Cisco Nexus 1000V for Microsoft Hyper-V Release Notes, Release 5.2(1)SM1(5.2)

Table of Contents

Cisco Nexus 1000V for Microsoft Hyper-V Release Notes, Release 5.2(1)SM1(5.2)

Contents

Introduction

Hyper-V Webinar

Administrative Model

Software Compatibility with Microsoft Servers

Software Compatibility with the Cisco Nexus 1000V

New and Changed Information

Microsoft SCVMM Support

Nexus 1000V Multi-Hypervisor Licensing

Configuration Limits

Caveats

Open Caveats

Resolved Caveats

MIB Support

Related Documentation

Obtaining Documentation and Submitting a Service Request

Cisco Nexus 1000V for Microsoft Hyper-V Release Notes, Release 5.2(1)SM1(5.2)

---

Last Updated: October 17, 2014

This document describes the features, limitations, and caveats for the Cisco Nexus 1000V for Microsoft Hyper-V Release 5.2(1)SM1(5.2) software.

Contents

This document includes the following sections:

• Introduction
• Administrative Model
• Software Compatibility with Microsoft Servers
• Software Compatibility with the Cisco Nexus 1000V
• New and Changed Information
• Configuration Limits
• Caveats
• MIB Support
• Related Documentation
• Obtaining Documentation and Submitting a Service Request

Introduction

The Cisco Nexus 1000V provides a distributed, Layer 2 virtual switch that extends across many virtualized hosts. The Cisco Nexus 1000V manages a data center. Each server in the data center is represented as a line card in the Cisco Nexus 1000V and can be managed as if it were a line card in a physical Cisco switch.

When server virtualization is implemented, the edge of the network is pushed from the traditional network access layer, which is implemented in physical switches, to the virtual network access layer that is implemented through the software in the Server Hypervisor. The Cisco Nexus 1000V is an intelligent virtual network access layer switch that runs Cisco NX-OS, which is Cisco’s data center operating system common to all of Cisco’s data center products.

Operating inside the Microsoft Hyper-V Hypervisor, the Cisco Nexus 1000V supports the Cisco Virtual Network-Link (VN-Link) server virtualization technology to provide the following:

• Policy-based Virtual Machine (VM) connectivity
• Mobile VM security and network policy
• Nondisruptive operational model for your server virtualization and networking teams

Data center virtualization servers and VMs are not managed the same way as physical servers. Server virtualization is treated as a special deployment, leading to longer deployment time, with a greater degree of coordination among server, network, storage, and security administrators. With the Cisco Nexus 1000V, you have a consistent networking feature set and a configuration and provisioning model for both the physical and the virtual networks.

VM networks can use the same network configuration, security policy, diagnostic tools, and operational models as physical server deployments that are connected to physical switches. This unified approach to quicker deployment and troubleshooting makes virtualization environments no different from nonvirtualized deployments.

Developed with Microsoft, the Cisco Nexus 1000V is Microsoft certified and integrates with the Windows Server and Systems Center Virtual Machine Manager (SCVMM).

The Cisco Nexus 1000V consists of two basic components:

• Virtual Supervisor Module (VSM), also known as the Control Plane (CP). The VSM acts as the supervisor and contains the Cisco command-line interface (CLI), configuration, and high-level features.
• Virtual Ethernet Module (VEM), also known as the Data Plane (DP). The VEM acts as a line card and runs in each Hyper-V virtual switch to handle packet forwarding and other localized functions.

Hyper-V Webinar

Cisco offers a Cisco Nexus 1000V for Microsoft Hyper-V webinar as either a video demonstration or a PDF download. In the webinar, you can learn how the Cisco Nexus 1000V virtual access/distributed switch can simplify your Hyper-V virtual environment through a nondisruptive operational model, policy based provisioning, and a strong services ecosystem. You can also learn about the Cisco Nexus 1000V architecture, how it integrates with Microsoft SCVMM, and the networking capabilities it brings to Hyper-V environments.

Administrative Model

The Cisco Nexus 1000V for Microsoft Hyper-V consists of two distinct administrative entities that manage the environment on the same set of hardware. Each entity has its own separate goals, abilities, and responsibilities.

Server and VM policies can be set only by the server administrator through SCVMM or its management tools. Network policies can be set only by the network administrator through the VSM or its management tools.

Network and server administrators cannot make administrative changes to the system at the same time. Operations such as deployment, upgrade, configuration, and troubleshooting, can be carried out in an asynchronous fashion by administrators.

If the network administrator has set up appropriate policies, the server administrator can add, remove, and move both physical hosts and VMs, as well as install physical interfaces in hosts and add virtual interfaces to VMs.

Software Compatibility with Microsoft Servers

Ensure that the servers that run the Cisco Nexus 1000 VSM and VEM are in the Hardware Compatibility list. This release of the Cisco Nexus 1000V supports the following servers:

• Microsoft Windows Server 2012 R2
• Microsoft Windows Server 2012 SP1

For additional compatibility information, see the Cisco Nexus 1000V Compatibility Information, Release 5.2(1)SM1(5.2) .

Software Compatibility with the Cisco Nexus 1000V

This release supports upgrades from Release 5.2(1)SM1(5.1). For information about the upgrade procedure, see the Cisco Nexus 1000V for Microsoft Hyper-V Installation and Upgrade Guide, Release 5.2(1)SM1(5.2) .

---

Note If you are upgrading from the previous release to Release 5.2(1)SM1(5.2), and you have the permanent or evaluation license installed, see the Cisco Nexus 1000V for Hyper-V License Configuration Guide, Release 5.2(1)SM1(5.2) before beginning with the upgrade procedure.

---

New and Changed Information

The following software features were added in the Cisco Nexus 1000V Release 5.2(1)SM1(5.2):

• Microsoft SCVMM Support
• Nexus 1000V Multi-Hypervisor Licensing

Microsoft SCVMM Support

This release supports the Microsoft SCVMM 2012 R2. For more information, see the Cisco Nexus 1000V Compatibility Information, Release 5.2(1)SM1(5.2) .

Nexus 1000V Multi-Hypervisor Licensing

This release uses a multi-hypervisor licensing approach. For more information about licensing, see the Cisco Nexus 1000V for Hyper-V License Configuration Guide, Release 5.2(1)SM1(5.2).

---

Note If you are upgrading from the previous release to Release 5.2(1)SM1(5.2), and you have the permanent or evaluation license installed, see the Cisco Nexus 1000V for Hyper-V License Configuration Guide, Release 5.2(1)SM1(5.2) before beginning with the upgrade procedure.

---

Configuration Limits

The Cisco Nexus 1000V has the following configuration limits.

 

Component	Per VSM	Per VEM
Access control lists (ACLs)	128	—
ACL interfaces	500	216
Active VLANs	512	—
Application Control Engines (ACEs) per ACL	128	—
Failover cluster size	64	2012 (Windows server)
Hosts	64
MAC addresses	4096	32000
Multicast groups	256/32	32
NetFlow interfaces	500	216
NetFlow policies	16	8
Physical trunks	256	—
PNICs/hosts	31	—
Policy profiles	256	—
Port channels	256	8
Port profiles	1000 dynamic port profiles (vEthernet) 64 uplink dynamic port profiles	—
Port security	500	216
Private VLANs (PVLANs)	64	—
Quality of service (QoS) class maps	512	128
QoS interfaces	500	216
QoS policy maps	128	16
Segments	512	—
Switched Port Analyzer (SPAN)/Encapsulated Remote SPAN (ERSPAN) sessions	4	4
System network segments	16	—
System profiles	32	—
Virtual Ethernet (vEthernet) trunks	Not supported	—
vEthernet interfaces per port profile	1024	—
vEthernet interfaces	1000	216

Caveats

This section includes the following topics:

• Open Caveats
• Resolved Caveats

Open Caveats

The following are descriptions of the open caveats in Cisco Nexus 1000V Release 5.2(1)SM1(5.2). The ID links you to the Cisco Bug Search tool.

 

Category / ID		Open Caveat Headline
Cisco
Management
1.	CSCud60409	A Server Virtualization Switch (SVS) connection is needed in Hyper-V with HTTPS.
2.	CSCuh23791	The NSM causes a cascading failure when an uplink update fails.
3.	CSCuf65918	Change in the host IP address does not change the module IP address on a VSM.
Platform
4.	CSCuj78978	Timeout may occur when the standby comes online during an ISSU upgrade.
5.	CSCuj82718	Atomic change of uplink PP with LACP makes the host unreachable.
6.	CSCue12918	No relevant information is captured by the show tech-support svs detail command.
7.	CSCug71001	The speed shown in the show int capability command output is incorrect.
8.	CSCud36575	Multiple flows on the same CPU core reduces throughput.
Port Profile
9.	CSCuf43572	If the NetFlow monitor (NFM) configuration is applied as an interface override, the override configuration fails to show up in the running configuration.
10.	CSCua16092	ERSPAN TX is not working when the source is a promiscuous port channel and the vEthernet interface is a part of a secondary PVLAN.
11.	CSCuc98084	Module flaps are due to an HB loss during a performance test.
Quality of Service (QoS)
12.	CSCug16404	QoS statistics on the VEM get enabled after the Cisco Nexus1000V agent is restarted.
Representational State Transfer (REST)
13.	CSCue29655	TACACS or RADIUS user authentication is not supported by the REST APIs.
14.	CSCum38903	When created using REST, the port profile with the port channel and ACL combination shows a creation status as successful although it is not supported, and it fails on the VSM.
Security
15.	CSCue56757	TACACS authentication does not work on IPv6.
16.	CSCuf09114	Bulk vEthernet flaps fail with Sequence Timeout error for DHCP.
17.	CSCuf50018	The DHCP table is missing the vEthernet interface number for host vNICs.
18.	CSCug64630	The IP address table is not updating when changing an ACL.
SNMP
19.	CSCue46090	An snmpwalk command for v3 after a system switchover fails with an unknown user name.
20.	CSCue23291	The object cvnDVSPort returns the Distributed Virtual Switch (DVS) port value zero.
21.	CSCuf96620	A response timeout error is seen with an snmpwalk command on IF-MIB.
Microsoft
Virtual Machine Manager (VMM)
22.	CSCuj09369	Failed to put host in maintenance mode with vEthernet interfaces connected to the Cisco Nexus 1000v. See the following articles: http://support.microsoft.com/kb/2916613 http://support.microsoft.com/kb/2922318
23.	CSCuj62244	Refresh of ext manager (Network service) fails after an SCVMM upgrade.
24.	CSCuj62276	Operation on vEthernet fails for HA VMs after an SCVMM upgrade.
25.	CSCuj67509	A failure occurs while adding a host vNIC with PNICs.
26.	CSCud46791	Maximum ports are not being enforced.
27.	CSCue19084	Stale extension manager seen on the VMM UI.
28.	CSCue26596	Extension manager removal fails on the VMM.
29.	CSCug88520	Jobs fail as they lock while changing uplinks.
30.	CSCug88526	VM deployment with untagged VLAN fails.
Windows Server
31.	CSCum34479	When deploying management on the Cisco Nexus 1000v and the default port profile is set on the logical switch, deployment fails.
32.	CSCuj33348	WS 2012 R2 enters crash loop when logical switch is created on the Management NIC with VMQ. See the following article: http://support.microsoft.com/kb/2913659
33.	CSCug85666	Creation of the Cisco Nexus 1000V switch instance fails on the Management NIC of a Windows 2012 Server core host.
34.	CSCug33359	VM connectivity fails with the Intel NIC when the native profile is used.
35.	CSCug59479	Host crashed at netft.sys when sending broadcast traffic.

Resolved Caveats

The following are descriptions of the caveats resolved in Cisco Nexus 1000V Release 5.2(1)SM1(5.2). The ID links you to the Cisco Bug Search tool.

 

Category / ID		Open Caveat Headline
1.	CSCug65812	Remove the stale configuration from uplink network and port profile.
2.	CSCud43237	The “attach ack failed by vem” message appeared when adding more NICs to an existing uplink network.
3.	CSCug60850	Network Segmentation Manager (NSM) should check the current mode before flapping ports.
4.	CSCuc16682	An SCVMM error occurred at port classification-> dependent resources.
5.	CSCue05498	VMs get stuck in a stopping state when some VMs are powered off.
6.	CSCuh24163	A PVLAN mapping command is missing when changing the mode to PVLAN trunk from trunk.
7.	CSCue62007	An error occurs when adding Neighbor Discovery (ND) in the uplink network where the system VLAN is set.
8.	CSCuf50672	TACACS is not able to change the default authorization.
9.	CSCuf24560	Published names are ignored for network segments.
10.	CSCuh03748	SNMP gives the wrong statistics for several OIDs.
11.	CSCuh12495	An snmpquery fails for a community with a user-created SNMP group.

MIB Support

The Cisco Management Information Base (MIB) list includes Cisco proprietary MIBs and many other Internet Engineering Task Force (IETF) standard MIBs. These standard MIBs are defined in Requests for Comments (RFCs). To find specific MIB information, you must examine the Cisco proprietary MIB structure and related IETF-standard MIBs supported by the Cisco Nexus 1000V.

The MIB Support List is available at the following FTP site:

ftp://ftp.cisco.com/pub/mibs/supportlists/nexus1000v/Nexus1000VMIBSupportList.html

Related Documentation

This section lists the documents used with the Cisco Nexus 1000V for Microsoft Hyper-V.

General Information

Cisco Nexus 1000V for Microsoft Hyper-V Release Notes

Install and Upgrade

Cisco Nexus 1000V for Microsoft Hyper-V Installation and Upgrade Guide

Configuration Guides

Cisco Nexus 1000V for Microsoft Hyper-V High Availability and Redundancy Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V Interface Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V Layer 2 Switching Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V License Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V Network Segmentation Manager Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V Port Profile Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V Quality of Service Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V Security Configuration Guide

Cisco Nexus 1000V for Microsoft Hyper-V System Management Configuration Guide

Programming Guide

Cisco Nexus 1000V for Microsoft Hyper-V REST API Guide

Reference and Troubleshooting Guides

Cisco Nexus 1000V for Microsoft Hyper-V Command Reference

Cisco Nexus 1000V for Microsoft Hyper-V Troubleshooting Guide

Virtual Services Appliance Documentation

The Cisco Nexus Virtual Services Appliance (VSA) documentation is available at

http://www.cisco.com/en/US/products/ps9902/tsd_products_support_series_home.html

Virtual Security Gateway Documentation

The Cisco Virtual Security Gateway documentation is available at http://www.cisco.com/en/US/products/ps13095/tsd_products_support_series_home.html

Prime Network Services Controller

The Cisco Prime Network Services Controller documentation is available at http://www.cisco.com/en/US/partner/products/ps13213/tsd_products_support_series_home.html

Virtual Wide Area Application Services (vWAAS)

The Virtual Wide Area Application Services documentation is available at

http://www.cisco.com/en/US/products/ps6870/tsd_products_support_series_home.html

ASA 1000V Cloud Firewall

The ASA 1000V Cloud Firewall documentation is available at

http://www.cisco.com/en/US/products/ps12233/tsd_products_support_series_home.html

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation at: http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html .

Subscribe to What’s New in Cisco Product Documentation , which lists all new and revised Cisco technical documentation, as an RSS feed and deliver content directly to your desktop using a reader application. The RSS feeds are a free service.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

Internet Protocol (IP) addresses used in this document are for illustration only. Examples, command display output, and figures are for illustration only. If an actual IP address appears in this document, it is coincidental.

© 2014 Cisco Systems, Inc. All rights reserved.