/storageadapter # scope physical-drive 1
Server /chassis/storageadapter/physical-drive # show general
Slot Number 1:
    Controller: SAS
    Enclosure Device ID: 27
    Device ID: 34
    Sequence Number: 2
    Media Error Count: 0
    Other Error Count: 0
    Predictive Failure Count: 0
    Link Speed: 6.0 Gb/s
    Interface Type: SAS
    Media Type: HDD
    Block Size: 512
    Block Count: 585937500
    Raw Size: 286102 MB
    Non Coerced Size: 285590 MB
    Coerced Size: 285568 MB
    SAS Address 0: 500000e112693fa2
    SAS Address 1: 
    Connected Port 0: 
    Connected Port 1: 
    Connected Port 2: 
    Connected Port 3: 
    Connected Port 4: 
    Connected Port 5: 
    Connected Port 6: 
    Connected Port 7: 
    Power State: powersave

Server /chassis/storageadapter/physical-drive #

This example displays inquiry data about physical drive number 1 on the storage card named SAS:

Server# scope chassis
Server /chassis # scope storageadapter SAS
Server /chassis/storageadapter # scope physical-drive 1
Server /chassis/storageadapter/physical-drive # show inquiry-data
Slot Number 1:
    Controller: SAS
    Product ID: MBD2300RC
    Drive Firmware: 5701
    Drive Serial Number: D010P9A0016D

Server /chassis/storageadapter/physical-drive #

This example displays status information about physical drive number 1 on the storage card named SAS:

Server# scope chassis
Server /chassis # scope storageadapter SAS
Server /chassis/storageadapter # scope physical-drive 1
Server /chassis/storageadapter/physical-drive # show inquiry-data
Slot Number 1:
    Controller: SAS
    State: online
    Online: true
    Fault: false

Server /chassis/storageadapter/physical-drive #

Viewing Virtual Drive Properties

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters the chassis command mode.
Step 2	Server /chassis # scope storageadapter slot	Enters command mode for an installed storage card.
Step 3	Server /chassis/storageadapter # show virtual-drive [drive-number] [detail]	Displays virtual drive information for the storage card.
Step 4	Server /chassis/storageadapter # show virtual-drive-count [detail]	Displays the number of virtual drives configured on the storage card.
Step 5	Server /chassis/storageadapter # scope virtual-drive drive-number	Enters command mode for the specified virtual drive.
Step 6	Server /chassis/storageadapter/virtual-drive # show physical-drive [detail]	Displays physical drive information about the specified virtual drive.

This example displays information about virtual drives on the storage card named SAS:

Server# scope chassis
Server /chassis # scope storageadapter SAS
Server /chassis/storageadapter # show virtual-drive
Virtual Drive  Status          Name                     Size       RAID Level 
-------------- --------------- ------------------------ ---------- ---------- 
0              Optimal         SLES1SP1beta5            30720 MB   RAID 0     
1              Optimal         RHEL5.5                  30720 MB   RAID 0     
2              Optimal         W2K8R2_DC                30720 MB   RAID 0     
3              Optimal         VD_3                     30720 MB   RAID 0     
4              Optimal         ESX4.0u2                 30720 MB   RAID 0     
5              Optimal         VMs                      285568 MB  RAID 0     
6              Optimal         RHEL6-35GB               35840 MB   RAID 0     
7              Optimal         OS_Ins_Test_DR           158720 MB  RAID 0     
8              Optimal                                  285568 MB  RAID 1        

Server /chassis/storageadapter #

This example displays physical drive information about virtual drive number 1 on the storage card named SAS:

Server# scope chassis
Server /chassis # scope storageadapter SAS
Server /chassis/storageadapter # scope virtual-drive 1
Server /chassis/storageadapter/virtual-drive # show physical-drive
Span  Physical Drive Status     Starting Block Number Of Blocks 
----- -------------- ---------- -------------- ---------------- 
0     12             online     62914560       62914560         

Server /chassis/storageadapter/virtual-drive #

Viewing Nvidia GPU Card Information

These commands are not available on all UCS C-series servers.

Before You Begin

The server must be powered on to view information on the Nvidia GPU cards.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters the chassis command mode.
Step 2	Server /chassis # show gpu	Displays the available Nvidia GPU cards on the system.
Step 3	Server /chassis # scope gpu slot-number	Enters the GPU card command mode. Specify the slot number of the GPU card.
Step 4	Server /chassis/gpu # show gpu-list	Displays temperature information on the GPU cards.

This example shows how to view the temperature information of the available GPU cards on the system:

Server # scope chassis
Server /chassis # show gpu

Slot       Product Name         Num of GPUs
----       ------------         -----------
5          Nvidia GRID K2 @ BD     2

Server /chassis # scope gpu 5
Server /chassis/gpu # show gpu-list

GPU ID       Temperature
------       -----------
0             32
1             33

Server /chassis/gpu #

Viewing PCI Adapter Properties

Before You Begin

The server must be powered on, or the properties will not display.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters the chassis command mode.
Step 2	Server /chassis # show pci-adapter [detail]	Displays PCI adapter properties.

This example displays PCI adapter properties:

Server# scope chassis
Server /chassis # show pci-adapter
Name             Slot  Vendor ID    Device ID    Product Name              
---------------- ----- ------------ ------------ ------------------------- 
PCIe Adapter1    1     0x1137       0x0042       Cisco UCS P81E Virtual... 
PCIe Adapter2    5     0x1077       0x2432       Qlogic QLE2462 4Gb dua... 

Server /chassis #

Viewing LOM Properties

You can view the MAC addresses of the LAN On Motherboard (LOM) Ethernet ports.

Procedure

	Command or Action	Purpose
Step 1	Server# scope chassis	Enters the chassis command mode.
Step 2	Server /chassis # scope network-adapter slot ID	Enters the specific network adapter command mode.
Step 3	Server /chassis/network-adapter # show mac-list [detail]	Displays the MAC addresses of the LOM ports.

This example shows how to display the MAC addresses of the LOM ports:

Server# scope chassis
Server /chassis # scope network-adapter L
Server /chassis/network-adapter # show mac-list
Interface ID       MAC Address
-------------  --------------------
eth0            010000002000
eth1            010000002000

Server /chassis/network-adapter #

Bias-Free Language

Book Title

Viewing Server Properties

Results

Chapter: Viewing Server Properties

Viewing Server Properties

Viewing Server Properties

Viewing CIMC Properties

Viewing CPU Properties

Viewing Memory Properties

Viewing Power Supply Properties

Viewing Storage Adapter Properties

Viewing the Flexible Flash Controller Properties

Viewing Physical Drive Properties

Viewing Virtual Drive Properties

Viewing Nvidia GPU Card Information

Viewing PCI Adapter Properties

Viewing LOM Properties

Was this Document Helpful?

Contact Cisco