Table Of Contents
Installing ONS 15454 SDH DS3iN-12 Cards
DS3iN-12 Card-Level Indicators
DS3iN-12 Port-Level Indicators
Verify Successful Turn Up of the DS3iN-12 Card
Reset an Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Replace an In-Service Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Obtaining Documentation and Submitting a Service Request
Installing ONS 15454 SDH DS3iN-12 Cards
Product Name: 15454E-DS3IN-12=
This document contains a description of DS3iN-12 card features, installation procedures, removal instructions, and technical specifications. Use this document in conjunction with the Cisco ONS 15454 SDH Installation and Operations Guide and the Cisco ONS 15454 SDH Troubleshooting and Reference Guide when working with DS3iN-12 cards.
This document contains the following sections:
•
"DS3iN-12 Card Specifications" section
•
"Installation Procedures" section
•
"Related Documentation" section
•
"Obtaining Documentation and Submitting a Service Request" section
This document contains the following procedures:
"Installation Procedures" procedure
"Verify Successful Turn Up of the DS3iN-12 Card" procedure
"Removal Procedures" procedure
"Reset an Electrical Card (E1-N-14, DS3iN-12, or E3-12)" procedure
![]()
Note
For information about circuits and card capacities, see the Cisco ONS 15454 SDH Installation and Operations Guide.
DS3iN-12 Card
The twelve-port ONS 15454 SDH DS3iN-12 card provides twelve ITU-T G.703, GR-499, ITU-T G.704 compliant DS-3 ports per card. Each port operates at 44.736 MBits/s (Mbps) over a 75 ohms coaxial cable (with FMEC-E3/DS3). The DS3iN-12 can detect several different errored logic bits within a DS-3 frame. This function lets the ONS 15454 SDH identify a degrading DS-3 facility caused by upstream electronics (DS-3 Framer). In addition, DS3 frame format auto detection and J1 path trace are supported. By monitoring additional overhead in the DS-3 frame, subtle network degradations can be detected. Figure 1 shows the DS3iN-12 faceplate and Figure 2 shows a block diagram of the card.
Figure 1 DS3iN-12 faceplate
![]()
The following list summarizes the DS3iN-12 card features:
•
Provisionable framing format M23, C-bit or unframed
•
Auto recognition and provisioning of incoming framing
•
VC-3 payload mapping as per ITU-T G.707
•
Idle signal ("1100") monitoring as per GR-499
•
P-bit monitoring
•
C-bit parity monitoring
•
X-bit monitoring
•
M-bit monitoring
•
F-bit monitoring
•
Far-end block errors (FEBE) monitoring
•
Far-end alarm and control (FEAC) status and loop code detection
•
Path trace byte support with TIM-P alarm generation
You can install the DS3iN-12 card in any multispeed or high-speed card slot. Each DS3iN-12 port features DSX-level outputs supporting distances up to 450 feet. With FMEC-E3/DS3 the card supports 1.0/2.3 Miniature Coax nonbalanced connectors.
The DS3iN-12 can operate as the protect card in a 1:N (N<5) DS-3 protection group. It has circuitry that allows it to protect up to five working DS3iN-12 cards.
![]()
Note
The lowest level cross-connect is STM-1. Lower level signals, such as E-1, DS-3, or E-3, can be dropped. This may leave part of the bandwidth unused.
DS3iN-12 Card-Level Indicators
The DS3iN-12 card faceplate has three LEDs.
DS3iN-12 Port-Level Indicators
You can find the status of the DS3iN-12 card ports using the LCD screen on the ONS 15454 SDH fan tray assembly. Use the LCD to view the status of any port or card slot; the screen displays the number and severity of alarms for a given port or slot. Refer to Chapter 1, "Alarm Troubleshooting," of the "Cisco ONS 15454 SDH Troubleshooting and Maintenance Guide, R3.3" for a complete description of the alarm messages.
Figure 2 DS3iN-12 block diagram
![]()
DS3iN-12 Card Specifications
•
DS3iN-12 Input
–
Bit Rate: 44.736 MBits/s (Mbps) + 20 ppm
–
Frame Format: ITU-T G.704, ITU-T G.752 / DS-3 ANSI T1.107-1988
–
Line Code: B3ZS
–
Termination: Unbalanced coaxial cable
–
Input Impedance: 75 ohms + 5%
–
Cable Loss: Max 137 m (450 ft.) 734A, RG59, 728A / Max 24 m (79 ft.) RG179
–
AIS: ITU-T G.704-compliant
•
DS3iN-12 Output
–
Bit Rate: 44.736 MBits/s (Mbps) + 20 ppm
–
Frame Format: ITU-T G.704 , ITU-T G.752 / DS-3 ANSI T1.107-1988
–
Line Code: B3ZS
–
Termination: Unbalanced coaxial cable
–
Output Impedance: 75 ohms + 5%
–
AIS: ITU-T G.704-compliant
–
Power Level: -1.8 - +5.7 dBm (The power level is for a signal of all ones and is measured at a center frequency of 22.368 MHz (3 + 1 -kHz) bandwidth.)
–
Pulse Shape: ITU-T G.703, Figure 14 / ANSI T1.102-1988 Figure 8
–
Pulse Amplitude: 0.36 - 0.85 V peak-to-peak
–
Loopback Modes: Terminal and Facility
–
Line Build Out: 0-69 m (0-225 ft.); 69-137 m (226-450 ft.)
•
DS3iN-12 Electrical Interface
–
Connectors: 1.0/2.3 Miniature Coax connectors via FMEC-E3/DS3 card
•
Environmental
–
Overvoltage Protection: as in ITU-T G.703 Annex B
–
Operating Temperature: -5 to +45 degrees Celsius
–
Operating Humidity: 5 - 95%, non-condensing
–
Power Consumption: 26.80 W, 0.56 A (AMPS) @ -48V, 91.5 BTU/Hr.
•
Dimensions
–
Height: 321.3 mm, (12.650 in.)
–
Width: 18.2 mm, (0.716 in.)
–
Depth: 228.6 mm, (9.000 in.)
–
Depth with backplane connector: 235 mm, (9.250 in.)
–
Weight not including clam shell: 0.8 kg (1.9 lbs.)
•
Compliance
ONS15454 SDH cards, when installed in a system, comply with these standards:–
Safety: IEC 60950, EN 60950, UL 60950, CSA C22.2 No. 60950, TS 001, AS/NZS 3260
Installation Procedures
Use this section if you are installing or removing the DS3iN-12 card for the first time. After you become familiar with ONS 15454 SDH card installation and boot up, use this section as a reference.
![]()
CautionAlways use the supplied electrostatic discharge (ESD) wristband when working with an ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower right outside edge of the shelf assembly and ensure the shelf assembly is properly grounded.
![]()
CautionHazardous voltage or energy may be present on the backplane when the system is operating. Use caution when servicing.
Step 1
Open the card ejectors.
Step 2
Carefully insert the card into the guide rails of the desired slot (Figure 3).
Step 3
Push the card into the connector on the back plane by closing the ejectors.
Figure 3 Installing cards in an ONS 15454 SDH
![]()
Card Turn Up
Follow the steps in this section to verify card turn up. If one or more of the Cisco Transport Controller (CTC) software screen conditions according to "Verify Successful Turn Up of the DS3iN-12 Card" section are not met, re-install the card. Replace the unit if the faulty state persists.
Verify Successful Turn Up of the DS3iN-12 Card
Step 1
Verify that power is applied to the shelf assembly.
Step 2
Verify that the DS3iN-12 card has been installed in the correct slot.
Step 3
Verify that the card appears in the correct slot on the CTC software screen.
Step 4
Verify that the card is white on the CTC software screen.
Step 5
Verify that the card is shown in Inventory on the CTC software screen.
Removal Procedures
Use this section if you are installing or removing the DS3iN-12 card for the first time. After you become familiar with ONS 15454 SDH card installation and boot up, use this section as a reference.
![]()
CautionAlways use the supplied electrostatic discharge (ESD) wristband when working with an ONS 15454 SDH. Plug the wristband cable into the ESD jack located on the lower right outside edge of the shelf assembly and ensure the shelf assembly is properly grounded.
![]()
CautionHazardous voltage or energy may be present on the backplane when the system is operating. Use caution when servicing.
![]()
Note
Traffic can be interrupted if you pull an active card from the ONS 15454 SDH. Use caution when replacing cards and verify that only inactive or standby cards are being replaced. If an active card needs to be replaced, follow the procedure to switch the electrical card to standby mode before you pull the card from the node.
Reset an Electrical Card (E1-N-14, DS3iN-12, or E3-12)
![]()
Note
An electrical card reset can cause a linear 1:1 or 1:N protection switch or an MSSPRing protection switch.
The cards should be replaced when the red FAIL LED appears.
Take these precautions before performing an electical card reset to avoid causing a linear 1:1, 1:N or MSSPRing protection switch:
Step 1
Ensure that the working span is active on the local and remote nodes.
Step 2
Ensure that the working span is carrying error-free traffic without SF alarms.
Step 3
Place a lockout on the protection span before initiating an electrical card reset. In an MSSPRing, place a lockout on the East and West cards of the nodes adjacent to the electrical card switch node; for example, to switch the electrical card on Node B, place the lockout on the West card of Node A and on the East card of Node C. No lockout is necessary on Node B. Before the lockout is set, verify that the MSSPRing is not switched. Traffic can be lost if a lockout is set when the MSSPRing is switched, .
<------East [Node A] West------East [Node B] West------East [Node C] West------>
In a 1:1 protection scheme, place a lockout on the protect card and verify that traffic is traveling over the working span before setting the lockout.
Replace an In-Service Electrical Card (E1-N-14, DS3iN-12, or E3-12)
Step 1
Determine which electical card is active. The active card ACT/STBY LED is green. The standby card ACT/STBY LED is yellow.
![]()
Note
You can determine whether the card is in active mode or standby mode by viewing it in the CTC software and positioning the cursor over the card graphic to display the status.
Step 2
Switch the active card to standby:
a.
In the node view, select the Maintenance > E1-N-14, DS3iN-12 and E3-12 tabs.
b.
From the menu, choose Switch.
c.
Click Yes on the Confirm Switch dialog box.
![]()
Note
A minor alarm appears on the manually-switched slot. After the active electrical card goes into standby, the original standby slot becomes active. This causes the former standby card ACT/STBY LED to become green.
Step 3
Pull the new standby card from the ONS 15454 SDH.
Step 4
Insert the replacement card into the empty slot. The replacement card boots up and becomes ready for service after approximately one minute. Release the protection lockout.
Related Documentation
•
DOC-7813038= Cisco ONS 15454 SDH Installation and Operations Guide
•
DOC-7813037= Cisco ONS 15454 SDH Troubleshooting and Reference Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as an RSS feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently supports RSS Version 2.0.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
![]()
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.