Supported MIBs
This appendix lists the supported management information base (MIBs) for this release on the Cisco ME 3400E Ethernet Access switch. It contains these sections:
•MIB List
•Using FTP to Access the MIB Files
MIB List
•BRIDGE-MIB (RFC1493)
Note The BRIDGE-MIB supports the context of a single VLAN. By default, SNMP messages using the configured community string always provide information for VLAN 1. To obtain the BRIDGE-MIB information for other VLANs, for example VLAN x, use this community string in the SNMP message: configured community string @x.
•CISCO-CABLE-DIAG-MIB
•CISCO-CDP-MIB
•CISCO-CONFIG-COPY-MIB
•CISCO-CONFIG-MAN-MIB
•CISCO-DHCP-SNOOPING-MIB
•CISCO-ENTITY-ALARM-MIB
•CISCO-ENTITY-FRU-CONTROL-MIB
•CISCO-ENTITY-SENSOR MIB
•CISCO-ENTITY-VENDORTYPE-OID-MIB
•CISCO-ENVMON-MIB
•CISCO-ERR-DISABLE-MIB
•CISCO-ETHER-CFM-MIB
•CISCO-ETHERNET-ACCESS-MIB
•CISCO-FLASH-MIB (Flash memory on all switches is modeled as removable flash memory.)
•CISCO-FTP-CLIENT-MIB
•CISCO-HSRP-MIB
Note Layer 3 MIBs are available only when the metro IP access image is running on the switch.
•CISCO-HSRP-EXT-MIB (partial support)
•CISCO-IGMP-FILTER-MIB
•CISCO-IMAGE-MIB
•CISCO-IPSLA-ETHERNET-MIB
Note Available only when the metro IP access image is running on the switch.
•CISCO-L2L3-INTERFACE-CONFIG-MIB
•CISCO-LAG-MIB
•CISCO-MAC-NOTIFICATION-MIB
•CISCO-MEMORY-POOL-MIB
•CISCO-NAC-NAD-MIB
•CISCO-PAE-MIB
•CISCO-PAGP-MIB
•CISCO-PING-MIB
•CISCO-PORT-QOS-MIB (the cportQosStats Table returns the values from the octets and packet counters, depending on switch configuration)
•CISCO-PRODUCTS-MIB
•CISCO-PROCESS-MIB
•CISCO-RTTMON-MIB
•CISCO-SMI-MIB
•CISCO-STACKMAKER-MIB
•CISCO-STP-EXTENSIONS-MIB
•CISCO-SYSLOG-MIB
•CISCO-TC-MIB
•CISCO-TCP-MIB
•CISCO-UDLDP-MIB
•CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
•CISCO-VLAN-MEMBERSHIP-MIB
•CISCO-VTP-MIB
•ENTITY-MIB
•ETHERLIKE-MIB
•IEEE8021-PAE-MIB
•IEEE8023-LAG-MIB
•IF-MIB (In and out counters for VLANs are not supported.)
•IGMP-MIB
•INET-ADDRESS-MIB
•IPMROUTE-MIB
•LLDP MIB
•OLD-CISCO-CHASSIS-MIB
•OLD-CISCO-FLASH-MIB
•OLD-CISCO-INTERFACES-MIB
•OLD-CISCO-IP-MIB
•OLD-CISCO-SYS-MIB
•OLD-CISCO-TCP-MIB
•OLD-CISCO-TS-MIB
•PIM-MIB
•RFC1213-MIB (Functionality is as per the agent capabilities specified in the CISCO-RFC1213-CAPABILITY.my.)
•RFC1253-MIB (OSPF-MIB)
•RMON-MIB
•RMON2-MIB
•SNMP-FRAMEWORK-MIB
•SNMP-MPD-MIB
•SNMP-NOTIFICATION-MIB
•SNMP-TARGET-MIB
•SNMPv2-MIB
•TCP-MIB
•UDP-MIB
Note For information about MIB support for a specific Cisco product and release, go to the MIB Locator tool at this URL:
http://tools.cisco.com/ITDIT/MIBS/MainServlet
Using FTP to Access the MIB Files
You can obtain each MIB file by using this procedure:
Step 1 Make sure that your FTP client is in passive mode.
Note Some FTP clients do not support passive mode.
Step 2 Use FTP to access the server ftp.cisco.com.
Step 3 Log in with the username anonymous.
Step 4 Enter your e-mail username when prompted for the password.
Step 5 At the ftp>
prompt, change directories to /pub/mibs/v1 and /pub/mibs/v2.
Step 6 Use the get MIB_filename command to obtain a copy of the MIB file.