This chapter contains instructions for installing small form-factor pluggable (SFP) laser optical transceiver modules. It contains these sections:
The Gigabit Ethernet ports on these modules are used primarily for backbone interconnection of other high-performance switches and routers.
A SFP is a hot-swappable input/output device that plugs into the SFP ports, linking the switch with the fiber-optic network. (See Figure 4-1.) The following SFP media types are supported:
The following sections describe how to install, remove, and maintain small form factor pluggables (SFPs).
The Cisco 4948 switch has four ports that can be configured with any combination of SFP modules with LC connectors, as shown in Figure 4-1. The interface configuration mode command media-type sfp | rj45 can be used to configure the media type for these ports in the switch software and determines whether the SFP or the RJ-45 connector is used. The default is SFP.
Note You must insert the SFP with the latching mechanism reversed on SFP port 46 and port 48.
Figure 4-1 Connecting LC Connectors to the SFP Module
The SFP modules have three different types of latching devices used to secure and detach the SFP module from a switching module port. The three types of SFP modules are described in the following sections:
Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051
The Mylar tab SFP module (see Figure 4-2) has a tab that you must pull to remove the module from a switching module port.
Figure 4-2 Mylar Tab SFP Module
To insert the Mylar tab SFP module into a switching module port, line up the SFP module with the port, and slide it into place. (See Figure 4-3.)
Figure 4-3 Inserting a Mylar Tab SFP Module
To remove the SFP module from the switching module port, pull the tab gently in a slightly downward direction until it disengages from the port, and then pull the SFP module out. (See Figure 4-4.)
Figure 4-4 Removing a Mylar Tab SFP Module
Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051
The actuator/button SFP module (see Figure 4-5) has a button that you must push to remove the SFP module from a switching module port.
Figure 4-5 Actuator/Button SFP Module
To insert the actuator/button SFP module into a switching module port, line up the SFP module with the port, and slide it in until the actuator/button clicks into place. (See Figure 4-6.) Be sure not to press the actuator/button as you insert the SFP module because you might inadvertently disengage the SFP module from the port.
Figure 4-6 Inserting an Actuator/Button SFP Module
To remove an actuator/button SFP module from a switching module port, follow this procedure:
Step 1 Gently press the actuator/button on the front of the SFP module until it clicks and the latch mechanism activates, releasing the SFP module from the port. (See Figure 4-7.)
Step 2 Grasp the actuator/button between your thumb and index finger, and carefully pull the SFP module from the port.
Figure 4-7 Removing an Actuator/Button SFP Module from a Port
Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051
The bale-clasp SFP module (see Figure 4-8) has a bale clasp that you use to secure the SFP module in a switching module port.
Figure 4-8 Bale-clasp SFP Module
To insert a bale-clasp SFP module into a switching module port, follow these steps:
Step 1 Close the bale-clasp before inserting the SFP module.
Step 2 Line up the SFP module with the port, and slide it into the port. (See Figure 4-9.)
Figure 4-9 Inserting a Bale-clasp SFP Module into a Switching Port
To remove a bale-clasp SFP module from a switching module port, follow these steps:
Step 1 Open the bale clasp on the SFP module with your index finger in a downward direction as shown in Figure 4-10. If the bale clasp is obstructed and you cannot use your index finger to open it, use a small, flat-blade screwdriver or other long, narrow instrument to open the bale clasp, as shown in Figure 4-11.
Step 2 Grasp the SFP module between your thumb and index finger, and carefully remove it from the switching module port, as shown in Figure 4-10.
Figure 4-10 Removing a Bale-clasp SFP Module with Your Index Finger
Figure 4-11 Removing a Bale-clasp SFP Module with a Flat-Blade Screwdriver