- Index
- Preface
- Overview
- Using the Command-Line Interface
- Assigning the Switch IP Address and Default Gateway
- Configuring Cisco IOS Configuration Engine
- Administering the Switch
- Configuring Switch Alarms
- Configuring SDM Templates
- Configuring Switch-Based Authentication
- Configuring IEEE 802.1x Port-Based Authentication
- Configuring Interface Characteristics
- Configuring Command Macros
- Configuring VLANs
- Configuring Private VLANs
- Configuring IEEE 802.1Q and Layer 2 Protocol Tunneling
- Configuring STP
- Configuring MSTP
- Configuring Optional Spanning-Tree Features
- Configuring Resilient Ethernet Protocol
- Configuring Flex Links and the MAC Address-Table Move Update Feature
- Configuring DHCP Features and IP Source Guard
- Configuring Dynamic ARP Inspection
- Configuring IGMP Snooping and MVR
- Configuring Port-Based Traffic Control
- Configuring CDP
- Configuring LLDP and LLDP-MED
- Configuring UDLD
- Configuring SPAN and RSPAN
- Configuring RMON
- Configuring System Message Logging
- Configuring SNMP
- Configuring Embedded Event Manager
- Configuring Network Security wit
- Configuring Control-Plane Security
- Configuring QoS
- Configuring EtherChannels and Link State Tracking
- Configuring IP Unicast Routing
- Configuring IPv6 Unicast Routing
- Configuring IPv6 MLD Snooping
- Configuring IPv6 ACLs
- Configuring HSRP, VRRP, and GLBP
- Configuring Cisco IOS IP SLAs Operations
- Configuring Enhanced Object Tracking
- Configuring Ethernet OAM, CFM, and E-LMI
- Configuring IP Multicast Routing
- Configuring MSDP
- Troubleshooting
- Configuring Online Diagnostics
- Working with the Cisco IOS File System, Configuration Files, and Software Images
- Unsupported Commands in Cisco IOS Release 12.2(58)SE
- Access Control Lists
- ARP Commands
- Boot Loader Commands
- CGMP Commands
- Debug Commands
- Embedded Event Manager
- Embedded Syslog Manager
- HSRP
- IEEE 802.1x
- IGMP Snooping Commands
- Interface Commands
- IP Multicast Routing
- IP Unicast Routing
- MAC Address
- Miscellaneous
- MSDP
- NetFlow
- QoS
- RADIUS
- SNMP
- Spanning Tree
- Storm Control
- VLAN
Unsupported Commands in Cisco IOS Release 12.2(58)SE
This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Cisco ME 3400E Ethernet Access switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. The unsupported commands are listed by software feature and command mode.
Access Control Lists
Unsupported Privileged EXEC Commands
access-enable [host] [timeout minutes]
access-template [access-list-number | name] [dynamic-name] [source] [destination] [timeout minutes]
clear access-template [access-list-number | name] [dynamic-name] [source] [destination].
Unsupported Global Configuration Commands
access-list rate-limit acl-index {precedence | mask prec-mask}
access-list dynamic extended
ARP Commands
Unsupported Global Configuration Commands
arp ip-address hardware-address smds
arp ip-address hardware-address srp-a
arp ip-address hardware-address srp-b
Unsupported Interface Configuration Commands
arp probe
ip probe proxy
Boot Loader Commands
Unsupported Privileged EXEC Command
clear ip cgmp
Unsupported Interface Configuration Command
ip cgmp
CGMP Commands
Unsupported User EXEC Command
verify
Unsupported Global Configuration Command
boot buffersize
Debug Commands
debug dot1x feature
debug platform cli-redirection main
debug platform configuration
debug qos
Embedded Event Manager
Unsupported Privileged EXEC Commands
event manager update user policy [policy-filename | group [group name expression] ] | repository [url location]
Parameters are not supported for this command:
event manager run [policy name] |<paramater1>|... <paramater15>|
Unsupported Global Configuration Commands
no event manager directory user repository [url location]
event manager applet [applet-name] maxrun
Unsupported Commands in Applet Configuration Mode
no event interface name [interface-name] parameter [counter-name] entry-val [entry counter value] entry-op {gt | ge | eq | ne |lt | le} [entry-type {increment | rate | value] [exit-val [exit value] exit-op {gt | ge | eq | ne |lt | le} exit-type { increment | rate | value}][average-factor <average-factor-value>]
no trigger
tag
Embedded Syslog Manager
Unsupported Global Configuration Commands
All
Unsupported Privileged EXEC Commands
All
HSRP
Unsupported Global Configuration Commands
interface Async
interface BVI
interface Dialer
interface Group-Async
interface Lex
interface Multilink
interface Virtual-Template
interface Virtual-Tokenring
Unsupported Interface Configuration Commands
mtu
standby mac-refresh seconds
standby use-bia
IEEE 802.1x
Unsupported Global Configuration Command
dot1x critical
Unsupported Interface Configuration Commands
dot1x auth-fail
dot1x control-direction
dot1x critical
dot1x host-mode multi-domain
dot1x mac-auth-bypass
dot1x pae
Note The switch does not support the IEEE 802.1x MAC authentication bypass or guest VLAN features.
Unsupported Privileged EXEC Commands
clear dot1x
clear eap sessions
show eap
Unsupported Global Configuration Command
dot1x critical {eapol | recovery delay ms}
Unsupported Interface Configuration Commands
dot1x auth-fail {max-attempts number| vlan vlan-id}
dot1x control-direction {both | in}
dot1x critical [recovery action reinitialize | vlan vlan-id}
dot1x control-direction {both | in}
dot1x mac-auth-bypass
dot1x mac-reauth-req
dot1x pae
dot1x timeout rate-limit period
IGMP Snooping Commands
Unsupported Global Configuration Commands
ip igmp snooping source-only-learning
Interface Commands
Unsupported Privileged EXEC Commands
show interfaces [interface-id | vlan vlan-id] [crb | fair-queue | irb | mac-accounting | precedence | irb | random-detect | rate-limit | shape]
Unsupported Global Configuration Commands
interface tunnel
Unsupported Interface Configuration Commands
transmit-interface type number
IP Multicast Routing
Unsupported Privileged EXEC Commands
clear ip rtp header-compression [type number]
clear ip dvmrp route commands
debug ip dvmrp commands
The debug ip packet command displays packets received by the switch CPU. It does not display packets that are hardware-switched.
The debug ip mcache command affects packets received by the switch CPU. It does not display packets that are hardware-switched.
The debug ip mpacket [detail] [access-list-number [group-name-or-address] command affects only packets received by the switch CPU. Because most multicast packets are hardware-switched, use this command only when you know that the route will forward the packet to the CPU.
debug ip pim atm
show frame-relay ip rtp header-compression [interface type number]
show ip dvmrp route commands
The show ip mcache command displays entries in the cache for those packets that are sent to the switch CPU. Because most multicast packets are switched in hardware without CPU involvement, you can use this command, but multicast packet information is not displayed.
The show ip mpacket commands are supported but are only useful for packets received at the switch CPU. If the route is hardware-switched, the command has no effect because the CPU does not receive the packet and cannot display it.
show ip pim vc [group-address | name] [type number]
show ip rtp header-compression [type number] [detail]
Unsupported Global Configuration Commands
All ip dvmrp commands
ip pim accept-rp {address | auto-rp} [group-access-list-number]
ip pim message-interval seconds
ip pim register-rate-limit
Unsupported Interface Configuration Commands
frame-relay ip rtp header-compression [active | passive]
frame-relay map ip ip-address dlci [broadcast] compress
frame-relay map ip ip-address dlci rtp header-compression [active | passive]
All ip dvmrp commands
ip igmp helper-address ip-address
ip multicast helper-map {group-address | broadcast} {broadcast-address | multicast-address} extended-access-list-number
ip multicast rate-limit {in | out} [video | whiteboard] [group-list access-list] [source-list access-list] kbps
ip multicast ttl-threshold ttl-value (instead, use the ip multicast boundary access-list-number interface configuration command)
ip multicast use-functional
ip pim minimum-vc-rate pps
ip pim multipoint-signalling
ip pim nbma-mode
ip pim vc-count number
ip rtp compression-connections number
ip rtp header-compression [passive]
IP Unicast Routing
Unsupported Privileged EXEC or User EXEC Commands
clear ip accounting [checkpoint]
clear ip bgp address flap-statistics
clear ip bgp prefix-list
debug ip cef stats
show cef [drop | not-cef-switched]
show ip accounting [checkpoint] [output-packets | access-violations]
show ip bgp dampened-paths
show ip bgp inconsistent-as
show ip bgp regexp regular expression
show ipv6 (all)
Unsupported Global Configuration Commands
ip accounting-list ip-address wildcard
ip accounting-transits count
ip cef accounting [per-prefix] [non-recursive]
ip cef traffic-statistics [load-interval seconds] [update-rate seconds]]
ip flow-aggregation
ip flow-cache
ip flow-export
ip gratuitous-arps
ip local
ip reflexive-list
router egp
router-isis
router iso-igrp
router mobile
router odr
router static
Unsupported Interface Configuration Commands
dampening
ip load-sharing [per-packet]
ip accounting
ip load-sharing [per-packet]
ip mtu bytes
ip ospf dead-interval minimal hello-multiplier multiplier
ip verify
ip unnumbered type number
All ip security commands
Unsupported BGP Router Configuration Commands
address-family vpnv4
default-information originate
neighbor advertise-map
neighbor allowas-in
neighbor default-originate
neighbor description
network backdoor
table-map
Unsupported VPN Configuration Commands
All
Unsupported Route Map Commands
match route-type for policy-based routing (PBR)
set as-path {tag | prepend as-path-string}
set automatic-tag
set dampening half-life reuse suppress max-suppress-time
set default interface interface-id [interface-id.....]
set interface interface-id [interface-id.....]
set ip default next-hop ip-address [ip-address.....]
set ip destination ip-address mask
set ip precedence value
set ip qos-group
set metric-type internal
set origin
set metric-type internal
MAC Address
Unsupported Privileged EXEC Commands
show mac-address-table
show mac-address-table address
show mac-address-table aging-time
show mac-address-table count
show mac-address-table dynamic
show mac-address-table interface
show mac-address-table multicaset
show mac-address-table notification
show mac-address-table static
show mac-address-table vlan
show mac address-table multicast
Note Use the show ip igmp snooping groups privileged EXEC command to display Layer 2 multicast address-table entries for a VLAN.
Unsupported Global Configuration Commands
mac-address-table aging-time
mac-address-table notification
mac-address-table static
Miscellaneous
Unsupported User EXEC Commands
verify
Unsupported Privileged EXEC Commands
archive config
file verify auto
remote command all
show archive config
show archive log
show cable-diagnostics prbs
show power inline
test cable-diagnostics prbs
Unsupported Global Configuration Commands
exception crashinfo
errdisable detect cause dhcp-rate-limit
errdisable recovery cause dhcp-rate-limit
errdisable recovery cause unicast flood
l2protocol-tunnel global drop-threshold
memory reserve critical
power inline consumption default wattage
service compress-config
stack-mac persistent timer
track object-number rtr
Unsupported show platform Commands
show platform ip unicast vrf {compaction | tcam-label}
show platform ipv6 unicast
show platform tb
MSDP
Unsupported Privileged EXEC Commands
show access-expression
show exception
show location
show pm LINE
show smf [interface-id]
show subscriber-policy [policy-number]
show template [template-name]
Unsupported Global Configuration Commands
ip msdp default-peer ip-address | name [prefix-list list] (Because BGP/MBGP is not supported, use the ip msdp peer command instead of this command.)
NetFlow
Unsupported Global Configuration Commands
ip flow-aggregation cache
ip flow-cache entries
ip flow-export
QoS
Unsupported Global Configuration Command
priority-list
Unsupported Interface Configuration Command
priority-group
Unsupported policy-map Class Police Configuration Mode Command
conform-color class-map police configuration
RADIUS
Unsupported Global Configuration Commands
aaa authentication feature default enable
aaa authentication feature default line
aaa nas port extended
authentication command bounce-port ignore
authentication command disable-port ignore
radius-server attribute nas-port
radius-server configure
radius-server extended-portnames
SNMP
Unsupported Global Configuration Commands
snmp-server enable informs
snmp-server ifindex persist
logging discriminator discr-name [[facility] [mnemonics] [msg-body] {drops string | includes string}] [severity {drops sev-num | includes sev-num}] [rate-limit msglimit]
logging buffered discriminator
Spanning Tree
Unsupported Global Configuration Command
spanning-tree pathcost method {long | short}
spanning-tree transmit hold-count
Unsupported Interface Configuration Command
spanning-tree stack-port
Storm Control
Note Although visible in the command line interface, commands for configuring small-frame thresholds are not needed on the switch because the existing broadcast storm disable feature correctly handles small frames.
Unsupported Global Configuration Command
errdisable detect cause small-frame
errdisable recovery cause small-frame
Unsupported Interface Configuration Command
small-frame violation rate
VLAN
Unsupported Global Configuration Command
vlan internal allocation policy {ascending | descending}
Unsupported User EXEC Commands
show running-config vlan
show vlan ifindex
vlan database
Unsupported VLAN Database Commands
vtp
vlan