- Preface
- Chapter 1: ACT Commands
- Chapter 2: ALW Commands
- Chapter 3: APPLY Commands
- Chapter 4: CANC Commands and Messages
- Chapter 5: CHG Commands
- Chapter 6: CLR Commands
- Chapter 7: CONN Commands
- Chapter 8: COPY Commands
- Chapter 9: DISC Commands
- Chapter 10: DLT Commands
- Chapter 11: ED Commands
- Chapter 12: EX Commands
- Chapter 13: ENT Commands
- Chapter 14: INH Commands
- Chapter 15: INIT Commands
- Chapter 16: OPR Commands
- Chapter 17: REPT Messages
- Chapter 18: RLS Commands
- Chapter 19: RMV Commands
- Chapter 20: RST Commands
- Chapter 21: RTRV Commands
- Chapter 22: SCHED Commands
- Chapter 23: SET Commands
- Chapter 24: SW Commands
- Chapter 25: TST Commands
- Chapter 26: Access Identifiers
- Chapter 27: Conditions
- Chapter 28: Modifiers
Cisco ONS SONET TL1 Command Guide, Release 9.1
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
- Updated:
- February 18, 2018
Chapter: Chapter 20: RST Commands
RST Commands
This chapter provides restore (RST) commands for the Cisco ONS 15310-CL, Cisco ONS 15310-MA, Cisco ONS 15454, and Cisco ONS 15600.
20.1 RST-<MOD2>
(Cisco ONS 15454, 15327, 15600, 15310) The Restore 10GFC, 10GIGE, 40GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, 5GIB, 8GFC, CLNT, D1VIDEO, DS1, DV6000, DVBASI, E1, E3, E4, EC1, ESCON, ETRCLO, ETH, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, ILK, ISCCOMPAT, ISC3PEER2R, ISC3PEER1G, ISC3PEER2G, OC12, OC192, OC3, OC48, OC768, OCH, OMS, OTS, OTU3, POS, STS1, STS12C, STS18C, STS192C, STS24C, STS36C, STS3C, STS48C, STS96C, STS6C, STS9C, T1, T3, VC12, VC3, VT1, or VT2 (RST-<MOD2>) command provisions a facility as In-Service (IS).
Usage Guidelines
See Table 28-1 for supported modifiers by platform.
Note 
This command can only be executed when the port is in the Out of Service and Maintenance (OOS,MT) state.
Category
Ports
Security
Maintenance
Input Format
RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];
Input Example
RST-EC1:CISCO:FAC-1-1:1::::IS,AINS;
Input Parameters
<AID> |
Access identifier from the "ALL" section. |
<PST> |
Primary state. Defaults to IS. The parameter type is PST, which indicates the current overall service condition of an entity. |
• |
In service |
• |
Out of service |
<SST> |
Secondary state. Defaults to AINS. The parameter type is SST, which provides additional information pertaining to PST and PSTQ. |
• |
Automatic In-Service |
• |
Disabled |
• |
Loopback |
• |
Mismatch of Equipment |
• |
Maintenance |
• |
Out of Group |
• |
Software Download |
• |
Unassigned |
• |
Unequipped |
20.2 RST-EQPT
(Cisco ONS 15454, 15327, 15600, 15310) The Restore Equipment (RST-EQPT) command provisions equipment into the IS state from the Maintenance (MT) state.
Usage Guidelines
This command is only applicable to equipment that is in transition from the Maintenance state to the In-Service state.
Category
Equipment
Security
Maintenance
Input Format
RST-EQPT:[<TID>]:<AID>:<CTAG>[::];
Input Example
RST-EQPT:CISCO:SLOT-1:1;
Input Parameters
<AID> |
Access identifier from the "EQPT" section. |
Feedback