Have an account?
  •   Personalized content
  •   Your products and support

Need an account?

Create an account

Cisco ONS SDH TL1 Command Guide, Release 9.2

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco ONS SDH TL1 Command Guide, Release 9.2

Chapter Title

Chapter 6, CLR Commands

Results

Updated:
February 19, 2018

Chapter: Chapter 6, CLR Commands

CLR Commands

This chapter provides CLR (clear) commands for the Cisco ONS 15310-MA SDH, Cisco ONS 15454 SDH, Cisco ONS 15454 M2, and Cisco ONS 15454 M6.

NoteAll commands supported on the Cisco ONS 15454 SDH platform are also supported on Cisco ONS 15454 M2 and Cisco ONS 15454 M6 platforms.

6.1 CLR-CCDB-CFM

(Cisco ONS 15454 SDH) The Clear Continuity Check Message Data Base Connectivity Fault Management (CLR-CCDB-CFM) command clears the continuity check message data base on a given slot.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Equipment

Security

Provisioning

Input Format

CLR-CCDB-CFM:[<TID>]:<AID>:<CTAG>;

Input Example

CLR-CCDB-CFM::SLOT-4:a;

6.2 CLR-COND-SECU

(Cisco ONS 15310-MA SDH and Cisco ONS 15454 SDH) The Clear Security Condition (CLR-COND-SECU) command clears the specified standing condition.

 
Usage Guidelines

In Software Release 6.0 and later, only the INTRUSION-PSWD parameter value is supported.

Category

Security

Security

Superuser

Input Format

CLR-COND-SECU:[<TID>]::<CTAG>[::<SECUALMTYPE>];

Input Example

CLR-COND-SECU:CISCO::123::INTRUSION-PSWD:

Table 6-1 CLR-COND-SECU Command - Parameter Support
Input Parameters
Description
ONS 15454 SDH
ONS 15310-MA SDH

<SECUALMTYPE>

(Optional) Secure alarm type. Defaults to INTRUSION-PSWD. The parameter type is SECUALMTYPE, which is the security alarm type.

Y

Y
  • INTRUSION-PSWD

Condition raised after an invalid password is used during login. Condition is raised only if the password is used a specified number of times.

Y

Y

6.3 CLR-MACTABLE

(Cisco ONS 15310-MA SDH and Cisco ONS 15454 SDH) The CLR-MACTABLE command clears the MAC table that has all the learned MAC addresses.

 
Usage Guidelines

The card should be in Layer2 over DMDM mode to clear the MAC address.

Category

System

Security

Retrieve

Input Format

CLR-MACTABLE:[<TID>]:<AID>:<CTAG>;

Input Example

CLR-MACTABLE::SLOT-2:1;

6.4 CLR-MEPSTATS-CFM

(Cisco ONS 15454 SDH) The Clear Maintenance End Point Statistics Connectivity Fault Management (CLR-MEPSTATS-CFM) command clears the maintenance end point statistics.

 
Usage Guidelines

  • This command is applicable only to GE_XP and 10GE_XP cards.
  • The card should be in Layer2 over DMDM mode.

Category

Equipment

Security

Provisioning

Input Format

CLR-MEPSTATS-CFM:[<TID>]:<AID>:<CTAG>;

Input Example

CLR-MEPSTATS-CFM::SLOT-15:1;

Was this Document Helpful?

FeedbackFeedback

Contact Cisco

Related Support Community Discussions

ABOUT US
CONTACT US
WORK WITH US