This document answers some frequently asked questions about Cisco Secure Access Control Server (ACS) for Windows.
A. Yes. ACS 4.2.1 provides 64-bit Windows support for ACS Windows and ACS remote agent. ACS versions prior to 4.2.1 does not support the 64-bit operating system.
A. No. The authorization command is available only with ACS (not with ACS Express).
A. ACS 4.1 and 4.2 have been tested on the VMWare ESX server with this configuration:
VMWare ESX Server 3.0.0
16 GB of RAM
AMD Opteron Dual Core processor
300 GB hard drive
Four virtual machines
Windows 2003 Standard Edition
3 GB of RAM for the guest operating system
Q. When was Point-to-Point Tunneling Protocol (PPTP) with Microsoft Point-to-Point Encryption (MPPE) keying support added to Cisco Secure ACS for Windows?
A. PPTP version 2.6 requires Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) authentication if MPPE keying (encryption) is to be done. In earlier versions, PPTP authentication is possible. However, support for MPPE keying was not added until ACS version 2.6.
A. ACS presently supports MS-CHAP version 1. ACS versions 3.0 and later support MS-CHAP versions 1 and 2.
A. Yes. It is possible to use Radius on ACS version 5.2 in order to configure authentication for the Cisco VPN Client. ACS version 5.0 does not support the use of Radius to configure authentication for the Cisco VPN Client.
A. Yes, an ACS and the SDIs Access Control Entry (ACE) server can be run on the same machine. There is also a client-server arrangement with an ACS and ACE Client on one machine and the ACE server on another.
Q. What are the differences between Password Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP)? Why is CHAP unable to be used with the NT database?
A. PAP sends passwords in the clear between the user and the TACACS+ or RADIUS client or device. If the password is correct, the authentication is acknowledged. Otherwise, the connection is terminated.
CHAP sends a challenge message to the remote user. The remote user responds with a value that calculates with the use of a one-way hash function. The client or device checks the response against its own calculation of the expected hash value. If the values match, the authentication is acknowledged. Otherwise, the connection is terminated. Passwords are not sent in the clear.
CHAP cannot be used with the NT database because of the CHAP RFC (1994) requirement. It states:
"CHAP requires that the secret be available in plaintext form. Irreversibly encrypted password databases commonly available cannot be used."
This generally precludes the use of the NT database for CHAP, with Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) as an option.
Microsoft offers a hotfix that can provide a workaround for Microsoft Windows NT user databases. It allows user passwords to be saved in plain text format. For additional information, refer to CHAP Update for IAS (NT4.0 RADIUS Server) Authentication to Windows NT4.0 Domain Controllers .
A. Yes, ACS receives authentication requests from the network access servers (NASes) and forwards them to other servers. You need to define the other servers. In order to do this, select Network Configuration > AAA Servers on the source. The source server is defined as a TACACS+ or RADIUS NAS on the target. Once those are defined, configure the Distributed System Settings in the source Network Configuration in order to define the proxy parameters.
A. There is no limit because it is a function of how much the Windows NT registry supports. This is estimated to be thousands of servers. NAS information is not stored in the database. It is stored in the registry. Therefore, when you issue the csutil -d command, you do not back up any NAS information.
A. ACS has its own proprietary database. It is stored in multiple files.
A. Yes. ACS does support domain stripping. This is useful when there is a combination of Virtual Private Dialup Network (VPDN) and non-VPDN users.
Another use for domain stripping is when the external NT database is used for authentication. The first time the users log in, the user name is autopopulated in ACS. Since a user probably comes in as DOMAIN_A\user or as user, names can appear in ACS as "DOMAIN_A\user" or as "user." This results in both entries in the database. The duplicate entries can be avoided with the use of domain stripping. This is where the prefix domain with the delimiter \ can be erased in order to have a consistent database. In order to set this up, select Network Configuration > Proxy Distribution Table.
A. ACS supports RDBMS databases, such as Oracle, in order to synchronize the database between two systems that use any RDBMS.
A. In ACS versions 3.0 and later, the CRYPTOAdmin server component is removed from ACS. Any future licenses, free or otherwise, must be obtained directly from CRYPTOCard.
A. No. DHCP relay is not supported on the ACS.
A. No. It is not possible to change the hostname of the ACS server running on Windows. The ACS is designed by default to take the Windows server name as the hostname.
A. Yes. ACS is supported on Windows Server 2008, and is available from ACS 4.2 Patch 4 and later. Refer to the Windows and Active Directory 2008 Supported Scenarios section in Release Notes for Cisco Secure ACS 4.2 for more information.
A. No. SNMP is supported only on the ACS appliance. Refer to the SNMP Support section of the Supported Interoperable Devices and Software Tables for Cisco Secure ACS Release 4.2 document.
A. No. IPv6 is not supported on ACS.
A. No. PEAP-TLS is not supported on ACS.
A. The degree of RADIUS support depends on the version of ACS. Request For Comments (RFCs) 2138 and 2139 are always supported, as are Cisco IOS® Software vendor-specific attributes (VSAs). For a list of RADIUS support in a particular version, select Network Configuration > Network Device Groups > AAA Clients Area.
A. ACS proxies from RADIUS-to-RADIUS or from TACACS+-to-TACACS+, but it cannot proxy between dissimilar protocols.
Q. How do I assign Domain Naming System (DNS) and Windows Internet Naming Service (WINS) server IP addresses for PPP connections from ACS using TACACS+?
A. You are able to specify DNS and WINS server IP addresses from the ACS on a per-user basis or for a group of users with the addition of these lines as custom attributes of PPP IP in the group setup.dns-servers = 10.1.1.1 10.1.1.3 wins-servers = 10.1.1.5 10.1.1.16
Q. How do I assign Domain Naming System (DNS) and Windows Internet Naming Service (WINS) server IP addresses for PPP connections from ACS using RADIUS?
A. You are able to specify DNS and WINS server IP addresses from the ACS on a per-user basis or for a group of users with the addition of these lines under Cisco RADIUS Attributes and AV-pair in group setup.ip:wins-server=22.214.171.124 126.96.36.199 ip:dns-servers=188.8.131.52 184.108.40.206
A. Since version 2.5, ACS listens on RADIUS ports User Datagram Protocol (UDP) 1645 and UDP 1812 for authentication and on ports 1646 and 1813 for accounting.
If you use an older version, change the listening ports. In order to do this, re-edit the attribute values of the proper key in the Windows Registry:HKEY_LOCAL_MACHINE\SOFTWARE\Cisco\CiscoAAAv2.3\CSRadius "AuthenticationPort"=dword:1812 "AccountingPort"=dword:1813 This can also be changed in the newer version: HKEY_LOCAL_MACHINE\SOFTWARE\Cisco\CiscoAAAv3.0\CSRadius AccountingPort = 1646 AccountingPortNew = 1813 AuthenticationPort = 1645 AuthenticationPortNew = 1812
A. Change the default value of the port for TACACS+ services. In order to do this, edit the attribute values of the proper key in the Windows Registry:HKEY_LOCAL_MACHINE\SOFTWARE\Cisco\CiscoAAAv3.0\CSTacacs "Port"=dword:59
Q. I do not want the administrative overhead of having to list all the network access servers (NASes) in my network, and they all have the same tacacs-server keys. How do I set up a default key to use with my NASes?
A. Add a default NAS in the NAS configuration area by leaving the host name and IP address blank. Enter only the key. Click Submit. You then see NAS others and *.*.*.*.
Note: This procedure only works for TACACS+, and not RADIUS.
Q. I want to have a device "speak" both TACACS+ and RADIUS with ACS for authentication. I want one for dial and the other for router management. How can I do this?
A. Configure a default network access server (NAS) as described in the previous question for TACACS+, and then enumerate the NAS for RADIUS. The NAS sends RADIUS dial requests to ACS on the RADIUS port if the aaa authentication ppp default if-needed RADIUS command is issued.
The NAS sends TACACS+ Router Management requests to ACS on the TACACS+ port if the aaa authentication login default TACACS+ command is issued.
A. Complete these steps in order to troubleshoot the problem.
- Check to see if you can authenticate the user on the local domain. In order to ensure this, select Start > Shutdown > Close all programs and log on as a different user. If you cannot authenticate the user on the local domain, ACS does not work.
- If you have checked verify grant dialin permission for the users in the Cisco Secure database configuration, check to see if dialin permission is granted for this user in the NT database.
- If this is a dial connection, make sure that Password Authentication Protocol (PAP) or Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) (not CHAP) is configured on the router and PC.
Q. What do I need to check when users are unable to authenticate against the Novell Directory Server (NDS) database?
A. Check to see if the tree name, context name, and container name are all specified correctly. Start with one container where users are present. You can add more containers later.
If you are successful, check the NAS in order to see if you are able to authenticate the shell user (Telnet user). Also ensure that for PPP you have Password Authentication Protocol (PAP) authentication configured on the asynchronous interface.
A. Complete these steps in order to troubleshoot an SDI authentication problem.
- Authenticate the user with the Access Control Entry (ACE) test agent.
- If this works, confirm that the card is synchronized with the database. Ensure you use Data Encryption Standard (DES) encryption on the SDI server when the card is initialized. A choice of SDI does not work.
- Bring up the activity monitor on the ACE server while you attempt Telnet authentication to a device.
- Check to see if there are any errors on the activity monitor on the ACE server.
- If the ACE server works, but there is a problem with the dial users, check the settings on the network access servers (NAS) in order to ensure that Password Authentication Protocol (PAP) is configured. Then try to connect as a non-SDI user.
- If this works, connection as an SDI user is expected to work. Enter the user name in the user name tab and the passcode in the password tab on Dial-up Networking.
- If the client from where you dial is configured to bring up the post terminal screen after you dial, ensure you issue this authentication, authorization, and accounting (AAA) command on the NAS:The key is to use if-needed. This means that the user is already authenticated by issuing this AAA command:aaa authentication ppp default if-needed tacacs+/RadiusThen you do not have to authenticate the user again when you do PPP. This also applies when you use the normal PAP password.aaa authentication login default tacacs+/radius
A. Select Interface Configuration > Tacacs+ (Cisco) > Add New Service. Assign ppp as the service and multilink as the protocol.
Note: PPP and multilink are all lower case.
A. A full description of the license terms and conditions and future upgrades are obtained by sending an E-mail to email@example.com, the product code to use as a reference is CA5.1SC. A CRYPTOAdmin Server software evaluation package, that includes a time-limited license and software tokens, are obtained from CRYPTOCard's Download page .
Q. When I turn on enable authentication in the switch or router with commands such as aaa authentication enable default tacacs+ or set authentication login tacacs enable telnet primary, I am locked out of enable mode and receive the Error in authentication error message on the router. What do I need to do?
A. Check the failed attempts log in the ACS. If the log says CS password invalid, it can be that there has not been a special enable password set up for the user. This is required when you configure enable authentication. If you do not see Advanced TACACS+ Settings in the user options, select Interface Configuration > Advanced Configuration Options > Advanced TACACS+ Features and select that option in order to get the TACACS+ settings to appear in the user settings. Then select Max privilege for any AAA Client (this is usually 15) and enter the TACACS+ Enable Password that you want the user to have for enable.
A. Note the date and time of the message, go to the CSAuth log file, and search on the date and time. A more detailed explanation of the message is then presented.
A. This issue occurs when the user does not provide a domain name. If the domain name is not provided, ACS Express attemps to append the domain name of the domain that the ACS Express is joined. If a user resides in a sub-domain, and the ACS Express is joined to a parent domain, then the user needs to provide a fully qualified domain name in the user name authentication.
A. No. ACS does not support QoS in authentication. ACS will not prioritize RADIUS authentication requests over TACACS or TACACS requests over RADIUS.
A. The NAS reset messages can be caused by a reboot of the device or by issuing the tacacs-server host #.#.#.# single-connection command on the Cisco IOS Software. If the device does not reboot, issue the tacacs-server host #.#.#.# command in order to change the configuration to eliminate the messages.
A. Yes. Choose System Configuration > Logging in order to configure this option.
Q. Does Cisco recommend a software application that can be used to do reporting on accounting logs available in ACS?
A. The ACS accounting logs are recorded in one of two formats:
CSV files—The comma-separated value (CSV) format records data in columns separated by commas. This format is easily imported into a variety of third-party applications, such as Microsoft Excel or Microsoft Access. After data from a CSV file is imported into such applications, prepare charts or perform queries, such as to determine how many hours a user is logged in to the network during a given period.
ODBC-compliant database tables—Open database connectivity (ODBC) logging allows you to configure ACS to log directly into an ODBC-compliant relational database, where information is stored in tables, one table per log. After the data is exported to the relational database, use the data in any way you need.
With either method, software used to parse logs is widely available. However, Cisco does not recommend a particular vendor.
Q. Does ACS Accounting information (any change occurs) parse to the Monitoring, Analysis, and Response System (MARS)?
A. Unfortunately, the current support in MARS does not have parsing capability for anything other than Failed Attempts, Passed Authentications, and RADIUS Accounting logs.
In ACS 5.0, ACS View will be the vehicle for ACS monitoring and reporting, more than MARS.
A. You can back up ACS through the GUI with the help of the System Configuration tab, or use the command-line interface (CLI). If you use the GUI, there is a backup of the users, groups, and registry settings. If you use the CLI, issue these commands:
For a dump of users and groups:$BASE\utils\csutil -d
For a backup of users, groups, and registry settings:$BASE\utils\csutil -b
For more information on how to perform an ACS backup, refer to How to backup the Cisco Secure ACS for Windows database.
A. No. The backup utility is intended to save the user, group, and registry information from one ACS box and restore it to the same ACS box that runs the same version of software. If there is a need to clone an ACS box, replication is available instead.
If you need to copy only users and groups from one server to another, issue the csutil -d command. The new dump text (.txt) file is then copied to the target box. After this, issue the csutil -n -l command in order to initialize the database and import the users and groups.
Q. I get the CSBackupRestore(OUT) cannot save reg key error message when I try to backup the data on ACS. Why does this error occur?
A. This error occurs when the disk on which the ACS is installed is completely full or write protected. Make sure that there is enough free disk space and it is not write protected so that the error does not occur again.
Q. With Cisco Secure you can force the users to change their passwords after a given time period. Are you able to do this when you use the Windows NT database for authentication?
A. This feature is available in all versions, when you use the Cisco Secure database for authentication. Versions 3.0 and later offer support of Microsoft Challenge Handshake Authentication Protocol (MS-CHAP) Version 2 and MS-CHAP Password Aging. This works with the Microsoft Dial-Up Networking client, the Cisco VPN Client (versions 3.0 and later), and any desktop client that supports MS-CHAP. This feature prompts you to change your password after a login where the password has expired. The MS-CHAP-based password-aging feature supports users who authenticate with a Windows user database and is offered in addition to password aging supported by the Cisco Secure user database. This feature is added in ACS 3.0, but it also requires device or client support. Cisco Systems is gradually adding such device or client support to various hardware.
A. Users are notified of when Cisco Secure database passwords expires on dial connections if the Cisco Secure Authentication Agent is on the PC. Once the users are in the network, they use User Changeable Password software, which runs with Microsoft IIS. When the users are on the network, they aim their browsers to the system where User Control Point (UCP) is installed and change their passwords.
A. Passwords are encrypted with the help of the Crypto API Microsoft Base Cryptographic Provider version 1.0, using the RC2 algorithm and a 40-bit key. For further information, refer to User Databases - About the Cisco Secure User Database.
Q. Default settings allow users to change their own passwords by connecting to the router via Telnet. How do I disable this option?
A. In order to prevent users from changing their passwords through Telnet, complete these steps.
- Back up the local registry.
- Go to registry key HKEY_LOCAL_MACHINE\SOFTWARE\Cisco\CiscoAAAv< your_version >\CSTacacs
- Highlight CSTacacs. Then right-click and select NEW-DWORD in order to add a registry value.
- When the new key appears on the right-hand side of the window, type disablechangepassword into the new key window.
- The default value for the new key is 0. This allows users to change the password. Right-click on the new key and select Modify. Then change the key value to 1 in order to disable the ability to change the password.
- After you add this new key, restart the CSTacacs and CSAuth services.
Q. TACACS+ Password Aging Rule does not work with SSH when Apply password change rule is set. How do I deal with this?
A. Use telnet for authentication.
TACACS+ user password changes, for example before expiry, during login do not work with SSH. Problem pertains to TACACS+ AAA server and SSH in order to establish session. This does not hold for RADIUS or telnet sessions.
TACACS+ provides a feature where if a blank password is supplied to the AAA server it triggers a password change sequence. For example, requests for old password are followed by new password. This depends upon success or failure and whether the new password is accepted or rejected.
Use telnet if password needs to be changed before expiry. For expired passwords SSH behavior is fine as it triggers a password change sequence then.
When telnetting to a router a user can just hit enter at the Password: prompt in order to initiate the change password sequence. The user can also be notified if their password is expiring or has expired. This feature does not work when you connect to the router through SSH.
A. For the step-by-step procedure to recover the password for the Cisco Secure ACS Server, refer to Password Recovery Procedure for the Cisco Secure ACS Solution Engine which explains the recovery process in detail.
A. Make sure that the software version on the ACS server and the remote agent must be the same. For example, if your ACS SE runs software version 4.1, then you must use the remote agent version 4.1 in the AD. If the software versions are not the same, the configuration will not work and you might receive this error message: External DB user invalid or bad password.
A. Complete these steps in order to remove or delete the remote agents in the ACS:
- Go to Services in the Windows server and stop the service of the ACS Agent.
- Go to the ACS and stop the login services. Choose System Configuration > login > Remote Login setup and select Do not log Remotely.
- Try to remove the remote agent. Refer to Deleting a Remote Agent Configuration for more information on deleting a remote agent.
Q. When remote agents are added to the ACS, this error occurs: Failed to commit all Fields. How can I resolve this error?
A. The Failed to commit all Fields error message often occurs when a patch is not installed correctly or is corrupted. Re-imaging the ACS and restoring the configuration resolves the error.
A. From the command line, issue the net stopcsauth command in order to stop the service on each server. Then issue the csauth -z -p command in order to run both the source and the target in debug, and look for messages in the window. The output also goes into the $BASE\CSAuth\Logs\auth.log file. Often one or more of the authentication, authorization, and accounting (AAA) servers is misconfigured. Therefore, look for messages on the target that report requests from illegal or unknown hosts. If the source has several network adapters, then it causes the target to see the wrong IP address and reject the source as unknown.
Q. I use ACS with servers in geographically dispersed areas, and services are disrupted when I replicate. How do I deal with this?
A. Ensure that the authenticating devices are configured for failover. In other words, ensure there are at least two servers defined in order to provide backup if one server is unreachable. (This is a good idea whether replication is involved or not.) For example, if the arrangement has one ACS in the U.S. that replicates to a second ACS in Australia, configuring the authenticating devices to try the U.S. then Australia is probably not the best plan. Install a second local server (in the U.S.) and replicate it from the U.S. master to the U.S. slave. The U.S. slave then replicates to the Australia slave.
A. No, they are native syslog.
A. For each CSV log, Cisco Secure ACS writes a separate log file. When a log file reaches 10 MB in size, Cisco Secure ACS starts a new log file. Cisco Secure ACS retains the most recent 7 log files for each CSV log. For more information on generating a log, refer to Enabling or Disabling a CSV Log.
A. Either disable Network Access Restrictions (NAR) or completely configure it for use.
Q. When I set up authentication, I receive the Chpass is currently disabled. error when I try to authenticate. How do I resolve this issue?
A. The user account password must be set to change on login. In order to change the password, select System Configuration > Local Password Management > Disable TELNET Change Password against this ACS and return the following message to the users Telnet session "Chpass is currently disabled." and uncheck the box. This allows you to change the password.
Q. When I attempt to download the database with the csutil.exe -d command, it results in the error message "Failed to initialize crypto API". What does this mean?
A. You receive this error message when you log into a Cisco Secure ACS Server with an account other than the local admin account. This causes the inability of the csutils command to run.
Another cause for this error is that the passwords and AAA keys in the ACS database are encrypted with the help of the Microsoft Crypto API. Only local administrators and the actual system are able to access the important information needed in order to decrypt these passwords and keys.
Q. When I attempt to upgrade from Cisco Secure ACS for Windows 3.0.3 to 3.2, I receive the "ACS FOLDER IS LOCKED BY ANOTHER APPLICATION" error message. What do I need to do?
A. Complete these steps.
- Run the Filemon utility in order to check for any "sharing violations" while you try the installation.
Note: Do not use terminal services in order to upgrade and disable the service temporarily.
- Change the System Configuration > Service Control > Manage Directory to only keep the last seven files.
Q. When I try to bring up the GUI, I get an Invalid administration control error. The installation is successful, and the services run. What is the problem?
A. This problem is usually seen when the browser has a proxy server configured. In order to fix this, disable the proxy server completely and then bring up the ACS administration screen.
Q. I see odd things in the ACS GUI. For example, the same users appear in multiple groups and I cannot delete users from the database. How do I fix this kind of corruption?
A. Complete these steps in order to add a user:
- Add a new record to the end of the file.
- Create an index path to the new record.
If there is an interruption of the CSAuth services during this process, it is possible that the record is in the database. However, it cannot be edited because it uses a lookup through the indexing code.
In order to clean up the database, go into the command line and issue the $BASE\utils\csutil -q -d -n -l dump.txt command.
$BASE is the directory where the software is installed. This command causes the database to be unloaded and reloaded in order to clear up the counters.
Q. I cannot start services for RADIUS after I re-install the software several times. The event error says that service was terminated with service specific error 11.
A. There are several different reasons why you are not able to start the CSRadius service. The most common problem is running Windows with an unsupported service pack, or there is software contention with another application. Supported platforms and service packs are specified in the installation documentation.
In order to check for port conflicts, go to the command line of the server and issue the netstat -an | findstr 1645 and netstat -an | findstr 1644 commands to see if any other service uses these User Data Protocol (UDP) ports. If another service uses these ports, you see something similar to this output:UDP 0.0.0.0:1645 *:* UDP 0.0.0.0:1646 *:*
Another possible cause of the error message is that Microsoft Server services probably has not started. In order to check this, select Control Panel > Services and ensure that the Server service options for Started and Automatic are selected.
Q. The ACS installation fails and I see an error about NSLDAPSSL32V30.dll that says it cannot overwrite the file. What causes this and how do I resolve the error?
A. This error can be caused by contention with an installation of Cisco Secure VPN Client version 1.1. Resolve the conflict with the removal of the VPN Client from the system.
A. The reason for this issue is the external Windows database is a 64-bit operating system. ACS products with ACS version prior to 4.2.1 do not work with the 64-bit operating system. In ACS version 4.2.1 and later the 64 bit operating system is supported and hence you are able to connect the ACS Solution Engine (SE) with an external Windows database.
A. You cannot directly edit this attribute because the ACS GUI already has an option on how to set this value.
Within the "IP address assignment" section of the group editing, you have three options: "no ip address assignment", "assigned by dialup client", and "Assigned from AAA client pool". There is a fourth option, "Assigned from AAA server pool", if you have the pools assigned.
You need to use the third option ("Assigned from AAA client pool"). Setting this and then setting the name of the pool will return this value in attribute 88. User-side settings have these options if you need this to be configured at a per-user level. Also, you need to set the AAA client to authenticate using RADIUS (IETF).
A. No tools are supplied with ACS. For additional information, see Does Cisco recommend a software application that can be used to report on accounting logs available in ACS?
Q. The ACS has been reconfigured to require a user name and password to log in locally. Now everyone is locked out. How do I fix this?
A. The solution to this problem depends on the version of software in place. No matter what software version you have, be sure to back up the NT registry first.
In early versions of ACS, the user name and password requirement for local login is modified in the registry. Issue the regedit command and search for allow AutoLocalLogin. Change the registry value to 1 in order to allow local login, and then recycle the services.
In ACS versions 2.6 and later, issue the regedit command and remove the users in this location:HKEY_LOCAL_MACHINE\SOFTWARE\Cisco\CiscoAAA##\CSAdmin\Administrators
Under the Administrators key, see all the administrators that you have created. Delete the users and exit the registry. When you access ACS, you are not prompted for a user name and password. Once you are in the GUI, add administrators.
Q. The ACS documentation chapter on Cisco Secure ACS Command-Line Database utility explains how to bulk import a large number of users into ACS with the csutil -i command. How do I bulk import network access servers (NASes)?
A. The procedure used to bulk import NASes is similar to the import of users. This flat-file is an example:ONLINE ADD_NAS:sam_i_am:IP:10.31.1.51:KEY:cisco:VENDOR:CISCO_T+ ADD_NAS:son_of_sam:IP:10.31.1.52:KEY:cisco:VENDOR:CISCO_R
The NASes can also be imported into a particular Network Device Group. This flat-file is an example:ADD_NAS:koala:IP:10.31.1.53:KEY:cisco:VENDOR:CISCO_R:NDG:my_ndg
A. For more information, refer to Q & A for Cisco Secure ACS Version 3.2 for Windows 2000 and NT.
A. If you select NDS Server Support, complete these steps:
- See your Novell NetWare administrator in order to get the names and other information for the tree, container, and context.
- Click NDS Server Support.
- Enter a name for the configuration. This name is for informational purposes only.
- Enter the tree name.
- Enter the full context list, separated by dots (.). Separate multiple context lists with a comma and space. For example, if your organization is Corporation, your organization name is Chicago, and you want to enter two context names (Marketing and Engineering), enter this information:You do not need to add users in the context list.Engineering.Chicago.Corporation, Marketing.Chicago.Corporation
- Click Submit. Changes take effect immediately. You do not need to restart the ACS.
Caution: If you click Delete, your NDS database settings are deleted.
A. There are two ways you can use in order to check the release.
When you bring up the browser, look for this at the bottom of the page:Cisco Secure ACS v2.3 for Windows NT Release 2.3(2)
Bring up the DOS prompt on the Cisco Secure machine and run:D:\Program Files\Cisco Secure ACS v2.3\Utils>csutil CSUtil v2.3(2.4), Copyright 1997, Cisco Systems Inc.
A. In order for the Logged In Users report to work (this also applies to most other features that involve sessions), packets need to include at least these fields:
Authentication Request packetnas-ip-address nas-port
Accounting Start packetnas-ip-address nas-port session-id framed-ip-address
Accounting Stop packetnas-ip-address nas-port session-id framed-ip-address
Attributes (such as nas-port and nas-ip-address) that appear in multiple packets need to contain the same value in all packets.
If a connection is so brief that there is little time between the start and stop packets (for example, HTTP through the PIX), then logged-in users do not work.
ACS versions 3.0 and later allow the device to send either nas-port or nas-port-id.
Q. When I access the ACS GUI through a firewall, the address for the server in the URL field changes from a global IP address to a local address. Why does this happen?
A. In the current version of ACS 3.0, this problem has been addressed. The global IP address does not change when you change to subsequent pages after the initial login.
A. No. A user cannot be in more than one group at a time.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.