Loop detection guard can be configured only on Layer 2 physical interfaces. Layer 3 ports and virtual interfaces, such as
port channels, switch virtual interfaces (SVIs), and tunnels, are not supported.
Information About Loop Detection Guard
A computer network can experience a network loop where there is more than one Layer 2 path between two endpoints. This is
possible when there are multiple connections between two switches in a network or two ports on the same switch are connected
to each other. The following figure shows a few examples of a network loop:
Example 1: Switch SW A, which is within the network, is sending traffic to an unmanaged switch on one port and receiving traffic
from the same unmanaged switch, on another port. On the unmanaged switch, the port receiving traffic is connected to the port
sending traffic back to the SW A in the network, resulting in a network loop.
Example 2: This example shows a network loop involving four switches, two within the network (SW A and SW B) and two unmanaged
switches (Un A and Un B). Traffic is moving in the following direction SW A to SW B to Un A to Un B and back to SW A, resulting
in a network loop.
Example 3: Two ports on the unmanaged switch are connected to each other, resulting in a network loop.
While Spanning Tree Protocol (STP) is normally the protocol that is configured for this purpose (to prevent network loops),
loop detection guard is suited to situations where there may be unmanaged switches in a network that do not understand STP,
or where STP is not configured on the network.
Loop detection guard is enabled at the interface level. To detect loops, the system sends loop-detect frames from the interface,
at preconfigured intervals. When a loop is detected, the configured action is taken.
Loop detection guard is disabled by default. When you enable the feature, you can configure one of these actions:
Error-disable the port sending traffic.
Error-disable the port receiving traffic (default).
Display an error message and not disable any port.
When a port is error-disabled, no traffic is sent or received on that port.
Interaction of Loop Detection Guard with Other Features
STP and Loop Detection Guard
When both loop detection guard and STP are enabled on a device, STP takes over monitoring the network for loops. In this case
loop-detect packets are neither received nor processed in the network.
VLANs and Loop Detection Guard
We do not recommend configuring this feature on a switch that is connected to a hub for these reasons: The hub floods traffic
to all of its interfaces. If the switch in your network is receiving traffic from the same hub, but on a port in a different
VLAN, you may be inadvertently error-disabling those destination ports. The figure below illustrates such a situation. The
port in VLAN 1 is sending traffic to the hub. The switch is also receiving traffic from the same hub, but on a port in a different
VLAN, that is, VLAN 10. If you configure loop detection guard (and you have configured the default action of error-disabling
the destination port), then the port in VLAN 10 is blocked. Configuring the option to display a message (instead of error-disabling
a port) is not recommended either, because the system displays as many messages as the number of interfaces configured in
the hub, resulting in a CPU overload.
How to Configure Loop Detection Guard
Enabling Loop Detection Guard and Error-Disabling the Required Port
The feature is disabled by default. Complete the following steps to enable loop detection guard and configure the action you
want the system to take when a loop is detected:
Command or Action
Enables privileged EXEC mode. Enter your password if prompted.
Enters interface configuration mode. Specify only a physical interface to configure loop detection guard on the device. Layer
3 ports and virtual interfaces like PortChannels, switch virtual interfaces (SVIs), and tunnels are not supported.
[ no] loopdetect
Enables loop detection guard on the device. Loopdetect frames are sent from the configured interface. Use the loopdetect command without any keyword to enable loop detection guard.
Use the no form of this command to disable this feature.
You can enable the feature on trunk ports, but a warning message is displayed, for the following reason: A trunk port carries
traffic for several VLANs, simultaneously. A loop detected in one VLAN can result in the error-disabling of all VLAN traffic
associated with the trunk port.
Specifies the frequency at which loop-detect frames are sent and the action the system takes when a loop is detected. If you
do not specify an action, the destination port is error-disabled by default.
You can configure the following:
time—Time interval to send loop-detect frame, in seconds. The range is from 0 to 10. The default is 5.
action syslog—Displays a system message and does not error-disable any port. If you use the no form of this command, the system reverts to the last configured option.
source-port—Error-disables the source port. If you use the no form of this command, the destination port is error-disabled.
In the example configuration on the left (Device(config-if)# loopdetect 7), the interface is configured to send loop-detect frames every 7 seconds, and to error-disable the destination port if a
loop is detected (The default applies, because neither the action syslog option nor the source-port option has been configured).
Returns to privileged EXEC mode.
Device# show loopdetect
Displays all the interfaces where loop detection guard is enabled, the frequency at which loop-detect packets are sent, and
the status of the physical interface.
Additional References for Configuring Loop Detection Guard
For complete syntax and usage information for the commands used in this chapter.
See the Layer 2/3 Commands section of the Command Reference (Catalyst 9600 Series Switches)
Feature History for Loop Detection Guard
This table provides release and related information for features explained in this module.
These features are available on all releases subsequent to the one they were introduced in, unless noted otherwise.
Cisco IOS XE Amsterdam 17.2.1
Loop Detection Guard
Loop detection guard prevents network loops in either networks that are not configured with STP or unmanaged devices in networks
configured with STP.
Use Cisco Feature Navigator to find information about platform and software image support. To access Cisco Feature Navigator,
go to http://www.cisco.com/go/cfn.