Products & Services

Contents

Summary
Affected Products
Details
Vulnerability Scoring Details
Impact
Software Versions and Fixes
Workarounds
Obtaining Fixed Software
Exploitation and Public Announcements
Status of this Notice: Final
Distribution
Revision History
Cisco Security Procedures

This section provides details on affected products.

Vulnerable Products

Products Confirmed Not Vulnerable

The two issues described in this document affect the proper operation of cable modem systems. One issue results from historical behavior of cable modems not manufactured by Cisco. The other issue results from a defect in Cisco IOS Software running on a cable modem termination system (CMTS) that allows a cable modem to operate with an invalid configuration.

When a cable modem in a customer premises environment (CPE) initializes, it obtains a configuration file from the service provider's network using the Trivial File Transfer Protocol (TFTP) via a coaxial cable connection to the service provider's network. Historically, cable modems from other, non-Cisco manufacturers allow the configuration information to be downloaded via the device's Ethernet interface. By running a TFTP server on a customer premises computer and setting that computer's IP address equal to the service provider's TFTP server, a different configuration file can be downloaded to such a cable modem from the customer premises network.

The industry-standard Data Over Cable Service Interface Specification (DOCSIS) for cable modem configuration information includes a Message Integrity Check (MIC) based on a Message Digest 5 (MD5) hash of the contents of the configuration. MD5 is a one-way (non-invertible) hash—meaning that the input cannot be recovered from the output—and the output is considered unique for a specific input. If the MIC is not correct, the cable modem registration process fails and it will not be allowed to come on line. Publicly available tools exist to create a DOCSIS-compliant configuration, including a valid MIC. The cable shared-secret command in Cisco IOS Software configures a password that is included in the MD5 hash that produces the MIC; without the password, it is computationally infeasible to produce the correct matching MIC, and the cable modem is prevented from registering with the service provider's network.

If the shared secret is configured identically on all of the systems within a service provider's network and TFTP spoofing is possible as shown above, then other valid configurations containing different parameters for the same service provider network can be interchanged and downloaded to a cable modem. The modem will be allowed to come on line because the shared secret is the same. In addition, while the MD5 hash is non-invertible, the shared secret to compute it can be recovered from the CMTS router configuration. It can be protected by using the "service password-encryption" command in Cisco IOS Software, but the command uses "mode 7" encryption, which is considered adequate only for basic protection from casual viewing.

A defect in Cisco IOS Software for the uBR7200 and uBR7100 series Universal Broadband Routers causes the MD5 test to be skipped if an MIC is not provided in the DOCSIS configuration file. A DOCSIS configuration can be modified with a hex editor to truncate the file just before the MIC and adjust other fields to produce an invalid configuration file that will be accepted by the cable modem and the CMTS. When the cable modem attempts to register, a vulnerable CMTS fails to challenge the missing MIC and allows the cable modem to come on line. Using this vulnerability, the range of possible configurations is no longer restricted to a small alternative set for the same service provider; a completely custom configuration can be generated in which all of the options can be specified. This defect is documented as CSCdx72740, and details are available to registered users of the Cisco website.

The Cisco IOS Software configuration command cable tftp-enforce prohibits a cable modem from registering and coming on line if there is no matching TFTP traffic through the CMTS preceding the registration attempt. This feature has been introduced via CSCdx57688 and can be viewed by registered users of the Cisco website. This new command is available on the uBR10012 router as well as the uBR7200 and uBR7100 series.

Both the cable tftp-enforce command feature and the fix for the MD5 authentication bypass are necessary to properly mitigate these vulnerabilities, and Cisco is making fixed software available as shown below.

Some non-Cisco cable modems may be running older versions of software that save a local copy of the configuration information and use that cached copy at registration time instead of obtaining the actual file from a TFTP server. In addition to the possibility that the cable modem is not using the proper configuration information, the cable modem's user may be mistakenly accused of attempting theft of service.

CVSS is a standards-based scoring method that conveys vulnerability severity and helps determine urgency and priority of response.

Cisco has provided a base and temporal score. Customers can then compute environmental scores to assist in determining the impact of the vulnerability in individual networks.

Cisco has provided an FAQ to answer additional questions regarding CVSS at
http://www.cisco.com/web/about/security/intelligence/cvss-qandas.html .

Cisco has also provided a CVSS calculator to help compute the environmental impact for individual networks at
http://intellishield.cisco.com/security/alertmanager/cvss .

These vulnerabilities can be exploited to commit theft of service. For example, an attacker could obtain a basic level of service from a service provider and then exploit these vulnerabilities to reconfigure the CPE cable modem to provide greater upstream and downstream data rates. Thus the attacker obtains premium service at a basic cost.

Removing limits on bandwidth could result in a denial of service or degradation of performance for other users of the same cable network segment.

The Cisco IOS Software table below provides the label of the first release within a release train that contains the fix for the vulnerability described in this notice. A release train is assumed to be vulnerable if it is included below unless it is specifically labeled "Not Vulnerable". Each row of the table describes a release train and the platforms or products for which it is intended. If a given release train is vulnerable, then the earliest possible releases that contain the fix (the "First Fixed Release") and the anticipated date of availability for each are listed in the Rebuild, Interim, and Maintenance columns. A device running a release in the given train that is earlier than the release in a specific column (less than the First Fixed Release) is known to be vulnerable. The release should be upgraded at least to the indicated release or a later version (greater than or equal to the First Fixed Release label). When selecting a release, keep in mind the following definitions:

• Maintenance - Most heavily tested, stable, and highly recommended release of a release train in any given row of the table.
  
• Rebuild - Constructed from the previous maintenance or major release in the same train, it contains the fix for a specific defect. Although it receives less testing, it contains only the minimal changes necessary to repair the vulnerability.
  
• Interim - Built at regular intervals between maintenance releases and receives less testing. Interims should be selected only if there is no other suitable release that addresses the vulnerability. Interim images should be upgraded to the next available maintenance release as soon as possible. Interim releases are not available through manufacturing, and usually they are not available for customer download from CCO without prior arrangement with the Cisco Technical Assistance Center (TAC).
  

Please note that the release label shown below may not be the best release for a specific situation. In all cases, customers should exercise caution to confirm that the devices to be upgraded contain sufficient memory and that current hardware and software configurations will continue to be supported properly by the new software release. If the information is not clear, contact the Cisco TAC for assistance as shown in Obtaining Fixed Software.

More information on Cisco IOS software release names and abbreviations is available at http://www.cisco.com/warp/public/620/1.html.

The fixes will be available at the Software Center located at http://www.cisco.com/public/sw-center/.

Software installation and upgrade procedures are available at http://www.cisco.com/warp/public/130/upgrade_index.shtml.

There is no workaround for the MD5 bypass vulnerability. Customers are strongly encouraged to use the cable tftp-enforce command, deploy a shared-secret scheme and change the secret routinely, and monitor CMTS routers for evidence of tampering with bandwidth restrictions.

If the service provider has only one service profile, then the cable qos permission enforce command can be used to prevent cable modems from coming on line with a configuration containing any other service profile. This command is effective in all releases where it is supported.

The no cable qos permission modem command prevents a configuration with a new service profile from being created. This would restrict service theft to service profiles from known, pre-existing configuration files on the service provider's TFTP server, assuming the file names could be guessed and the server could be reached.

Cisco has made free software available to address this vulnerability for affected customers. Prior to deploying software, customers should consult their maintenance provider or check the software for feature set compatibility and known issues specific to their environment.

Customers may only install and expect support for the feature sets they have purchased. By installing, downloading, accessing or otherwise using such software upgrades, customers agree to be bound by the terms of Cisco's software license terms found at http://www.cisco.com/public/sw-license-agreement.html, or as otherwise set forth at Cisco.com Downloads at http://www.cisco.com/public/sw-center/sw-usingswc.shtml.

Do not contact either "psirt@cisco.com" or "security-alert@cisco.com" for software upgrades.

Customers with Service Contracts

Customers using Third Party Support Organizations

Customers without Service Contracts

These vulnerabilities have been widely discussed in public and instructions for exploiting them are available on multiple websites. The Cisco PSIRT is aware of numerous incidents of theft of service by exploiting these vulnerabilities.

THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.

A stand-alone copy or Paraphrase of the text of this document that omits the distribution URL in the following section is an uncontrolled copy, and may lack important information or contain factual errors.

This notice will be posted on Cisco's worldwide website at http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20020617-cmts-md5-bypass. In addition to worldwide web posting, a text version of this notice is clear-signed with the Cisco PSIRT PGP key and is posted to the following e-mail and Usenet news recipients:

• cust-security-announce@cisco.com
  
• bugtraq@securityfocus.com
  
• first-teams@first.org (includes CERT/CC)
  
• cisco@spot.colorado.edu
  
• cisco-nsp@puck.nether.net
  
• comp.dcom.sys.cisco
  
• firewalls@lists.gnac.com
  
• Various internal Cisco mailing lists
  

Future updates of this notice, if any, will be placed on Cisco's worldwide web server, but may or may not be actively announced on mailing lists or newsgroups. Users concerned about this problem are encouraged to check the URL given above for any updates.

Complete information on reporting security vulnerabilities in Cisco products, obtaining assistance with security incidents, and registering to receive security information from Cisco, is available on Cisco's worldwide website at http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html. This includes instructions for press inquiries regarding Cisco security notices. All Cisco security advisories are available at http://www.cisco.com/go/psirt.