New and Changed Commands
This list summarizes the commands which were newly added and changed in Cisco IOS XR Software, Release 5.3.x, and gives you the location where the commands are documented.
To read additional information about Cisco IOS XR Software features, see the Release Notes:
The latest versions of Cisco IOS XR Software documents are available at:
Commands Newly Added and Changed in Release 5.3.x
Command History
Command | Change Description |
---|---|
Release 5.3.2 | |
interface ipv4/ipv6 access-group |
This command was introduced. |
lpts pifib hardware police |
The np np-number keyword was added. |
show lpts pifib hardware entry |
The np np-number keyword was added. |
clear ipv6 path-mtu |
This command was introduced. |
ipv6 path-mtu enable |
This command was introduced. |
ipv6 path-mtu timeout |
This command was introduced. |
show ipv6 path-mtu |
This command was introduced. |
ntp(ipv4/ipv6) |
This command was introduced. |
dscp(ntp) |
This command was introduced. |
dscp precedence(ntp) |
This command was introduced. |
priority (QoS) |
Priority levels 4, 5, 6 and 7 are added. |
l2tp-source-ip |
This command was introduced. |
show vpdn |
The command was modified to include a new output display field, SRG-state , as part of geo redundancy support for PPPoE sessions. |
show pppoe interfaces |
The command was modified to include a new output display field, SRG-state , as part of geo redundancy support for PPPoE sessions. |
show subscriber redundancy group |
This command was modified to add the new keyword, tunnel. |
br-endpoint-address (MAP-E) |
This command was introduced. |
clear cgv6 map-e statistics |
This command was introduced. |
show cgv6 map-e statistics |
This command was introduced. |
g709 fec |
The high-gain-sd-fec and long-haul-sd-fec keywords were introduced on the A9K-400G-DWDM-TR line card. |
lacp non-revertive |
This command was introduced. |
show bundle |
The "Non-revertive" output field was added. |
entropy-label |
This command was introduced. |
top-label-hash |
This command was introduced. |
show mpls forwarding tunnels | |
cisco-extension |
This command was introduced. |
fast-repair |
This command was introduced. |
service-policy apply-order pbr qos |
This command was introduced. |
ping pseudowire (AToM) |
The pseudowire FEC129 AII-type 1 is supported. |
ssm map |
The keywords "query" and "DNS" were introduced to configure DNS-based SSM mapping. |
cef platform lsm frr-holdtime |
This command was introduced. |
show configuration commit changes |
Support was added for the all keyword. |
radius-server attribute 11 default direction inbound |
This command was introduced. |
telnet satellite |
This command was introduced. |
upgrade on-connect |
This command was introduced. |
advertise |
This command was introduced. |
default-originate |
This command is supported in L2VPN EVPN address family group configuration mode. |
graceful-maintenance |
This command was introduced. |
host-reachability protocol bgp |
This command was introduced. |
import |
This command was introduced. |
is-backup-path |
This command was introduced. |
is-best-path |
This command was introduced. |
import |
This command was introduced. |
is-multi-path |
This command was introduced. |
show bgp |
The command output was modified to include graceful maintenance feature information. |
show bgp community |
The graceful-shutdown keyword was added. |
show bgp l2vpn |
The show command output is updated to display Data Center Interconnect (DCI) Gateway related fields and details. |
show bgp neighbors |
The command was modified to include graceful maintenance feature information. The command output was modified display TCP MSS information. |
show bgp process |
The command output was modified to include graceful maintenance feature information. |
show bgp vrf |
The show command output is updated to display Data Center Interconnect (DCI) Gateway related fields and details. |
show tcp pcb |
This command was introduced. |
tcp mss |
This command was introduced. |
tcp mss inheritance-disable |
This command was introduced. |
destination prefix |
This command was introduced. |
source prefix |
This command was introduced. |
bfd fast-detect |
The bfd fast-detect strict-mode command was supported in the following modes: OSPFv3 router configuration, OSPFv3 area configuration, and OSPFv3 area interface configuration. |
autoroute announce |
The ip2mpls option was introduced to avoid labeled segments looping back to the source at the SR-TE tunnel ingress. |
attribute-set |
The segment routing option was introduced. |
explicit-path |
This command was introduced. |
fast reroute |
The per-prefix ti-lfa option was introduced for segment routing tunnels. |
path-selection |
This command was introduced for segment routing. |
tunnel-te |
This command was introduced. |
segment-routing prefix-sid-map advertise-local |
This command was introduced. |
segment-routing prefix-sid-map receive disable |
This command was introduced. |
segment-routing sr-prefer prefix-list |
This command was introduced. |
show rpl community-set |
The command output was modified to display graceful maintenance feature information. |
license cm update |
This command was introduced. |
install upgrade source |
This command was introduced. |
cipher-suite (macsec-policy) |
This command was introduced. |
conf-offset (macsec-policy) |
This command was introduced. |
key-string (keychain) |
This command was introduced. |
key-server-priority (macsec-policy) |
This command was introduced. |
lifetime |
This command was introduced. |
macsec-policy |
This command was introduced. |
macsec |
This command was introduced. |
security-policy |
This command was introduced. |
window-size |
This command was introduced. |
overlap-tap enable |
This command was introduced. |
show ssh |
The command output was enhanced to reflect multichannel and subsystem support for ssh. |
show l2vpn forwarding |
The show command output is enhanced to display MAC Move Counters information. |
show l2vpn bridge-domain (VPLS) |
The show command output is enhanced to display the MAC move counter information. |
show l2vpn forwarding bridge-domain (VPLS) |
The show command output was enhanced to display MAC Move Counter information. |
Release 5.3.1 |
|
ipv6 virtual address |
This command was introduced. |
enforce heartbeat-to-mag (pmipv6-lma) |
This command was introduced. |
redistribute home-address (pmipv6-lma) |
This command was introduced. |
show ipv6 mobile pmipv6 lma stats |
The keyword customer-name was added to this command. |
aaa server radius dynamic-author |
The command was modified to add IPv6 address support for aaa server radius dynamic-author client configuration, as part of RADIUS over IPv6 feature. |
radius-server host (BNG) |
The command was modified to add IPv6 address support for the RADIUS server host configuration. |
aaa group server radius (BNG) |
The command was modified to add IPv6 address support for server and server-private configuration, as part of RADIUS over IPv6 feature. |
nat-mode |
The predefined keyword was introduced. |
show controller dwdm |
g709 standard FEC mode is enabled by default. |
lldp |
The lldp subinterfaces enable was introduced. |
service |
This command was modified to enable CFM on multipoint-to-multipoint cross connects. |
show ethernet cfm interfaces statistics |
The command is enhanced to retrieve PM statistics from satellite. |
show ethernet cfm local meps |
The show ethernet cfm local meps verbose command output is modified to include counts for more packet types (DMM, DMR, SLM, SLR, LMM, LMR), and exclude rows in which the sent and received packet count is zero. |
minimum preferred links |
This command was introduced. |
nv satellite sla processing disable |
This command was introduced. |
bgp policy propagation input flow-tag |
This command was introduced. |
maximum-prefix (BGP) |
The discard-extra-paths keyword was added. |
neighbor internal-vpn-client |
This command was introduced. |
bfd mode |
This command was introduced. |
show commit changes diff |
Policy-map was supported. |
clear netconf-yang agent rate-limit |
This command was introduced. |
netconf-yang agent session |
This command was introduced. |
netconf-yang agent rate-limit |
This command was introduced. |
show netconf-yang rate-limit |
This command was introduced. |
load-balancing flow-label |
In the L2VPN bridge group bridge-domain vfi autodiscovery BGP signalling submode, the static keyword is optional. |
rd (L2VPN) |
For the L2VPN bridge domain VFI autodiscovery BGP and L2VPN cross-connect mp2mp autodiscovery BGP submodes, the index value associated with the IP address can take values higher than 32767 in the range from 0 to 65535 |
show l2vpn forwarding |
The show command output was enhanced to display VXLAN anycast gateway parameters. |
show l2vpn bridge-domain (VPLS) |
The show command output was enhanced to display VXLAN anycast gateway parameters. |
show l2vpn forwarding bridge-domain (VPLS) |
The show command output was enhanced to display VXLAN anycast gateway parameters. |
anycast source-interface loopback |
This command was introduced. |
show nve interface |
The show command output was enhanced to display VXLAN anycast gateway parameters. |
Release 5.3.0 |
|
aaa accounting service |
The diameter keyword was added for DIAMETER protocol support in BNG. |
aaa accounting subscriber |
The diameter keyword was added for DIAMETER protocol support in BNG. |
aaa authentication subscriber |
The diameter keyword was added for DIAMETER protocol support in BNG. |
aaa authorization policy-intf |
This command was introduced. |
aaa authorization prepaid |
This command was introduced. |
aaa authorization subscriber |
The diameter keyword was added for DIAMETER protocol support in BNG. |
aaa group server diameter (BNG) |
This command was introduced. |
accounting prepaid |
This command was introduced. |
address (DIAMETER) |
This command was introduced. |
clear diameter peer |
This command was introduced. |
clear diameter statistics |
This command was introduced. |
destination host |
This command was introduced. |
destination realm |
This command was introduced. |
diameter attribute list |
This command was introduced. |
diameter gx |
This command was introduced. |
diameter gx retransmit |
This command was introduced. |
diameter gx tx-timer |
This command was introduced. |
diameter gy |
This command was introduced. |
diameter gy retransmit |
This command was introduced. |
diameter gy tx-timer |
This command was introduced. |
diameter origin host |
This command was introduced. |
diameter origin realm |
This command was introduced. |
diameter peer |
This command was introduced. |
diameter tls trustpoint |
This command was introduced. |
diameter vendor supported |
This command was introduced. |
ip vrf forwarding |
This command was introduced. |
peer-type |
This command was introduced. |
prepaid-config |
This command was introduced. |
server (DIAMETER) |
This command was introduced. |
source-interface (DIAMETER) |
This command was introduced. |
test aaa group diameter |
This command was introduced. |
timer (DIAMETER) |
This command was introduced. |
transport (DIAMETER) |
This command was introduced. |
transport security-type |
This command was introduced. |
show diameter |
This command was introduced. |
show diameter gx |
This command was introduced. |
show diameter gy |
This command was introduced. |
show diameter nas |
This command was introduced. |
show diameter peer |
This command was introduced. |
show checkpoint dynamic process (DIAMETER) |
This command was introduced. |
lpts punt excessive-flow-trap dampening |
This command was introduced. |
lpts punt excessive-flow-trap interface-based-flow |
This command was introduced. |
lpts punt excessive-flow-trap non-subscriber-interfaces |
The command was modified to add mac keyword to enable MAC-based EPFT on non-subscriber interfaces. |
lpts punt excessive-flow-trap penalty-rate |
The command was modified to add unclassified keyword to set the penalty police rates for unclassified source MAC. |
show lpts punt excessive-flow-trap |
This command was modified to add unclassified keyword. |
ipsubscriber subscriber-templates |
This command was introduced. |
show ipsubscriber interface |
A new output field, Template ID, was added for show ipsubscriber interface internal command. |
show ipsubscriber template-interface |
This command was introduced. |
show subscriber database |
A new output field, Template Interface Id, was added to show subscriber database session subscriber-label command, to indicate whether the subscriber uses templates or not. |
show subscriber database template |
This command was introduced. |
show subscriber feature accounting |
The show command output was extended to display the prepaid feature information. |
deny (IPv4) |
The ABF feature can be configured along with object-groups while defining an ACEs (Access Control Entry). |
deny (IPv6) |
The ABF feature can be configured along with object-groups while defining an ACEs (Access Control Entry). |
object-group network |
The object-group feature can be configured along with ABF while defining an ACEs (Access Control Entry). |
object-group port |
The ABF feature can be configured along with object-groups while defining an ACEs (Access Control Entry). |
permit (IPv4) |
The ABF feature can be configured along with object-groups while defining an ACEs (Access Control Entry). |
permit (IPv6) |
The ABF feature can be configured along with object-groups while defining an ACEs (Access Control Entry). |
aaa accounting (pmipv6-lma) |
This command was introduced. |
address (pmipv6-lma-mll-cust-tpt) |
This command was introduced. |
auth-option (pmipv6-lma-mll-cust) |
This command was introduced. |
bce (pmipv6-lma-mll-cust) |
This command was introduced. |
customer (pmipv6-domain-nai) |
This command was introduced. |
customer (pmipv6-lma-mll) |
This command was introduced. |
dscp control-plane (pmipv6-lma) |
This command was introduced. |
dscp control-plane (pmipv6-lma-mag) |
This command was introduced. |
heartbeat (pmipv6-lma) |
This command was introduced. |
heartbeat (pmipv6-lma-mll-cust) |
This command was introduced. |
mobility-service mobile-local-loop |
This command was introduced. |
network (pmipv6-lma-mll-cust) |
This command was introduced. |
pool (pmipv6-mll-cust-network) |
This command was introduced. |
transport (pmipv6-lma-mll-cust) |
This command was introduced. |
clear mpls ldp forwarding |
The ipv6 keyword was added. |
default-vrf implicit-ipv4 disable |
This command was introduced. |
discovery targeted-hello |
The ipv6 keyword was added. |
discovery transport-address |
The ipv6 keyword was added. |
explicit-null |
The ipv6 keyword was added. |
implicit-null-override |
The ipv6 keyword was added. |
neighbor dual-stack transport-connection max-wait |
This command was introduced. |
neighbor dual-stack transport-connection prefer ipv4 for-peers |
This command was introduced. |
neighbor targeted |
The ipv6 keyword was added. |
show mpls ldp bindings |
The ipv6 and afi-all keywords were added. |
show mpls ldp discovery |
The ipv6 and afi-all keywords were added. |
show mpls ldp forwarding |
The ipv6 and afi-all keywords were added. |
show mpls ldp igp sync |
The ipv6 and afi-all keywords were added. |
show mpls ldp interface |
The ipv6 and afi-all keywords were added. |
address-family ipv4/ipv6 label |
The ipv6 keyword was added. |
delegation |
This command was introduced. |
keychain |
This command was introduced. |
mpls traffic-eng pce redelegate |
This command was introduced. |
peer source ipv4 |
This command was introduced. |
precedence |
This command was introduced. |
redelegation-timeout |
This command was introduced. |
redirect default-route nexthop |
This command was introduced. |
redirect nexthop |
This command was introduced. |
set source-address |
This command was introduced. |
show mpls traffic-eng pce lsp-database |
This command was introduced. |
stateful-client delegation |
This command was introduced. |
state-timeout |
This command was introduced. |
bfd address-family ipv4 echo minimum-interval |
This command was introduced. |
bfd echo ipv4 bundle-per-member minimum-interval |
This command was introduced. |
clear bfd dampening |
Added type and interface keywords. |
maximum-paths (IS-IS) |
ECMP support extended from 32 to 64 paths. |
fast-reroute per-prefix ti-lfa |
This command was introduced. |
maximum paths (OSPF) |
ECMP support extended from 32 to 64 paths. |
show ospf database |
show ospf database opaque-area command is extended to display extended Link LSA information. |
show ospf interface |
Command extended to display the status of topology independent fast reroute (TI-FRR) on the interface. |
clear lisp vrf |
This command was introduced. |
decapsulation filter rloc source |
This command was introduced. |
map-server rloc members distribute |
This command was introduced. |
map-server rloc members modify-discovered |
This command was introduced. |
show lisp decapsulation filter |
This command was introduced. |
show lisp session |
This command was introduced. |
show lisp site rloc members |
This command was introduced. |
show lisp site |
This command was introduced. |
port-parameters |
The ics keyword was introduced. |
hw-module high-bandwidth |
This command was introduced. |
hw-module location breakout |
This command was introduced. |
hw-module power saving |
This command was introduced. |
hw-module port-control license |
This command was introduced. |
hw-module port-control non-combo-mode |
This command was introduced. |
show apm psa status |
This command was introduced. |
show apm psm status |
This command was introduced. |
show platform slices |
This command was introduced. |
aaa accounting |
The mobile keyword was added. |
aaa group server tacacs+ |
IPv6 support was introduced on this command. |
server-private (TACACS+) |
IPv6 support was introduced. |
show tacacs |
IPv6 support was introduced on this command. |
tacacs-server host |
IPv6 support is introduced on this command. |
clear netconf-yang agent session |
This command was introduced. |
netconf-yang agent ssh |
This command was introduced. |
show netconf-yang clients |
This command was introduced. |
show netconf-yang statistics |
This command was introduced. |
ssh server netconf |
This command was introduced. |