Field Notice: FN - 63952 - uBR10012 - SPA-UBR10-DS-HD Card, with New License Flash Chip, Incompatibility with 12.2(33)SCI FPD Image - Workaround Provided

Available Languages

Updated:January 14, 2019

Document ID:FN63952

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Notice

THIS FIELD NOTICE IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTY OF MERCHANTABILITY. YOUR USE OF THE INFORMATION ON THE FIELD NOTICE OR MATERIALS LINKED FROM THE FIELD NOTICE IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS FIELD NOTICE AT ANY TIME.

Revision History

Revision	Publish Date	Comments
1.0	10-Jun-15	Initial Release
10.0	19-Oct-17	Migration to new field notice system
10.1	14-Jan-19	Fixed Broken Image Links

Products Affected

Affected Product ID	Comments
SPA-UBR10-DS-HD	Version V02 or higher impacted
SPA-UBR10-DS-HD=	Version V02 or higher impacted
SPA-UBR10-DS-SP=	Version V02 or higher impacted

Defect Information

Defect ID	Headline
CSCus62594	Commit new fpga image that support new license flash

Problem Description

The SPA-UBR10-DS-HD card with the new License Flash Chip does not work with the Cisco IOS^® Software Release 12.2.33-IOS SCI FPD image in cases where the Shared Port Adapter (SPA) is upgraded from 3G to 6G capacity or downgraded from 6G to 3G capacity.

The Cisco Universal Broadband Router (uBR10012) 3G SPA card (SPA-UBR10-DS-HD) will soon transition to a new License Flash Chip. The new chip is supported by the Cisco IOS software Version 12.2.33-SCI1 or later FPD image.

Note: No action is required if the SPA card remains with its original 3G capacity without an upgrade or downgrade.

Background

The Field Programmable Gate Array (FPGA) hardware on the SPA-UBR10-DS-HD card is a Field Programmable Device (FPD). The capacity downgrade/upgrade for this SPA (3G to 6G, or vice versa) is performed via a change of the FPGA image.

The FPD image for this SPA is stored on the disk0 of PRE5, and the customer must manually download the correct FPD image version from Cisco.com.

From June 11, 2015 onwards, the SPA-UBR10-DS-HD card License Flash Chip will transition to a new chip from a different vendor.

The current IOS release in the field (12.2-33-SCI) FPD image does not support an upgrade of the 3G to 6G capacity or the downgrade from 6G to 3G capacity on the SPA card with the new License Flash Chip.

In order to allow a successful SPA capacity change with the new License Flash Chip, a new FPD image must be installed for the uBR10012 routers that run Cisco IOS Release 12.2.33-SCI.

Problem Symptom

This message will be observed in the error logs if an SPA card the new License Flash Chip is upgraded or downgraded with the old FPGA image:

* Jan 23 11:24:33.659 CST: %LICENSE-2-LIC_STORAGE_CORRUPT: Corrupted storage.

  Please reinstall all licenses. UDI=UBR10-PRE5:CAT xxxxxxx

Workaround/Solution

Cisco recommends installation of the FPD flash image for the SPA-UBR10-DS-HD card that has the new License Flash Chip for uBR10012 routers that run IOS Release 12.2.33-SCI. This action must be taken only for the SPAs that are upgraded from 3G to 6G capacity.

Note: There is no action required for the SPA cards that have the new License Flash Chip and that will remain with the default 3G capacity.

Refer to this table in order to determine the required action for your specific deployment:

FPD Installation

Complete these steps in order to install the FPD image:

Use your cisco.com credentials in order to download the SCI1 FPD image package.
Rename the ubr10k-fpd-pkg.122-33.SCI1.pkg file to ubr10k-fpd-pkg.122-33.SCI.pkg.
Place the renamed FPD image package on disk0 of the Cisco uBR10012 router.
Follow the normal FPD upgrade process.

Note: Refer to the Manually Upgrading the Cisco 3 Gbps Wideband Shared Port Adapter FPD to Cisco 6 Gbps Wideband Shared Port Adapter section of the Cisco uBR10012 Universal Broadband Router SIP and SPA Software Configuration Guide for more information about the normal FPD upgrade process.

How To Identify Affected Products

The hardware information can be verified either with the CLI or with a visual inspection of the SPA card, as shown in the sections that follow.

Verify Hardware with the CLI

Verify Hardware with a Visual Inspection

For More Information

If you require further assistance, or if you have any further questions regarding this field notice, please contact the Cisco Systems Technical Assistance Center (TAC) by one of the following methods:

Receive Email Notification For New Field Notices

Cisco Notification Service—Set up a profile to receive email updates about reliability, safety, network security, and end-of-sale issues for the Cisco products you specify.