The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter describes how to configure the thresholds for Performance Monitoring (PM) parameters of a controller and display them.
Depending on the type of a controller, perform any of the following tasks to view the Performance Monitoring (PM) parameters of the controller. Before viewing the PM parameters, a controller should be created.
The following command displays the current performance parameters of an Optics controller for 15-minutes and 24-hour intervals:
show controllers optics R/S/I/P pm current [ 15-min | 24-hour ] optics layerlayer is a number between 1 and 12 depending on the specific hardware whose PM data needs to be displayed.
Here are a few examples:
router# show controllers optics 100/3/0/2 pm current 15-min optics 12
The following commands display the historical performance parameters of an Optics controller for 15-minutes and 24-hour intervals:
show controllers optics R/S/I/P pm history 15-min optics layer bucket bucket-numberbucket-number is a number between 1 and 32.
show controllers optics R/S/I/P pm history 24-hour optics layerHere are a few examples:
router# show controllers optics 100/3/0/2 pm history 15-min optics 12 bucket 4 router# show controllers optics 100/3/0/2 pm history 24-hour optics 5
The following command displays the current performance parameters of an OTU controller for 15-minutes and 24-hour intervals:
show controllers [ OTU4 | OTU2e ] R/S/I/P pm current [ 15-min | 24-hour ] [ fec | otn ]Here is an example:
router# show controllers OTU4 100/3/0/2 pm current 15-min otn
The following commands display the historical performance parameters of an OTU controller for 15-minutes and 24-hour intervals:
show controllers [ OTU4 | OTU2e ] R/S/I/P pm history 15-min [ fec | otn ] bucket-numberbucket-number is a number between 1 and 32.
show controllers [ OTU4 | OTU2e ] R/S/I/P pm history 24-hour [ fec | otn ]Here are a few examples:
router# show controllers OTU4 100/3/0/2 pm history 15-min fec 4 router# show controllers OTU4 100/3/0/2 pm history 24-hour otn
The following command displays the current performance parameters of an ODU controller for 15-minutes and 24-hour intervals:
show controllers [ ODU4 | ODU2e ] R/S/I/P pm current [ 15-min | 24-hour ] otn pathmonitorHere is an example:
router# show controllers ODU4 100/3/0/2 pm current 15-min otn
The following commands display the historical performance parameters of an ODU controller for 15-minutes and 24-hour intervals:
show controllers [ ODU4 | ODU2e ] R/S/I/P pm history 15-min otn pathmonitor bucket-numberbucket-number is a number between 1 and 32.
show controllers [ ODU4 | ODU2e ] R/S/I/P pm history 24-hour otn pathmonitorHere are a few examples:
router# show controllers ODU4 100/3/0/2 pm history 15-min otn pathmonitor 4 router# show controllers ODU4 100/3/0/2 pm history 24-hour otn pathmonitor
The following command displays the current performance parameters of an ethernet controller for 15-minutes and 24-hour intervals:
show controllers [ hundredGigECtrlr | tenGigECtrlr ] R/S/I/P pm current [ 15-min | 24-hour ]Here is an example:
router# show controllers hundredGigECtrlr 100/3/0/2 pm current 15-min
The following commands display the historical performance parameters of an ethernet controller for 15-minutes and 24-hour intervals:
show controllers [ hundredGigECtrlr | tenGigECtrlr ] R/S/I/P pm history 15-min bucket-numberbucket-number is a number between 1 and 32.
show controllers [ hundredGigECtrlr | tenGigECtrlr ] R/S/I/P pm history 24-hourHere are a few examples:
router# show controllers hundredGigECtrlr 100/3/0/2 pm history 15-min 4 router# show controllers hundredGigECtrlr 100/3/0/2 pm history 24-hour
Perform this task to configure the thresholds for Optics Performance Monitoring (PM) parameters.
1.
configure
2.
controller optics
R/S/I/P
3.
pm
[15-min |
24-hour]
optics
[report |
threshold]
{lbc-pc | opr |
opt}
[max-tca |
min-tca]
enable
4.
pm
[15-min |
24-hour]
optics
[report |
threshold]
{lbc -pc| opr |
opt}
[max | min]
value
5.
commit
Perform this task to configure the thresholds for ODU Performance Monitoring (PM) parameters.
1.
configure
2.
controller odu
[HO | LO]
R/S/I/P
3.
perf-mon
[Enable |
Disable]
4.
pm
[15-min |
24-hour]
otn
[report |
threshold]
{rx-bit-err |
rx-crc-err | rx-csf-stats | rx-inv-type | rx-lfd-stats}
enable
5.
pm
[15-min |
24-hour]
otn
pathmonitor
[report |
threshold]
threshold-type
value
6.
commit
Perform this task to configure the thresholds for OTU Performance Monitoring (PM) parameters.
1.
configure
2.
controller otu
[HO | LO]
R/S/I/P
3.
pm
[15-min |
24-hour]
[fec | otn]
[report |
threshold]
[ec-bits |
uc-words]
disable
4.
pm
[15-min |
24-hour]
[fec | otn]
[report |
threshold]
threshold-type
value
5.
commit
Perform this task to configure the thresholds for ethernet Performance Monitoring (PM) parameters.
1.
configure
2.
controller
ethernet
R/S/I/P
3.
pm
{15-min |
24-hour} ether report
threshold-type
enable
4.
pm
{15-min |
24-hour} ether threshold
threshold-type
threshold-value
5.
commit
Feedback