Table Of Contents
Cisco Prime Optical 9.5 ML Provisioning Methodology
SNMPv1 and SNMPv2 Trap Destination Setup
Point-to-Point Base Card Configuration
Packet over SONET, Ethernet, and Shared Packet Ring Port Provisioning
Flow Control (Send) Provisioning
Creating or Modifying a Port Channel
Creating or Modifying a Port Channel Member
Deleting a Port Channel Member
IEEE 802.17 RPR Base Card Configuration
Protection Support on ML-Series Cards
Using the Quality of Service Policy Template
Configuring Best-Effort Class Map
Configuring Advanced Class Map
Bandwidth Data Service Provisioning
IP Service-Level Agreement on ML-Series Cards
Enabling or Disabling Rapid Spanning Tree Protocol
Enabling or Disabling Cisco Discovery Protocol
Modifying Layer 2 Service Drops
Enable L2 Service Command Enhancement
Obtaining Documentation and Submitting a Service Request
Cisco Prime Optical 9.5 ML Provisioning Methodology
March 30, 2012
This document describes the methodology that Cisco Prime Optical 9.5 uses to provision ML-series cards.
This document contains the following sections:
•
SNMPv1 and SNMPv2 Trap Destination Setup
•
Packet over SONET, Ethernet, and Shared Packet Ring Port Provisioning
•
IEEE 802.17 RPR Base Card Configuration
•
Protection Support on ML-Series Cards
•
Using the Quality of Service Policy Template
•
IP Service-Level Agreement on ML-Series Cards
•
Enabling or Disabling Rapid Spanning Tree Protocol
•
Enabling or Disabling Cisco Discovery Protocol
•
ML Management Troubleshooting
•
Enable L2 Service Command Enhancement
•
Obtaining Documentation and Submitting a Service Request
Introduction
Cisco Prime Optical (formerly Cisco Transport Manager) is a carrier-class, multitechnology management system that integrates the end-to-end management of traditional transport networks and new carrier packet transport networks. It can help maintain the integrity of existing services, plus deliver interactive, content-based services and high-bandwidth applications.
Cisco Prime Optical manages the entire Cisco optical portfolio, including:
•
Metro core
•
Metro dense wavelength-division multiplexing (DWDM)
•
Metro edge and access products
•
New Carrier Packet Transport (CPT) System products
Prime Optical also serves as a foundation for integration into a larger overall Operations Support System (OSS) environment by providing northbound gateway interfaces to higher-layer management systems.
Prime Optical supports data service provisioning over ML-series cards. Data service provisioning consists of provisioning the Layer 2 topology using optical circuits, and then provisioning the Layer 2 service on top of the Layer 2 topology.
Alarm notification and performance monitoring features on data cards (ML-series cards) are SNMP-based. To allow Prime Optical to support alarm and event notification and performance monitoring on data cards, the SNMP trap forwarding mechanism must be set up on each node of the data card.
This document provides the set of Cisco IOS commands issued by Prime Optical during Layer 2 topology and Layer 2 service provisioning, including provisioning of interface ports for ML data cards. The syntax used for the commands must be respected for services provisioned directly using Cisco IOS so that Prime Optical recognizes the provisioned services.
SNMPv1 and SNMPv2 Trap Destination Setup
For the cards to have full Prime Optical support, the SNMP trap destination must be set up for each node where there is a data card inserted:
•
The NE containing the ML-series card must have a valid SNMP community string. If the SNMP community string is not valid, a resynchronization failure occurs and is logged in the Audit Log.
•
The Cisco IOS startup-config file must contain the snmp-server enable traps command to receive traps from ML-series cards. See Overview for more information.
•
You must force resynchronization on the NE by marking it as Out of Service (OOS), and then back In Service (IS) when you change the trap destination in either Cisco Transport Controller (CTC) or Prime Optical. This operation forces the registration of ML-series cards for traps.
•
You must set up the trap destination based on the SNMP version (SNMPv1 or SNMPv2) and the gateway NE/end NE (GNE/ENE) configuration of the node. Set the trap destination in the NE Explorer window (see Figure 1).
Figure 1 NE Explorer—SNMPv1 and SNMPv2 Trap Destination Setup
![]()
The following table lists the possible SNMP configurations.
When setting up an SNMPv1 or SNMPv2 trap destination:
1.
Delete the GNE and ENE's SNMP trap destinations before performing GNE-ENE role changes. After a GNE-ENE role switch is complete, add the new SNMP trap destinations according to the new GNE-ENE roles.
2.
If the ENE does not contain the GNE's SNMP community string, mark the ENE as Out of Service and then In Service.
3.
Do not use an ONS 15600 as the GNE and an ONS 15454 as the ENE.
4.
The GNE-ENE SNMP community string must be Public.
SNMPv3 Configuration
Prime Optical supports SNMPv3 on CTC-based release 9.5 NEs. (SNMPv3 is not supported on ONS 15305, ONS 15305 CTC, or ONS 15327 NEs.)
As is the case for SNMPv1 and SNMPv2, to support SNMPv3, NEs with ML-series cards must have a valid SNMP configuration to guarantee correct initialization and management of Layer 2 parameters. If the SNMP configuration is invalid, the Audit Log records a resynchronization failure.
Configuring SNMPv3 is more complex than configuring SNMPv1 or SNMPv2, because the following tables must be filled in:
•
SNMPv3 NE User table—The SNMP users for each NE.
•
SNMPv3 User Group table—The grouping of NE SNMP users.
•
SNMPv3 Group View table—A view for any SNMPv3 user grouping.
•
SNMPv3 NE Trap Destination table—The SNMP trap configuration.
•
SNMPv3 NE Notification Filter table—The SNMP trap filtering, if needed.
•
SNMPv3 NE Proxy Forwarder table—The GNE/ENE GET/SET forwarding configuration.
•
SNMPv3 NE Proxy Trap Forwarder table—The GNE/ENE trap forwarding configuration.
For details about configuring SNMPv3, see the section "Managing SNMPv3—CTC-Based Release 9.5 NEs" in Chapter 8, "Managing Security" in the Cisco Prime Optical 9.5 User Guide.
Overview
A Layer 2 topology can be a point-to-point optical circuit; Resilient Packet Ring (RPR) or an IEEE802.17 RPR consisting of a chain of optical circuits; or hub and spoke, consisting of multiple optical circuits connected in a hub-and-spoke fashion. Hub-and-spoke topologies are supported as multiple point-to-point topologies.
For a point-to-point topology, the following card combinations are supported:
•
ML-1000-2/ML-100T-12/ ML-100T-8/ML-100-FX to ML-1000-2/ML-100T-12/ML-100T-8/ML-100-FX card
•
ML-1000-2/ML-100T-12/ ML-100T-8/ML-100-FX to CE-100T-8/CE-1000-4/CE-MR-6/CE-MR-10 card
•
ML-1000-2/ ML-100T-12/ML-100T-8/ML-100-FX to OC-N/STM-N/MRC/CTX card
•
ML-1000-2/ML-100T-12/ML-100T-8/ML-100-FX to G-series card
•
ML-1000-2/ML-100T-12/ML-100T-8/ML-100-FX to E-series card with LEX encapsulation (ONS 15327 NEs only)
When deployed as hub and spoke, the ML-series card can be placed at the spoke locations, with the G-series card providing an extension of the traffic to a Cisco 7600, which forms the hub of the architecture. This arrangement provides a cost-effective way to interface to the Cisco 7600. Alternatively, the ML-series card can be deployed at both the hub and the spoke sites.
When deployed as an RPR or DOT17RPR, all sites contain ML-series cards (ML-1000-2, ML-100T-12, or ML-100T-8). A minimum of two ML-series cards is required to configure an RPR.
You use Prime Optical to provision ML-series cards by opening a Telnet session to each card. Before doing this, provision each ML-series card and create a password configuration that allows you to use Prime Optical to log in. For this purpose, a barebone file is provided on the Prime Optical server disk (Disk 1).
A different file is provided for the following cards:
•
ONS 15310 ML (bareboneCLI_Generic.txt)
•
ONS 15454 ML base microcode (barebone15454CLI_Security.txt)
•
ONS 15454 ML enhanced microcode (barebone15454CLI_Enhanced_Security.txt)
![]()
Note
•
If you want to create a new topology or add a new ML card to an existing RPR topology, you must first download a new barebone file to the ML card, thereby reinitializing the card.
•
You can download a barebone file to multiple ML cards. For details, see the section "Initializing ML-Series Cards" in Chapter 7, "Provisioning Services and Connections" in the Cisco Prime Optical 9.5 User Guide.
![]()
CautionDo not remove any of the information from the barebone file provided by Prime Optical. You can customize the username and password, but do not remove them; the username cannot be blank. Do not add the enable password password command, because Prime Optical cannot interactively enable a password.
Reset the ML-series card after loading the barebone file and wait for 5 minutes before provisioning topologies and services. The login and password are reported in the Control Panel window. You can create other profiles on ML-series cards by using the IOS Users table (available under Administration > CTC-Based NEs > IOS Users Table).
After entering command-line interface (CLI) commands through the Telnet session, Prime Optical issues a write or copy run start command to write the Cisco IOS configuration file to the Timing, Communications and Control (TCC) flash. When the Cisco IOS configuration file is written to the TCC flash (by Prime Optical or by another user), Prime Optical is notified. To verify that Prime Optical has been notified, enter the write command after any CLI change.
Prime Optical provides a GUI wizard to facilitate provisioning of L2 topologies and related L1 circuits. See the section "Provisioning Data Services" in Chapter 7, "Provisioning Services and Connections" in the Cisco Prime Optical 9.5 User Guide. Create an RPR or point-to-point topology involving some of the ML-series cards in the network. Based on the L2 topology circuit type and size that you specify, Prime Optical creates related L1 circuits and installs a base card configuration on each ML-series card in the RPR ring.
The Create Layer 2 Service wizard guides you through the VLAN creation. There is no CLI to create a circuit VLAN. An RPR supports from 1 to 4095 VLANs, and these VLANs are enabled at all times. All that is required is to configure the endpoint to connect a ring VLAN to a port VLAN that is either an Ethernet port or a port channel. Only ML devices are supported on an RPR.
Point-to-point topologies are supported for ML-ML, ML-G1000, ML-OC, and ML-CE cards. Point-to-point topology creation is similar to RPR creation in that based on the L2 topology circuit type and size that you specify, Prime Optical creates related L1 circuits and installs a base card configuration on each ML-series card in the point-to-point topology.
![]()
Note
To remove NEs from an L2 topology, mark the NEs Out of Service, and wait an appropriate amount of time for the L2 topology and corresponding links to be automatically deleted. Once automatic deletion is confirmed, delete the NEs.
CLI Configuration Details
Note the following CLI conventions:
•
Notes are reported within brackets ( [ ] ). For example:
[notes]
•
Optional commands or parameters are reported within brackets ( [ ] ). For example:
[match any]
•
Configurable parameters are reported within left and right angle brackets (< >). For example:
parameter
•
Multiple parameters or commands are enclosed within braces ( { } ) and separated by a vertical bar ( | ). For example:
{parameter_1 | parameter_2 | parameter_3}
Base Card Configuration
The base card configuration is a set of commands entered during the L2 topology creation. The parameters are defined in the Create Layer 2 Topology wizard > Layer 2 Topology Bandwidth pane (see Figure 2).
![]()
Note
Prime Optical supports the setting of a single match cos command for each class-map command. If another match cos command is present on the card, Prime Optical recognizes this additional match cos command incorrectly and displays a null string in the GUI. This additional match cos command must be removed during a modify bandwidth operation.
Figure 2 Create Layer 2 Topology Wizard
![]()
RPR Base Card Configuration
To create an RPR topology, you must apply the base card configuration to all ML-series cards in the RPR. The ring is not functional and is reported as L2 Not Ready until the base card configuration is applied to all cards. You can select an L2 Not Ready RPR in the L2 Topology table and enable the L2 service provisioning by choosing Configuration > Enable L2 Service.
![]()
CautionIf the state is reported as L2 Not Ready, the base card configuration is missing. Choose Configuration > Enable L2 Service to apply the base configuration to the card. This operation affects traffic if the service has already been provisioned on the card.
Prime Optical defines the unique card number within the ring. The actual range is from 1 to 251 in any order. Refer to the NE hardware documentation for the number of ML-series cards allowed per RPR.
cos priority-multicast Class of Service percent Multicast Group %1 [If Multicast Group 1 has been enabled]
cos priority-multicast Class of Service percent Multicast Group %2 [If Multicast Group 2 has been enabled]
class-map match-any SP_MANAGEMENT [If SP Management (%) is greater than 0]
match cos SP Management Class of Service [If SP Management (%) is greater than 0]
class-map match-any AVVID_VOICE_VIDEOmatch cos Low Latency Queue Class of Serviceclass-map match-any AVVID_CONTROL [If AVVID Control (%) is greater than 0]
match cos AVVID Control Class of Service [If AVVID Control (%) is greater than 0]
class-map match-any CIR [If Committed Rate (%) is greater than 0]
match cos Committed Rate Class of Service [If Committed Rate (%) is greater than 0]
class-map match-all BEST_EFFORTmatch anyPolicy-map POLICY_QOS_OUTclass SP_MANAGEMENT [If SP Management (%) is greater than 0]
bandwidth percent SP Management (%) [If SP Management (%) is greater than 0]
class AVVID_VOICE_VIDEOPriority 8 [Fixed values are not configurable]
class AVVID_CONTROLbandwidth percent AVVID Control (%) [If AVVID Control (%) is greater than 0]
class CIR [If Committed Rate (%) is greater than 0]
bandwidth percent Committed Rate (%) [If Committed Rate (%) is greater than 0]
class BEST_EFFORTBandwidth percent Default Best Effort (%)Cos commit CoS CommitVlan dot1q tag nativeL2protocol-tunnel cos 2 [Fixed value]
interface SPR1Spr station-id Card# [The valid range is from 1 to 254; it is not Spr node Card#]
[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
no ip addressno keep alivehold-queue 150 inInterface {FastEthernetN|GigabitEthernetM} [N=0 to 11 and M=0,1]
no ip route-cacheinterface POS0Spr-intf-id 1Service-policy output POLICY_QOS_OUT[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
No ip addressNo ip route-cacheCrc 32interface POS1Spr-intf-id 1Service-policy output POLICY_QOS_OUT[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
No ip addressNo ip route-cacheCrc 32![]()
Note
•
Cisco IOS software supports multiple match cos commands for each class-map command, but Prime Optical supports only one for each.
•
The multicast/broadcast feature applies only to RPR topologies and requires the ONS 15310 R5.0 or ONS 15454 R5.0 or later.
Point-to-Point Base Card Configuration
For a point-to-point topology involved in at least one ML-series card, the other card can be ML, CE, OC, or G1000. The point-to-point base card configuration must be applied only on the ML-series card(s) involved in the topology.
![]()
Note
•
Prime Optical does not enable spanning tree. Therefore, verify that there are no Layer 2 loops formed by bridged connections outside the ML network. Layer 2 loops in a network without spanning tree enabled might cause network instability.
•
If a G1000 card is one endpoint in the point-to-point topology, a Network-to-Network Interface (NNI) connection is assumed. That is, the class of service (CoS) coming into the G1000 is trusted (not overwritten).
cos priority-multicast Class of Service percent Multicast Group %1 [If Multicast Group 1 has been enabled]
cos priority-multicast Class of Service percent Multicast Group %2 [If Multicast Group 2 has been enabled]
class-map match-any SP_MANAGEMENT [If SP Management (%) is greater than 0]
match cos SP Management Class of Service [If SP Management (%) is greater than 0]
class-map match-any AVVID_VOICE_VIDEOmatch cos Low Latency Queue Class of Serviceclass-map match-any AVVID_CONTROL [If AVVID Control (%) is greater than 0]
match cos AVVID Control Class of Service [If AVVID Control (%) is greater than 0]
class-map match-any CIR [If Committed Rate (%) is greater than 0]
match cos Committed Rate Class of Service [If Committed Rate (%) is greater than 0]
class-map match-all BEST_EFFORTmatch anyPolicy-map POLICY_QOS_OUTclass SP_MANAGEMENT [If SP Management (%) is greater than 0]
bandwidth percent SP Management (%) [If SP Management (%) is greater than 0]
class AVVID_VOICE_VIDEOPriority 8 [Fixed values are not configurable]
class AVVID_CONTROLbandwidth percent AVVID Control (%) [If AVVID Control (%) is greater than 0]
class CIR [If Committed Rate (%) is greater than 0]
bandwidth percent Committed Rate (%) [If Committed Rate (%) is greater than 0]
class BEST_EFFORTBandwidth percent Default Best Effort (%)Cos commit CoS CommitVlan dot1q tag nativel2protocol-tunnel cos 2 [Fixed value]
[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
Interface {FastEthernetN|GigabitEthernetM} [N=0 to 11 and M=0,1]
no ip route-cacheinterface POS0service-policy output POLICY_QOS_OUTCrc {16|32} [Crc 16 between ML and E-series; otherwise Crc 32]
[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
No ip addressNo ip route-cacheinterface POS1service-policy output POLICY_QOS_OUTCrc {16|32} [Crc 16 between ML and E-series; otherwise Crc 32]
[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
No ip addressNo ip route-cache![]()
Note
Cisco IOS software supports multiple match cos commands for each class-map command, but Prime Optical supports only one for each.
Packet over SONET, Ethernet, and Shared Packet Ring Port Provisioning
You can use the Create Layer 2 Service wizard, Modify Ports dialog box, Modify VLANs dialog box, Add L2 Service Drops wizard, or Modify L2 Drops wizard to provision the parameters described in the following table.
Table 2 Port Provisioning Parameter Support
Card and Port Types MTU Size Speed Duplex Flow Control (Send) Flow Control (Receive) Enable (No Shutdown)/Disable (Shutdown)ML100T card
Ether
Supported
Supported
Supported
Supported
Not supported
Supported
PoS1
Supported only for PTP
Not supported
Not supported
Not supported
Not supported
Supported
SPR2
Supported only for RPR
Not supported
Not supported
Not supported
Not supported
Not supported
ML1000 (Ether) card
Ether
Supported
Supported only for Auto
Supported only for Auto
Supported
Supported
Supported
PoS
Supported only for PTP
Not supported
Not supported
Not supported
Not supported
Supported
SPR
Supported only for RPR
Not supported
Not supported
Not supported
Not supported
Not supported
ML100FX card
Ether
Not supported
Only 100 is supported
Only Full is supported
Supported
Not supported
Supported
PoS
Supported only for PTP
Not supported
Not supported
Not supported
Not supported
Supported
SPR
Supported only for RPR
Not supported
Not supported
Not supported
Not supported
Not supported
ML100T-8 card
Ether
Not supported
Supported
Supported
Supported
Not supported
Supported
PoS
Not supported
Not supported
Not supported
Not supported
Not supported
Supported
SPR
Only 1500 is supported
Not supported
Not supported
Not supported
Not supported
Not supported
1 PoS = Packet over SONET.
2 SPR = Shared Packet Ring.
Ethernet port provisioning involves configuring the following parameters (see Figure 3):
•
Enable/Disable Ethernet Ports (Administrative State/Link Control)—The ability to enable or disable an Ethernet port at any time is independent of other port provisioning. Prime Optical automatically disables a port when the last connection is removed.
•
MTU Size—Maximum transmission unit (MTU) is the maximum packet size, in bytes, that a particular interface can handle.
•
Speed—Select the speed from the drop-down list, which displays three values: 10, 100, and Auto. For an ML1000 card, Auto is the only supported option.
•
Flow Control (Send)—Select the Flow Control (send) value from the drop-down list, which displays three values: Off, On, and Desired. These values are supported by both Fast Ethernet and Gigabit Ethernet (GE) ports.
PoS port provisioning involves configuring the following parameters (see Figure 3):
•
Enable (No Shutdown)/Disable (Shutdown)—The ability to enable or disable a PoS port at any time is independent of other port provisioning. When the PoS port that is shut down is related to the L2 topology, the topology goes into wrap state. Prime Optical automatically sends an alarm indicating that the L2 topology has entered wrap state.
•
MTU Size—Maximum packet size, in bytes, that a particular interface can handle.
Figure 3 Create Layer 2 Service—Modify Port Properties
![]()
Enable
Interface {FastEthernetN|GigabitEthernetM} [N = 0 to 11 and M = 0,1]
No shutdownDisable
Interface {FastEthernetN|GigabitEthernetM} [N = 0 to 11 and M = 0,1]
shutdownMTU Provisioning
Interface {FastEthernetN|GigabitEthernetM} [N = 0 to 11 and M = 0,1]
mtu MTU [MTU = 64 to 9000]
Speed Provisioning
Interface {FastEthernetN|GigabitEthernetM} [N = 0 to 11 and M = 0,1]
speed Speed [Speed = 10/100/auto]
Duplex Provisioning
Interface {FastEthernetN|GigabitEthernetM} [N = 0 to 11 and M = 0,1]
duplex Duplex [Duplex = half/full/auto]
Flow Control (Send) Provisioning
Interface {FastEthernetN|GigabitEthernetM} [N = 0 to 11 and M = 0,1]
flowcontrol send Flow Control(send) [Flow Control = desired/off/on]
Enable (No Shut)
Interface {POSN} [N = 0 or 1]
No shutdownDisable (Shutdown)
Interface {POSN} [N = 0 or 1]
shutdownMTU Provisioning
Interface {POSN} [N = 0 or 1]
mtu MTU [MTU = 64 to 9000]
Port Channel Provisioning
ML-series cards offer port channel (also known as link aggregation) for Gigabit Ethernet and Fast Ethernet ports.
Port channel is a trunking technology that groups together multiple, full-duplex, IEEE 802.3 Gigabit Ethernet/Fast Ethernet interfaces to provide fault-tolerant, high-speed links between switches, routers, and servers.
Creating or Modifying a Port Channel
interface port-channel channel-ID[no] shutdownmtu MTU-value [The range is from 64 to 9000]
hold-queue HI-queue-value in [The range is from 0 to 4096]
hold-queue HO-queue-value out [The range is from 0 to 4096]
Deleting a Port Channel
no interface port-channel channel-IDCreating or Modifying a Port Channel Member
interface { FastEthernetN | GigabitEthernetM } [N=0 to 11, and M=0,1]
no ip addressno mtuno shutdownchannel-group channel-ID { mode [active | passive] }lacp port-priority port-priority [The range is from 1 to 65535]
Deleting a Port Channel Member
interface { FastEthernetN | GigabitEthernetM } [N=0 to 11, and M=0,1]
no channel-group channel-IDno lacp port-priorityshutdownIEEE 802.17 RPR Base Card Configuration
The base card configuration is a set of commands you enter when creating the Layer 2 topology. Use the Create Layer 2 Topology wizard > Layer 2 Topology Bandwidth pane (see Figure 4) to define parameters for IEEE 802.17 RPR provisioning.
Figure 4 Create Layer 2 Topology Wizard—IEEE 802.17 RPR Topology Creation
![]()
To create an RPR topology, apply the base card configuration to all ML-series cards in the RPR. The topology is reported as L2 Not Ready until the base card configuration is applied to all cards. Select an L2 Not Ready RPR in the L2 Topology table and choose Configuration > Enable L2 Service to enable the L2 service provisioning.
The IEEE 802.17 policy map configuration differs from the policy map configuration in the Cisco RPR. ML-series cards in 802.17 RPR mode support the following traffic classes:
•
Class A (A0/A1)
–
Class A0/A1 traffic is guaranteed low-latency traffic.
–
Class A0 conforms to the reserved rate on the ring.
–
Class A1 does not use the reserved bandwidth.
•
Class B (B-CIR/B-EIR)
–
Traffic that conforms to the B committed information rate (CIR) is not fairness-eligible.
–
Class B EIR traffic is fairness-eligible; it is distinguished from class C traffic at the add node only.
•
Class C traffic is best effort; it is always fairness-eligible.
You can modify the CoS value; the range is from 0 to 7.
Use the following commands to create the IEEE 802.17 RPR:
[Class map configuration]
class-map match-any AVVID_VOICE_VIDEOmatch cos Low Latency Queue Class of Serviceclass-map match-any SP_MANAGEMENTmatch cos SP Management Class of Serviceclass-map match-any CIRmatch cos Committed Rate Class of Serviceclass-map match-any AVVID_CONTROLmatch cos AVVID Control Class of Serviceclass-map match-all BEST_EFFORTmatch any[Policy map configuration]
policy-map POLICY_QOS_OUTclass AVVID_VOICE_VIDEOset rpr-ieee service-class Low Latency Queue [Possible values are a, b, c]
class AVVID_CONTROLset rpr-ieee service-class AVVID Control [Possible values are a, b, c]
class SP_MANAGEMENTset rpr-ieee service-class SP Management [Possible values are a, b, c]
class CIRset rpr-ieee service-class Committed Rate [Possible values are a, b, c]
class BEST_EFFORTset rpr-ieee service-class Default Best Effort [Possible values are a, b, c]
[Absolute bandwidth configuration]
interface rpr-ieee 0rpr-ieee protection pref jumborpr-ieee tx-traffic rate-limit reserved Class A east [Class A range is from 0 to 48 Mb/s]
rpr-ieee tx-traffic rate-limit reserved Class A west [Class A range is from 0 to 48 Mb/s]
rpr-ieee tx-traffic rate-limit high Class A1 east [Class A1 range is from 1 to 48 Mb/s]
rpr-ieee tx-traffic rate-limit high Class A1 west [Class A1 range is from 1 to 48 Mb/s]
rpr-ieee tx-traffic rate-limit medium Class B-CIR east [Class B-CIR range is from 1 to 48 Mb/s]
rpr-ieee tx-traffic rate-limit medium Class B-CIR west [Class B-CIR range is from 1 to 48 Mb/s]
service-policy output POLICY_QOS_OUT![]()
Note
The Protection Frame field is always Jumbo; no other configurable options are supported. The Fairness Mode field is always Aggressive.
In the commands listed above, the upper limit of the range value depends on the circuit size. For example, if x is the maximum range value in megabits per second (Mb/s):
•
FOR_STS1 circuit, x = 48
•
FOR_STS3c_VC4 circuit, x = 149
•
FOR_STS6c_VC4_2c circuit, x = 299
•
FOR_STS9c_VC4_3c circuit, x = 488
•
FOR_STS12c_VC4_4c circuit, x = 598
•
FOR_STS24c_VC4_8c circuit, x = 1196
•
FOR_STS9c_VC4_3c circuit, COMMITTED bandwidth, x = 499
•
FOR_STS12c_VC4_4c circuit, COMMITTED bandwidth, x= 599
•
BW_FOR_STS24c_VC4_8c circuit, COMMITTED bandwidth, x = 1198
Protection Support on ML-Series Cards
You can select IEEE 802.17 RPR ML1000 cards for protection in the Create Layer 2 Topology wizard > Card Selection pane (see Figure 5).
To choose a working card, select any card in the Available Cards list and click Add Working.
To choose a protection card for a working card:
1.
Select the working card.
2.
Select the protection card from the Available Cards list.
3.
Click Add Protect.
![]()
Note
Protection is supported only on ML1000 cards; a working ML1000 card can be protected only by another ML1000 card.
Figure 5 Card Selection—Create Layer 2 Topology Wizard (IEEE 802.17 RPR)
![]()
After you select the protection, commands are issued on the active and protection ML1000 cards, as follows:
•
MAC addresses are configured on both the active and protection cards for the IEEE RPR interface:
–
Active card protection configuration
interface RPR-IEEE0mac-address MAC address of the interface [MAC address range is from 0000.1111.1111 to 0000.9999.9999]
–
Protection card protection configuration
interface RPR-IEEE0mac-address MAC address of the interface [MAC address range is from 0000.1111.1111 to 0000.9999.9999]
•
After the MAC address is configured, the following commands are present on the active and protection cards:
–
Active card protection configuration
interface RPR-IEEE0rpr-ieee ri mode primary peer MAC address of the active card [MAC address range is from 0000.1111.1111 to 0000.9999.9999]
–
Protection card protection configuration
interface RPR-IEEE0rpr-ieee ri mode secondary peer MAC address of the protection card [MAC address range is from 0000.1111.1111 to 0000.9999.9999]
![]()
Note
Any MAC address with the first four digits beginning with 11 (11xx.xxxx.xxxx) is a malformed address and is denied; for example, 1100.2222.3333.
When changing ML1000 GE port states in a scenario with 802.17 RPR redundant interconnect protection configured, the primary ML card remains active if at least one GE port is up.
Conversely, if all GE ports are down, the redundant interconnect protection is triggered and the IEEE 0 interface shuts down on the primary card. When the IEEE 0 interface shuts down, the L2 topology state changes to Steering.
Wrap Status
When a PoS port in a Cisco RPR L2 topology shuts down, Prime Optical raises an alarm to indicate that the L2 topology has entered the corresponding protection state, which is referred to as the wrap state. The status of the Layer 2 topology changes from the original state (Complete or Incomplete) to Complete-Wrapped or Incomplete-Wrapped (see Figure 6).
Figure 6 Layer 2 Topology Table—Complete-Wrapped State
![]()
The Alarm Browser (see Figure 7) displays a wrapped-state alarm.
Figure 7 Alarm Browser—Complete-Wrapped State
![]()
![]()
Note
For alarms and circuits on ML cards that are configured with card mode 802.17 RPR, the ML card ports are referred to as port 0 for RPR-WEST and port 1 for RPR-EAST. This is also true when Prime Optical communicates through the GateWay/CORBA interface.
Steering Status
When an RPR-EAST or RPR-WEST port in a standard 802.17 RPR shuts down, Prime Optical raises an alarm to indicate that the L2 topology has entered the corresponding protection state, which is referred to as the Steering state. The status of the Layer 2 topology changes from the original state (Complete or Incomplete) to Complete-Steering or Incomplete-Steering (see Figure 8).
Figure 8 Layer 2 Topology Table—Complete-Steering State
![]()
The Alarm Browser (see Figure 9) displays an RPR Protection Is Active alarm.
Figure 9 Alarm Browser—Complete-Steering State
![]()
![]()
Note
For Cisco RPRs, the L2 protection state (Wrapped or Steering) is not reflected in the L2 topology state through Prime Optical GateWay/CORBA.
Creating Service Connections
Prime Optical contains an L2 service provisioning wizard to facilitate provisioning of VLANs over a defined L2 topology. You can define each Ethernet port as User-Network Interface (UNI) or Network-Network Interface (NNI). VLANs on an Ethernet port are referred to as port VLANs. VLANs on PoS and SPR ports (and their connected circuits) are referred to as service provider VLANs (or circuit VLANs).
You cannot mix NNI and UNI connections on the same port. Prime Optical supports the following types of service configurations:
•
UNI QinQ Access (user VLAN and protocol transparency)—Cannot be combined with other connection types on the same port.
•
UNI dot1q Access—Select an unused port VLAN from 1 to 4095. It can be combined with untagged connections on the same port. Each port VLAN can be used for only one connection.
•
UNI Untagged Access—Configure as Dot1q Access with port VLAN 1.
•
NNI dot1q Access—Select an unused port VLAN from 1 to 4095. It can be combined with untagged connections on the same port. Each port VLAN can be used for only one connection.
The circuit VLAN range is from 1 to 4095. On an RPR, all valid circuit VLANs can be used; however, due to limited bridge group resources, each ML-series card can access only 255 circuit VLANs. Due to limited card-level bridge group resources, only 255 circuit VLANs can be used on a point-to-point circuit.
![]()
Note
VLAN ID 1 is reserved for untagged VLANs.
For VLAN configurations, the port channel interface is treated as a new, single logical interface, even though it consists of multiple interfaces. The following Cisco IOS commands are sent to the ML card to configure the IEEE 802.1Q encapsulation on the port channel interface. (IEEE 802.1Q encapsulation is the only supported encapsulation type in link aggregation.)
interface port-channel port-channel-ID.VLAN-numberencapsulation dot1Q VLAN-numberbridge-group bridge-group-numberPort channel drops are of NNI type; therefore, no QoS policies are associated to port channel drops, as is true for any other NNI Ethernet drops.
Using the Quality of Service Policy Template
You must configure the following information in the L2 service provisioning and quality of service (QoS) profile wizards:
•
Port (FastEthernetM [FEM] or GigabitEthernetN [GIGEN] with M=0 to 11 and N=0,1)
•
Service connection type (UNI QinQ, UNI dot1Q, UNI untagged, or NNI dot1Q)
•
QoS parameters (selection of the QoS profile name defined in the QoS profile)
Prime Optical assigns an unused bridge group (BG) to the card. The range is from 1 to 255.
The following table lists the configuration information for a best-effort QoS profile. You can select the predefined profile and customize it, or create a new customized profile by using the Advanced option.
The following table lists the configuration information for the committed information rate/peak information rate (CIR/PIR) QoS profile. You can select the predefined profile and customize it, or create a new customized profile by using the Advanced option.
![]()
Note
If you select the CIR/PIR profile and want to modify it, you must configure your own advanced service before you can set the CIR type to Rate_Limited, CIR=PIR, and CIR Burst=PIR Burst.
Prime Optical allows you to define a QoS policy template, starting with the preceding predefined policies and customizing them within the following predefined ranges:
•
CIR_PIR
–
CIR—96,000 to 800,000,000 bits per second (b/s).
–
Max CIR Burst—8000 to 64000 bytes.
–
PIR—96,000 to 800,000,000 b/s. Cannot be less than CIR.
–
Max PIR Burst—8000 to 64000 bytes. Cannot be less than Max CIR Burst.
–
Traffic matching criteria is match-all.
–
Only one policy is allowed.
•
Best_Effort
–
Line Rate—CIR is 96000 b/s and CIR Burst is 8000 bytes.
–
Rate Limited—You configure the CIR and CIR Burst.
–
Traffic matching criteria is match-all.
–
Only one policy is allowed.
You can create your own advanced QoS policy by entering the customized QoS configuration based on the following parameters:
•
Traffic matching criteria.
•
CoS—The range is from 0 to 7.
•
DSCP—The range is from 0 to 63.
•
IP Precedence—The range is from 0 to 7.
•
CoS transmit values for CIR/PIR.
•
Exceed action and violate action and their CoS transmit values.
•
Up to eight QoS classes can be configured.
You must configure the following information in the L2 service provisioning and QoS profile wizards:
•
Port (FastEthernetM [FEM] or GigabitEthernetN [GIGEN] with M=0 to 11 and N=0,1).
•
Service connection type (UNI QinQ, UNI dot1Q, UNI untagged, or NNI dot1Q).
•
QoS parameters (selection of the QoS profile name defined in the QoS profile).
Prime Optical assigns an unused bridge group to the card. The range is from 1 to 255.
![]()
Note
The CLI commands in this section are written for services defined on the RPR topology. For services defined on point-to-point circuits, replace int spr 1 with int pos 0 or int pos 1, depending on which PoS will carry the service. The bridge x protocol command is never issued. Spanning tree is not enabled for RPR or point-to-point circuits. The L2protocol-tunnel all command is expanded to three separate lines when saved by the Cisco IOS router.
For any drop-applied QoS profile, Prime Optical checks the available bandwidth and generates an error message if:
•
totalBW > GE_TOTBW (GE interfaces GE_TOTBW = 1 Gb/s)
•
totalBW > FE_TOTBW (FE interfaces FE_TOTBW = 100 Mb/s)
where the parameter totalBW is calculated as the sum of:
–
New CIR bandwidth reserved for applying the profile
–
CIR bandwidth already reserved on the selected drop by the previously created L2 service
–
Bandwidth reserved for multicast groups during topology creation
For each selected service drop, the configuration is done in three steps:
1.
Class map configuration (not required for NNI-configured ports).
2.
Policy map configuration (through QoS profiles; not required for NNI-configured ports).
3.
Interface configuration (through the Create Layer 2 Service wizard).
The following sections describe the commands for each step.
1. Class Map Configuration
Configuring CIR/PIR Class Map
[Class map configuration for CIRPIR]
Class-map match-all CLASS_BG BG_CIRPIRmatch bridge-group BGConfiguring Best-Effort Class Map
[Class map configuration for BESTEFFORT]
Class-map match-all CLASS_BG BG_BESTEFFORTmatch bridge-group BGConfiguring Advanced Class Map
Figure 10 and Figure 11 show how to use the Create QoS Profile wizard to configure an advanced QoS profile.
Figure 10 Create QoS Profile Wizard—Advanced Class Map Configuration (1 of 2)
![]()
Figure 11 Create QoS Profile Wizard—Advanced Class Map Configuration (2 of 2)
![]()
Enter the following commands to create a QoS profile with advanced OR selection:
[Class map configuration for ADVANCED OR selection]
class-map match-any CLASS_BG BG_ADVANCED_Service Drop Port_N [N number of policies will be configured on the Service Drop Port=0,1 for GigaEthernet and Service Drop Port=0 to 11 for FastEthernet]
[match ip dscp Match DSCP][If Match DSCP has been selected, the valid range is from 0 to 63]
[match ip precedence Match IP Precedence][If Match IP Precedence has been selected, the valid range is from 0 to 7]
[match cos Match CoS][If Match CoS has been selected, the valid range is from 0 to 7]
![]()
Note
A profile with OR conditions can be applied only to a port with a single bridge group configured. Prime Optical excludes the match bridge group statement from the OR class maps and applies class match-any.
2. QoS Profile Configuration
CIR/PIR QoS Profile
Figure 12 is an example of how to create a CIR/PIR QoS profile.
Figure 12 Create QoS Profile Wizard—CIR/PIR
![]()
Enter the following commands for policy map configuration of a CIR/PIR QoS profile:
[Policy map configuration command for the CIR/PIR QoS profile]
Policy-map POLICY_{GIGE|FE}port_INClass CLASS_BG BG_CIRPIR[1. Case Line Rate selection]
Police 96000 8000 conform-action set-cos-transmit 2 exceed-action set-cos-transmit 2[2. Case Rate Limited selection Excess Traffic Discarded]
Police Committed Rate Committed Burst Size conform-action set-cos-transmit 1 exceed-action drop[3. Case Rate Limited selection Excess Traffic Allowed]
Police Committed Rate Committed Burst Size Peak Burst pir Peak Rate conform-action set-cos-transmit 2 exceed-action set-cos-transmit 1 violate-action dropBest-Effort QoS Profile
Figure 13 is an example of how to create a best-effort QoS profile.
Figure 13 Create QoS Profile Wizard—Best Effort
![]()
Enter the following commands to create a best-effort QoS profile:
[Policy map configuration for the BESTEFFORT QoS profile]
Policy-map POLICY_{GIGE|FE}port_INClass CLASS_BG BG_BESTEFFORT[1. Case Line Rate selection]
Police 96000 8000 conform-action set-cos-transmit 0 exceed-action set-cos-transmit 0[2. Case Rate Limited selection]
Police Max Rate Max Burst conform-action set-cos-transmit 0 exceed-action dropAdvanced QoS Profile
Figure 14 is an example of how to create an advanced QoS profile.
Figure 14 Create QoS Profile Wizard—Advanced
![]()
[Policy map configuration for the ADVANCED QoS profile]
Policy-map POLICY_{GIGE|FE}port_INClass CLASS_BG BG_ADVANCED_Service Drop Port_N[N number of policies will be configured on the Service Drop Port = 0,1 for Gigabit Ethernet and Service Drop Port = 0 to 11 for Fast Ethernet.]
police Committed Rate Committed Burst Size [Peak Rate pir Peak Burst] conform-action {transmit|set-cos-transmit Committed CoS Marking Value} [exceed-action {drop|set-cos-transmit Excess CoS Marking Value}][violate-action {drop|set-cos-transmit Violation CoS Marking Value}][[Peak Rate pir Peak Burst] is applied only if Excess Traffic is Allowed.] [exceed-action drop is applied only if Excess Traffic is Discarded.]
[Trust option is never selectable for Excess Traffic or Violation tab. Mark CoS option is always used when the Excess or Violations is Allowed.]
[violation-action drop is applied only if Excess Traffic is Allowed and Violate Traffic is Discarded.]
Bandwidth Data Service Provisioning
In the Control Panel > NE Service > CTC-Based SONET NEs or CTC-Based SDH NEs, select the Enable Bandwidth DSP check box to enable the bandwidth data service provisioning check during L2 service provisioning. The bandwidth utilization report shows available and used bandwidth for each L2 topology. Use this report during L2 service provisioning to verify whether the requested CIR is available on the topology. An error is returned if there is not enough bandwidth available for a drop port.
3. Interface Configuration
Adding UNI QinQ Access
Any port with mode dot1q-tunnel is a UNI QinQ access connection. Figure 15 and Figure 16 show how to add UNI QinQ access using the Create Layer 2 Service wizard.
Figure 15 Create Layer 2 Service Wizard—Adding UNI QinQ Access
![]()
Figure 16 Create Layer 2 Service Wizard—Configuring Service Drops
![]()
Enter the following commands to configure an interface:
[Interface configuration]
Interface {GigabitEthernetport|FastEthernetport}Description QoS profile name[Prime Optical issues the L2protocol-tunnel all command and the result is the following set of commands]
l2protocol-tunnel cdpl2protocol-tunnel stpl2protocol-tunnel vtpno cdp enableMode dot1q-tunnelBridge-group BGService-policy input POLICY_{GIGE|FE}port_INService-policy output POLICY_QOS_OUT[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
Bridge-group BG spanning-disableInterface SPR1.Service Provider VLANEncapsulation dot1q Service Provider VLANBridge-group BG[The following commands are not issued by Prime Optical; rather, these are default ML
settings]
Bridge-group BG spanning-disableRemoving UNI QinQ Access
Enter the following commands to delete a UNI QinQ drop:
[Note the reverse order of commands]
Interface SPR1.Service Provider VLANNo Bridge-group BGNo Encap dot1q Service Provider VLANNo Interface SPR1.Service Provider VLAN [Ignore the warning message]
Interface {GigabitEthernetport|FastEthernetport}No Bridge-group BGNo Mode dot1q-tunnelNo L2protocol-tunnel allNo descriptionNo class-map CLASS_BG BG_{CIRPIR|BESTEFFORT|ADVANCED_Service Drop Port_N}[For Advanced QoS, remove all of the N number of class maps]
[When removing the last connection from a port]
No Policy-map POLICY_{GIGE|FE}port_INNo Service-policy output POLICY_QOS_OUTAdding UNI dot1Q Access
Figure 17 is an example of the Create Layer 2 Service wizard for adding UNI dot1Q access.
Figure 17 Create Layer 2 Service Wizard—Adding UNI dot1Q Access
![]()
The port is recognized as UNI if you enter the service-policy input command on the port interface; otherwise, the port is recognized as NNI. Every subinterface is a dot1q connection. The classification of UNI versus NNI is based on the port-level parsing. A connection is untagged if you enter the encap dot1q 1 command. The multiple class map and QoS policy configurations for advanced QoS are similar to the QinQ Access example shown in Figure 17.
Enter the following commands to create a UNI Dot1q:
[Interface configuration]
[First time only; first dot1q on this UNI port]
Interface {GigabitEthernetport|FastEthernetport}Service-policy input POLICY_{GIGE|FE}port_INService-policy output POLICY_QOS_OUTInterface {FastEthernetport|GigabitEthernetport}.Port VLANDescription QoS profile nameEncapsulation dot1q Port VLANBridge-group BG[In the following command executed by Prime Optical, RSTP is not enabled]
Bridge-group BG spanning-disableInterface SPR1.Service Provider VLANEncapsulation dot1q Service Provider VLANBridge-group BG[In the following command executed by Prime Optical, RSTP is not enabled]
Bridge-group BG spanning-disableRemoving UNI dot1Q Access
Enter the following commands to delete a UNI Dot1q:
[Note the reverse order of commands]
Interface SPR1.Service Provider VLANNo Bridge-group BGNo Encap dot1q Service Provider VLANNo Interface SPR1.Service Provider VLAN [Ignore the warning message]
Interface port.Port VLANNo Bridge-group BGNo Encap dot1q Port VLANNo descriptionNo Interface port.Port VLAN [Ignore the warning message]
Policy-map POLICY_{GIGE|FE}port_INNo Class BG BG_{CIRPIR|BESTEFFORT|ADVANCED_Service Drop Port_N}[For Advanced QoS, remove all of the N number of class maps]
No class-map CLASS_BG BG_{CIRPIR|BESTEFFORT|ADVANCED_Service Drop Port_N}[For Advanced QoS, remove all of the N number of class maps]
[When removing the last connection from a port]
No Policy-map POLICY_{GIGE|FE}port_INNo Service-policy output POLICY_QOS_OUTAdding UNI Untagged Access
UNI untagged access is similar to UNI dot1Q access with port VLAN ID = 1.
Adding NNI dot1Q Access
Enter the following commands to create an NNI Dot1Q:
[Interface configuration]
[First time only; first connection on this port]
Interface {FastEthernetport|GigabitEthernetport}Service-policy output POLICY_QOS_OUTInterface {FastEthernetport|GigabitEthernetport}.Port VLANEncap dot1q Port VLANBridge-group BGInterface spr 1.Server Provider VLANEncap dot1q Server Provider VLANBridge-group BGRemoving NNI dot1Q Access
Enter the following commands to delete an NNI Dot1Q:
[Note the reverse order of commands]
Interface spr 1.Server Provider VLANNo Bridge-group BGNo Encap dot1q Server Provider VLANNo Interface spr 1.Circuit VLAN [Ignore the warning message]
Interface port.Port VLANNo Bridge-group BGNo Encap dot1q Port VLANNo Interface {FastEthernetport|GigabitEthernetport}.Port VLAN [Ignore the warning message]
[When removing the last connection from a port]
No Service-policy output POLICY_QOS_OUTIP Service-Level Agreement on ML-Series Cards
IP SLA is an application embedded in Cisco IOS, which enables you to monitor service-level agreements (SLAs) on IP networks. Service levels are measured by downtime, bandwidth, latency, jitter, packet loss, and so on. Using the IP SLA application, you can verify service guarantees, increase network reliability by validating network performance, proactively identify network issues, and increase return on investment (ROI) by easing the deployment of new IP services.
IP SLA can be configured only on ML-series cards participating in point-to-point and RPR L2 topologies.
![]()
Note
IP SLA is not supported on 802.17 RPR.
Three steps are required to enable IP SLA features:
1. Create a Managed VLAN
Create a managed VLAN by selecting IP SLA Managed VLAN in the Layer 2 Service wizard (see Figure 18) to create a managed VLAN. You can create managed VLANs only on already existing point-to-point and RPR L2 topologies.
Figure 18 Layer 2 Service Wizard—Managed VLAN-Enable
![]()
In the Service Drops Configuration pane > IP SLA tab (see Figure 19), IP addresses are automatically generated and assigned to all of the service drop points that Prime Optical manages.
Figure 19 Create Layer 2 Service Wizard—IP SLA
![]()
For information about commands that are issued based on the provisioning in the Service Drops and Port Attributes tabs, see Creating Service Connections.
The following commands are issued when you assign an IP address to the service drop and specify the routing protocol.
IP Address Assignment
ip address IP Address Subnet [IP Address range is from 192.168.0.1 to 192.168.255.255. Subnet value is 255.255.0.0.]
Routing Protocol Assignment
bridge bridgegroupno route ip [Unique bridgegroupno is created by Prime Optical. The range is from 1 to 255.]
2. Create an IP SLA Session
Create an IP SLA session between a pair of ML-series cards, or between an ML-series card and non-ML IP addresses. Select either Cisco-supported service points or external-destination IP addresses.
You can use the VLAN table (when a managed VLAN is selected) with the Create IP SLA wizard (see Figure 20) to provision the IP SLA session.
Figure 20 Create IP SLA Wizard
![]()
![]()
Note
Prime Optical does not validate nonsupported external destination addresses. Ensure that the external destination is valid and that it responds to a ping command.
Prime Optical automatically generates the IP SLA ID. The service drop points are displayed in the source and destination points, and you can pick up any drop point. You can specify a non-Prime Optical supported destination. IP SLA can be enabled during or after creation of the IP SLA session.
![]()
Note
The source and destination port cannot be the same.
Two types of probes are supported: jitter and echo. Based on the probe type you select in the Create IP SLA wizard, you must enter additional information.
•
If you select the jitter probe, enter a value for the following attributes (see Figure 21):
–
Destination Port—1 through 65535
–
NoOfPackets—1 through 60000
–
Interval—1 through 60000 (in milliseconds)
–
TOS (Type of Service)—0 through 255
–
Operation Frequency—1 through 604800 (seconds)
Figure 21 Create IP SLA Wizard—Jitter Probe
![]()
Prime Optical issues the following commands on the source:
rtr IPSLA ID [IPSLA ID number range is from 1 to 2147483647]
type jitter dest-ipaddr Destination IP Address dest-port Destination Port num-packets Number of Packets interval Intervaltos TOS frequency Operation FrequencyThe RTR responder is then configured on the destination for jitter operation. For a Prime Optical-supported destination (any ML-series cards), Prime Optical issues the following command on the destination:
rtr (responder)![]()
Note
For the IP SLA session to work correctly on a destination that Prime Optical does not support, you must enter the rtr (responder) command on the destination.
•
If you select the echo probe, no additional information is required and Prime Optical issues the following commands on the source:
rtr IPSLA ID [IP SLA number range is from 1 to 2147483647]
type echo protocol ipIcmpEcho Destination IP Address source-ipaddr Source IP Address[Destination IP Address could be a Prime Optical-managed ML card or an external device. Source IP Address is always a Prime Optical-managed ML card.]
![]()
Note
Performance monitoring is disabled for the IP SLA echo operation. If you select an echo row in the IP SLA performance monitoring (PM) table, the Performance menu is disabled.
3. Manage the IP SLA Session
To begin collecting, enable the IP SLA session. The operation ends after 3600 seconds, but you can restart it from the Restart IP SLA menu.
Use the IP SLA table (see Figure 22) to enable, restart, and delete IP SLA.
Figure 22 IP SLA Table
![]()
Use the following commands to enable, restart, and delete IP SLA:
Enable IP SLA
rtr schedule IPSLA ID start-time now [IP SLA Number range is from 1 to 2147483647]
Restart IP SLA
rtr restart IPSLA ID [IP SLA Number range is from 1 to 2147483647]
Delete IP SLA
No rtr IPSLA ID [IP SLA Number range is from 1 to 2147483647]
![]()
Note
The MIB uses SNMP to retrieve PM statistics on IP SLA.
The following table lists the PM data retrieved on IP SLA for jitter. To view the statistics, choose IP SLA Table > Performance (see Figure 22).
Enabling or Disabling Rapid Spanning Tree Protocol
You can enable Rapid Spanning Tree Protocol (RSTP) on UNI dot1Q, UNI Untagged, and NNI dot1Q ports by selecting the RSTP for the selected drop port and then checking the RSTP Enable check box (see Figure 23). To disable RSTP, select the RSTP for the selected drop port and uncheck the RSTP Enable check box.
![]()
Note
RSTP can be enabled only on a drop where UNI/NNI dot1Q is selected and only on a subinterface (that is, UNI dot1Q drop) where no other QinQ drops were created for the same interface.
Figure 23 Create Layer 2 Service Wizard—RSTP Enable
![]()
Click Next to configure QoS parameters as required (see Figure 24).
Figure 24 Create Layer 2 Service Wizard—QoS Parameters
![]()
If the RSTP Enable check box is checked, Prime Optical issues the following command specified for adding a drop:
[Configure RSTP; this command is issued once for VLANs]
bridge BG protocol rstp[Enable RSTP on the selected drop]
Interface {FastEthernetport|GigabitEthernetport}.Port VLANBridge-group BGThe following command is issued when you disable RSTP from a drop:
[Disable RSTP on the selected drop]
Interface {FastEthernetport|GigabitEthernetport}.Port VLANBridge-group BGBridge-group BG spanning-disabled [Disable RSTP on the selected drop]
![]()
Note
•
Enabling or disabling RSTP on a port basis is not valid if you configured a bridge group to the main Ethernet interface. By default, the CLI disables the dot1Q drop in the card.
•
If only the RSTP Enable check box is checked, the Spanning Tree Protocol remains disabled on the VLAN service drops.
Enabling or Disabling Cisco Discovery Protocol
You can enable or disable Cisco Discovery Protocol (CDP) when:
•
Modifying Layer 2 Service Drops
Creating a Layer 2 Service
In the Create Layer 2 Service wizard > Port Attributes tab > CDP drop-down list (see Figure 25), choose enable or disable to enable or disable CDP.
Figure 25 Create Layer 2 Service Wizard—Enable or Disable CDP
![]()
Modifying Layer 2 Service Drops
In the Modify Layer 2 Service Drops wizard > Port Attributes tab > CDP drop-down list (see Figure 26), choose enable or disable to enable or disable CDP. Click Apply.
Figure 26 Modify Layer 2 Service Drops Wizard—Enable or Disable CDP
![]()
Modifying Drops
Step 1
In the Domain Explorer window, choose Configuration > CTC-Based SONET NEs or CTC-Based SDH NEs > L2 Topology Table.
Step 2
In the Layer 2 Topology table, choose Configuration > Show L2 Services.
Step 3
In the L2 Services table, select a service; then, choose Configuration > Show Drops. The L2 Service Drop Ports table opens, listing all the drops in the selected service.
Figure 27 Layer 2 Service Drop Ports Table
![]()
Step 4
Choose Configuration > Modify Ports. The Modify Ports dialog box opens (see Figure 28).
Figure 28 Modify Ports
![]()
Step 5
In the Enable/Disable Port > CDP drop-down list, choose enable or disable to enable or disable CDP.
Prime Optical issues the following command when you enable CDP on a selected drop:
Interface {FastEthernetport|GigabitEthernetport}.Port-VLANcdp enablePrime Optical issues the following command when you disable CDP on a selected drop:
Interface {FastEthernetport|GigabitEthernetport}.Port-VLANno cdp enableML Management Troubleshooting
If a problem arises during the initial synchronization, you can resynchronize the Layer 2 topology by choosing Configuration > Resync L2 Topology in the Layer 2 Topology table (see Figure 29).
![]()
Note
This feature only restarts the L2 topology resynchronization state. It does not forcefully apply any configuration on the ML-series card to complete the synchronization of the L2 topology.
Alternative methods of resynchronization are:
•
Mark the NEs participating in the L2 topology as Out of Service, and then In Service.
•
Restart the NE service.
Although effective, these methods cause a time lag that affects other functions, such as inventory collection and circuit discovery.
Figure 29 Layer 2 Topology Table—Resynchronize L2 Topology
![]()
ML Version Up
When you upgrade a node, you can choose to upgrade the software running on the ML-series cards at a later time. The Version Up feature allows you to delay upgrading the ML-series card, and to choose which ML-series card to upgrade to the new version. By using this feature, you can also view the state of the node with respect to the upgrade, which can be:
•
Complete upgrade—All the non-ML and ML-series cards have been upgraded to the new software release.
•
Partial upgrade—The ML-series cards have not all been upgraded to the new software release.
To enable the Version Up feature, complete the following steps:
1.
Set the value for the parameter NODE.Software.AllowDelayedUpgrade in the Value column under the NE Defaults tab to TRUE (see Figure 30).
Figure 30 NE Explorer—NE Defaults Tab
![]()
2.
Activate the NE software. Use the Bulk Software Activation wizard to activate the NE software (see Figure 31). For specific instructions, see the section "Scheduling Bulk Software Activation" in Chapter 4, "Maintaining an Efficient Network" in the Cisco Prime Optical 9.5 User Guide.
Figure 31 Bulk Software Activation Wizard
![]()
During NE software activation, you are asked if you want to delay the software upgrade on the ML-series cards (see Figure 32). For specific instructions, see the section "Delaying Software Activation on the ML-Series Cards" in Chapter 4, "Maintaining an Efficient Network" in the Cisco Prime Optical 9.5 User Guide.
Figure 32 Software Activation
![]()
![]()
Note
•
While ML-series cards on the NE are waiting to be upgraded, all provisioning operations and software downloads on the NE are disallowed.
•
You can upgrade the NE fully to the latest version by resetting all the ML-series cards to this version.
After a successful partial software activation on the NE, the NE Software table (see Figure 33) displays True in the Partial Upgrade column, which indicates that the activation is pending for ML-series cards.
3.
Upgrade the ML-series cards to the current version by resetting them on the NE in either of the following ways:
–
Select multiple ML-series cards and choose Edit > Reset ML Cards in the NE Software table. For specific instructions, see the section "Activating a New NE Software Version on One or More ML-Series Card(s)" in Chapter 4, "Maintaining an Efficient Network" in the Cisco Prime Optical 9.5 User Guide.
–
For individual ML-series cards, use the NE Explorer.
The Partial Upgrade column in the NE Software table displays FALSE when all ML-series cards are upgraded to the current version.
Figure 33 NE Software Table—Reset ML Cards
![]()
Enable L2 Service Command Enhancement
The enable L2 service command has been enhanced. (See the section "Enabling Layer 2 Services" in Chapter 7, "Provisioning Services and Connections" in the Cisco Prime Optical 9.5 User Guide.)
The enable L2 service command is used only when the resynchronization status of the topology is L2 Service Not Ready, and its main purpose is to change the Layer 2 topology into a resynchronization status of Complete so that a VLAN can be created.
Instead of commanding the default base card configuration on all ML-series cards in the topology to be downloaded, this command downloads a customized base card configuration on only the selected Layer 2 topology ML-series cards that do not have the customized configuration and are in a synchronized configuration state (barebone file downloaded).
This command applies to point-to-point, Cisco RPR, and 802.17 RPR Layer 2 topologies.
Related Documentation
![]()
Note
You can access the most current Prime Optical documentation online at http://www.cisco.com/en/US/products/ps11670/tsd_products_support_series_home.html.
The Prime Optical documentation set comprises the following guides:
•
Release Notes for Cisco Prime Optical 9.5—Describes the caveats for Prime Optical.
•
Cisco Prime Optical 9.5 Installation Guide—Explains how to install Prime Optical and how to upgrade from previous releases.
•
Cisco Prime Optical 9.5 User Guide—Describes how to use the Prime Optical software, which consists of user applications and tools for network discovery, network configuration, connection management, fault management, system administration, and security management.
•
Cisco Prime Optical 9.5 GateWay/CORBA User Guide and Programmer Manual—Describes the GateWay/CORBA northbound interface product that is available for Prime Optical. This document serves as a reference for developers of OSS applications that work with the GateWay/CORBA interface.
•
Cisco Prime Optical 9.5 Database Schema—Describes the database schema that Prime Optical uses to store information in a Structured Query Language (SQL) database such as the Oracle database. The document is designed for users who need to create their own reports without using Prime Optical.
•
Cisco Prime Optical 9.5 High Availability Installation Guide—Explains how to install Prime Optical in a high availability (HA) environment.
![]()
Note
To obtain the Cisco Prime Optical 9.5 High Availability Installation Guide, contact your Cisco account representative.
•
Cisco Prime Optical 9.5 ML Provisioning Methodology—This document.
•
Cisco Prime Optical 9.5 Basic External Authentication—Describes how Prime Optical supports basic external authentication.
•
Migration Matrix for Service Pack Releases—Describes the migration matrix for service pack releases.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.
This document is to be used in conjunction with the documents listed in the "Related Documentation" section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
© 1999-2012 Cisco Systems, Inc. All rights reserved.