Configuring Local CLI - Clish
Configuration Guidelines
You can configure the Cisco Edge 300 series switch in Clish, which is for the local CLI configuration. The CLI uses only commands that are specific to the Cisco Edge 300 series switch. Although the syntax is similar to the Cisco IOS CLI, the commands are incompatible with Cisco IOS commands.
Use the CLI to configure these switch settings:
- Basic switch settings—hostname, MAC address, Bluetooth settings, password, Network Time Protocol (NTP) server, and switch language
- Ethernet interface settings—status, speed, and quality of service (QoS)
- Wireless interface settings—status, radio, wireless mode, channel, wireless separation, transmission power, Wi-Fi Multimedia (WMM), and advanced wireless settings
- SSID security settings—broadcast, authentication, and encryption
Follow these configuration guidelines:
- Enter ssh root@ip-address in the Command Prompt in your PC, and enter the password after the welcome screen shows, then enter the command of clish to enter the Global Configuration Mode.
- Start a Cisco Edge configuration with the configure terminal global command. End the Cisco Edge configuration file with the exit global command.
- Within a Cisco Edge configuration, start each individual switch configuration with the system identifier local system configuration command. End each individual switch configuration with the done system configuration command.
Note please use system identifier local command for local CLI configuration.
- From the system configuration mode, you can enter these configuration modes:
– Ethernet configuration mode
Use the interface system configuration command to enter this mode. Use the exit global configuration command to return to the system configuration mode.
– WiFi interface configuration mode
Use the interface system configuration command to enter this mode. We recommend that before you configure any wireless settings, that you first use the wireless-mode WiFi configuration command to set the 802.11 wireless mode. Use the exit global configuration command to return to the system configuration mode.
– SSID configuration mode
Use the ssid system configuration command to enter this mode. Use the exit global configuration command to return to the system configuration mode.
- All commands must be entered in lowercase letters. Arguments can include uppercase letters.
- If there is a configuration conflict, the most recent configuration takes precedence. In this example, the SSID is not broadcast:
Relationship Between Local Configuration and Smart Install Configuration
Both local configuration and SMI(Smart Install) have a config file respectively on the Cisco Edge 300 series switch, and both local configuration and SMI(Smart Install) have scripts to excute config files on the Cisco Edge 300 series switch, and there is an execution flag decides which script is to run. By default, the flag is SMI.
If show running-configuration is configured on the Cisco Edge 300 series switch, it will show running configuration, and also show the source file that the running configuration is derived from. The next-reboot command specifies the config file to run next after the reboot. For example, if the next reboot local command is configured, the config file will be changed to local configuration.
In sunbird release 1.1 and earlier, the Cisco Edge 300 series switch will check the flag when the system reboots. If the flag points to local config file, then the system will change the flag back to SMI for the next reboot to make sure if the SMI works.
In sunbird release 1.2 and later, the Cisco Edge 300 series switch treats local configuration in two different ways based on the network status:
– If the Cisco Edge 300 series switch is connected to a SMI network and it is configured to apply SMI configuration, SMI config will always be applied instead of local configuration.
– If the Cisco Edge 300 series switch is connected to a non-smart install environment, it will supports remain local configuration in nand flash for every reboot if smi-environment is not setup for this particular box, you can do local configuration on it by the methods described in this chapter and then enter the following two commands to make sure that the Cisco Edge 300 series switch reboots from local configuration startup-config file next time, otherwise, all the configuration will be stored in RAM and will get lost after the reboot.
> copy running-config startup-config(local)
Switch Command Reference
NoteA syntax description, the command default mode, usage guidelines, and examples are provided A syntax description, the command default mode, usage guidelines, and examples are provided only for commands that are not self-explanatory.
Enable Mode
Table 4-1 Global Configuration Commands
|
|
configure terminal |
Starts the Cisco Edge configuration file, and enters global configuration mode. |
copy |
Copies any file from a source to a destination. |
exit |
Exits global configuration mode. |
next-reboot |
Selects next-reboot mode. |
reboot |
Halts and performs a cold restart. |
remove |
Removes local startup configuration |
show |
Show running system information |
configure terminal
To start the Cisco Edge configuration file and enter the global configuration mode, use the configure terminal in the global configuration mode.
configure terminal
Usage Guidelines
Each Cisco Edge configuration file must start with the configure terminal command.
copy
To copy any file from a source to a destination, use the copy command in the global configuratoin mode.
copy source-url destination-url
Syntax Description
source-url |
The location URL (or alias) of the source file or directory to be copied. The source can be either local or remote, depending upon whether the file is being downloaded or uploaded. |
destination-url |
The destination URL (or alias) of the copied file or directory. The destination can be either local or remote, depending upon whether the file is being downloaded or uploaded. |
Command Modes
Global configuration mode.
exit
To exit the configuration mode that you are in, use the exit command in any configuration mode.
exit
Command Modes
Global configuration
Switch configuration
Ethernet Interface configuration
WiFi Interface configuration
SSID configuration
Usage Guidelines
Use exit to leave a configuration mode and return to the previous configuration mode.
At the end of a Cisco Edge configuration file, use exit after the done system configuration command.
next-reboot
To select next-reboot mode, use the next-reboot command in the global configuratoin mode.
next-reboot
Command Modes
Global configuration mode.
reboot
To halt and perform a cold restart, use the reboot command in the global configuratoin mode.
reboot
Command Modes
Global configuration mode.
remove
To remove local startup configuration, use the remove command in the global configuratoin mode.
remove
Command Modes
Global configuration mode.
show
To display running system information, use the show command in the global configuratoin mode.
show
Command Modes
Global configuration mode.
System Configuration Mode
Table 4-2 System Configuration Commands
|
|
bluetooth |
Enables or disables Bluetooth on the switch. |
data-store |
Configures the system data storage location. |
desktop resolution |
Configures the desktop parameter. |
do |
Executes user EXEC or privileged EXEC commands from global configuration mode or other configuration modes or submodes. |
done |
Defines the end of an individual switch configuration and returns to the global configuration mode. |
exit |
Exits system configuration mode. |
hostname |
Configures the hostname of the switch. |
hosts |
Configures the ip address of the switch. |
interface |
Enters Ethernet interface configuration mode to configure a Fast Ethernet interface or the Gigabit Ethernet interface, or enters WiFi interface configuration mode to configure the wireless interface. |
language support |
Configures the language of the switch. |
locale |
Configures the time zone of the switch. |
login-window |
Enables or disables the login window. |
mac address-table aging-time |
Configures the period that a dynamic MAC address remains in the MAC address table after the address is used or updated. |
mac address-table static |
Adds a static MAC address to one or more interfaces and sets the default QoS mode. |
mgrvlan |
Configures the internal vlan used by the system |
no |
Removes the configuration for a command or sets the command to default. |
ntp server |
Configures the IP address of the NTP server that is used by the switch. |
password |
Sets the password. |
snmp-server |
Enables the Simple Network Management Protocol (SNMP) agent. |
snmp-server |
Configures the community access string to permit access to the Simple Network Management Protocol (SNMP)protocol. |
snmp-server contact |
Configures the system contact (sysContact) string. |
snmp-server group |
Configures a new Simple Network Management Protocol (SNMP) group, or a table that maps SNMP users to SNMP views. |
snmp-server location |
Configures the system location string. |
snmp-server user |
Configures a new user to an Simple Network Management Protocol (SNMP) group. |
snmp-server view |
Adds or updates a view entry. |
snmp-server |
Sets the SSID name, and enters SSID configuration mode to configure the security settings for the switch access point. |
system identifier local |
Enters system configuration mode to configure the locacl switch. |
vlan |
Adds a VLAN in system. |
wvlan |
Configure the wireless VLAN used by the WIFI AP. |
bluetooth
To enable or disable Bluetooth on the switch, use the bluetooth command in the system configuration mode.
bluetooth { on | off }
Command Default
Bluetooth is on.
data-store
To set the network file system (NFS) server location, use the data-store command in the system configuratoin mode.
data-store remote_ip_addr remote_path destination_path
Syntax Description
remote_ip_addr |
Configures the IP address of the NFS server. |
remote_path |
Configures the directory path. |
destination_path |
Configures the destination directory. |
Usage Guidelines
Do not mount the server to local system directories other than /mnt .
Examples
data-store 10.10.11.201 /var/ftp/upload /mnt
desktop resolution
To configure the resolution on the desktop, use the desktop resolution command in the system configuration mode.
desktop resolution { 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9}
Syntax Description
1 |
1280 x 960p85 |
2 |
720p |
3 |
1024 x 768p60 |
4 |
1080p |
5 |
720p50 |
6 |
1080p50 |
7 |
1080i |
8 |
1080i50 |
9 |
auto-resolution Note If user set a resolution that isn’t supported, it will be automatically switched to the auto-resolution mode. It’s recommended to connect the HDMI monitor before booting system to enable this new feature. |
help |
Sets desktop reslution, input 1-9 |
Command Default
1024x768p60
Usage Guidelines
Changing the desktop resolution requires a reboot.
do
To execute user EXEC or privileged EXEC commands from global configuration mode or other configuration modes or submodes, use the docommand in any configuration mode.
do command
Syntax Description
command |
The user EXEC or privileged EXEC command to be executed. |
Command Default
A user EXEC or privileged EXEC command is not executed from a configuration mode.
Command Modes
All configuration modes.
Usage Guidelines
Use this command to execute user EXEC or privileged EXEC commands (such as show, clear, and debug commands) while configuring your routing device. After the EXEC command is executed, the system will return to the configuration mode you were using.
done
To define the end of an individual switch configuration and return to the global configuration mode, use the done command in the system configuration mode.
done
Usage Guidelines
Each individual switch configuration must end with the done command.
hostname
To configure the hostname of the switch, use the hostname command in the system configuration mode.
hostname name
Syntax Description
name |
Name that you assign to the switch. |
Command Default
The default hostname is intel_ce_linux.
Usage Guidelines
Changing the hostname requires a reboot.
hosts
To configure the ip address of the switch, use the hosts command in the system configuration mode.
hosts ip-address
Syntax Description
ip-address |
Identifies the ip address for the switch. |
interface
To enter Ethernet interface configuration mode to configure a Fast Ethernet or the Gigabit Ethernet interface or to enter WiFi interface configuration mode to configure the wireless interface, use the interface command in the system configuration mode.
interface { fe1 | fe2 | fe3 | fe4 | gi1 | bvi1 }
Syntax Description
fe1 |
Configures the Fast Ethernet 1 interface. |
fe2 |
Configures the Fast Ethernet 2 interface. |
fe3 |
Configures the Fast Ethernet 3 interface. |
fe4 |
Configures the Fast Ethernet 4 interface. |
gi1 |
Configures the Gigabit Ethernet interface. |
bvi1 |
Configures the wireless interface. |
Usage Guidelines
Use the interface command to enter the Ethernet interface configuration mode or WiFi interface configuration mode.
Related Commands
Use the exit command to leave Ethernet interface configuration mode or WiFi interface configuration mode.
Table 4-3 lists the Ethernet interface configuration commands.
Table 4-4 lists the WiFi interface configuration commands.
language support
To configure the switch language, use the language support command in the system configuration mode.
language support { 1 |2 | 3 | 4 | 5| 6 | 7 | 8}
Syntax Description
1 |
English (US). |
2 |
Spanish (Europe). |
3 |
Spanish (Mexico). |
4 |
Simplified Chinese. |
5 |
Traditional Chinese (HK). |
6 |
Traditional Chinese (TW). |
7 |
Portuguese (PT). |
8 |
Portuguese (BR). |
Command Default
The default is English (US).
Usage Guidelines
Changing the language requires a reboot.
locale
To configure the time zone, use the locale command in the system configuration mode.
locale value
Syntax Description
|
|
0 |
GMT0 |
1 |
GMT+1 |
2 |
GMT+2 |
3 |
GMT+3 |
4 |
GMT+4 |
5 |
GMT+5 |
6 |
GMT+6 |
7 |
GMT+7 |
8 |
GMT+8 |
9 |
GMT+9 |
10 |
GMT+10 |
11 |
GMT+11 |
12 |
GMT+12 |
13 |
GMT-1 |
14 |
GMT-2 |
15 |
GMT-3 |
16 |
GMT-4 |
17 |
GMT-5 |
18 |
GMT-6 |
19 |
GMT-7 |
20 |
GMT-8 |
21 |
GMT-9 |
22 |
GMT-10 |
23 |
GMT-11 |
24 |
GMT-12 |
25 |
GMT+13 |
26 |
GMT+14 |
Command Default
The default time zone is GMT0.
login-window
To enable or disable the login window, use the login-window command in the system configuration mode.
login-window enable | disable
Syntax Description
enable |
Enables the login window. |
disable |
Disables the login window. |
Command Default
The login-window is enalbed by default.
mac address-table aging-time
To configure the period that a dynamic MAC address remains in the MAC address table after the address is used or updated, use the mac address-table aging-time command in the system configuration mode.
mac address-table aging-time aging-time
Syntax Description
aging-time |
The period in seconds after which a dynamic MAC address is no longer available in the MAC address table. The range is from 15 to 3825 seconds. |
Command Default
The default period is 330 seconds.
Usage Guidelines
When no packets arrive within the aging time period for a MAC address, it is removed from the MAC address table. If packets arrive for the MAC address after it has been removed from the table, the packets are forwarded to all interfaces except to the one on which they arrived. If the MAC address is received again, it is added to the table.
Configure 0 seconds to disable the timer and to prevent MAC addresses from being removed from the MAC address table.
mac address-table static
To add a static MAC address to one or more vlans and interfaces and set the default QoS mode, use the mac address-table static command in the system configuration mode.
mac address-table static mac-address vlan vlan id [ interface interface id] [ default | critical ]
Syntax Description
mac_address |
Identifies the switch by its MAC address in the xxxx.xxxx.xxxx format. |
vlan vlan-id |
Specifies the vlan for the static MAC address. |
interface interface id |
(Optional) Identifies the interface or interfaces to which the static MAC address is applied. These are the possible values for the interface id argument:
- fe1—Fast Ethernet interface 1
- fe2—Fast Ethernet interface 2
- fe3—Fast Ethernet interface 3
- fe4—Fast Ethernet interface 4
- gi1—Gigabit Ethernet interface
- cpu—CPU of the switch
|
default |
(Optional) Configures the interface for default QoS mode. |
critical |
(Optional) Configures the interface for critical QoS mode. |
Usage Guidelines
To prevent flooding, you can add a static MAC address to an interface. For example, you can configure a static MAC address for an attached uplink switch to prevent packet flooding to the Cisco Edge 300 series switch.
Configure critical QoS for an interface that receives relative important information in relation to the other interfaces. For example, to ensure high video quality, you can configure critical QoS for an interface that is connected to a surveillance camera.
Examples
This example shows how to assign the 1111.1111.1111 static MAC address to vlan 2 fe1 interfaces and sets the QoS mode to default:
mac address-table static 1111.1111.1111 vlan 2 interface fe1 default
mgrvlan
To configure the management VLAN of the switch, use the mgrvlan command in the system configuration mode.
mgrvlan vlan-id
Syntax Description
vlan-id |
The VLAN ID you assigned to the switch as the management VLAN. Range: 1 - 4094. |
Command Default
The default value for the vlan-id of mgrvlan is 1.
no
To remove the configuration for a command or set the command to default, use the no command in the system configuration mode.
no
Command Modes
System configuration
ntp server
To configure the IP address of the NTP server that is used by the switch, use the ntp server command in the system configuration mode.
ntp server ip address
Syntax Description
ip address |
The IP address of the NTP server. |
password
To set the root password and the student password, use password in the global configuration mode.
password
Command Modes
Global configuration mode.
snmp-server
To enable the Simple Network Management Protocol (SNMP) agent, use the snmp-server command in
the system configuration mode. To disable the service, use the no form of this command.
snmp-server
no snmp-server
Syntax Description
This command has no arguments or keywords.
snmp-server community
To configure the community access string to access the Simple Network Management Protocol (SNMP), use the snmp-server community in the system configuration command. To remove the specified community string, use the no form of this command.
snmp-server community string [view view-name] [ro | rw]
no snmp-server community string
Syntax Description
string |
Community string that acts like a password and permits access to the SNMP protocol. |
view |
Defines the objects available to the community. |
view-name |
Name of a previously defined view. |
ro |
Specifies read-only access. Authorized management stations are only able to retrieve MIB objects. |
rw |
Specifies read-write access. Authorized management stations are able to both retrieve and modify MIB objects. |
Command Default
By default, an SNMP community string permits read-only access to all objects.
snmp-server contact
To configure the system contact (sysContact) string, use the snmp-server contact in the system configuration mode. To remove the system contact information, Use the no form of this command.
snmp-server contact text
no snmp-server contact
Syntax Description
text |
String that describes the system contact information. |
Command Default
No system contact string is set.
snmp-server group
To configure a new Simple Network Management Protocol (SNMP) group, or configure a table that maps SNMP users to SNMP views, use the snmp-server group in the system configuration mode. To remove a specified SNMP group, use the no form of this command.
snmp-server group groupname {v1 | v2c | v3 {auth | noauth | priv}} [read readview] [write writeview]
no snmp-server group
Syntax Description
groupname |
The name of the group. |
v1 |
Specifies the least secure of the possible security models. |
v2c |
Specifies the second least secure of the possible security models. It allows for the transmission of informs and counter 64, which allows for integers twice the width of what is normally allowed. |
v3 |
Specifies the most secure of the possible security models. |
auth |
Specifies authentication of a packet without encrypting it. |
noauth |
Specifies no authentication of a packet. |
priv |
Specifies authentication of a packet with encryption. |
read |
Specifies a read view. |
readview |
Name of the view that enables you only to view the contents of the agent. Range: 0 to 64 characters. |
write |
Specifies a write view. |
writeview |
Name of the view that enables you to enter data and configure the contents of the agent. Range: 0 to 64 characters. |
snmp-server location
To configure the SNMP server system location string, use the snmp-server location in the system configuration mode. To remove the location string, use the no form of this command .
snmp-server location text
no snmp-server location
Syntax Description
text |
String that describes the system location information. |
Defaults
No system location string is set.
snmp-server user
To configure a new user to an Simple Network Management Protocol (SNMP) group, use the snmp-server user in the system configuration mode. To remove a user from an SNMP group, use the no form of the command.
snmp-server user username groupname {v1 | v2c | v3} auth {md5 | sha} auth-password [priv {des | aes} password]
no snmp-server user
Syntax Description
username |
The name of the user connected to the agent on the host. |
groupname |
The name of the group associated to the user. |
v1 |
The least secure of the possible security models. |
v2c |
The second least secure of the possible security models. It allows the transmission of informs and counter 64, which is twice what is normally allowed. |
v3 |
The most secure of the possible security models. |
auth |
Initiates an authentication level setting session. |
md5 |
The MD5 authentication level. |
sha |
The SHA authentication level. |
auth-password |
A string that enables the agent to receive packets from the host. Range: 8 to 64 characters. |
priv |
Initiates a privacy authentication level setting session. |
des |
Use DES algorithm for encryption. |
aes |
Use AES algorithm for encryption. |
priv password |
A string that enables the host to encrypt the contents of the message it sends to the agent. Range: 8 to 64 characters. |
snmp-server view
To add or update a view entry, use the snmp-server view global configuration command. To remove the specified Simple Network Management Protocol server view entry, use the no form of this command.
snmp-server view view-name oid-tree {included | excluded}
no snmp-server view view-name
Syntax Description
view-name |
Label for the view record that you are updating or creating. The name is used to reference the record. |
oid-tree |
Object identifier of the ASN.1 subtree to be included or excluded from the view. To identify the subtree, specify a text string consisting of numbers, such as 1.3.6.2.4. |
included |
Specifies the view as included. |
excluded |
Specifies the view as excluded. |
Command Default
No view entry exists.
ssid
To set the SSID name and enter SSID configuration mode to configure the security settings for the access point of the switch, use the ssid command in the system configuration mode.
ssid ssid
Syntax Description
ssid |
SSID name for the access point. The name can consist of up to 32 characters. |
Command Default
The default SSID name is CISCO_EDGE.
Related Commands
Use the exit command to leave SSID configuration mode.
Table 4-5 lists the SSID configuration commands.
system identifier local
To set all switches to their default setting or to enter the system configuration mode to configure an individual switch, use the system identifier local in the global configuration mode
system identifier local
Command Modes
Global configuration mode.
vlan
To add a VLAN in system, use the vlan command in the system configuration mode.
vlan vlan-id
Syntax Description
vlan-id |
VLAN ID assigned to the port. Range: 1-4094. Concurrent number should be less than 6. |
Command Default
The default value for all ports is access mode vlan 1.
wvlan
To configure the wireless VLAN of the switch, use the wvlan command in the system configuration mode.
wvlan vlan-id
Syntax Description
vlan-id |
Wireless VLAN ID assigned to the switch. |
Command Default
The default value for vlan-id of wvaln is 1.
Ethernet Interface Configuration Mode
Table 4-3 Ethernet Interface Configuration Commands
|
|
disable |
Disables an interface. |
duplex |
Configures the duplex mode for an interface. |
enable |
Enables an interface. |
exit |
Exits Ethernet interface configuration mode. |
output-queue-strategy |
Configures the type of output traffic scheduling on an interface. |
priority |
Configures the QoS priority for incoming traffic on an interface. |
rate-limit |
Configures rate-limiting for broadcast and unknown unicast traffic on an interface. |
speed |
Configures the speed for an interface. |
switchport mode |
Configures the switchport mode of the switch |
disable
To disable an interface, use the disable command in the Ethernet interface configuration mode.
disable { fe1 | fe2 | fe3 | fe4 | gi1 }
Syntax Description
fe1 |
Disables the Fast Ethernet 1 interface. |
fe2 |
Disables the Fast Ethernet 2 interface. |
fe3 |
Disables the Fast Ethernet 3 interface. |
fe4 |
Disables the Fast Ethernet 4 interface. |
gi1 |
Disables the Gigabit Ethernet interface. |
Defaults
All interfaces are enabled.
Related Commands
The enable command enables an interface.
duplex
To configure the duplex mode for an interface, use the duplex command in the Ethernet configuration mode.
duplex {auto | half | full }
Syntax Description
auto |
Configures automatic duplex mode sensing. |
half |
Configures half-duplex mode. |
full |
Configures full-duplex mode. |
Defaults
The defaults is automatic duplex mode sensing.
enable
To disable an interface, use the enable command in Ethernet interface configuration mode or WiFi interface configuration mode.
enable { fe1 | fe2 | fe3 | fe4 | bvi1 }
Syntax Description
fe1 |
Enables the Fast Ethernet interface 1. |
fe2 |
Enables the Fast Ethernet interface 2. |
fe3 |
Enables the Fast Ethernet interface 3. |
fe4 |
Enables the Fast Ethernet interface 4. |
bvi1 |
Enables the wireless interface 1. |
Defaults
All interfaces are enabled.
Related Commands
The disable command disables an interface.
output-queue-strategy
To configure the type of output traffic scheduling on an interface, use the output-queue-strategy command in the Ethernet configuration mode.
output-queue-strategy { strict | wrr }
Syntax Description
strict |
Configures traffic scheduling based on the queue priority. |
wrr |
Configures traffic scheduling based on weighted round robin (WRR). |
Defaults
The default traffic scheduling is wrr .
priority
To configure the QoS priority for incoming traffic on an interface, use the priority command in the Ethernet interface configuration mode.
priority { high | normal }
Syntax Description
high |
Configures incoming traffic as high priority. |
normal |
Configures incoming traffic as normal priority. |
Defaults
Incoming traffic is treated as normal priority.
rate-limit
To configure rate-limiting for broadcast and unknown unicast traffic on an interface, use the rate-limit command in the Ethernet interface configuration mode.
rate-limit { none | set broadcast | set unknown-unicast | set both } rate
Syntax Description
none |
Disables rate-limiting. |
set broadcast |
Configures rate-limiting for broadcast traffic. |
set unknown-unicast |
Configures rate-limiting for unknown unicast traffic. |
set both |
Configures rate-limiting for both broadcast traffic and unknown unicast traffic. |
rate |
A value between 1 MB and 100 MB. |
Defaults
Rate-limiting is disabled.
speed
To configure the speed for an interface, use the speed command in the Ethernet configuration mode.
speed { auto | 10 | 100 | 1000 }
Syntax Description
auto |
Configures automatic speed sensing. |
10 |
Configures 10 Mb/s speed. |
100 |
Configures 100 Mb/s speed. |
1000 |
Configures 1000 Mb/s speed and full-duplex mode. Note 1000 Mb/s speed is supported only on the Gi1 interface. |
Defaults
The defaults are automatic speed sensing.
switchport mode
To configure the switchport mode of the switch, use the switchport mode command in the Ethernet configuration mode.
switchport mode trunk | access vlan vlan-id
Syntax Description
trunk |
Sets the switch port mode to trunkmode with a specific VLAN. After you configured switchport mode trunk, there are three commands can be configured under the switchport mode trunk mode as the following:
- native vlan_id—sets native VLAN ID.
- add vlan_id—add a VLAN ID to the trunk port
- remove vlan_id—remove VLAN ID from the trunk port VLAN list
|
access |
Sets the switch port to access mode with a specific VLAN. |
Command Default
The default mode for switchport is access.
WiFi Interface Configuration Mode
Table 4-4 WiFi Interface Configuration Commands
|
|
ap-isolation |
Configures wireless separation for clients that are connected to the same SSID. |
apsd |
Configures Wi-Fi Multimedia (WMM) power save mode for the access point. |
beacon-interval |
Configures the beacon interval for the access point. |
bg-protection |
Configures the CTS-to-self protection for the access point. |
channel bandwidth |
Configures the channel width when the access point functions in 802.11n mode or 802.11n mixed mode. |
channel number |
Configures the channel number (which sets the frequency) for the access point. |
data-beacon-rate |
Configures the Delivery Traffic Indication Message (DTIM) interval for the access point. |
enable |
Enables the interface. |
exit |
Exits WiFi interface configuration mode. |
extension channel |
Configures the control side band that is used for the extension or secondary channel when the access point functions in 802.11n mode or 802.11n mixed mode. |
guard-interval |
Configures the period between packets when the access point functions in 802.11n mode or 802.11n mixed mode. |
igmp-snoop |
Enables or disables Internet Group Management Protocol (IGMP) snooping. |
mcs |
Configures the high throughput Modulation and Coding Schemes (MCS) rate when the access point functions in 802.11n mode or 802.11n mixed mode. |
multicast-mcs |
Configures the high throughput Modulation and Coding Schemes (MCS) rate on multicast frames. |
multicast-phy-mode |
Configures PHY mode on multicast frames. |
operating-mode |
Configures greenfield or mixed mode when the access point functions in 802.11n mode. |
packet aggregation |
Configures Aggregate MAC Service Data Unit (A-MSDU) packet aggregation when the access point functions in 802.11n mode or 802.11n mixed mode. |
radio |
Turns the access point wireless radio on or off. |
rdg |
Configures the Reverse Direction Grant (RDG) when the access point functions in 802.11n mode or 802.11n mixed mode. |
short-slot |
Configures the short-slot time when the access point functions in 802.11g mode or 802.11g mixed mode. |
transmit burst |
Configures the transmit burst (Tx burst) for the access point. |
transmit preamble |
Configures the preamble for the access point. |
transmit power |
Configures the power at which the access point radio transmits its wireless signal. |
wireless-mode |
Configures the 802.11 wireless mode for the access point. |
wmm |
Configures Wi-Fi Multimedia (WMM) for the access point. |
ap-isolation
To configure wireless separation for clients that are connected to the same SSID, use the ap-isolation command in the WiFi interface configuration mode.
ap-isolation { on | off }
Syntax Description
on |
Enables wireless separation. This prevents wireless clients that are connected to the same SSID from communicating with each other. |
off |
Disables wireless separation. This allows wireless clients that are connected to the same SSID to communicate with each other. |
Related Commands
WiFi interface configuration
apsd
To configure Wi-Fi Multimedia (WMM) power save mode for the access point, use the apsd command in the WiFi interface configuration mode.
apsd { on | off }
Syntax Description
on |
Enables WMM power save mode. |
off |
Disables WMM power save mode. |
Command Default
WMM power save mode is disabled.
Usage Guidelines
You can configure the apsd command only when the Wi-Fi Multimedia (WMM) is enabled.
Related Commands
Use the wmm command to enable WMM.
beacon-interval
To configure the beacon interval for the access point, use the beacon-interval command in the WiFi interface configuration mode.
beacon-interval interval
Syntax Description
interval |
A period between 20 and 1000 milliseconds. |
Command Default
The default period is 100 milliseconds.
Usage Guidelines
The default setting should work well for most networks.
Configure a long interval to
- Increase the access point throughput performance.
- Decrease the discovery time for clients and decrease the roaming efficiency.
- Decrease the power consumption of the clients.
Configure a short interval to
- Minimize the discovery time for clients and improve the roaming efficiency
- Decrease the access point throughput performance.
- Increase the power consumption of the clients.
bg-protection
NoteThis command applies to 802.11b/g mixed mode, 802.11n/g mixed mode, and 802.11b/g/n mixed mode. This command applies to 802.11b/g mixed mode, 802.11n/g mixed mode, and 802.11b/g/n mixed mode.
To configure the CTS-to-self protection for the access point, use the bg-protection command in the WiFi interface configuration mode.
bg-protection { auto | on | off }
Syntax Description
auto |
Configures automatic selection of CTS-to-self protection. |
on |
Enables CTS-to-self protection. |
off |
Disables CTS-to-self protection. |
Command Default
The default is automatic selection of CTS-to-self protection.
Usage Guidelines
CTS-to-self protection minimizes collisions among clients in a mixed mode environment but reduces throughput performance.
channel bandwidth
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure the channel width when the access point functions in 802.11n mode, use the channel bandwidth command in the WiFi interface configuration mode.
channel bandwidth { 20 | 20/40 }
Syntax Description
20 |
Configures a 20-MHz channel width. |
20/40 |
Configures automatic selection of 20-MHz or 40-MHz channel width. |
Command Default
The default is automatic selection of 20-MHz or 40-MHz channel width.
Usage Guidelines
The default setting should work well for most networks.
A 40-MHz channel provides a higher throughput performance for 802.11n clients.
802.11b and 802.11g clients can function only with a 20-MHz channel.
Related Commands
The setting of the channel bandwidth command affects the options for the mcs command.
channel number
To configure the channel number (which sets the frequency) for the access point, use the channel number command in the WiFi interface configuration mode.
channel number { auto | number }
Syntax Description
auto |
Configures automatic selection of the channel number. |
number |
A value between 1 and 14, or 0 (automatic selection). |
Command Default
The default channel number is 6.
Usage Guidelines
We recommend that you either use the default channel number or the automatic selection of the channel number and only change the channel number if you experience interference in the network.
If you need to change the channel number, use the following numbers based on your location:
- China and Europe: 1 to 13
- America: 1 to 11
- Japan: 14 (for 11b only)
data-beacon-rate
To configure the Delivery Traffic Indication Message (DTIM) interval for the access point, use the data-beacon-rate command in the WiFi interface configuration .
data-beacon-rate rate
Syntax Description
rate |
A value between 1 and 255 milliseconds. |
Command Default
The default rate is 1 millisecond.
Usage Guidelines
The DTIM interval is a multiple of the beacon interval. Before you change the DTIM interval, consider the types of clients in the network: laptops might function better with a short interval, but mobile phones might function better with a long interval.
A long interval allows clients to save power but can delay multicast and broadcast traffic.
A short interval decreases delivery time of multicast and broadcast traffic but can increase power consumption by clients.
Related Commands
The setting of the beacon-interval command affects the data-beacon-rate command.
extension channel
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure the control sideband that is used for the extension or secondary channel when the access point functions in 802.11n mode, use the extension channel command in the WiFi interface configuration mode.
extension channel { upper | lower }
Syntax Description
upper |
Configures the upper extension channel. |
lower |
Configures the lower extension channel. |
Command Default
The lower extension channel is configured.
Usage Guidelines
This command has effect only when you configure a 40-MHz channel width.
When the main channel number is in the lower range (for example, in the 1–4 range), use the upper extension channel.
When the main channel number is in the upper range (for example, in the 10–13 range), use the lower extension channel.
When the main channel number is in the middle range (for example, in the 5–9 range), use either the upper or lower extension channel.
guard-interval
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure the period between packets when the access point functions in 802.11n mode, use the guard-interval command in the WiFi interface configuration mode.
guard-interval { 400 | 800 }
Syntax Description
400 |
Configures a short guard interval of 400 nanoseconds. |
800 |
Configures a long guard interval of 800 nanoseconds. |
Command Default
The default is 400 nanoseconds (ns).
Usage Guidelines
Use a 400-ns interval to increase the throughput performance for 802.11n clients but risk some packet errors and multipath interference.
Use an 800-ns interval to minimize packet errors and multipath interference but decrease the throughput performance for 802.11n clients.
Related Commands
The setting of the guard-interval command affects the options for the mcs command.
igmp-snoop
To enable or disable IGMP snooping on the wireless interface, use the igmp-snoop command in the WiFi interface configuration mode.
igmp-snoop { on | off }
Command Default
IGMP snooping is off.
mcs
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure the high throughput Modulation and Coding Schemes (MCS) rate when the access point functions in 802.11n mode, use the mcs command in the WiFi interface configuration mode.
mcs index_number
Syntax Description
index_number |
A value between 0 and 15, or 33 (automatic selection). |
Command Default
The default is 33 (automatic rate configuration).
Usage Guidelines
This table shows the MCS index numbers with their potential data rates in Mb/s based on MCS, guard interval, and channel width.
|
|
|
|
|
|
|
0 |
6.5 |
13.5 |
7 2/9 |
15 |
1 |
13 |
27 |
14 4/9 |
30 |
2 |
19.5 |
40.5 |
21 2/3 |
45 |
3 |
26 |
54 |
28 8/9 |
60 |
4 |
39 |
81 |
43 1/3 |
90 |
5 |
52 |
109 |
57 5/9 |
120 |
6 |
58.5 |
121.5 |
65 |
135 |
11 |
52 |
108 |
57 7/9 |
120 |
12 |
78 |
162 |
86 2/3 |
180 |
13 |
104 |
216 |
115 5/9 |
240 |
14 |
117 |
243 |
130 |
270 |
15 |
130 |
270 |
144 4/9 |
300 |
33 |
Configures automatic selection of the MCS index number. |
We recommend that you use automatic selection of the MCS index number. Change the MCS index to a fixed number only if the Received Signal Strength Indication (RSSI) for the clients in the network can support the selected MCS index number.
Related Commands
The setting of the channel bandwidth command affects the options for the mcs command.
The setting of the guard-interval command affects the options for the mcs command.
multicast-mcs
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure the high throughput Modulation and Coding Schemes (MCS) rate on multicast frames when the access point functions in 802.11n mode, use the multicast-mcs command in the WiFi interface configuration mode.
multicast-mcs index_number
Syntax Description
index_number |
A value between 0 and 15. |
Command Default
The default is 2.
Usage Guidelines
This table shows the MCS index numbers with their potential data rates in Mb/s based on MCS, guard interval, and channel width.
|
|
|
|
|
|
|
0 |
6.5 |
13.5 |
7 2/9 |
15 |
1 |
13 |
27 |
14 4/9 |
30 |
2 |
19.5 |
40.5 |
21 2/3 |
45 |
3 |
26 |
54 |
28 8/9 |
60 |
4 |
39 |
81 |
43 1/3 |
90 |
5 |
52 |
109 |
57 5/9 |
120 |
6 |
58.5 |
121.5 |
65 |
135 |
7 |
65 |
135 |
72 2/9 |
152.5 |
8 |
13 |
27 |
14 4/9 |
30 |
9 |
26 |
54 |
28 8/9 |
60 |
10 |
39 |
81 |
43 1/3 |
90 |
11 |
52 |
108 |
57 7/9 |
120 |
12 |
78 |
162 |
86 2/3 |
180 |
13 |
104 |
216 |
115 5/9 |
240 |
14 |
117 |
243 |
130 |
270 |
15 |
130 |
270 |
144 4/9 |
300 |
multicast-phy-mode
To configure PHY mode on multicast frames when the access point functions in 802.11n mode, use the multicast-phy-mode command in the WiFi interface configuration mode.
multicast-phy-mode { 0 | 1 | 2 | 3 }
Syntax Description
0 |
Disabled |
1 |
CCK (802.11b) |
2 |
OFDM (802.11g) |
3 |
HTMIX (802.11b/g/n) |
Command Default
The default is 2.
operating-mode
NoteThis command applies to 802.11n mode. This command applies to 802.11n mode.
To configure greenfield or mixed mode when the access point functions in 802.11n mode, use the operating-mode command in the WiFi interface configuration mode.
operating-mode { greenfield | mixed }
Syntax Description
greenfield |
Configures greenfield mode, which improves 802.11n throughput performance but prevents 802.11b and 802.11g clients in the coverage area from recognizing the 802.11n traffic. |
mixed |
Configures mixed mode, which allows the 802.11b and 802.11g clients in the coverage area to recognize the 802.11n traffic. |
Command Default
The default is mixed mode.
Usage Guidelines
Use greenfield mode if there are only 802.11n clients in the coverage area. If you use greenfield mode when 802.11b, 802.11g, and 802.11n clients coexist in the same coverage area, packet collisions might occur.
Use mixed mode when 802.11b, 802.11g, and 802.11n clients coexist in the same coverage area.
packet aggregation
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure Aggregate MAC Service Data Unit (A-MSDU) packet aggregation when the access point functions in 802.11n mode, use the packet aggregation command in the WiFi interface configuration mode.
packet aggregation { on | off }
Syntax Description
on |
Enables packet aggregation. |
off |
Disables packet aggregation. |
Command Default
Packet aggregation is off.
Usage Guidelines
Enable packet aggregration if network traffic consists primarily of data.
Disable packet aggregration if network traffic consists primarily of voice, video, or other multimedia traffic.
radio
To turn the access point wireless radio on or off, use the radio command in the WiFi interface configuration mode.
radio { on | off }
Syntax Description
on |
Enables the wireless radio. |
off |
Disables the wireless radio. |
Command Default
The wireless radio is disabled.
Usage Guidelines
If you do not intend to use the access point, turn off the radio.
rdg
NoteThis command applies to 802.11n mode or 802.11n mixed mode. This command applies to 802.11n mode or 802.11n mixed mode.
To configure the Reverse Direction Grant (RDG) when the access point functions in 802.11n mode, use the rdg command in the WiFi interface configuration mode.
rdg { on | off }
Syntax Description
on |
Enables RDG. |
off |
Disables RDG. |
Command Default
RDG is disabled.
Usage Guidelines
When RDG is enabled, a transmitter that has reserved the channel transmission opportunity allows the receiver to send packets in the reserved direction. When RDG is disabled, packets can be transmitted only in one direction during the channel transmission opportunity reservation.
Enable RDG for better throughput performance for 802.11n traffic.
short-slot
NoteThis command applies to 802.11g mode or 802.11g mixed mode. This command applies to 802.11g mode or 802.11g mixed mode.
To configure the short-slot time when the access point functions in 802.11g mode or 802.11g mixed mode, use the short-slot command in the WiFi interface configuration mode.
short-slot { on | off }
Syntax Description
on |
Enables short-slot time. |
off |
Disables short-slot time. |
Command Default
Short-slot time is enabled.
Usage Guidelines
Enable the short-slot time for better throughput performance for 802.11g clients.
If there are mostly 802.11b clients in the network, disable the short-slot time.
transmit burst
To configure the transmit burst (Tx burst) for the access point, use the transmit burst command in the WiFi interface configuration mode.
transmit burst { on | off }
Syntax Description
on |
Enables Tx burst. |
off |
Disables Tx burst. |
Command Default
Tx burst is enabled.
Usage Guidelines
Leave Tx burst on for better throughput performance.
Disable Tx burst if you notice wireless interference in the network.
transmit preamble
To configure the preamble for the access point, use the transmit preamble command in the WiFi interface configuration mode.
transmit preamble { long | short | auto }
Syntax Description
long |
Configures a long preamble. |
short |
Configures a short preamble. |
auto |
Configures automatic preamble selection. |
Command Default
The default is a long preamble.
Usage Guidelines
Use the long preamble setting for compatibility with legacy 802.11 systems operating at 1 and 2 Mb/s.
Configure a short preamble setting to improve throughput performance.
transmit power
To configure the power at which the access point radio transmits its wireless signal, use the transmit power command in the WiFi interface configuration mode.
transmit power percentage
Syntax Description
percentage |
A value between 1 and 100. |
Command Default
The default is 100 percent.
Usage Guidelines
For transmission of the wireless signal over a long distance, use the 100 percent setting.
For transmission of the wireless signal over a short distance, for example, when all clients are in a small room, lower the percentage.
wireless-mode
To configure the 802.11 wireless mode for the access point, use the wireless-mode command in the WiFi interface configuration mode.
wireless-mode { 0 | 1 | 4 | 6 | 7 | 9 }
Syntax Description
0 |
Configures 802.11b/g mixed mode. |
1 |
Configures 802.11b mode. |
4 |
Configures 802.11g mode. |
6 |
Configures 802.11n mode. |
7 |
Configures 802.11n/g mixed mode. |
9 |
Configures 802.11b/g/n mixed mode. |
Command Default
The default is 802.11b/g/n mixed mode.
Usage Guidelines
802.11b/g mixed mode—Select this mode if you have devices in the network that support 802.11b and 802.11g.
802.11b mode—Select this mode if all devices in the wireless network only support 802.11b.
802.11g mode—Select this mode if all devices in the wireless network only support 802.11g.
802.11n mode—Select this mode if all devices in the wireless network only support 802.11n.
802.11b/g/n mixed mode—Select this mode if you have devices in the network that support 802.11b, 802.11g, and 802.11n.
wmm
To configure Wi-Fi Multimedia (WMM) for the access point, use the wmm command in the WiFi interface configuration mode.
wmm { on | off }
Syntax Description
on |
Enables WMM. |
off |
Disables WMM. |
Command Default
WMM is disabled.
Usage Guidelines
WMM provides QoS for wireless traffic. If there is a lot of mixed media traffic (voice, video, data), enable WMM.
Related Commands
Use the apsd command to configure WMM power save mode.
SSID Configuration Mode
To enter SSID mode, perform the following steps:
NoteConfiguration for SSID will take effect after exiting the SSID configuring mode. Configuration for SSID will take effect after exiting the SSID configuring mode.
broadcast ssid
To enable or disable broadcast of the SSID name, use the broadcast ssi d command in the SSID configuration mode.
broadcast ssid { on | off }
Syntax Description
on |
Enables broadcast of the SSID name. |
off |
Disables broadcast of the SSID name. |
Command Default
The SSID is broadcast.
Usage Guidelines
Disable broadcast of the SSID for enhanced security. Only wireless clients who know the SSID can connect to the access point.
Enable broadcast of the SSID for wider availability and easier access.
encryption mode (open, shared, or WEP configuration)
To configure open, shared, or Wired Equivalency Privacy (WEP) authentication and associated encryption for the access point, use the encryption mode command in the SSID configuration mode.
encryption mode { open | shared } type { none | wep { key { 1 | 2 | 3 | 4 } { hex number | ascii phrase }}}
Syntax Description
open |
Configures open access without authentication. |
shared |
Configures authentication with a shared key. |
none |
Configures no encryption. |
wep |
Configures WEP encryption. |
key 1 key 2 key 3 key 4 |
Configures the key number for WEP encryption. (You can use only one of the four keys.) |
hex number |
Configures either authentication with a hexadecimal key or authentication and encryption with a hexadecimal key:
- When you select the none keyword, configures authentication with a hexadecimal key.
- When you select the wep keyword, configures authentication and encryption with a hexadecimal key.
For number , enter either 10 or 26 hexadecimal digits. |
ascii phrase |
Configures either authentication with a passphrase or authentication and encryption with a passphrase:
- When you select the none keyword, configures authentication with a passphrase.
- When you select the wep keyword, configures authentication and encryption with a passphrase.
For phrase , enter either 5 or 13 alphanumerical characters. Dash (-) and underscore (_) characters are supported. |
Command Default
The default is open access and no encryption.
Usage Guidelines
For shared access without encryption, the WEP hexadecimal number or passphrase is used only for authentication.
For shared access with WEP encryption, the WEP hexadecimal number or passphrase is used for both authentication and encryption.
Examples
This example shows how to configure shared authentication and WEP encryption, using key 3 and a passphrase of 3uifsfis-_0r5:
encryption mode shared type wep key 3 ascii 3uifsfis-_0r5
encryption mode (WPA configuration)
To configure Wi-Fi Protected Access (WPA) authentication and associated encryption for the access point, use the encryption mode command in the SSID configuration mode.
encryption mode { wpapsk | wpa2psk | wpapskwpa2psk } type { tkip | aes | tkipaes }
pass-phrase phrase
Syntax Description
wpapsk |
Configures WPA with preshared key (PSK) authentication. |
wpa2psk |
Configures WPA2 with PSK authentication. |
wpapskwpa2psk |
Configures combined WPA and WPA2 with PSK authentication. |
tkip |
Configures Temporal Key Integrity Protocol (TKIP) encryption. |
aes |
Configures Advanced Encryption Standard (AES) encryption. |
tkipaes |
Configures combined TKIP and AES encryption. |
pass-phrase phrase |
Configures a passphrase (password). For phrase , enter at least 8 and at most 63 alphanumerical characters. Dash (-) and underscore(_) characters are supported. |
Command Default
The default is open access and no encryption.
Examples
This example shows how to configure combined WPA and WPA2 authentication with combined TKIP and AES encryption, using a passphrase of safE478_Ty33Yep-:
encryption mode wpapskwpa2psk type tkipaes pass-phrase safE478_Ty33Yep-
encryption mode (802.1x)
To configure Wi-Fi Protected Access (WPA) authentication and associated encryption for the access point, use the encryption mode command in the SSID configuration mode.
NoteThe encryption mode (802.1x) should be used in combination of radius-server. The encryption mode (802.1x) should be used in combination of radius-server.
encryption mode { wpa | wpa2 | wpa1wpa2 } type { tkip | aes | tkipaes }
Syntax Description
wpa |
Configures WPA with 802.1x authentication. |
wpa2 |
Configures WPA2 with 802.1x authentication. |
wpa1wpa2 |
Configures combined WPA and WPA2 with 802.1x authentication. |
tkip |
Configures Temporal Key Integrity Protocol (TKIP) encryption. |
aes |
Configures Advanced Encryption Standard (AES) encryption. |
tkipaes |
Configures combined TKIP and AES encryption. |
Command Default
The default mode is wpa2psk access, tkipaes encryption and the password is Cisco123.
Examples
This example shows how to configure combined WPA and WPA2 authentication with combined TKIP and AES
encryption, using 802.1x authentication method:
encryption mode wpa1wpa2 type tkipaes
radius-server
To configure the related information of a radius-server, use the radius-server in the SSID configuration mode.
radius-server host hostname [auth-port port_number] [key secret]
Syntax Description
hostname |
The IP address of the radius server. |
auth-port |
Specifies the authentication port number of the radius server. |
port_number |
The authentication port number of the radius server. |
key |
Specifies the password of the authentication service on the radius server. |
secret |
The password of the authentication service on radius server. |
Command Default
The default value for port_number is 1812.
The default value for secret is NULL.
Examples
This example shows how to configure the related information of a radius-server:
radius-server host 192.168.1.1 auth-port 1812 key pass1234
Show Commands
You can use the following show commands in the global configuratoin mode to display the configuration on the Cisco Edge 300 series switch:
- show 3rd-party-software-version: Displays the third party software version.
- show bluetooth: Displays the bluetooth status.
- show channel: Displays the AP wireless channel setting.
- show cisco-software-version: Displays the Cisco software version.
- show cpu: Show CPU.
- show desktop-resolution: Displays the desktop resolution information.
- show dhcp: Displays the DHCP information.
- show disk: Displays the disk usage.
- show dns: Displays the DNS information.
- show factory-mode-os-version: Displays the Factoy-Mode OS version.
- show hostname: Displays the hostname.
- show interfaces: Displays the Interface status and configuration.
- show ip: Displays the IP information.
- show mac: Displays the MAC table information.
- show memory: Displays the memory usage.
- show nfs: Displays NFS mount status.
- show os-version: Displays the Normal-Mode OS version.
- show port-statistics: Displays the switch port statistics.
- show port-status: Displays the switch port status.
- show qos: Displays the current QoS configuration.
- show running-config: Displays the current operating configuration.
- show snmp: Displays the status of SNMP communications.
- show snmp group: Displays the names of groups on the router, the security model, the status of the different views, and the storage type of each group.
- show snmp user: Displays the information on each Simple Network Management Protocol (SNMP) username in the group username table.
- show snmp view: Displays the family name, storage type, status of a Simple Network Management Protocol (SNMP) configuration and associated MIB.
- show ssid: Displays the AP wireless ssid setting.
- show startup-config: Displays the contents of startup configuration.
- show USB: Displays the USB device information.
- show vlan: Displays the vlan configuration.
- show vstack config: Displays the Smart Install VLAN configuration.
- show wireless-clients: Displays the AP wireless wireless-clients associated.
- show wireless-clients-number: Displays the associated wireless clients number.
- show wireless-mode: Displays the AP wireless wireless-mode setting.