The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This document discusses how consolidated packages and software subpackages (individual and optional) are run and managed on the Cisco cBR Series Converged Broadband Router. It contains the following sections:
Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.
The Cisco cBR Series Converged Broadband Router can be configured to run using individual subpackages and optional subpackages.
When the router is configured to run using individual and optional subpackages:
Each individual subpackage within a consolidated package is extracted onto the router as its own file.
Additionally, any optional subpackages must be separately downloaded and stored in the same directory with the provisioning file and the other individual subpackages that have been extracted.
The router then runs by accessing each file as needed for operational purposes. All individual and optional subpackage files must be stored in the same directory on the router for the router to run properly using individual subpackages.
When the router runs using the individual and optional subpackages, the router needs to be configured to boot using the provisioning file that was included in the consolidated package with the individual subpackage files. This provisioning file must also be in the same directory as the individual and optional subpackage files. The router boots faster when configured to run using individual and optional subpackages than it does when configured to run using a consolidated package.
A Cisco cBR Series Router cannot be configured to run individual and optional subpackages stored on a TFTP or any other network server. To use this method of running the router, copy the individual and optional subpackages along with the provisioning file onto the bootflash: file system.
The Cisco cBR Series Converged Broadband Router can also be configured to run using a consolidated package.
Note | Booting the router from a consolidated package is not supported for installation of optional subpackages. |
When the router is configured to run using a consolidated package, the entire consolidated package file is copied onto the router or accessed by the router via TFTP or another network transport method. The router runs using the consolidated package file.
A router configured to run using a consolidated package is booted by booting the consolidated package file. Because this file is large, the boot process for routers running using the consolidated package is slower than the boot process for routers running individual subpackages.
A router configured to run using a consolidated package does have some advantages over a router configured to run individual subpackages. First, a consolidated package can be booted and utilized using TFTP or another network transport method. Secondly, configuring the router to use the one consolidated package file is easier than managing several individual subpackage files. Running the router using a consolidated package may be the right method of running the router in certain networking environments.
The consolidated package should be stored on bootflash:, usb[0-1]:, or a remote file system when this method is used to run the router.
The advantages of running your router using individual subpackages include:
The router boots fastest when booted using the individual subpackage boot approach.
Individual subpackages can be upgraded instead of the complete consolidated image.
The advantages of running your router using a consolidated package include:
Simplified installation—Only one software file needs to be managed instead of several separate images.
Storage—A consolidated package, unlike individual subpackages, can be used to run the router while being stored in bootflash:, on a USB Flash disk, or on a network server. A consolidated package can be booted and utilized using TFTP or another network transport method, while the individual subpackage method requires the individual subpackage files to be copied into the bootflash: file directory on the router.
Software files can be managed on the Cisco cBR Series Converged Broadband Router using the following distinct command sets.
The request platform software package command is part of the larger request platform command set being introduced on the Cisco cBR Series Converged Broadband Router.
The request platform software package command, which can be used to upgrade individual subpackages and a complete consolidated package, is used to upgrade software on the Cisco cBR Series Converged Broadband Router. Notably, the request platform software package command is the recommended way of performing an individual subpackage upgrade, and also provides the only method of no-downtime upgrades of individual subpackages on the router when the router is running individual subpackages.
The request platform software package command requires that the destination device or process be specified in the command line, so the commands can be used to upgrade software on both an active or a standby processor.
Command Syntax
request platform software package install rp rp-slot-number file file-URL
where
The copy command can be used to move consolidated packages and individual subpackages onto the router, though using this command to move individual subpackage files from one storage area to another is often inefficient (in these scenarios, it is almost always preferable to move the consolidated package, then extract the subpackages, or to extract the subpackages without moving the consolidated package).
To upgrade a consolidated package on the Cisco cBR Series Converged Broadband Router, copy the consolidated package onto a file system, usually bootflash: , using the copy command as you would on most other Cisco routers. After making this copy, configure the router to boot using the consolidated package file.
To upgrade the router and reboot using individual subpackages, copy the consolidated package onto the router using the copy command, enter the request platform software package expand command to extract the individual subpackages, and configure the router to boot using subpackages. Other methods, such as copying each individual subpackage in the same consolidated package from a directory or using the request platform software package command to extract the subpackages onto a router directory are also usable, though copying individual subpackages is often inefficient.
This section describes methods that are used to manage and configure the packages, sub-packages and patches on the router.
The last step, in many of the methods used to upgrade and manage the packages and sub-packages, is to reload the router or the component for which the software is being configured or upgraded. Reloading the router or the components involves the following disadvantages:
service disruption (limited)
loss of modem configuration data
time consumption in rebooting the line cards and other components
The N+1 line card high availability (LCHA) system reboots the active and the standby line cards whenever a package is upgraded on a line card. This occurs for sub-package upgrade for Field Replaceable Units (FRUs) on the line card as well. Every time an upgrade is done to a package or sub-package, the line card must be rebooted. The time taken for the package upgrade on N number of active line cards, the total number of reboots would be 2xN. This is time-consuming and may affect services on the rebooting line cards.
To avoid the disadvantages of reloading the router and the line cards, use the Cable Line Card Process Restart features when you upgrade packages on the RF line cards.
Note | Do not use the process restart features without upgrading or installing packages on the RF line cards. |
Primarily there are two features that allow you to restart Cable Line Card processes:
The Cable Line Card Control Plane Process Restart feature provides the following advantages:
Simplified package upgrade without LCHA based reboot of active and standby line cards.
Restart of specific processes without service disruption.
All the modem configuration data is recovered after the IOSd process restarts.
Changes in the modem configuration data during the IOSd process restart is reconciled after the IOSd process is restarted.
The secondary line card shutdown and un-shutdown processes occur automatically.
Restrictions:
To upgrade a line card IOS using the Cable Line Card Control Plane Process Restart feature, the sub-package must have the patches for cbrsup-clcios and cbrsup-clciosdb.
IOSd and us-scheduler restart are supported. You can restart IOSd only, which requires IOSd/IOSdb packages or restart the us-scheduler only, which requires clc-docsis package. You can also restart both using a single command, where the us-scheduler is restarted first and then the IOSd is restarted. In this case, IOSd/IOSdb and clc-docsis packages are required.
Other restrictions include the following:
The IOSd process can be restarted only on the primary active RF line cards.
Any secondary RF line card must be shut down before restarting the IOSd process.
The IOSd process restart does not work when double failures (i.e. termination of IOSd and one or more process at the same time) occur. The double failures result in line card reload.
The restart of the next IOSd (i.e. IOSd process on the next RF line card) does not occur until the current IOSd process recovers fully.
The Cable Line Card Control Plane Process Restart feature provides the following restart options:
Restart a specific slot using the request platform software process restart command with the slot slot number option.
Restart all the line cards without specifying a specific slot, using the request platform software process restart command without the slot slot number option.
Interval based restart option of all line card using the request platform software process restart command with the interval secs option.
Important points to remember:
Before using the Cable Line Card Control Plane Process Restart feature, shut down the secondary line card, using the hw-module slot shutdown command.
When the Cable Line Card Control Plane Process Restart feature is started, the secondary line card shuts down automatically.
Before using the Cable Line Card Control Plane Process Restart feature, shut down the secondary line card, using the hw-module slot shutdown command.
When the Cable Line Card Control Plane Process Restart feature is started, the secondary line card shuts down automatically.
To prevent reloading the line card after sub-package upgrade, use the request platform software package install node file command with the noreload linecard option.
Verify the restart process using the show platform software ios slot slot number restart info command.
The cable line card control plane and upstream scheduler process restarts automatically after a crash. After restarting process, secondary line card is reset.
Restrictions:
The table below lists the cable line card behaviors when crash happens under different rules.
|
Secondary Cable Line Card Present |
Crash |
Secondary Cable Line Card state |
---|---|---|---|
LCHA or LCPR |
Yes |
Cable line card reset |
Active after switchover |
Process restart enabled |
No |
Restart |
N/A |
LCHA or LCPR |
Yes |
Cable line card reset |
Active after switchover |
Process restart Disabled |
No |
Cable line card reset |
N/A |
No LCHA Preferred or LCPR |
Yes |
Process restart |
Secondary cable line card resets after process restart on primary cable line card |
Process restart Enabled |
No |
Process restart |
N/A |
No LCHA Preferred or LCPR |
Yes |
Cable line card reset |
Active after switchover |
Process restart Disabled |
No |
Cable line card reset |
N/A |
Note |
|
The restart retry limit feature is added to the Cable Line Card Process Restart, it is applicable only to restart on crash. Using this feature, the customer can set a restart retry time limit, if the process cannot restart successfully within this limit, the line card will reload. This feature can prevent the line card from continuous restart when restart failed.
To use the Cable Line Card Control Plane Process Restart Feature, install the RF line card sub-package upgrade using the command.
Step 1 | Install the
RF line card sub-package upgrade using the
request platform software
package install node file noreload linecard command.
Router#request platform software package install node file bootflash:sp/cbr_patch.9.0.tar noreload linecard |
Step 2 | Use the
request platform software
process restart command to restart the RF line card IOSd process
on all the cable line cards sequentially.
Router# request platform software process restart |
Step 3 | Use the
request platform software
process restart slot slot# command to restart the RF line card IOSd
process on a specific cable line card.
Router# request platform software process restart slot 7 |
To configure the Cable Line Card Control Plane Process Restart Retry Limit, complete the following procedure:
enable configure terminal process-restart lc-control-plane-timeout time restart-retry retry-times exit
This section provides the sample outputs for the commands used in the Cable Line Card Control Plane Process.
This example shows the output of the request platform software package install node file command with the noreload linecard option that installs the sub-package upgrade:
Router# request platform software package install node file bootflash:sp/cbr_patch.9.0.tar noreload linecard Image file expanded and copied Expanding image file: stby-bootflash:sp/cbr_patch.9.0.tar Image file expanded and copied Finished image file expansion Found clc package STAGE 1: Installing software on standby RP ========================================== --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting local lock acquisition on R1 --- Finished local lock acquisition on R1 --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcios.2015-03-23_17.53_haolin2.SSA.pkg Found cbrsup-clciosdb.2015-03-23_17.53_haolin2.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatibility verification --- Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatibility verification --- Starting list of software package changes --- Old files list: Removed cbrsup-clcios.2015-03-23_17.28_haolin2.SSA.pkg Removed cbrsup-clciosdb.2015-03-23_17.28_haolin2.SSA.pkg New files list: Added cbrsup-clcios.2015-03-23_17.53_haolin2.SSA.pkg Added cbrsup-clciosdb.2015-03-23_17.53_haolin2.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. STAGE 2: Installing software on active RP ========================================= --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcios.2015-03-23_17.53_haolin2.SSA.pkg Found cbrsup-clciosdb.2015-03-23_17.53_haolin2.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatibility verification --- Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatibility verification --- Starting impact testing --- Checking operational impact of change Finished impact testing --- Starting list of software package changes --- Old files list: Removed cbrsup-clcios.2015-03-23_17.28_haolin2.SSA.pkg Removed cbrsup-clciosdb.2015-03-23_17.28_haolin2.SSA.pkg New files list: Added cbrsup-clcios.2015-03-23_17.53_haolin2.SSA.pkg Added cbrsup-clciosdb.2015-03-23_17.53_haolin2.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Found clc package SUCCESS: node ISSU finished successfully. Invoking cleanup routine
This example shows the output of the show platform software ios restart info command:
Router#show platform software ios 6 restart info IOSD process restart info: Process restartable: Yes IOSD restart state : ACTIVE Total Modem Count : 31 Active Modem Count : 31
This example shows the output of the request platform software process restart command:
Router# request platform software process restart --- Upgrading/Restarting LineCard-2 Packages/Processes --- NOTICE: No upgrades available. Provide process name in cli if you wish to restart a process --- Upgrading/Restarting LineCard-3 Packages/Processes --- Available upgrades cbrsup-clcios.2015-03-23_17.53_haolin2.SSA.pkg cbrsup-clciosdb.2015-03-23_17.53_haolin2.SSA.pkg --- Checking for ready state before IOSD upgrade on LineCard-3 Updating Package cbrsup-clcios.2015-03-23_17.28_haolin2.SSA.pkg ---> cbrsup-clcios.2015-03-23_17.53_haolin2.SSA.pkg Restarting ubrclc_k9lc_ms --- Checking for ready state before IOSDB upgrade on LineCard-3 Updating Package cbrsup-clciosdb.2015-03-23_17.28_haolin2.SSA.pkg ---> cbrsup-clciosdb.2015-03-23_17.53_haolin2.SSA.pkg Restarting iosdb SUCCESS: Finished Router#show platform software patch 2 info cbrsup-clciosdb: 3.17.0 (3.0) cbrsup-clc-firmware: 3.17.0 (0.0) cbrsup-clcvideo: 3.17.0 (0.0) cbrsup-clcios: 3.17.0 (3.0) cbrsup-clccontrol: 3.17.0 (0.0) cbrsup-clcdocsis: 3.17.0 (0.0)
The Cable Line Card Upstream Scheduler Process Restart feature is used to restart the upstream scheduler process on the RF line cards.
The Cable Line Card Upstream Scheduler Process Restart feature provides the following advantages:
Allows to restart line card US- Scheduler (CDMAN) process with minimum impact to upstream traffic and no impact to downstream traffic.
All modem configuration data recovered to the state before restart.
Changes in modem configuration data during restart are reconciled.
New modems coming online are blocked during restart.
The request platform software package restart command is used to upgrade the new DOCSIS sub-pkg patch without reloading the line card.
Effective with Cisco IOS-XE Release 3.18.0S, the card restarts automatically after a crash. For more information, see Restart on Crash section.
Restrictions:
The following restrictions apply to the :
The Upstream Scheduler process can be restarted only on the primary active RF line cards.
The Upstream Scheduler process restart does not work when double failures (i.e. termination of Upstream Scheduler and one or more process at the same time) occur. The double failures result in line card reload.
The restart of the next Upstream Scheduler (i.e. Upstream Scheduler process on the next RF line card) does not occur until the current Upstream Scheduler process recovers fully.
Important points to remember:
With Cisco IOS-XE Release 3.17.0S, when the Cable Line Card Upstream Scheduler Process Restart feature is started, the secondary line card shuts down automatically.
To prevent reloading the line card after sub-package upgrade, use the request platform software package install node file command with the noreload linecard option.
Verify the restart process using the show platform software us-scheduler restart info command.
Router# show platform software us-scheduler 3 restart info us-scheduler process restart info: Process restartable : Yes us-scheduler state : RESTART_OPERATIONAL Features bit map : 0x001e us-scheduler restart count : 4
To use the Cable Line Card Upstream Scheduler Process Restart Feature, install the RF line card sub-package upgrade using the command.
Step 1 | Install the
RF line card sub-package upgrade using the
request platform software
package install node file noreload linecard command.
Router#request platform software package install node file bootflash:sp/cbr_patch.9.0.tar noreload linecard |
Step 2 | Use the
request platform software process restart
command to restart the Upstream Scheduler process on all the cable line cards
sequentially.
Router# request platform software process restart |
Step 3 | Use the
request platform software process restart slot
slot# command to restart the Upstream Scheduler process on a
specific cable line card.
Router# request platform software process restart slot 7 |
To configure the Cable Line Card Control Plane Process Restart Retry Limit, complete the following procedure:
enable configure terminal process-restart lc-us-scheduler-timeout time restart-retry retry-times exit
This section provides the sample outputs for the commands used in the Cable Line Card Upstream Scheduler Process Restart Feature.
This example shows the output of the show platform software us-scheduler restart info command.
Router#show platform software us-scheduler 6 restart info us-scheduler process restart info: Process restartable : Yes us-scheduler state : RESTART_OPERATIONAL Features bit map : 0x001e us-scheduler restart count : 1
This example shows the output when the upstream scheduler process is restarted.
Router# request platform software package install node file bootflash:subpkg/cbr_patch-3.17.0-patch2.tar noreload linecard NOTE: Currently node has booted from a provisioning file NOTE: Going to start a dual rp sub-packages node ISSU install --- Starting initial file path checking --- Copying bootflash:subpkg/cbr_patch-3.17.0-patch2.tar to stby-bootflash:subpkg/cbr_patch-3.17.0-patch2.tar Finished initial file path checking --- Starting config-register verification --- Finished config-register verification --- Starting Checking noreload options --- Finished Checking noreload options --- Starting image file expansion --- Expanding image file: bootflash:subpkg/cbr_patch-3.17.0-patch2.tar Image file expanded and copied Expanding image file: stby-bootflash:subpkg/cbr_patch-3.17.0-patch2.tar Image file expanded and copied Finished image file expansion Found clc package STAGE 1: Installing software on standby RP ========================================== --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting local lock acquisition on R1 --- Finished local lock acquisition on R1 --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcdocsis.2015-10-08_18.10_haolin2.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatibility verification --- WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatibility verification --- Starting list of software package changes --- Old files list: Removed cbrsup-clcdocsis.BLD_MCP_DEV_LATEST_20151006_133623.SSA.pkg New files list: Added cbrsup-clcdocsis.2015-10-08_18.10_haolin2.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. STAGE 2: Installing software on active RP ========================================= --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcdocsis.2015-10-08_18.10_haolin2.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatibility verification --- WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: WARNING: WARNING: ISSU between engineering builds with release strings in non-standard fo rmat. Skipping ISSU Software Compatibility checks. WARNING: Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatibility verification --- Starting impact testing --- Checking operational impact of change Finished impact testing --- Starting list of software package changes --- Old files list: Removed cbrsup-clcdocsis.BLD_MCP_DEV_LATEST_20151006_133623.SSA.pkg New files list: Added cbrsup-clcdocsis.2015-10-08_18.10_haolin2.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Found clc package SUCCESS: node ISSU finished successfully. Invoking cleanup routine Router# Router#show platform software us-scheduler 2 restart info us-scheduler process restart info: Process restartable : Yes us-scheduler state : RESTART_OPERATIONAL Features bit map : 0x001e us-scheduler restart count : 1 Router#request platform software process restart slot 2 --- Upgrading/Restarting LineCard-2 Packages/Processes --- Available upgrades cbrsup-clcdocsis.BLD_MCP_DEV_LATEST_20151006_13362 Updating Package cbrsup-clcdocsis.BLD_MCP_DEV_LATEST_20151006_13362 ---> cbrsup-clcdocsis.2015-10-08_18.10_haolin2.SSA.pkg Restarting us-scheduler SUCCESS: Finished upgrading the LineCard-2 Router#show platform software patch 2 info cbrsup-clciosdb: 3.17.0 (0.0) cbrsup-clc-firmware: 3.17.0 (0.0) cbrsup-clcvideo: 3.17.0 (0.0) cbrsup-clcios: 3.17.0 (0.0) cbrsup-clccontrol: 3.17.0 (0.0) cbrsup-clcdocsis: 3.17.0 (2.0)
Note | If the upgrade package includes both IOSD-CLC and US-scheduler sub-packages, the request platform software process restart command first restarts the Cable Line Card Upstream Scheduler process and then the Cable Line Card Control Plane process. |
Note | If the slot keyword is not used, the upstream scheduler process on all the line cards are restarted sequentially. |
Router#request platform software process restart --- Upgrading/Restarting LineCard-1 Packages/Processes --- Available upgrades cbrsup-clcdocsis.2015-09-24_03.09_johuynh.SSA.pkg cbrsup-clcios.2015-09-24_03.09_johuynh.SSA.pkg cbrsup-clciosdb.2015-09-24_03.09_johuynh.SSA.pkg Updating Package cbrsup-clcdocsis.2015-09-24_03.09_johuynh.SSA.pkg ---> cbrsup-clcdocsis.2015-09-24_19.04_haolin2.SSA.pkg Restarting us-scheduler --- Checking for ready state before IOSD upgrade on LineCard-1 Updating Package cbrsup-clcios.2015-09-24_03.09_johuynh.SSA.pkg ---> cbrsup-clcios.2015-09-24_19.04_haolin2.SSA.pkg Restarting ubrclc_k9lc_ms --- Checking for ready state before IOSDB upgrade on LineCard-1 Updating Package cbrsup-clciosdb.2015-09-24_03.09_johuynh.SSA.pkg ---> cbrsup-clciosdb.2015-09-24_19.04_haolin2.SSA.pkg Restarting iosdb SUCCESS: Finished upgrading the LineCard-1 --- Upgrading/Restarting LineCard-2 Packages/Processes --- Available upgrades cbrsup-clcdocsis.2015-09-24_03.09_johuynh.SSA.pkg cbrsup-clcios.2015-09-24_03.09_johuynh.SSA.pkg cbrsup-clciosdb.2015-09-24_03.09_johuynh.SSA.pkg Updating Package cbrsup-clcdocsis.2015-09-24_03.09_johuynh.SSA.pkg ---> cbrsup-clcdocsis.2015-09-24_19.04_haolin2.SSA.pkg Restarting us-scheduler --- Checking for ready state before IOSD upgrade on LineCard-2 Updating Package cbrsup-clcios.2015-09-24_03.09_johuynh.SSA.pkg ---> cbrsup-clcios.2015-09-24_19.04_haolin2.SSA.pkg Restarting ubrclc_k9lc_ms --- Checking for ready state before IOSDB upgrade on LineCard-2 Updating Package cbrsup-clciosdb.2015-09-24_03.09_johuynh.SSA.pkg ---> cbrsup-clciosdb.2015-09-24_19.04_haolin2.SSA.pkg Restarting iosdb SUCCESS: Finished upgrading the LineCard-2 Router#
You can specify a time interval in seconds using the interval keyword, between the restarting of two line card processes in the sequence. The default interval is five seconds.
This example shows the configuration of an interval of six seconds.
Router#request platform software process restart interval 6
The following instructions provide a quick start version of upgrading the software running the Cisco cBR Series Converged Broadband Router. These instructions assume you have access to the consolidated package and that the files will be stored in a bootflash: file system that is not storing any previously installed subpackages or consolidated packages and that has enough room for the file or files.
Step 1 | Copy the consolidated package into bootflash: using the copy URL-to-image bootflash: command. |
Step 2 | If you want to run the router using individual subpackages, enter the request platform software package expand file bootflash:/sub_dir/base_image command. If you want to run the router using a consolidated package, skip this step. |
Step 3 | Enter the dir bootflash: command to verify your consolidated package or your extracted subpackages are in the directory. |
Step 4 | If you are trying to run individual subpackages, use the delete bootflash:base_image to delete the consolidated package. If you want to run the router using the consolidated package, skip this step. |
Step 5 | Set up the boot parameters for your boot. Set the configuration register to 0x2 by entering the config-register 0x2102 global configuration command, and enter the boot system flash bootflash:base_image (if running using the consolidated package) or boot system flash bootflash:provisionging-file-name (if running using individual subpackages) global configuration command. |
Step 6 | Enter copy running-config startup-config to save your configuration. |
Step 7 | Enter the reload command to reload the router and finish the boot. The upgraded software should be running when the reload completes. |
To upgrade a consolidated package on the Cisco cBR Series Routers using the copy command, copy the consolidated package into the bootflash: directory on the router using the copy command as you would on most other Cisco routers. After making this copy, configure the router to boot using the consolidated package file.
In the following example, the consolidated package file is copied onto the bootflash: file system from TFTP. The config-register is then set to boot using boot system commands, and the boot system commands instruct the router to boot using the consolidated package stored in the bootflash: file system. The new configuration is then saved using the copy running-config startup-config command, and the system is then reloaded to complete the process.
Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (712273920 bytes free) Router# copy tftp bootflash: Address or name of remote host []? 172.17.16.81 Source filename []? /auto/tftp-users/user/cbrsup-universal*.bin Destination filename [cbrsup-universal*.bin]? Accessing tftp://172.17.16.81//auto/tftp-users/user/ cbrsup-universal*.bin... Loading /auto/tftp-users/user/cbrsup-universal*.bin from 172.17.16.81 (via GigabitEthernet0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!! [OK - 208904396 bytes] 208904396 bytes copied in 330.453 secs (632176 bytes/sec) Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw- 208904396 May 28 2008 16:17:34 -07:00 cbrsup-universal*.bin 13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (503156736 bytes free) Router# config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#boot system flash bootflash:cbrsup-universal*.bin Router(config)#config-reg 0x2102 Router(config)#exit Router#show run | include boot boot-start-marker boot system flash bootflash:cbrsup-universal*.bin boot-end-marker Router# copy run start Destination filename [startup-config]? Building configuration... [OK] Router# reload
To run the router using individual subpackages from a consolidated package, follow one of the following procedures:
T o extract a consolidated package and to boot using provisioning file, perform the following steps:
Step 1 | Perform one
of the following tasks:
| ||
Step 2 | Configure the
router to boot using the provisioning file.
The sequence below provides an example that would boot the router using the provisioning file named packages.conf that was stored with the other subpackages in the bootflash: file system: Router(config)# no boot system Router(config)# config-register 0x2102 Router(config)# boot system flash bootflash:packages.conf Router(config)# exit *May 11 01:31:04.815: %SYS-5-CONFIG_I: Configured from console by con Router# copy running-config startup-config Building configuration... [OK] Router# reload Extracting the SubPackages and the Provisioning File: Example 1 The following example shows how to extract the individual subpackages and the provisioning file from a consolidated package that has already been placed in the directory where you want to store the individual subpackages and the provisioning file. We recommend that you extract the sub packages to an empty directory to simplify the management of these files. Output of the directory before and after the extraction is given to confirm the files were extracted. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw- 208904396 May 9 2008 14:36:31 -07:00 cbrsup-universal*.bin 13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (503156736 bytes free) Router# request platform software package expand file bootflash:cbrsup-universal*.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw- 208904396 May 9 2008 14:36:31 -07:00 cbrsup-universal*.bin 57611 -rw- 47071436 May 22 2008 11:26:23 -07:00 cbr000rp1-espbase.02.01.00.122-33.XNA.pkg 57602 -rw- 5740 May 22 2008 11:26:22 -07:00 cbr000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 57612 -rw- 20334796 May 22 2008 11:26:24 -07:00 cbr000rp1-rpaccess.02.01.00.122-33.XNA.pkg 57613 -rw- 22294732 May 22 2008 11:26:24 -07:00 cbr000rp1-rpbase.02.01.00.122-33.XNA.pkg 57614 -rw- 21946572 May 22 2008 11:26:25 -07:00 cbr000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 57615 -rw- 48099532 May 22 2008 11:26:26 -07:00 cbr000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 57616 -rw- 34324684 May 22 2008 11:26:27 -07:00 cbr000rp1-sipbase.02.01.00.122-33.XNA.pkg 57617 -rw- 22124748 May 22 2008 11:26:28 -07:00 cbr000rp1-sipspa.02.01.00.122-33.XNA.pkg 57603 -rw- 6256 May 22 2008 11:26:28 -07:00 packages.conf 13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (286662656 bytes free) Extracting the SubPackages, Configuring the Router to Boot Using the Provisioning File, and Reloading the Router: Example 2 In the following example, the provisioning file and the individual subpackages are extracted from a consolidated package. The router is then configured to boot using the provisioning file. This example also shows the config-register being set and the running configuration being saved because these tasks must be performed for the router to reload properly. The router is then reloaded to complete the process. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw- 208904396 May 9 2008 14:36:31 -07:00 cbrsup-universal*.bin 13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (503156736 bytes free) Router# request platform software package expand file bootflash:cbrsup-universal*.bin Verifying parameters Validating package type Copying package files SUCCESS: Finished expanding all-in-one software package. Router# dir bootflash: Directory of bootflash:/ 11 drwx 16384 Dec 4 2007 04:32:46 -08:00 lost+found 86401 drwx 4096 Dec 4 2007 06:06:24 -08:00 .ssh 14401 drwx 4096 Dec 4 2007 06:06:36 -08:00 .rollback_timer 28801 drwx 4096 Mar 18 2008 17:31:17 -07:00 .prst_sync 43201 drwx 4096 Dec 4 2007 04:34:45 -08:00 .installer 12 -rw- 208904396 May 9 2008 14:36:31 -07:00 cbrsup-universal*.bin 57611 -rw- 47071436 May 22 2008 11:26:23 -07:00 cbr000rp1-espbase.02.01.00.122-33.XNA.pkg 57602 -rw- 5740 May 22 2008 11:26:22 -07:00 cbr000rp1-packages-adventerprisek9.02.01.00.122-33.XNA.conf 57612 -rw- 20334796 May 22 2008 11:26:24 -07:00 cbr000rp1-rpaccess.02.01.00.122-33.XNA.pkg 57613 -rw- 22294732 May 22 2008 11:26:24 -07:00 cbr000rp1-rpbase.02.01.00.122-33.XNA.pkg 57614 -rw- 21946572 May 22 2008 11:26:25 -07:00 cbr000rp1-rpcontrol.02.01.00.122-33.XNA.pkg 57615 -rw- 48099532 May 22 2008 11:26:26 -07:00 cbr000rp1-rpios-adventerprisek9.02.01.00.122-33.XNA.pkg 57616 -rw- 34324684 May 22 2008 11:26:27 -07:00 cbr000rp1-sipbase.02.01.00.122-33.XNA.pkg 57617 -rw- 22124748 May 22 2008 11:26:28 -07:00 cbr000rp1-sipspa.02.01.00.122-33.XNA.pkg 57603 -rw- 6256 May 22 2008 11:26:28 -07:00 packages.conf 13 -rw- 45977 Apr 9 2008 16:48:46 -07:00 target_support_output.tgz.tgz 928862208 bytes total (286662656 bytes free) Router(config)# no boot system Router(config)# config-register 0x2102 Router(config)# boot system flash bootflash:packages.conf Router(config)# exit Router# copy run start Router# reload |
To copy a set of individual subpackage files and to boot using a provisioning file, perform the following steps:
Note | Although this upgrade method works, it is less efficient than other methods of upgrading the router's software. |
Step 1 | Copy each individual
subpackage and the provisioning file into the bootflash: directory using the
copy command. Note that this method of
running the router will only work if all the individual subpackages for a
release and a provisioning file are downloaded onto the router and stored in
the bootflash: directory. No other file directories should be used for booting
the router using individual subpackages.
The files can also be moved on the router physically using a USB Flash drive. |
Step 2 | Configure the router to boot
using the provisioning file.
The sequence below provides an example that describes how to boot the router using the provisioning file named packages.conf that was stored with the other subpackages in the bootflash: file system. The router runs using individual subpackages once the reload is complete. Router(config)# no boot system Router(config)# config-register 0x2102 Router(config)# boot system flash bootflash:packages.conf Router(config)# exit *May 11 01:31:04.815: %SYS-5-CONFIG_I: Configured from console by con Router# write memory Building configuration... [OK] Router# reload |
To run the router using an optional subpackage, perform the following steps for each Supervisor in the chassis:
Step 1 | Verify that the Supervisor is running in individual subpackage mode and was booted from a provisioning file. |
Step 2 | Verify that the version of the optional subpackage that you want to install is the same version as the software running on the active Supervisor. |
Step 3 | Download the optional subpackage that you want to install. Optional subpackages must be downloaded independently from consolidated packages for the Cisco cBR Series Routers. |
Step 4 | On each Supervisor, copy the optional subpackage to the directory where any other individual subpackages and the provisioning file is located. |
Step 5 | Run the
request platform software package install rp
file command, as shown in the following example.
Note Do not use the optional slot or bay keywords for the initial installation. Router# request platform software package install rp 0 file bootflash: cbrsup-universal*.bin --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Verifying image file locations Locating image files and validating name syntax Found cbrsup-universal*.bin Inspecting image file types Processing image file constraints Creating candidate provisioning file WARNING: No package of type sipspawmak9 is installed. WARNING: Package will be installed for all SIP slots and bays. Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting compatibility testing --- Determining whether candidate package set is compatible WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Determining whether installation is valid WARNING: WARNING: Candidate software combination not found in compatibility database WARNING: Software sets are identified as compatible Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished compatibility testing --- Starting impact testing --- Checking operational impact of change Finished impact testing --- Starting list of software package changes --- No old package files removed New files list: Added cbrsup-universal*.bin Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. |
Upgrading Individual SubPackages
Individual subpackages can be upgraded in subpackage mode. Patch releases consist of one or more subpackages. After a patch has been installed, a message is displayed indicating whether the entire chassis or only the line cards must be rebooted for the updates to take effect.
Step 1 | The Cisco cBR router must be in subpackage mode. |
Step 2 | Copy the patch file to the same location as the active subpackages on both the active and standby supervisor cards. |
Step 3 | Install the patch using the request platform software package install rp slot file patch file command on the standby card. |
Step 4 | Install the patch using therequest platform software package install rp slot file patch file command on the active card. |
Step 5 | Reload the chassis. |
Step 1 | The Cisco cBR router must be in subpackage mode. |
Step 2 | Copy the patch file to the same location as the active subpackages on both the active and standby supervisor cards. |
Step 3 | Install the patch using the request platform software package install rp slot file patch file command on the standby card. |
Step 4 | Install the patch using therequest platform software package install rp slot file patch file command on the active card. |
Step 5 | Reload the line cards. |
Step 1 | The Cisco cBR router must be in subpackage mode. |
Step 2 | Copy the patch file to the same location as the active subpackages on both the active and standby supervisor cards. |
Step 3 | Install the patch using the request platform software package install rp slot file patch file command on the standby card. |
Step 4 | Switch over to the standby card. This will make it the active card. |
Step 5 | Install the patch using the request platform software package install rp slot file patch file command on the standby card. |
Use the request platform software package install node file filename command to upgrade a line card subpackage.
Router# request platform software package install node file bootflash:/subpkg/cbr_patch.5.0.tar NOTE: Currently node has booted from a provisioning file NOTE: Going to start a dual rp sub-packages node ISSU install --- Starting initial file path checking --- Copying bootflash:/subpkg/cbr_patch.5.0.tar to stby-bootflash:/subpkg/cbr_patch.5.0.tar Finished initial file path checking --- Starting config-register verfication --- Finished config-register verfication --- Starting image file expansion --- Expanding image file: bootflash:/subpkg/cbr_patch.5.0.tar Image file expanded and copied Expanding image file: stby-bootflash:/subpkg/cbr_patch.5.0.tar Image file expanded and copied Finished image file expansion STAGE 1: Installing software on standby RP ========================================== --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting local lock acquisition on R1 --- Finished local lock acquisition on R1 --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcdocsis.2015-02-20_01.02.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatiblity verficiation --- Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatiblity verficiation --- Starting list of software package changes --- Old files list: Removed cbrsup-clcdocsis.BLD_V155_2_S_XE315_THROTTLE_LATEST_20150217_110041-st d.SSA.pkg New files list: Added cbrsup-clcdocsis.2015-02-20_01.02.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. STAGE 2: Installing software on active RP ========================================= --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcdocsis.2015-02-20_01.02.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatiblity verficiation --- Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatiblity verficiation --- Starting impact testing --- Checking operational impact of change Finished impact testing --- Starting list of software package changes --- Old files list: Removed cbrsup-clcdocsis.BLD_V155_2_S_XE315_THROTTLE_LATEST_20150217_110041-st d.SSA.pkg New files list: Added cbrsup-clcdocsis.2015-02-20_01.02.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Found clc package Found clc package Found clcdocsis package SUCCESS: Reload Cable Linecard at slot 1 SUCCESS: Reload Cable Linecard at slot 2 SUCCESS: node ISSU finished successfully. Invoking cleanup routine
Use the request platform software package install node file filename noreload linecard command to upgrade a line card subpackage.
Router#request platform software package install node file bootflash:/subpkg/cbr_patch.5.0.tar noreload linecard NOTE: Currently node has booted from a provisioning file NOTE: Going to start a dual rp sub-packages node ISSU install --- Starting initial file path checking --- Copying bootflash:/subpkg/cbr_patch.5.0.tar to stby-bootflash:/subpkg/cbr_patch. 5.0.tar Finished initial file path checking --- Starting config-register verfication --- Finished config-register verfication --- Starting Checking noreload options --- Finished Checking noreload options --- Starting image file expansion --- Expanding image file: bootflash:/subpkg/cbr_patch.5.0.tar Image file expanded and copied Expanding image file: stby-bootflash:/subpkg/cbr_patch.5.0.tar Image file expanded and copied Finished image file expansion Found clc package STAGE 1: Installing software on standby RP ========================================== --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting local lock acquisition on R1 --- Finished local lock acquisition on R1 --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcdocsis.2015-03-01_01.40.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatiblity verficiation --- Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatiblity verficiation --- Starting list of software package changes --- Old files list: Removed cbrsup-clcdocsis.2015-03-01_03.43.SSA.pkg New files list: Added cbrsup-clcdocsis.2015-03-01_01.40.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. STAGE 2: Installing software on active RP ========================================= --- Starting local lock acquisition on R0 --- Finished local lock acquisition on R0 --- Starting installation state synchronization --- Finished installation state synchronization --- Starting file path checking --- Finished file path checking --- Starting image file verification --- Checking image file names Locating image files and validating name syntax Found cbrsup-clcdocsis.2015-03-01_01.40.SSA.pkg Verifying image file locations Inspecting image file types Processing image file constraints Creating candidate provisioning file Finished image file verification --- Starting candidate package set construction --- Verifying existing software set Processing candidate provisioning file Constructing working set for candidate package set Constructing working set for running package set Checking command output Constructing merge of running and candidate packages Checking if resulting candidate package set would be complete Finished candidate package set construction --- Starting ISSU compatiblity verficiation --- Verifying image type compatibility Checking IPC compatibility with running software Checking candidate package set infrastructure compatibility Checking infrastructure compatibility with running software Checking package specific compatibility Finished ISSU compatiblity verficiation --- Starting impact testing --- Checking operational impact of change Finished impact testing --- Starting list of software package changes --- Old files list: Removed cbrsup-clcdocsis.2015-03-01_03.43.SSA.pkg New files list: Added cbrsup-clcdocsis.2015-03-01_01.40.SSA.pkg Finished list of software package changes --- Starting commit of software changes --- Updating provisioning rollback files Creating pending provisioning file Committing provisioning file Finished commit of software changes --- Starting analysis of software changes --- Finished analysis of software changes --- Starting update running software --- Blocking peer synchronization of operating information Creating the command set placeholder directory Finding latest command set Finding latest command shortlist lookup file Finding latest command shortlist file Assembling CLI output libraries Assembling CLI input libraries Assembling Dynamic configuration files Applying interim IPC and database definitions Replacing running software Replacing CLI software Restarting software Restarting software: target frus filtered out ... skipped Applying final IPC and database definitions Generating software version information Notifying running software of updates Unblocking peer synchronization of operating information Unmounting old packages Cleaning temporary installation files Finished update running software SUCCESS: Finished installing software. Found clc package SUCCESS: node ISSU finished successfully. Invoking cleanup routine
Use the show platform software patch n info command to verify completion of this upgrade.
Router#show platform software patch 1 info cbrsup-clciosdb: 3.15 (0.0) cbrsup-clc-firmware: 3.15 (0.0) cbrsup-clcvideo: 3.15 (0.0) cbrsup-clcios: 3.15 (0.0) cbrsup-clccontrol: 3.15 (0.0) cbrsup-clcdocsis: 3.15 (1.0) cbrsup-clcmipsbase: 3.15 (0.0) Router#show platform software patch 2 info cbrsup-clciosdb: 3.15 (0.0) cbrsup-clc-firmware: 3.15 (0.0) cbrsup-clcvideo: 3.15 (0.0) cbrsup-clcios: 3.15 (0.0) cbrsup-clccontrol: 3.15 (0.0) cbrsup-clcdocsis: 3.15 (1.0) cbrsup-clcmipsbase: 3.15 (0.0)
Use the show platform software ios slot-number restart info command to verify completion of this upgrade. This example shows the output of this show command for the RF line card slot number 2.
Router#show platform software ios 2 restart info IOSD process restart info: Process restartable: Yes IOSD restart state : NOT_RESTARTED_YET Total Modem Count : 251 Active Modem Count : 251 Router#
Description | Link |
---|---|
The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies. To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Access to most tools on the Cisco Support website requires a Cisco.com user ID and password. |
Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Note | The table below lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature. |
Feature Name |
Releases |
Feature Information |
---|---|---|
Consolidated Packages and SubPackages Management |
Cisco IOS XE Fuji 16.7.1 |
This feature was integrated on the Cisco cBR Series Converged Broadband Routers. |