The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter provides information about getting started with and understanding the IP camera. It includes the following sections:
The Cisco Video Surveillance 8020 (indoor) and 8030 (indoor/outdoor) IP Cameras are high-definition, full-functioned video endpoints with industry-leading image quality and processing power. The cameras are capable of 5MP resolution at 30 frames per second (fps) while optimizing network usage with H.264, H.265, or MJPEG compression. Contact closures and two-way audio allow integration with microphones, speakers, and access control systems. With their open, standards-based design, the cameras provide ideal platforms for integration and operation as independent devices or as part of a Cisco video surveillance network.
Key features and benefits of the Cisco Video Surveillance cameras include:
The following figures illustrate the camera:
Figure 1-1 Cisco Video Surveillance 8020 IP Camera Inner View
Figure 1-2 Cisco Video Surveillance 8020 IP Camera Outer View
Figure 1-3 Cisco Video Surveillance 8030 IP Camera Physical View
The following sections describe how to install your camera:
To perform the hardware installation of the Cisco Video Surveillance 8020 IP Camera, follow these steps:
Step 1 Make a note of the MAC address of the camera.
The MAC address is printed on the label that is attached to the camera.
Step 2 Remove the dome cover by pressing the release button.
Step 3 The camera comes with a PIR sensor. Plan your installation position so that the PIR can cover the area of your interest where the intrusion may occur. The rated detection distance is 5 meters.
Step 4 Attach the alignment sticker to a preferred location. Drill holes on the wall or ceiling to install the plastic anchor and secure the camera using the included screws.
If preferred, drill one routing hole.
Step 5 If applicable, connect DI/DO wires, 12V DC power, or audio wires to the terminal block.
Step 6 Adjust the shooting direction by turning and orienting the lens module. Use a Phillips screwdriver to loosen the retention screws on the sides.
Step 7 Adjust the shooting direction by turning and orienting the lens module. Use a Phillips screwdriver to loosen the retention screws on the sides.
To perform the hardware installation of the Cisco Video Surveillance 8030 IP Camera, follow these steps:
Step 1 Make a note of the MAC address of the camera.
The MAC address is printed on the label that is attached to the camera.
Step 2 Use the included T8 wrench to remove the dome cover. If local recording is preferred, install an SD card.
Step 3 Loosen and remove the waterproof connectors.
Step 4 Insert an Ethernet cable through the cable gland, and the rubber seal.
Step 5 Remove part of cable sheath.
Step 6 You will need an RJ45 crimping tool to attach the Ethernet wires to a connector. When done, connect the cable to the camera’s Ethernet RJ45 socket.
Step 7 If applicable, connect DI/DO wires, 12V DC power, or audio wires to the terminal block.
Step 8 Attach the included alignment sticker to a preferred location. Drill holes for mounting screws and if preferred, drill one or two routing holes.
Step 9 When fastening the screws, do not completely tighten the screws. Pass cables through the routing holes, and then mount the camera by passing the screw heads through the keyhole slots. Turn the camera counter-clock wise, and then fasten the screws.
Step 10 If you do not need to route your cables through the side opening, you can use the double-sided tape to attach a plastic stopper to the opening on the side of the camera.
Avoid using a conduit with a hex nut larger than 35mm.
Step 11 With a live view displayed on your laptop, adjust the zoom and focus to obtain an optimal image. Check the live view to ensure the image is in focus.
Step 12 Replace the desiccant bag on the camera.
Step 13 Align and install the dome cover.
Step 14 With a live view displayed on your laptop, adjust the zoom and focus to obtain an optimal image. Check the live view to ensure the image is in focus. [Include this step? If yes, do we need to tell users how to get to this live image?]
Table 1-1 describes the LEDs on the Cisco Video Surveillance IP Camera.
The recessed button (see Figure 1-1 for the 8020 or Figure 1-3 for the 8030) is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again.
The camera is compliant with SD/SDHC/SDXC 16GB / 8GB / 32GB / 64GB and other preceding standard SD cards.
The following sections provide information about deploying the camera on a network:
The camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Figure 1-5 illustrates how to connect the camera to a PoE-enabled switch via an Ethernet cable.
Figure 1-5 Connecting the Camera to a PoE-Enabled Switch
Use a PoE power injector (optional) to connect between the camera and a non-PoE switch, as shown in Figure 1-6.
Figure 1-6 Connecting the Camera to a Non-PoE Switch
Note • The camera is only to be connected to PoE networks without routing to outside plants.
Internet Connection via a Router
To set up the camera over the Internet, make sure you have a router and follow these steps:
Step 1 Connect your camera behind a router, the Internet environment is illustrated in Figure 1-7.
Figure 1-7 Connecting the Camera Via a Router
Step 2 In this case, if the Local Area Network (LAN) IP address of your camera is 192.168.0.3, forward the following ports for the camera on the router.:
If you have changed the port numbers on the Network page, open the ports accordingly on your router. For information about how to forward ports on the router, see your router documentation.
Step 3 Find out the public IP address of your router provided by your Internet Service Provider (ISP).
Use the public IP and the secondary HTTP port to access the camera from the Internet. See the “Network > General settings” section for more information.
Internet Connection with Static IP
Choose this connection type if you are required to use a static IP for the camera. See the “Network > General settings” section for more information.
Internet Connection via Point-to-Point over Ethernet (PPPoE)
Choose this connection type if you are connected to the Internet via a DSL Line. See description of PPPoE (Point-to-point over Ethernet) in the “Network Type Tab” section.
Configure the router, virtual server or firewall, so that the router can forward any data coming into a preconfigured port number to a camera on the private network, and allow data from the camera to be transmitted to the outside of the network over the same path.
When properly configured, you can access a camera behind the router using the HTTP request such as: http://122.146.57.120:8000.
If you change the port numbers on the Network configuration page, open the ports accordingly on your router. For example, you can open a management session with your router to configure access through the router to the camera within your local network. See your network administrator for router configuration if you have troubles with the configuration.
For more information about network configuration options (such as that of streaming ports), choose Configuration > Network Settings in the IP camera web-based interface. Cisco also provides the automatic port forwarding feature as an NAT traversal function with the precondition that your router must support the UPnP port forwarding feature.
On the web session, choose Configuration > Media > Image > Focus . Perform the Auto Focus function for best image. However, if you have cascaded cameras, do this one by one. Do not perform this function simultaneously on multiple cameras because the motorized lens also consume considerable power, and may cause the last camera on the line to hang.