Step 1
|
Log into the
Hyper-V host.
|
Step 2
|
Choose
to open
Hyper-V Manager.
|
Step 3
|
In the
Hyper-V
Manager dialog box, choose
.
|
Step 4
|
In the
Before
You Begin pane, choose the custom configuration option and click
Next.
|
Step 5
|
In the
Specify
Name and Location pane, in the
Name field, edit the VM name and click
Next.
|
Step 6
|
In the
Specify
Name and Location pane, check the
Store
the virtual machine in a different location checkbox and specify
the alternate location or the virtual machine is stored in the default folder.
|
Step 7
|
Click
Next.
|
Step 8
|
In the
Assign
Memory pane, enter the amount of memory to allocate to this VM
(recommended12 GB) and click
Next.
|
Step 9
|
In the
Configure Networking pane, do not make any changes to
the settings specified for the
Connection field and click
Next.
|
Step 10
|
In the
Connect
Virtual Hard Disk pane, select use an existing virtual hard disk or
attach a virtual hard disk later and click
Next.
|
Step 11
|
Click
Next.
|
Step 12
|
In the
Completing the New Virtual Machine Wizard pane,
verify the settings and click
Finish.
|
Step 13
|
In the
Hyper-V
Manager pane, right-click the new VM and choose
Settings.
|
Step 14
|
In the
Navigation pane, choose
IDE
Controller 0.
|
Step 15
|
In
the IDE
Controller pane, choose
Hard
Drive and click
Add.
Note
|
You need to add two hard drives as there are two separate VHD files - one for the OS and application, and the other for the
database.
|
|
Step 16
|
In the
Hard
Drive pane, click
Browse, choose the downloaded
Cisco IMC Supervisor
.vhd file and click
Open.
|
Step 17
|
Click
Apply.
|
Step 18
|
Review the
virtual hard drive properties.
|
Step 19
|
In the
Navigation pane, choose
Memory.
|
Step 20
|
In the
Memory pane, enter the recommended value (minimum 12
GB) and drag the
Memory
weight to
High.
|
Step 21
|
In the
Navigation pane, choose
Processor.
|
Step 22
|
In the
Processor pane, choose the recommended value (4 vCPU)
and in the
Resource Control pane, enter 100 in the
Virtual machine reserve (percentage) field.
|
Step 23
|
In the
Navigation pane, choose
Network Adapter.
|
Step 24
|
Click
Remove to remove the network adapter that was
created when you created the new VM.
|
Step 25
|
In the
Navigation pane, choose
Add
Hardware.
|
Step 26
|
In the
Add
Hardware pane, choose
Legacy
Network Adapter and click
Add.
|
Step 27
|
In the
Legacy
Network Adapter pane, in the
Network field, choose
Local
Area Connection - Virtual Network and click
Apply.
|
Step 28
|
Verify that
you have sufficient vCPU and Memory resources allocated.
For the minimum system requirements, see Minimum System Requirements.
|
Step 29
|
Click
OK.
|
Step 30
|
Power on the
VM.
|
Step 31
|
Optionally,
you can configure network properties from the shelladmin. For more information
about configuring network properties, see
Configuring the Network Interface using Shelladmin.
|
Step 32
|
After the
appliance restarts, copy and paste the
Cisco IMC Supervisor
IP address that is displayed into a supported web browser to access the
Login page.
|
Step 33
|
At the login
prompt, enter
admin for username and
admin for the password to log into
Cisco IMC Supervisor.
Note
|
Change your
administrator password after this initial login.
|
|