Installing Cisco Prime Optical 9.3 GateWay/CORBA
The Cisco Prime Optical 9.3 GateWay/CORBA option is a CORBA-based interface that provides higher-layer management systems with information for all Prime Optical-supported NEs. This chapter describes how to install Prime Optical GateWay/CORBA after installing the Prime Optical 9.3 server.
A reliable network connection is required when carrying out an installation on a remote workstation.
Note For more information about CORBA support, including how to configure Prime Optical GateWay/CORBA, see the Cisco Prime Optical 9.3 GateWay/CORBA User Guide and Programmer Manual.
This chapter contains the following sections:
•Installing Prime Optical GateWay/CORBA
•Re-enabling Prime Optical GateWay/CORBA After Reinstalling the Prime Optical Database
4.1 Installing Prime Optical GateWay/CORBA
Note•You must install Prime Optical GateWay/CORBA on the same workstation as the Prime Optical server. During the Prime Optical GateWay/CORBA installation, you do not need to shut down the Prime Optical server.
•The Prime Optical database must be up and running before you install Prime Optical GateWay/CORBA.
Step 1 (For Solaris operating systems only; not applicable to Linux) Log into the Prime Optical server workstation as the root user. The C shell (csh) is recommended. To start the C shell, enter the following command:
Step 2 Enter the following command to set the DISPLAY variable:
setenv DISPLAY hostname-or-IP-address:0.0
Step 3 Enter the following command to verify that the display is set correctly:
In the output, you should see:
Step 4 If you are using an xterm window or a remote host, enter the following command to enable the xterm connection from the clients:
Step 5 Before you install Prime Optical GateWay/CORBA, Oracle must be running. Enter the following command on the Prime Optical database server to determine whether Oracle processes are running:
The command output is similar to the following:
oracle 20557 1 0 Sep 25 ? 0:00 oracleCTM (LOCAL=NO)
oracle 1216 1 0 Sep 17 ? 0:42 ora_q001_CTM
oracle 20599 1 0 Sep 25 ? 0:05 oracleCTM (LOCAL=NO)
oracle 770 1 0 Sep 17 ? 24:11 ora_pmon_CTM
oracle 20607 1 0 Sep 25 ? 0:05 oracleCTM (LOCAL=NO)
oracle 790 1 0 Sep 17 ? 9:34 ora_lgwr_CTM
oracle 773 1 0 Sep 17 ? 1:45 ora_psp0_CTM
oracle 779 1 0 Sep 17 ? 2:02 ora_mman_CTM
oracle 784 1 0 Sep 17 ? 3:55 ora_dbw0_CTM
oracle 803 1 0 Sep 17 ? 27:25 ora_ckpt_CTM
oracle 808 1 0 Sep 17 ? 2:29 ora_smon_CTM
oracle 812 1 0 Sep 17 ? 0:02 ora_reco_CTM
oracle 818 1 0 Sep 17 ? 39:32 ora_cjq0_CTM
oracle 838 1 0 Sep 17 ? 66:10 ora_mmnl_CTM
oracle 832 1 0 Sep 17 ? 10:27 ora_mmon_CTM
oracle 1181 1 0 Sep 17 ? 0:50 ora_qmnc_CTM
oracle 1198 1 0 Sep 17 ? 0:00 ora_q000_CTM
oracle 20589 1 0 Sep 25 ? 0:05 oracleCTM (LOCAL=NO)
oracle 20749 1 0 Sep 25 ? 0:00 oracleCTM (LOCAL=NO)
oracle 7316 1 0 09:13:02 ? 0:00
/oracle/product/11.2.0/bin/tnslsnr LISTENER -inherit
oracle 20741 1 0 Sep 25 ? 0:00 oracleCTM (LOCAL=NO)
Step 6 Depending on your configuration, insert one of the following DVDs into the DVD drive:
•Cisco Prime Optical Server installation DVD—Linux
•Cisco Prime Optical Server installation DVD—Solaris
Step 7 Enter the following commands:
The installation begins. Wait for up to 90 seconds while the following message appears:
Please wait, Cisco Prime Optical Server Release 9.3 is being configured for your system.
This may take a moment...
Step 8 At the Introduction screen, click Next.
Step 9 At the License Agreement screen, read the license agreement and click the I accept the terms of the license agreement radio button. Click Next.
Step 10 At the Installation Options screen, check Cisco Prime Optical GateWay/CORBA; then, click Next.
Step 11 The Pre-Installation Summary screen shows the items that will be installed. Click Install.
Step 12 The Install Complete screen summarizes the results of the installation. Click Done.
4.2 Re-enabling Prime Optical GateWay/CORBA After Reinstalling the Prime Optical Database
If you reinstall the Prime Optical database on the workstation where Prime Optical GateWay/CORBA is installed, the Prime Optical GateWay/CORBA node will be disabled in the Control Panel window.
To re-enable the Prime Optical GateWay/CORBA node in the Control Panel, run the update_config_for_gwcorba.sh script located in the /opt/CiscoTransportManagerServer/bin directory.