Document ID: 113397
This document provides a sample configuration and verification for the Link Layer Discovery Protocol (LLDP) features on the Catalyst 3750/3750-E/3750-X Series Switches. Specifically, this document shows you how to configure the port-based traffic control features on a Catalyst 3750 switch.
Make sure that you meet these requirements before you attempt this configuration:
Have basic knowledge of configuration on Cisco Catalyst 3750/3750-E/3750-X Series Switches
Have basic understanding of LLDP features
The information in this document is based on Cisco Catalyst 3750 Series Switches.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
LLDP is a neighbor discovery protocol that allows non-Cisco devices to advertise information about themselves to other devices on the network. Cisco switches supports the IEEE 802.1AB LLDP which allow non-Cisco devices for interoperability between other devices. LLDP runs over the data-link layer which allows two devices running different network layer protocols to learn about each other.
LLDP discovers neighbor devices by using a set of attributes that contain type, length, and value descriptions. These attributes are referred to as TLVs. LLDP supported devices can use TLVs to receive and send information to their neighbors. This protocol can advertise details such as configuration information, device capabilities, and device identity.
The switch supports these basic management TLVs, which are mandatory LLDP TLVs:
Port description TLV
System name TLV
System description TLV
System capabilities TLV
Management address TLV
These organizationally-specific LLDP TLVs are also advertised to support LLDP-MED:
Port VLAN ID TLV (IEEE 802.1 organizationally specific TLVs)
MAC/PHY configuration/status TLV (IEEE 802.3 organizationally-specific TLVs)
In this section, you are presented with the information needed to configure the LLDP features described in this document.
This document uses this network setup:
This document uses these configurations:
|Catalyst 3750 Switch|
Switch#configure terminal !--- Enable LLDP globally on the switch. Switch(config)#lldp run !--- Specify time for the device to hold LLDP information. Switch(config)#lldp holdtime 180 !--- Set the time for sending frequency of LLDP updates. Switch(config)#lldp timer 50 !--- Enable LLDP specific to an interface. Switch(config)#interface gigabitethernet 1/0/1 !--- Enable the interface to send LLDP. Switch(config-if)#lldp transmit !--- Enable the interface to receive LLDP. Switch(config-if)#lldp receive !--- Return to privileged EXEC mode. Switch(config-if)#end !--- Save the configurations in the device. switch(config)#copy running-config startup-config Switch(config)#exit !--- Disable LLDP feature on the switch. Switch(config)#no lldp run Switch(config)#end
Use this section to confirm that your configuration works properly.
Use the show lldp interface [interface-id] command in order to display information about interfaces with LLDP enabled.
Switch#show lldp interface gigabitethernet1/0/1 GigabitEthernet1/0/1: Tx: enabled Rx: enabled Tx state: IDLE Rx state: WAIT FOR FRAME
Use the show lldp neighbors command in order to display information about neighbors.
Switch#show lldp neighbors Capability codes: (R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device (W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other Device ID Local Intf Hold-time Capability Port ID Nortel IP Phone Gi1/0/1 180 T 0019.e1e7.018d Polycom SoundPoint IGi1/0/19 180 T 0004.f22f.88b7 Baseline Switch 2426Gi1/0/18 180 P,B Ethernet0/26 Baseline Switch 2426Gi1/0/22 180 P,B Ethernet0/26 Total entries displayed: 4
Use the show lldp neighbors detail command in order to display information about neighbors in detail.
Switch#show lldp neig detail Chassis id: 22.214.171.124 Port id: 0019.e1e7.018d Port Description: Nortel IP Phone System Name - not advertised System Description: Nortel IP Telephone 1230E, Firmware:062AC53 Time remaining: 166 seconds System Capabilities: B,T Enabled Capabilities: T Management Addresses - not advertised Auto Negotiation - supported, enabled Physical media capabilities: Other/unknown 10base-T(HD) Symm Pause(FD) Symm, Asym Pause(FD) 1000baseX(FD) 1000baseT(HD) Media Attachment Unit type: 16 MED Information: MED Codes: (NP) Network Policy, (LI) Location Identification (PS) Power Source Entity, (PD) Power Device (IN) Inventory F/W revision: 062AC53 Manufacturer: Nortel-05 Model: IP Phone 1230E Capabilities: NP, LI, PD, IN Device type: Endpoint Class III Network Policy(Voice): Unknown PD device, Power source: Unknown, Power Priority: High, Wattage: 6.0
Use the show lldp traffic command in order to display LLDP counters.
Switch#show lldp traffic LLDP traffic statistics: Total frames out: 560 Total entries aged: 0 Total frames in: 211 Total frames received in error: 0 Total frames discarded: 0 Total TLVs discarded: 208 Total TLVs unrecognized: 208
Use the show lldp errors command in order to display LLDP error counters.
Switch#show lldp errors LLDP errors/overflows: Total memory allocation failures: 0 Total encapsulation failures: 0 Total input queue overflows: 0 Total table overflows: 0
- Cisco Catalyst 3750 Series Switches Support Page
- Cisco Catalyst 3750-E Series Switches Support Page
- Cisco Catalyst 3750-X Series Switches Support Page
- Switches Product Support
- LAN Switching Technology Support
- Technical Support & Documentation - Cisco Systems
|Updated: Jan 23, 2012||Document ID: 113397|