The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter describes the Cisco Nexus 1010 commands that begin with the letter V.
To enter virtual service blade configuration mode and configure a virtual service, use the virtual-service-blade command. To remove a virtual service configuration, use the no form of this command.
virtual-service-blade name
no virtual-service-blade name
name |
User identifier that is a case-sensitive, alphanumeric character string with a maximum of 80 characters. The name cannot contain spaces or special characters. |
None
Global configuration (config)
network-admin
When you use the no form of the command, you do not enter virtual service blade configuration mode.
|
|
4.0(4)SP1(1) |
This command was introduced. |
This example shows how to enter virtual service blade configuration mode and configure the virtual service named vsb1:
switch# configure terminal
switch(config)# virtual-service-blade vsb1
switch(config-vsb-config)#
This example shows how to remove the virtual service configuration named vsb1:
switch# configure terminal
switch(config)# no virtual-service-blade vsb1
switch(config)#
To specify the virtual service type to add to a virtual service, use the virtual-service-blade-type name command.
virtual-service-blade-type name type-name
type-name |
Name of an existing virtual service type. |
None
Virtual service blade configuration (config-vsb-config)
network-admin
|
|
4.0(4)SP1(1) |
This command was introduced. |
This example shows how to specify the VSM-3 virtual service type:
switch(config-vsb-config)# virtual-service-blade-type name vsm-3
switch(config-vsb-config)#
To specify the name of the software image file to add to a virtual service, use the virtual-service-blade-type new command.
virtual-service-blade-type new iso-file-name
iso-file-name |
Name of the new ISO software image file in the bootflash repository folder. |
None
Virtual service blade configuration (config-vsb-config)
network-admin
|
|
4.0(4)SP1(1) |
This command was introduced. |
This example shows how to specify nexus-1010.4.0.4.SV1.3.51.iso as the software image file to add to the virtual service:
switch(config-vsb-config)# virtual-service-blade-type new nexus-1010.4.0.4.SV1.3.51.iso
switch(config-vsb-config)#
To create a VLAN and enter the VLAN configuration mode, use the vlan command. To remove a VLAN, use the no form of this command.
vlan {id | dot1Q tag native}
no vlan {id | dot1Q tag native}
id |
VLAN identification number. The range is from 1 to 4094. |
dot1Q tag native |
Not supported in Cisco Nexus 1010. |
The default VLAN is VLAN 1.
Global configuration (config)
network-admin
|
|
4.0(4)SP1(1) |
This command was introduced. |
Specify a VLAN range by using a dash. For example, 1-9 or 20-30.
The dot1Q option is not supported in Cisco Nexus 1010.
This example shows how to create a VLAN and enter the VLAN configuration mode:
switch# configure terminal
switch(config)# vlan 10
switch(config-vlan)#
This example shows how to remove a VLAN:
switch# configure terminal
switch(config)# no vlan 10
switch(config)#
|
|
---|---|
exit |
Exits a configuration mode. |
interface vlan |
Applies the interface and VLAN ID to a virtual service. |