Table Of Contents
Data Sheet
Key Features and Benefits
Hardware and Software Features
Channelization Features
Encapsulation
DS-1 Features
E1 Features
DS-3 Features
SONET and SDH Features
Other
Features Not Supported
Physical Specifications
Environmental Specifications
Product Regulatory Compliance
Environmental Conditions
Product Regulatory Approvals
Laser Safety
Electromagnetic Emissions Certification
Immunity
Network Equipment Building Systems
Connector
LEDs
Network Management
Power Budget
Optical Power Budget
Hardware Requirements
Software Requirements
Ordering Information
Service and Support
Data Sheet
Cisco 10000 Series Four-Port
Channelized STM-1/OC-3 Line Card
The Cisco 10000 Series Four-Port Channelized STM-1/OC-3 Line Card offers service providers the combined advantages of industry-leading DS1/E1 density, low cost per port, flexible provisioning options and high reliability for their edge aggregation applications.
Figure 1
Cisco 10000 Series Four-Port Channelized STM-1/OC-3 Line Card
Designed for telcos and service providers (SPs), this line card supports four channelized STM-1/OC-3 ports with maximum DS3/DS1/DS0/64K flexibility in both a SONET and SDH environment.
Key Features and Benefits
Designed for concentrating IP access over telco time-division multiplexing (TDM) networks, the Cisco 10000 Series channelized STM-1/OC-3 line card has the following key features and benefits.
•
Provides industry-leading density per rack, enabling service providers to scale networks cost-effectively.
•Supports any combination of DS-0/64 kbps, fractional T-1/E-1, and DS-3 for maximum flexibility.
•Supports service-transparent online insertion and removal (OIR), allowing line cards to be removed without impacting traffic.
•Supports SONET automatic protection switching (APS) and SDH Multiplex Section Protection (MSP), valuable tools for supporting network resiliency, fault tolerance, and increased overall network availability. APS and MSP provide very fast Layer 1 switch over mechanism to support 1:1 redundant transmission circuits. They allow rapid switchover from one fiber connection to another in the event of a fiber cut, module failure, signal failure, or signal degradation. The result is increased network resiliency, minimal loss of data, and reduction in time-consuming data reroutes.
Hardware and Software Features
•Four-port channelized STM-1/OC-3
•Single-mode (intermediate reach) LC optics at 1330 nm
•IP supported
•Online Insertion and Removal (OIR)
•1:1 SONET Automatic Protection Switching (APS) and SDH Multiplex Section Protection (MSP)
Channelization Features
•NxDS0 (Each DS1 and E1 may be further channelized into NxDS0 channels)
•Channelization to DS0 (56K or 64K), including multiple channel groupings per DS1 and fractional DS1
•DS1 clearchannel and fractional; Framed
•E1 clearchannel and fractional; Framed and unframed
•J1 support
•Unchannelized and channelized DS3 (28xDS1)
•DS3 Subrate & Scrambling; Interoperable with Kentrox, Digital Link, Larscom, Verilink and Adtran.
•Supports up to 768 channels per card with any mixture of DS3, nxDS1, or nxDS0 with the following restrictions:
–192 channels per port
–Total number of channels does not exceed chassis scaling limits
•Channelization to DS1 (SONET)
–Support for SONET Virtual Tributary 1.5 (VT1.5) mapping: STS-3 <-> STS-1 <-> VT1.5 <-> DS-1
–Support for asynchronous DS3 channelized down to DS-1 (M13 and C-bit framing) mapped into: STS-3 <-> STS-1 <-> DS-3 <-> DS-1
•Channelization to DS1 (SDH)
–STM-1 <-> AU-4 <-> TUG-3 <-> TUG-2 <-> TU-11 <-> <-> DS-1
–STM-1 <-> AU-3 <-> TUG-2 <-> TU-11 <-> DS-1
•Channelization to E1 (SONET)
–Support for SDH Virtual Tributary 2 (VT2) mapping: STS-3 <-> VT2 <-> E-1
•Channelization to E1 (SDH)
–Support for ITU-T G.707 (SDH CEPT/ETSI) Virtual Container 12 (VC-12) mapping: STM-1 <-> AU-4 <-> TUG-3 <-> TUG-2 <-> TU-12 <-> VC-12 <-> E-1
–STM-1 <-> AU-3 <-> TU-2 <-> TU-12 <-> E-1
•Channelization to J1
–Support for ITU-T G.707 (SDH-ANSI) Virtual Container 11 (VC-11) mapping: STM-1 <-> AU-3 <-> TUG-2 <-> TU-11 <-> VC-11 <-> J1
•Channelization to DS3 (SONET)
–STS-3 <-> STS-1 <-> DS-3
•Channelization to DS3 (SDH)
–STM-1 <-> AU-3 <-> DS-3
Encapsulation
•Frame Relay
•Point-to-Point Protocol (PPP)
•Cisco HDLC (support for shared flags, configurable IDLE pattern, and 16- or 32-bit cyclic redundancy check (CRC))
DS-1 Features
•Superframe (SF) and Extended Superframe (ESF) support
•Internal or line-derived (loop) clocking, independently selectable on each T-1 tributary
•Error and alarm detection: CRC errors, framing errors, loss of frame (red), AIS (blue), remote alarm indication (yellow)
•Alarm reporting-24-hour history maintained, 15-minute intervals on all errors
•BERT at DS-1 level
•Loopback capabilities: local, network line and network payload, remote network line and remote network payload at the T-1 level
•ANSI T1.403 facility data link (FDL) on ESF mode DS1s and ATT 54016 FDL mode, responses only
•Local and remote performance monitoring
•Response to embedded remote loopback commands - BOC (bit oriented commands)
•Detect and insert embedded remote loopback commands - BOC (bit oriented commands)
–AIS
–RDI
–Loss of signal and loss of frame (near end and far end)
–Loss of multiframe (LOMF)
–Local and network line loopback
E1 Features
•Framing: CRC-4 and no-CRC-4 conformance with ITU-T G.704
•Internal or line-derived (loop) clocking, independently selectable on each E-1 tributary
•Error and alarm detection: CRC errors, framing errors, loss of frame, AIS, remote alarm indication
•Performance monitoring: 24-hour history retained; 15-minute intervals on all errors
•BERT at E-1 level
•Line and payload loopback capabilities-local and network line, and network payload at the E-1 level
DS-3 Features
•Channelized, clearchannel or subrate
•C-bit parity or M23 framing
•FEAC channel support
•BERT at DS-3 level
•Internal or line-derived (loop) clocking
•Error and alarm detection: CRC errors, framing errors, loss of frame (red), AIS (blue), remote alarm indication (yellow)
•Alarm reporting-24-hour history maintained, 15-minute intervals on all errors
•Loopback capabilities: local, network line and network payload, remote network line and remote network payload
•Local and remote performance monitoring
•Response to embedded remote loopback commands - BOC (bit oriented commands)
•Detect and insert embedded remote loopback commands - BOC (bit oriented commands)
–AIS
–RDI
–Loss of signal and loss of frame (near end and far end)
–Loss of multiframe (LOMF)
–Local and network line loopback
SONET and SDH Features
•Compliance with G.707, G.783, G.784, G.957, G.958, GR-253, as applicable
•Synchronization Local (internal) or loop timed (recovered from network)
•Local (diagnostic) and line (network) loopback
•Alarm processing-Receive and transmit alarm processing. See Table 1 for supported alarm and signal events.
•Statistics-Performance and error counts
•TX path trace
•RX path trace
•Payload scrambling
•Internal or line (as recovered from the network) clocking modes
•Local (diagnostic) and network (line) loopback modes
•SONET APS and SDH MSP, 1+1 unidirectional
•Detect and alarm
–AIS
–RDI
–Remote failure indicator
–Loss of signal and loss of frame
–Loss of pointer
Table 1
Supported SONET/SDH Alarm and Signal Events Alarm/Signa
| |
SONET Description
|
SDH Description
|
B1-TCA
|
B1 BER Threshold Crossing Alarm
|
B1 BER Threshold Crossing Alarm
|
B2-TCA
|
B2 BER Threshold Crossing Alarm
|
B2 BER Threshold Crossing Alarm
|
B3-TCA
|
B3 BER Threshold Crossing Alarm
|
B3 BER Threshold Crossing Alarm
|
LAIS
|
Line Alarm Indication Signal (AIS-L)
|
Multiplexer Section Alarm Indication Signal (MS-AIS)
|
LOM
|
Loss of Multiframe VT (LOM-V)
|
Loss of Multiframe (LOM)
|
LRDI
|
Line Remote Defect Indication (RDI-L)
|
Multiplexer Section Remote Defect Indication (MS-RDI)
|
PAIS
|
Path Alarm Indication Signal, or Alarm Indication Signal-Path (AIS-P)
|
Administrative Unit Alarm Indication Signal (AU-AIS)
|
PLM
|
Path Payload Label Mismatch, or Payload Label Mismatch-Path (PLM-P)
|
High Order Path Payload Label Mismatch (HP-PLM)
|
PLOP
|
Path Loss of Pointer, or Loss of Pointer-Path (LOP-P)
|
Administrative Unit Loss of Pointer (AU-LOP)
|
PRDI
|
Path Remote Defect Indication, or Remote Defect Indication-Path (RDI-P)
|
High Order Path Remote Defect Indication (HP-RDI)
|
PUNEQ
|
Path Unequipped (UNEQ-P)
|
High Order Path Unequipped (HP-UNEQ)
|
SD-BER
|
Line BIP BER in excess of the Signal Degrade (SD) threshold
|
Multiplexer Section BIP BER in excess of the Signal Degrade (SD) threshold
|
SF-BER
|
Line BIP BER in excess of the Signal Fail (SF) threshold
|
Multiplexer Section BIP BER in excess of the Signal Fail (SF) threshold
|
SLOF
|
Section Loss of Frame (LOF)
|
Regenerator Section Loss of Frame (LOF)
|
SLOS
|
Section Loss of Signal (LOS)
|
Regenerator Section Loss of Signal (LOS)
|
Other
•Bit error rate testing (BERT)
•Loopback capabilities: local and network at the OC-3/STM-1 level
•Dynamic Provisioning on each physical port.
•Scrambling and subrate can be independently or simultaneously enabled in each DSU mode.
Features Not Supported
•OC-3c, STM-1c
•Unframed DS-3 (HSSI)
•DS-2 loopbacks, alarms, performance monitoring, or Management Information Base (MIB) support
•DS-1 signaling
•E-1 time slot 16 (TS16) signaling multiframe
•E-1 Bit Oriented Protocol (BOP)
•E-1 remote loopback
•SONET and SDH on the same card (all ports have to be either all SONET or all SDH)
•E-1 and DS-1 on the same port
Physical Specifications
•Weight: 4.75 lb (2.16 kg)
•Dimensions: 16.0 x 1.12 x 9.97 in. (40.64 x 2.83 x 25.32 cm) (H x W x D)
Environmental Specifications
•Storage temperature: -38° to 150°F (-40° to 70°C)
•Operating temperature, nominal: 41° to 104°F (5° to 40°C)
•Operating temperature, short term: 23° to 131° (-5° to 55°C)
•Storage relative humidity: 5% to 95% relative humidity (RH)
•Operating humidity, nominal: 5% to 85% RH
•Operating humidity, short term: 5% to 90% RH
•Operating altitude: -60 m to 4000 m
Product Regulatory Compliance
Environmental Conditions
•Storage temperature: -38 to 150°F (-40 to 70°C)
•Operating temperature, nominal: 41 to 104°F (5 to 40°C)
•Operating temperature, short term: 23 to 131°F (-5 to 55°C)
•Storage relative humidity: 5 to 95% relative humidity (RH)
•Operating humidity, nominal: 5 to 85% RH
•Operating humidity, short term: 5 to 90% RH
•Operating altitude: -60 to 4000m
Product Regulatory Approvals
•UL60950/CAN/CSA-C22.2 No. 60950-00, third edition, dated December 1, 2000, with no deviation considered to be less stringent than IEC 60950
•EN60950 with Amendments 1-4, for CE Marking to the LVD directive
•IEC 60950 third edition with Amendments 1-4, including all national/group deviations
•AS/NZS 60950:2000
•AS/NZS 3260-1993 with Amendments 1-4
•ACA TS001-1997
Laser Safety
•21 CRF 1040, Subchapter J
–EN60825-1
–EN60825-2
Electromagnetic Emissions Certification
•AS/NZ 3548:1995 (including Amd I + II) Class B
•EN55022:1998 Class B
•CISPR 22:1997
•EN55022:1994 (including Amd I+ II)
•47 CFR Part 15:2000 (FCC) Class B
•VCCI V-3/01.4 Class 2
•CNS-13438:1997 Class B
•GR1089:1997 (including Rev1: 1999)
Immunity
•EN300386:2000—TNE EMC requirements; product family standard; high priority of service; central office and non-central office locations
•EN50082-1:1992/1997
•EN50082-2:1995—Generic Immunity Standard, Heavy Industrial
•CISPR24:1997
•EN55024:1998—Generic ITE Immunity Standard
•EN61000-4-2:1995+AMD I + II-ESD, Level 4, 8-kV contact,15-kV air
•IEC-1000-4-3:1995+AMD 1—Radiated Immunity, 10 V/m
•IEC-1000-4-4:1995—Electrical Fast Transients, Level 4, 4 kV/B
•IEC-1000-4-5:1995+AMD 1—DC Surge Class 3; AC surge Class 4
•EN61000-4-6:1996+AMD 1—RF Conducted Immunity, 10V rms
•EN61000-4-11:1995—Voltage Dips and Sags
•ETS300 132-2:1996+corregendum, Dec. 1996
•GR1089:1997 (including Rev1: 1999)
Network Equipment Building Systems
•Level 3 compliant
•Telcordia SR-3580 Criteria Levels, issued November 1995
•GR1089-Core: Electromagnetic Compatibility & Electrical Safety, issued February 1999
•GR63-Core: Physical Protection Requirements, issued April 2002
•SBC equipment requirements: TP76200 MP and TP76400 MP
•Verizon equipment requirements: SIT.NEBS.TE.NPI.2002.010
Connector
•LC duplex connector, single-mode, intermediate-reach optics
LEDs
•Line card fail (Fail)—A single yellow LED that is set OFF when the board is working properly
•Carrier Detect (1 per STM-1/OC-3, 4 per card) (CA)—A green LED turned on when a carrier is detected on the port; it is the logical inverse of loss of signal (LOS)
•Alarm (1 per STM-1/OC-3, 4 per card) (Alarm)—A yellow LED; during normal operation, this LED is on to indicate the presence of any alarm condition on any provisioned controller/interface at OC-3/STM-1, DS3, E1, or DS1 levels
•Loopback active (1 per STM-1/OC-3, 4 per card) (LOOP)—A yellow loopback active LED used as an external indication that any portion of the data path is in a loopback state and not enabled for normal data traffic
Network Management
•Network Management via
–Telnet (CLI)
–Console port (CLI)
–Simple Network Management Protocol (SNMP)
Power Budget
•Unit Power: 75W max, 50W typ
Optical Power Budget
•Power budget: 12db
•Transmit power: -15 to -8 dBm
•Receive power: -28 to -8 dBm
•Typical maximum distance: 9.3 miles (15 km)
Hardware Requirements
•Chassis—The 4-port CHSTM-1/OC-3 line card is supported on all Cisco 10000 Series chassis
•Performance routing engines (PREs)—The 4-port CHSTM-1/OC-3 line card is supported on all PREs available on the Cisco 10000 Series
Software Requirements
Initial IOS Releases (PRE1): The 4-port CHSTM-1/OC-3 line card is supported in 12.0(15)SL, 12.0(17)ST, 12.0(22)S, 12.2(8)BZ and later Cisco IOS® releases for SDH mode. For both SONET and SDH mode, the 4-port CHSTM-1/OC-3 line card is supported in 12.0(23)S and later Cisco IOS releases.
Initial IOS Releases (PRE2): For both SONET and SDH mode, the 4-port CHSTM-1/OC-3 line card is supported in 12.2(15)BX and later Cisco IOS releases.
For the latest IOS release information, refer to:
http://www.cisco.com/pcgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi.
Ordering Information
Part Number
|
Description
|
ESR-4OC3-ChSTM-1/OC-3
|
Four-port channelized STM-1/OC-3 SDH single mode line card
|
ESR-4OC3-ChSTM-1/OC-3=
|
Four-port channelized STM-1/OC-3 SDH single mode, spare
|
Service and Support
Cisco Systems offers a wide range of service and support options for its customers. More information on Cisco service and support programs and benefits can be found a:
http://www.cisco.com/en/US/support/index.html
