- About This Guide
- Preparing for Configuration
- Configuring General Switch Features
- Provisioning PXM1E Communication Links
- Preparing Service Modules for Communication
- Preparing SRM Cards for Communications
- Preparing RPM Cards for Operation
- Managing Service Class Templates
- Managing PNNI Nodes and PNNI Routing
- Switch Operating Procedures
- Switch Maintenance Procedures
- Viewing and Responding to Alarms
- Downloading and Installing Software Upgrades
- Supporting and Using Additional CLI Access Options
- PXM Backup Boot Procedures
- Standards Compliance
- Hardware Survey and Software Configuration Worksheets
- MPSM Licensing
- RAS Features
Cisco MGX 8800/8900 Series Configuration Guide, Release 5.2
Chapter: Hardware Survey and Software Configuration Worksheets
- Hardware Survey Worksheets
- General MGX Switch Configuration Worksheet (PXM45, PXM1E, and SRM)
- Additional PXM1E Information Configuration Worksheet
- AUSM/B Configuration Worksheet
- AXSM Configuration Worksheet
- CESM Configuration Worksheet
- FRSM-12-T3E3 Configuration Worksheet
- FRSM-2CT3, FRSM-2T3E3, and FRSM-HS2/B Configuration Worksheet
- FRSM-8T1 and FRSM-8E1 Configuration Worksheet
- MPSM-8-T1E1 Configuration Worksheet
- MPSM-T3E3-155 Configuration Worksheet
- MPSM-16-T1E1 Configuration Worksheet
- VISM Configuration Worksheet
- VXSM Configuration Worksheet
Hardware Survey and Software Configuration Worksheets
The worksheets in this chapter serve as a place to record the hardware installed in your switch and the configuration planning decisions you make as you plan your software configuration. Instructions for filling out the Hardware Survey worksheets appear in the "Verifying the Hardware Configuration" section of Chapter 2, "Configuring General Switch Features."
The information you need to complete the software configuration worksheets appears in "Preparing for Configuration" and in the Cisco MGX 8800/8900 Hardware Installation Guide, Releases 2 - 5.2.
Cisco recommends that you make copies of these tables and fill them out for each card on your switch as applicable. For example, if you have seven CESM cards on your MGX 8850 (PXM1E) switch, you should fill out the MGX 8850 hardware survey worksheet once and the CESM worksheet in Table E-8 seven times.
Once you have filled out the appropriate worksheets for your MGX switch, you can refer back to them to obtain information you need to complete configuration on your switch. You can also refer to these worksheets to troubleshoot and modify the configuration of your MGX switch in the future.
Note 
You only need to complete the worksheets that apply to your switch and the cards you installed on your switch.
Hardware Survey Worksheets
The hardware survey worksheets provide space for you to note the types of front and back cards installed in your switch and the redundancy relationships between them. The primary purpose of the survey worksheet is to document which cards are installed in the switch and give you a chance to validate that cards are installed in the correct locations and that back cards are compatible with front cards. The "Verifying the Hardware Configuration" section of Chapter 2, "Configuring General Switch Features," describes how to use the switch software to locate the information needed in the hardware survey worksheets.
Note The hardware survey worksheets do not contain all the information you need to configure the switch. Use the hardware survey worksheets to identify the hardware and validate the hardware installation. Use the software configuration worksheets in this chapter to plan the configuration for each card. You can validate the hardware first, or complete your configuration plan first. However, the configuration will not work correctly until the hardware installed matches the software configuration plan.
Table E-1, Table E-2, and Table E-3 serve as the hardware survey worksheets for the three types of Cisco MGX switches.
General MGX Switch Configuration Worksheet (PXM45, PXM1E, and SRM)
Table E-4 lists general switch parameters you can configure in each new switch.
|
|
|
|
|---|---|---|
Switch name |
Text |
|
IP Addresses |
||
Boot IP address information |
Primary card address |
|
Secondary card address |
|
|
Network mask |
|
|
Disk or LAN IP address information |
IP address |
|
Network mask |
|
|
IP address information for access over ATM |
IP address |
|
Network mask |
|
|
SLIP IP address information |
IP address |
|
Network mask |
|
|
ATM Address and PNNI Configuration Data |
||
PNNI controller |
Controller ID |
2 |
Controller type |
2 (PNNI) |
|
Controller name |
|
|
PNNI level and lowest peer group ID |
Refer to the Cisco PNNI Network Planning Guide for MGX and SES Products. |
|
PNNI node address |
Refer to the Cisco PNNI Network Planning Guide for MGX and SES Products. |
|
SPVC prefix |
Refer to the Cisco PNNI Network Planning Guide for MGX and SES Products. |
|
MPLS controller |
Controller ID |
3 |
Controller type |
3 (LSC) |
|
Controller name |
|
|
Administrator data |
||
User cisco |
Password |
|
User service |
Password |
|
User superuser |
Password |
|
Additional user |
User name |
|
Password |
|
|
Access level |
|
|
Additional user |
User name |
|
Password |
|
|
Access level |
|
|
Additional user |
User name |
|
Password |
|
|
Access level |
|
|
Network Clock Source Plan |
||
Manual clock configuration |
Primary clock source |
|
Secondary clock source |
|
|
NCDP |
Enabled or disabled? |
|
NCDP clock source |
Port ID |
|
Primary reference source |
|
|
Clock type |
|
|
Priority |
|
|
Stratum level |
|
|
NCDP clock source |
Port ID |
|
Primary reference source |
|
|
Clock type |
|
|
Priority |
|
|
Stratum level |
|
|
Network Management Plan |
||
SNMP access |
Community |
|
Contact |
|
|
Location |
|
|
Software Version Data |
||
Boot software |
Version number |
|
Runtime software |
Version number |
|
Time Zone Data |
||
Time zone |
Enter a zone |
|
Time zone offset |
Hours to offset |
|
PXM and SRM1 Redundancy Options |
||
Standalone configuration |
Primary or secondary card set installed? |
|
Upper bay SRM |
SRM-3T3 or SRME? |
|
Bulk distribution? |
|
|
Lower bay SRM |
SRM-3T3 or SRME? |
|
Bulk distribution? |
|
|
Redundant configuration |
|
|
Upper bay SRMs |
SRM-3T3 or SRME? |
|
Bulk distribution? |
|
|
SRM line redundancy? |
|
|
Lower bay SRMs |
SRM-3T3 or SRME? |
|
Bulk distribution? |
|
|
SRM line redundancy? |
|
|
1 SRM cards do not operate in Cisco MGX 8950 switches. |
Additional PXM1E Information Configuration Worksheet
Table E-5 lists the additional information you will need to configure PXM1E cards.
Note PXM1E cards operate only on MGX 8850 (PXM1E), Cisco MGX 8850/B, Cisco MGX 8830, and Cisco MGX 8830/B switches. If you are configuring a MGX 8850 (PXM45) or MGX 8950 switch, you do not need to fill out Table E-5.
|
|
|
|
|---|---|---|
Card type |
Front and back cards installed |
|
Standalone configuration |
Using intracard APS? |
|
Redundant configuration |
APS connector installed? |
|
Card SCT |
SCT number |
|
Line operation mode |
T1, E1, T3, or E3? |
|
Line 1 Redundancy Options1 |
||
Intracard APS |
Working index2 |
slot.2.1 |
Protection index2 |
slot.2.2 |
|
Mode3 |
|
|
Intercard APS |
Working index4 |
slot.2.1 |
Protection index5 |
slot.2.1 |
|
Mode6 |
|
|
Line 2 Redundancy Options1 |
||
Intracard APS |
Configured while configuring line 1 |
|
Intercard APS |
Working index4 |
slot.2.2 |
Protection index5 |
slot.2.2 |
|
Mode6 |
|
|
Line 3 Redundancy Options1 |
||
Intracard APS |
Working index2 |
slot.2.3 |
Protection index2 |
slot.2.4 |
|
Mode3 |
|
|
Intercard APS |
Working index4 |
slot.2.3 |
Protection index5 |
slot.2.3 |
|
Mode6 |
|
|
Line 4 Redundancy Options1 |
||
Intracard APS |
Configured while configuring line 3 |
|
Intercard APS |
Working index4 |
slot.2.4 |
Protection index5 |
slot.2.4 |
|
Mode6 |
|
|
Line 5 Redundancy Options1 |
||
Intracard APS |
Working index2 |
slot.2.5 |
Protection index2 |
slot.2.6 |
|
Mode3 |
|
|
Intercard APS |
Working index4 |
slot.2.5 |
Protection index5 |
slot.2.5 |
|
Mode6 |
|
|
Line 6 Redundancy Options1 |
||
Intracard APS |
Configured while configuring line 5 |
|
Intercard APS |
Working index4 |
slot.2.6 |
Protection index5 |
slot.2.6 |
|
Mode6 |
|
|
Line 7 Redundancy Options1 |
||
Intracard APS |
Working index2 |
slot.2.7 |
Protection index2 |
slot.2.8 |
|
Mode3 |
|
|
Intercard APS |
Working index4 |
slot.2.7 |
Protection index5 |
slot.2.7 |
|
Mode6 |
|
|
Line 8 Redundancy Options1 |
||
Intracard APS |
Configured while configuring line 7 |
|
Intercard APS |
Working index4 |
slot.2.8 |
Protection index5 |
slot.2.8 |
|
Mode6 |
|
|
Line 9 Redundancy Options1 |
||
Intracard APS |
Working index2 |
slot.2.9 |
Protection index2 |
slot.2.10 |
|
Mode3 |
|
|
Intercard APS |
Working index4 |
slot.2.9 |
Protection index5 |
slot.2.9 |
|
Mode6 |
|
|
Line 10 Redundancy Options1 |
||
Intracard APS |
Configured while configuring line 9 |
|
Intercard APS |
Working index4 |
slot.2.10 |
Protection index5 |
slot.2.10 |
|
Mode6 |
|
|
Line 11 Redundancy Options1 |
||
Intracard APS |
Working index2 |
slot.2.11 |
Protection index2 |
slot.2.12 |
|
Mode3 |
|
|
Intercard APS |
Working index4 |
slot.2.11 |
Protection index5 |
slot.2.11 |
|
Mode6 |
|
|
Line 12 Redundancy Options1 |
||
Intracard APS |
Configured while configuring line 11 |
|
Intercard APS |
Working index4 |
slot.2.12 |
Protection index5 |
slot.2.12 |
|
Mode6 |
|
|
1 APS can only be configured on optical lines. For PXM1E-4-155, APS can be configured on lines 1 through 4, and on PXM1E-8-155, APS can be configured on lines 1 through 8. On PXM1E-COMBO, APS can be configured on lines 9 through 12. 2 Enter the slot number for the standalone PXM1E, which is 1 or 2 on Cisco MGX 8830 and 7 or 8 on MGX 8850 (PXM1E). 3 Valid options: 1+1, 1:1, annexB 1+1, or straight cable 1+1 4 Enter the slot number of the primary PXM1E, which is 1 on Cisco MGX 8830 and 7 on MGX 8850 (PXM1E). 5 Enter the slot number of the secondary PXM1E, which is 2 on Cisco MGX 8830 and 8 on MGX 8850 (PXM1E). 6 Valid options: 1+1, annexB 1+1, or straight cable 1+1 |
AUSM/B Configuration Worksheet
Table E-6 lists general switch parameters you will need to configure on each AUSM/B card.
Note AUSM/B cards operate only on MGX 8850 (PXM1E) and Cisco MGX 8830 switches. If you are configuring a MGX 8850 (PXM45) or MGX 8950 switch, or if you do not have AUSM/B cards installed in your switch, you do not need to complete the worksheet in Table E-6
AXSM Configuration Worksheet
Table E-7 lists general switch parameters you will need to configure on each AXSM card.
Note AXSM cards operate only on MGX 8850 (PXM45) and MGX 8950 switches, and on the Cisco MGX 8880 Media Gateway. AXSM-E cards operate on Cisco MGX 8850/B and Cisco MGX 8830/B. The Cisco MGX 8800/8900 Hardware Installation Guide, Releases 2 - 5.2 describes which AXSM cards operate in which switches. If you are configuring a MGX 8850 (PXM1E) or Cisco MGX 8830 switch, or if you do not have AXSM cards installed in your switch, you do not need to fill out Table E-7.
CESM Configuration Worksheet
Table E-8 lists general switch parameters you will need to configure on each CESM card.
Note CESM cards do not operate in MGX 8950 switches. If you are configuring a MGX 8950 switch, or if you do not have CESM cards installed in your switch, you do not need to complete the worksheet in Table E-8.
FRSM-12-T3E3 Configuration Worksheet
Table E-9 lists general switch parameters you will need to configure on each FRSM-12-T3E3 card.
Note FRSM12 cards operate only on MGX 8850 (PXM45) switches. If you are configuring a MGX 8850 (PXM1E), Cisco MGX 8830, or MGX 8950 switch, or if you do not have FRSM12 cards installed in your switch, you do not need to complete the worksheet in Table E-9.
FRSM-2CT3, FRSM-2T3E3, and FRSM-HS2/B Configuration Worksheet
Table E-11 lists general switch parameters you will need to configure the FRSM-2CT3, FRSM-2T3E3, and FRSM-HS2/B cards.
Note If you are configuring a MGX 8950 switch, or if you do not have FRSM-2CT3, FRSM-2T3E3, and FRSM-HS2/B cards installed in your switch, you do not need to complete the worksheet in Table E-10.
FRSM-8T1 and FRSM-8E1 Configuration Worksheet
Table E-11 lists general switch parameters you will need to configure channelized and non-channelized 8-port FRSM cards.
Note If you are configuring a MGX 8950 switch, or if you do not have 8-port FRSM cards installed in your switch, you do not need to complete the worksheet in Table E-11.
MPSM-8-T1E1 Configuration Worksheet
Table E-12 lists general switch parameters you will need to configure channelized and non-channelized 8-port MPSM cards.
Note If you are configuring a Cisco MGX 8880 Media Gateway or a MGX 8950 switch, or if you do not have 8-port MPSM cards installed in your switch, you do not need to complete the worksheet in Table E-12.
MPSM-T3E3-155 Configuration Worksheet
Table E-13 lists general switch parameters you will need to configure on each MPSM-T3E3-155 card.
MPSM-16-T1E1 Configuration Worksheet
Table E-14 lists general switch parameters you will need to configure on each MPSM-16-T1E1 card.
VISM Configuration Worksheet
Table E-15 lists general switch parameters you will need to configure on each VISM card.
Note VISM cards do not operate in MGX 8950 switches. If you are configuring a MGX 8950 switch, or if you do not have VISM cards installed in your switch, you do not need to complete the worksheet in Table E-15.
VXSM Configuration Worksheet
Table E-16 lists general switch parameters you will need to configure on each VXSM card.
Note VXSM cards operate only on MGX 8850 (PXM45) and MGX 8950 switches. If you are configuring a MGX 8850 (PXM1E) or Cisco MGX 8830 switch, or if you do not have VXSM cards installed in your switch, you do not need to fill out Table E-16.
Feedback