Guest

Cisco 10000 Series Routers

Cisco 10000 Series Four-Port OC-3/STM-1c ATM Line Card

Table Of Contents

Data Sheet

Key Benefits

ATM Features

Packet Layer Features

High-Availability Features

Hardware Features

Physical Specifications

LEDs

Product Regulatory Compliance
Environmental Conditions

Product Regulatory Approvals

Laser Safety

Electromagnetic Emissions Certification

Immunity

Network Equipment Building Systems

ATM Standards

Network Management

Power Budget

Optical Power Budget

Hardware Requirements

Software Requirements

Ordering Information

Service and Support


Data Sheet


Cisco 10000 Series Four-Port

OC-3/STM-1c ATM Line Card

The Cisco 10000 Series Four-Port OC-3c/STM-1c Asynchronous Transfer Mode (ATM) line card provides both the performance and the density to scale networks efficiently and reliably. It features a high-performance segmentation and reassembly (SAR), adapted for various applications including advanced traffic management, cell scheduling, and integrated buffer management. By mapping IP class of service (CoS) to ATM quality of service (QoS) on the Cisco 10000 Series ATM line cards, the flow of mission-critical data can be effectively managed across heterogeneous IP and ATM networks.

Figure 1

Cisco 10000 Series Four-Port OC-3/STM-1c ATM Line Card

Key Benefits

Line-rate OC-3c/STM-1c performance—The OC-3c/STM-1c ATM module is a standards-based ATM solution supporting line-rate (155-Mbps) performance at 64-byte packets that allows Internet service providers (ISPs) to offer line-rate Internet access via ATM virtual circuits.

Per-virtual circuit and per-virtual path traffic shaping—The Cisco 10000 Series OC-3c/STM-1c ATM Module supports both per-virtual circuit and per-virtual path traffic shaping, providing flexibility and control over every virtual circuit and virtual path configured. Per-virtual circuit and per-virtual path traffic shaping allows bursts of traffic to conform to a predetermined contract, ensuring that excessive traffic from one virtual circuit does not incur data loss on other virtual circuits. This function is very important when connecting to an ATM WAN or public ATM network, where ATM switches may discard excessive traffic at the point of ingress.

Standards-based ATM implementation for interoperability—The OC-3c/STM-1c ATM module is a standards-based ATM interface, allowing customers to integrate the Cisco 10000 Series into existing ATM networks. By implementing a standards-based version of ATM, Cisco ensures that customers will be able to easily and quickly integrate the Cisco 10000 Series into their current ATM network. Further, by using standard Operations, Administration, and Management (OA&M) F4 and F5, customers will enjoy lower management and administrative expenses and improved overall manageability.

ATM Features

Supports ATM Forum traffic management service categories: non-real time variable bit rate (nrt-VBR) and universal bit rate (UBR)

Supports User-Network Interface (UNI) Versions 3.0 and 3.1

Supports Integrated Local Management Interface (ILMI) permanent virtual circuit (PVC) autodiscovery feature

Supports up to 32,000 PVCs per module; up to 61,500 PVCs per platform; up to 32,000 UBR PVCs; up to 2000 nrt-VBR PVCs on the leased-line Cisco IOS® trains, beginning with Version 12.0(20)ST; up to 61,500 virtual circuits per platform; up to 8000 virtual circuits per port on the broadband aggregation Cisco IOS trains, beginning with Version 12.2(15)BX

Offers full support for virtual path identifier (VPI) and virtual circuit identifier (VCI) address width (16-bit VCI, 8-bit VPI)

Supports PVCs and permanent virtual path (PVPs)

Supports per-virtual circuit queuing and shaping for nrt-VBR

Supports Class-Based Weighted Fair Queuing (CBWFQ) and Priority Queuing for nrt-VBR virtual circuits

Offers RFC 1483 support for routed protocols

Offers RFC 2684 support for ATM adaption layer 5 (AAL5) Logical Link Control (LLC)/subnetwork attachment point Subnet Access Protocol (SNAP) encapsulations and AAL5 Mux IP Version 4 encapsulation

Supports PVCs over AAL5

Supports call admission control (does not allow configuration of nrt-VBR PVCs if requested bandwidth is not available on the port)

Supports OA&M F4/F5 segment and end-to-end loopback

Supports OA&M management (allows management of PVCs using this feature via OA&M)

Supports SONET/SDH OC-3 STS-3c/STM-1c framing format

Packet Layer Features

Supports all IP routing protocols

Supports application of QoS (Priority Queuing/CBWFQ, Weighted Random Early Detection [WRED], committed access rate [CAR]) to each nrt-VBR PVC, and to all UBR PVCs as a group using Cisco modular command-line interface (CLI)

Supports ATM cell loss priority (CLP) bit

Supports multicast

Supports access control lists (ACLs)

Supports Multiprotocol Label Switching (MPLS)

Frame mode MPLS over ATM

MPLS Cell mode with LC-ATM support. This value-added feature allows service providers with existing ATM backbone to upgrade their switches with label switch controller to support the MPLS control plane. It is a great value proposition, enabling new services to be provisioned over the infrastructure while protecting the investment.

Supports turbo QoS classification, NetFlow accounting, 802.1Q VLAN, policy-based routing, per-packet load balancing, and generic routing encapsulation (GRE) tunneling

High-Availability Features

Supports 1+1 redundancy per port line card using automatic protection switching (APS)

Supports 1+1 line-card redundancy for card failover

Supports online insertion and removal (OIR)

Supports Cisco IOS Software Route Processor Redundancy Plus (RPR+)

Supports alarms (SONET-based alarms)

Hardware Features

Occupies a single slot in the Cisco 10000 Series chassis; full-height line card

LC connector

Interface: single mode, intermediate reach

Hot-swappable, no slot dependency

Network Equipment Building Systems (NEBS) Level 3 compliant

Physical Specifications

Weight: 4.75 lb (2.16 kg)

Dimensions (H x W x D): 16.0 x 1.12 x 9.97 in. (40.64 x 2.83 x 25.32 cm)

LEDs

Carrier status (green, one per card)

Loopback (yellow, one per card)

Alarm (yellow, one per card)

Enable (green, one per card)

Fail (yellow, one per card)

Product Regulatory Compliance
Environmental Conditions

Storage temperature: -38 to 150°F (-40 to 70°C)

Operating temperature, nominal: 41 to 104°F (5 to 40°C)

Operating temperature, short term: 23 to 131°F (-5 to 55°C)

Storage relative humidity: 5 to 95% relative humidity (RH)

Operating humidity, nominal: 5 to 85% RH

Operating humidity, short term: 5 to 90% RH

Operating altitude: -60 to 4000m

Product Regulatory Approvals

UL60950/CAN/CSA-C22.2 No. 60950-00, third edition, dated December 1, 2000, with no deviation considered to be less stringent than IEC 60950

EN60950 with Amendments 1-4, for CE Marking to the LVD directive

IEC 60950 third edition with Amendments 1-4, including all national/group deviations

AS/NZS 60950:2000

AS/NZS 3260-1993 with Amendments 1-4

ACA TS001-1997

Laser Safety

21 CRF 1040, Subchapter J

EN60825-1

EN60825-2

Electromagnetic Emissions Certification

AS/NZ 3548:1995 (including Amd I + II) Class B

EN55022:1998 Class B

CISPR 22:1997

EN55022:1994 (including Amd I+ II)

47 CFR Part 15:2000 (FCC) Class B

VCCI V-3/01.4 Class 2

CNS-13438:1997 Class B

GR1089:1997 (including Rev1: 1999)

Immunity

EN300386:2000—TNE EMC requirements; product family standard; high priority of service; central office and non-central office locations

EN50082-1:1992/1997

EN50082-2:1995—Generic Immunity Standard, Heavy Industrial

CISPR24:1997

EN55024:1998—Generic ITE Immunity Standard

EN61000-4-2:1995+AMD I + II—ESD, Level 4, 8-kV contact,15-kV air

IEC-1000-4-3:1995+AMD 1—Radiated Immunity, 10 V/m

IEC-1000-4-4:1995-Electrical Fast Transients, Level 4, 4 kV/B

IEC-1000-4-5:1995+AMD 1—DC Surge Class 3; AC surge Class 4

EN61000-4-6:1996+AMD 1—RF Conducted Immunity, 10V rms

EN61000-4-11:1995—Voltage Dips and Sags

ETS300 132-2:1996+corregendum, Dec. 1996

GR1089:1997 (including Rev1: 1999)

Network Equipment Building Systems

Level 3 compliant

Telcordia SR-3580 Criteria Levels, issued November 1995

GR1089-Core: Electromagnetic Compatibility & Electrical Safety, issued February 1999

GR63-Core: Physical Protection Requirements, issued April 2002

SBC equipment requirements: TP76200 MP and TP76400 MP

Verizon equipment requirements: SIT.NEBS.TE.NPI.2002.010

ATM Standards

ATM Forum Traffic Management Specification Version 4.0

ATM Forum 155-Mbps Physical Layer Specification

UNI Versions 3.1 and 3.0

UNI 4.0 Traffic Management Specification

ILMI Specification Version 4.0

Network Management

Network Management via

Telnet (CLI)

Console port (CLI)

Simple Network Management Protocol (SNMP)

SONET MIB

ILMI MIB

RFC 1695

RFC 1213

Power Budget

Unit power: 30W

Optical Power Budget

Each transceiver provides a full-duplex, 155.52-Mbps, 1300-nm laser. The transmitter section uses a laser with full IEC 825 and CDRH Class 1 eye safety.

Table 1 shows the power budgets for the intermediate reach optical data link (ODL). Table 2 shows the power budgets for the long reach optical data link (ODL).

Table 1 - Intermediate Reach Optics

Fiber Power Budgets Measurement
 
Minimum
Maximum
Units
Transmitter

Optical Output Power

-15

-8

dbm

Center Wavelength

1261

1360

nm

Spectral Width RMS)

 

7.7

nm

Extinction Ratio (dynamic)

8.2

 

DB

Maximum Distance

 

15

km

   

9.3

Miles

Receiver

Sensitivity (average power)

 

-28

dBm

Saturation (average power)

-7

 

dBm

Signal Detect Assert Level

-40

 

dBm

Signal Detect De-Assert Level No, De-Assert

-45

 

dBm

Signal Detect Assert Time

 

100

sec

Signal Detect De-Assert Time

 

300

sec


Table 2 - Long Reach Optics

Fiber Power Budgets Measurement
 
Minimum
Maximum
Units
Transmitter

Optical Output Power

-5

-0

dbm

Center Wavelength

1261

1360

nm

Maximum Distance

 

40

km

   

25

Miles

Receiver

Sensitivity (average power)

 

-30

dBm

Saturation (average power)

-10

 

dBm


Hardware Requirements

Chassis—The 4-port OC3 ATM line card is supported on all Cisco 10000 Series chassis

Performance routing engines (PREs)—The 4-port OC3 ATM line card is supported on all PREs available on the Cisco 10000 Series

Software Requirements

Initial IOS Releases: The 4-port OC3 ATM line card with intermediate optics is supported in 12.0(20)ST, 12.0(22)S, 12.2(8)BZ and later Cisco IOS releases for PRE1s and in 12.2(15)BX and later Cisco IOS releases for PRE2s. The 4-port OC3 ATM line card with long reach optics is supported in 12.2(28)SB and later Cisco IOS releases for PRE2s. For the latest IOS release information, refer to:

http://www.cisco.com/pcgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi.

Ordering Information

Part Number

Description

ESR-4OC3-ATM-SM

Four-port OC-3c/STM-1c ATM line card for the Cisco 10000 Series

ESR-4OC3-ATM-SM=

Four-port OC-3c/STM-1c ATM line card for the Cisco 10000 Series, SPARE

ESR-4OC3ATM-SM-LR

4 port OC3/STM1 ATM Line Card, SM Long Reach Optics

ESR-4OC3ATM-SM-LR=

4 port OC3/STM1 ATM Line Card, SM Long Reach Optics, SPARE


Service and Support

Cisco Systems offers a wide range of service and support options for its customers. More information on Cisco service and support programs and benefits can be found at:

http://www.cisco.com/en/US/support/