- show fabricpath conflict
- show fabricpath ftag
- show fabricpath isis
- show fabricpath isis adjacency
- show fabricpath isis database
- show fabricpath isis ftag
- show fabricpath isis hostname
- show fabricpath isis interface
- show fabricpath isis ip mroute
- show fabricpath isis ip redistribute mroute
- show fabricpath isis protocol
- show fabricpath isis route
- show fabricpath isis rrm
- show fabricpath isis spf-log
- show fabricpath isis srm
- show fabricpath isis ssn
- show fabricpath isis statistics
- show fabricpath isis switch-id
- show fabricpath isis topology summary
- show fabricpath isis traffic
- show fabricpath isis trees
- show fabricpath isis vlan-range
- show fabricpath load-balance
- show fabricpath load-balance multicast
- show fabricpath load-balance unicast
- show fabricpath route
- show fabricpath switch-id
- show fabricpath system-id
- show fabricpath timers
- show fabricpath topology
- show feature-set
- show mroute
- show multicast trees
- show running-config fabricpath
Show Commands
This chapter describes the Cisco NX-OS FabricPath show commands.
show fabricpath conflict
To display information about the conflicts in the FabricPath network, use the show fabricpath conflict command.
show fabricpath conflict {all [detail] | link [detail] | switch-id [detail] | transitions [detail]}
Syntax Description
all |
Displays all the conflicts. |
detail |
(Optional) Displays the details. |
link |
Displays all the links. |
switch-id |
Displays the switch IDs. |
transitions |
Displays the transitions. |
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display detailed information about the conflicts in the FabricPath network:
switch# show fabricpath conflict all detail
No Ports under Fabricpath control
No Switch id Conflicts
No transitions in progress
switch#
Related Commands
|
|
---|---|
show running-config fabricpath |
Displays current FabricPath configuration. |
show fabricpath ftag
To display information about the FabricPath FTAG, use the show fabricpath ftag command.
show fabricpath ftag
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the information about the FabricPath FTAG:
switch# show fabricpath ftag
No ftag values present
switch#
Related Commands
|
|
---|---|
show running-config fabricpath |
Displays the current FabricPath configuration. |
show fabricpath isis
To display the FabricPath Intermediate System-to-Intermediate System (IS-IS) adjacency database, use the show fabricpath isis command.
show fabricpath isis
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display detailed information about the IS-IS adjacency:
switch# show fabricpath isis
Fabricpath IS-IS domain : default
System ID : 0005.73a3.ba3c IS-Type : L1
SAP : 432 Queue Handle : 11
Maximum LSP MTU: 1492
Graceful Restart enabled. State: Inactive
Last graceful restart status : none
Metric-style : advertise(wide), accept(wide)
Start-Mode: Complete [Start-type configuration]
Area address(es) :
00
Process is up and running
CIB ID: 4
Interfaces supported by Fabricpath IS-IS :
Level 1
Authentication type and keychain not configured
Authentication check specified
MT-0 Ref-Bw: 400000
Address family Swid unicast :
Number of interface : 0
Distance : 115
L1 Next SPF: Inactive
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show running-config fabricpath |
Displays the FabricPath running system configuration information. |
show fabricpath isis adjacency
To display the FabricPath Intermediate System-to-Intermediate System (IS-IS) adjacency database, use the show fabricpath isis adjacency command.
show fabricpath isis adjacency [interface {ethernet slot/[QSFP-module]/port | port-channel channel-number} | detail | summary | system-id sid]
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display detailed information about the IS-IS adjacency:
switch# show fabricpath isis adjacency detail
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis database
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) link-state packet (LSP) database, use the show fabricpath isis database command.
show fabricpath isis database [l1] [level-1] [mgroup] [detail | summary] [sid] {[zero-sequence] | [router-id] | [adjacency]}
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS LSP database:
switch# show fabricpath isis database
Fabricpath IS-IS domain: default LSP database
LSPID Seq Number Checksum Lifetime A/P/O/T
O2-48_Mgmt-2.00-00 * 0x00000008 0x2F9D 1073 0/0/0/1
switch#
This example shows how to display the IS-IS Level-1 routing link state database:
switch# show fabricpath isis database level-1
Fabricpath IS-IS domain: default LSP database
LSPID Seq Number Checksum Lifetime A/P/O/T
O2-48_Mgmt-2.00-00 * 0x00000008 0x2F9D 1041 0/0/0/1
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis ftag
To display Intermediate System-to-Intermediate System (IS-IS) FTAG values associated with the trees in the topology, use the show fabricpath isis ftag command.
show fabricpath isis ftag [multidestination tree-id]
Syntax Description
multidestination |
(Optional) Displays the multidestination information. |
tree-id |
Tree identifier. The range is from 1 to 2. |
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display IS-IS FTAG multidestination information:
switch# show fabricpath isis ftag multidestination 1
Fabricpath IS-IS domain: default
Fabricpath IS-IS Ftag Database
Legend: C - Confirmed, T - tentative
MT-0
PrimaryTree
Multidestination-2 0 [C]
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis hostname
To display FabricPath Intermediate System-to-Intermediate System (IS-IS) hostname table information, use the show fabricpath isis hostname command.
show fabricpath isis hostname [detail]
Syntax Description
detail |
(Optional) Displays the detailed IS-IS information. |
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS hostname table:
Switch# show fabricpath isis hostname detail
Fabricpath IS-IS domain: default dynamic hostname table
Level LSP ID Dynamic hostname
1 0005.73a3.ba3c.00-00* O2-48_Mgmt-2
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis interface
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) interface, use the show fabricpath isis interface command.
show fabricpath isis interface {brief | ethernet slot/[QSFP-module]/port | port-channel channel-number}
Syntax Descriptionshow fabricpath isis interface {brief | ethernet slot/chassis number | port-channel channel-number}
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the brief information about the FabricPath IS-IS interface:
switch1# show fabricpath isis interface brief
This example shows how to display the FabricPath IS-IS interface information for an Ethernet interface:
switch1# show fabricpath isis interface ethernet 1/2
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis ip mroute
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) multicast route, use the show fabricpath isis ip mroute command.
show fabricpath isis ip mroute [vlan vlan-id [group group-id [source source-id]]]
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the IS-IS mroute:
switch# show fabricpath isis ip mroute
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis ip redistribute mroute
To display the FabricPath Intermediate System-to-Intermediate System (IS-IS) redistribute multicast route information, use the show fabricpath isis ip redistribute mroute command.
show fabricpath isis ip redistribute mroute [vlan vlan-id [group group-id [source source-id]]]
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the FabricPath IS-IS redistribute mroute information:
switch# show fabricpath isis ip redistribute mroute
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis protocol
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) protocol, use the show fabricpath isis protocol command.
show fabricpath isis protocol
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS protocol:
switch1# show fabricpath isis protocol
Fabricpath IS-IS domain : default
System ID : 0005.73a3.ba3c IS-Type : L1
SAP : 432 Queue Handle : 11
Maximum LSP MTU: 1492
Graceful Restart enabled. State: Inactive
Last graceful restart status : none
Metric-style : advertise(wide), accept(wide)
Start-Mode: Complete [Start-type configuration]
Area address(es) :
00
Process is up and running
CIB ID: 4
Interfaces supported by Fabricpath IS-IS :
Level 1
Authentication type and keychain not configured
Authentication check specified
MT-0 Ref-Bw: 400000
Address family Swid unicast :
Number of interface : 0
Distance : 115
L1 Next SPF: Inactive
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis route
To display the FabricPath Intermediate System-to-Intermediate System (IS-IS) routing table for unicast routes, use the show fabricpath isis route command.
show fabricpath isis route [summary | detail]
Syntax Description
summary |
(Optional) Displays a summary of the IS-IS adjacency information. |
detail |
(Optional) Displays the detailed IS-IS adjacency detail information. |
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display detailed information about the IS-IS route:
switch# show fabricpath isis route detail
Fabricpath IS-IS domain: default MT-0
Topology 0, Tree 0, Swid routing table
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis rrm
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) Retransmit-Routing-Message (RRM), use the show fabricpath isis rrm command.
show fabricpath isis rrm [gm] {ethernet slot/port | port-channel channel-number}
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the FabricPath IS-IS RRM information:
switch# show fabricpath isis rrm gm ethernet 2/2
Related Commands
|
|
---|---|
fabricpath domain default |
Enables the FabricPath Layer 2 IS-IS. |
show fabricpath isis spf-log
To display information about FabricPath Intermediate System-to-Intermediate System (IS-IS) shortest-path-first (SPF) calculation statistics, use the show fabricpath isis spf-log command.
show fabricpath isis spf-log [detail]
Syntax Description
detail |
(Optional) Displays the detailed IS-IS SPF information. |
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the detailed information about the FabricPath IS-IS SPF:
switch1# show fabricpath isis spf-log detail
Fabricpath IS-IS domain: default SPF information
Total number of SPF calculations: 1
Log entry (current/max): 1/20
Log entry: 01, Ago: 02:32:37, Date: Tue Oct 25 03:41:00 2011
Level Instance Init SPF IS Update URIB Update Total
1 0x00000001 0.000062 0.000009 0.000009 0.000009 0.000411
Level Node Count Changed Reason
1 1 2 0 Switch-id updated
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis srm
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) Send-Routing-Message (SRM), use the show fabricpath isis srm command.
show fabricpath isis srm [gm] {ethernet slot/[QSFP-module]/port | port-channel channel-number}
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS SRM:
switch# show fabricpath isis srm gm ethernet 2/2
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis ssn
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) Send-Sequence-Number (SSN), use the show fabricpath isis ssn command.
show fabricpath isis ssn [gm] {ethernet slot/port | port-channel channel-number}
Syntax Description
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display FabricPath IS-IS Send-Sequence-Number information:
switch# show fabricpath isis ssn gm port-channel 400
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis statistics
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) protocol statistics, use the show fabricpath isis statistics command.
show fabricpath isis statistics
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS protocol statistics:
switch# show fabricpath isis statistics
Fabricpath IS-IS domain: default
SPF calculations: 1
LSPs sourced: 2
LSPs refreshed: 18
LSPs purged: 0
Buffers U2RIB: 0
Buffers M2RIB: 0
Buffers PIXM: 0
Swid Updates: 2
Ftag Updates: 0
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis switch-id
To display switch IDs and reachability information in the topology, use the show fabricpath isis switch-id command.
show fabricpath isis switch-id
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the switch ID database:
switch# show fabricpath isis switch-id
Fabricpath IS-IS domain: default
Fabricpath IS-IS Switch-ID Database
Legend: C - Confirmed, T - tentative, W - swap
S - sticky, E - Emulated Switch
'*' - this system
System-ID Primary Secondary Reachable Bcast-Priority
MT-0
0005.73a3.ba3c* 2590[C] 0[C] Yes 64
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis topology summary
To display information about the Intermediate System-to-Intermediate System (IS-IS) summary topology, use the show fabricpath isis topology summary command.
show fabricpath isis topology summary
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Global configuration mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS summary topology:
switch# show fabricpath isis topology summary
Fabricpath IS-IS domain: default FabricPath IS-IS Topology Summary
MT-0
Configured interfaces:
Number of trees: 2
Tree id: 1, ftag: 0, root system: 0000.0000.0000, 0
Tree id: 2, ftag: 0, root system: 0000.0000.0000, 0
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis traffic
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) traffic, use the show fabricpath isis traffic command.
show fabricpath isis traffic {ethernet lot/[QSFP-module]/port | port-channel channel-number}
Syntax Description
Command Default
None
Command Modes
Global configuraion mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS traffic:
switch1# show fabricpath isis traffic
Fabricpath IS-IS domain: default
Fabricpath IS-IS Traffic:
PDU Received Sent RcvAuthErr OtherRcvErr ReTransmit
P2P-IIH 0 0 0 0 n/a
CSNP 0 0 0 0 n/a
PSNP 0 0 0 0 n/a
LSP 0 0 0 0 0
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis trees
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) trees, use the show fabricpath isis trees command.
show fabricpath isis trees [multidestination tree-id]
Syntax Description
multidestination |
(Optional) Displays the multidestination information. |
tree-id |
Tree identifier. The range is from 1 to 2. |
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath IS-IS tree multidestination:
switch# show fabricpath isis trees multidestination 1
Fabricpath IS-IS domain: default
Note: The metric mentioned for multidestination tree is from the root of that tr
ee to that switch-id
MT-0
Topology 0, Tree 1, Swid routing table
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath isis vlan-range
To display VLANs in the FabricPath Intermediate System-to-Intermediate System (IS-IS) topology, use the show fabricpath isis vlan-range command.
show fabricpath isis vlan-range
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display VLANs in the FabricPath IS-IS topology:
switch# show fabricpath isis vlan-range
Fabricpath IS-IS domain: default
MT-0
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show fabricpath load-balance
To display FabricPath load-balancing information, use the show fabricpath load-balance command.
show fabricpath load-balance
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
Note The show fabricpath load-balance cannot be executed by any users without admin privileges.
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display FabricPath load-balancing information:
switch# show fabricpath load-balance
ECMP load-balancing configuration:
L3/L4 Preference: Mixed (L2, L3 and L4)
Hash Control: Symmetric
Rotate amount: 7 bytes
Use VLAN: TRUE
switch#
Related Commands
|
|
---|---|
fabricpath load-balance |
Displays FabricPath load-balancing parameters. |
show fabricpath load-balance multicast
To display FabricPath load-balancing information for the multicast load-balancing scheme, use the show fabricpath load-balance multicast command.
show fabricpath load-balance multicast ftag-selected vlan vlan-ID macg MAC-addr
Syntax Description
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display FabricPath load-balancing forwarding information for the multicast load-balancing scheme:
switch# show fabricpath load-balance multicast ftag-selected vlan 10 macg 0100.5E10.1010
Related Commands
|
|
---|---|
fabricpath load-balance |
Displays FabricPath load-balancing parameters. |
show fabricpath load-balance unicast
To display FabricPath load-balancing information for the unicast load-balancing scheme, use the show fabricpath load-balance unicast command.
show fabricpath load-balance unicast forwarding-path ftag ftag-ID switchid switch-ID src-mac MAC-addr dst-mac MAC-addr [dst-ip ip-addr] [dst-ipv6 ipv6-addr] [l4-dst-port l4-dest-port] [l4-src-port l4-src-port] [src-ip ip-addr] [src-ipv6 ipv6-addr] [vlan vlan-ID]
Syntax Description
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display FabricPath load-balancing forwarding information for the unicast load-balancing scheme:
switch# show fabricpath load-balance unicast forwarding-path ftag 1 switchid 200 src-mac 00:10:20:30:40:50 dst-mac 00:30:40:50:60:70 vlan 200
This example shows how to display FabricPath load-balance hashing information for the unicast load-balancing scheme:
switch# show fabricpath load-balance unicast forwarding-path ftag 1 switchid 232 src-mac 0000.1234.5678 dst-mac 0000.3452.4567 src-ipv6 12:34::56:78 dst-ipv6 01:34::56:78 l4-dst-port 100 l4-src-port 435 vlan 200
Missing params will be substituted by 0's.
crc8_hash: 229
This flow selects interface Po400
switch#
Related Commands
|
|
---|---|
fabricpath load-balance |
Displays FabricPath load-balancing parameters. |
show fabricpath route
To display FabricPath route information, use the show fabricpath route command.
show fabricpath route [detail [hex] | hex | topology {topology_ID [switchid switch-ID] | all} [detail | hex]]
Syntax Description
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the detailed information about the FabricPath route:
switch# show fabricpath route detail
FabricPath Unicast Route Table
'a/b/c' denotes ftag/switch-id/subswitch-id
'[x/y]' denotes [admin distance/metric]
ftag 0 is local ftag
subswitch-id 0 is default subswitch-id
FabricPath Unicast Route Table for Topology-Default
0/2590/0, number of next-hops: 0
via ---- , [60/0], 0 day/s 02:57:18, local
switch#
This example shows how to display the information about the FabricPath route:
switch# show fabricpath route
FabricPath Unicast Route Table
'a/b/c' denotes ftag/switch-id/subswitch-id
'[x/y]' denotes [admin distance/metric]
ftag 0 is local ftag
subswitch-id 0 is default subswitch-id
FabricPath Unicast Route Table for Topology-Default
0/2590/0, number of next-hops: 0
via ---- , [60/0], 0 day/s 02:58:05, local
switch#
Related Commands
|
|
---|---|
show running-config fabricpath |
Displays the current FabricPath configuration. |
show fabricpath switch-id
To display the FabricPath switch ID, use the show fabricpath switch-id command.
show fabricpath switch-id [local]
Syntax Description
local |
(Optional) Displays the local switch ID information. |
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the FabricPath switch ID:
switch# show fabricpath switch-id
FABRICPATH SWITCH-ID TABLE
Legend: '*' - this system
=========================================================================
SWITCH-ID SYSTEM-ID FLAGS STATE STATIC EMULATED
----------+----------------+------------+-----------+--------------------
*2590 0005.73a3.ba3c Primary Confirmed No No
Total Switch-ids: 1
O2-48_Mgmt-2(config)#
O2-48_Mgmt-2(config)# show fabricpath s?
switch-id Switch ID
system-id System-id
switch#
This example shows how to display the local FabricPath switch ID:
switch# show fabricpath switch-id local
Switch-Id: 2590
System-Id: 0005.73a3.ba3c
switch#
Related Commands
|
|
---|---|
fabricpath switch-id (FabricPath) |
Displays the FabricPath switch ID. |
show fabricpath system-id
To display information about the FabricPath network by the system ID, use the show fabricpath system-id command.
show fabricpath system-id {mac-address}
Syntax Description
mac-address |
MAC address. |
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display information about the FabricPath network by the system ID:
switch# show fabricpath system-id 0005.73a3.ba3c
Switch-Id: 2590
State: Confirmed
switch#
Related Commands
|
|
---|---|
show running-config fabricpath |
Displays information about the current FabricPath configuration. |
show fabricpath timers
To display settings for the allocate-delay, linkup-delay, and transition-delay timers for the FabricPath network by the system ID, use the show fabricpath timers command.
show fabricpath timers
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display FabricPath timers:
switch# show fabricpath timers
Allocate Delay Timer : 10
Transition Delay Timer : 10
Link-up Delay Timer : 10
switch#
Related Commands
|
|
---|---|
fabricpath timers |
Configures the FabricPath timers. |
show fabricpath topology
To display information about the FabricPath Intermediate System-to-Intermediate System (IS-IS) topology, use the show fabricpath topology command.
Note The Cisco Nexus switch supports only two topologies; the default or base topology (topology 0), and another optional topology (for example, topology 1).
show fabricpath topology [topology-ID {ftag [active | multicast | unicast] | interface [ethernet slot/[QSFP-module]/port | port-channel channel-number] | vlan [active]} | detail | ftag [active | multicast | unicast] | interface [ethernet slot/[QSFP-module]/port | port-channel channel-number | vlan [active]] | vlan [active]]
Syntax Description
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display VLANs in a Layer 2 topology:
switch# show fabricpath topology 0 vlan
Topo-Description TPG-ID Configured VLAN List
------------------------ --------- ----------------------------
0 0 1-4095
switch#
This example shows how to display interface topology information:
switch# show fabricpath topology 0 interface
This example shows how to display active multicast FTAGs:
switch# show fabricpath topology 0 ftag
This example shows how to display the FabricPath topology interface VLANs:
switch# show fabricpath topology interface ethernet 2/1 vlan
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |
show feature-set
To display the status of all feature sets on the switch, use the show feature-set command.
show feature-set [services feature-set-name]
Syntax Description
services |
Displays the services associated with a feature set. |
feature-set-name |
Name of the service or feature set. |
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the status of a feature set:
switch# show feature-set
Feature Set Name ID State
-------------------- -------- --------
fabricpath 2 enabled
virtualization 4 uninstalled
switch#
This example shows how to display the services associated with the FabricPath feature set:
switch# show feature-set services fabricpath
u2rib
drap
isis_fabricpath
3 services in feature set fabricpath
switch#
Related Commands
|
|
---|---|
feature-set fabricpath |
Enables the FabricPath feature set on the switch. |
show mroute
To display the Layer 2 (l2) or FabricPath multicast route database, use the show mroute command.
show {l2 | fabricpath} mroute {[vdc_omf] | [vlan vlanid] {{[omf] | [flood] | [source {srcaddr | ipv6srcaddr}] [group {groupaddr | ipv6groupaddr}]} [resolved] [ftag ftag-id] [hex]}}
Syntax Description
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
Note l2 can be used interchangeably with FabricPath.
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the VLAN flood routes in the FabricPath multicast route database:
switch# show fabricpath mroute flood
This example shows how to display the resolved switch ID of the next hop's underlying interfaces:
switch# show l2 mroute resolved
Related Commands
|
|
---|---|
fabricpath load-balance |
Displays FabricPath load-balancing parameters. |
show running-config fabricpath |
Displays the current FabricPath configuration. |
show multicast trees
To display the Layer 2 (l2) or FabricPath multicast tree database, use the show multicast trees command.
show {l2 | fabricpath} multicast trees [topo topo-id] [ftag ftag-id] [hex]
Syntax Description
Command Default
None
Command Modes
EXEC mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display the FabricPath multicast tree database:
switch# show fabricpath multicast trees
This example shows how to display the FTAG number of the Layer 2 multicast trees:
switch# show l2 multicast trees ftag 1
This example shows how to display the Layer 2 multicast tree database:
switch# show l2 multicast trees
Related Commands
|
|
---|---|
show l2 route |
Displays FabricPath route information. |
show fabricpath route |
Displays FabricPath route information. |
show running-config fabricpath
To display FabricPath running system configuration information, use the show running-config fabricpath command.
show running-config fabricpath [domain default | switch-id | topology] [all]
Syntax Description
Command Default
None
Command Modes
Any command mode
Command History
|
|
---|---|
6.0(2)N1(1) |
This command was introduced. |
Usage Guidelines
This command requires an Enhanced Layer 2 license.
Examples
This example shows how to display FabricPath running system configuration information:
switch# show running-config fabricpath
!Command: show running-config fabricpath
!Time: Tue Oct 25 07:55:05 2011
version 6.0(2)N1(1)
install feature-set fabricpath
feature-set fabricpath
vpc domain 1
fabricpath domain default
switch#
Related Commands
|
|
---|---|
fabricpath domain default |
Enables FabricPath Layer 2 IS-IS. |