|
Table Of Contents
Cisco CallManager 3.2 Integration Guide for Cisco Unity 4.0
Task List to Create the Integration
Task List to Make Changes to an Integration
Task List to Change the Number of Voice Messaging Ports
Task List to Delete an Existing Integration
Integrations with Two Phone Systems
Planning How the Voice Messaging Ports Will Be Used by Cisco Unity
Preparing for Programming the Phone System
Programming the Cisco CallManager Phone System
Setting Up the Gateways That Service Cisco Unity
Creating a New Integration with the Cisco CallManager Phone System
Integrating a Secondary Server for Cisco Unity Failover
Setting Up the Secondary Server for Failover
Changing the Settings for an Existing Integration
Changing the Number of Voice Messaging Ports
Deleting an Existing Integration
Troubleshooting the Cisco CallManager Integration
Cisco Unity Does Not Answer When the Extension for Cisco Unity Is Dialed
Appendix: Using Alternate Extensions and MWIsSetting Up Alternate Extensions
Setting Up Alternate MWIs for Extensions on the Same Phone System
MWIs for Extensions on a Non-Integrated Phone System
Setting Up MWIs for Extensions on a Non-Integrated Phone System
Appendix: Documentation and Technical AssistanceObtaining Technical Assistance
Cisco Technical Support Website
Obtaining Additional Publications and Information
Cisco CallManager 3.2 Integration Guide for Cisco Unity 4.0
Revised November 14, 2005
This document provides instructions for integrating the phone system with Cisco Unity.
Integration Tasks
Before doing the following tasks to integrate Cisco Unity with the Cisco CallManager phone system, confirm that the Cisco Unity server is ready for the integration by completing the applicable tasks in the Cisco Unity Installation Guide.
The following task lists describe the process for creating, changing, and deleting integrations.
Task List to Create the Integration
Use the following task list to set up a new integration with the Cisco CallManager phone system. If you are installing a new Cisco Unity server by using the Cisco Unity Installation Guide, you may have already completed some of the following tasks.
1. Review the system and equipment requirements to confirm that all phone system and Cisco Unity server requirements have been met. See the "Requirements" section.
2. Plan how the voice messaging ports will be used by Cisco Unity. See the "Planning How the Voice Messaging Ports Will Be Used by Cisco Unity" section.
3. Program Cisco CallManager. See the "Programming the Cisco CallManager Phone System" section.
•When configuring voice mail ports for a Cisco Unity server without failover or the primary server with failover, do all the procedures in this section.
•When configuring voice mail ports for a secondary server with failover, do only the "To Add Voice Mail Ports to Cisco CallManager" procedure.
4. Set up the gateways that service Cisco Unity. See the "Setting Up the Gateways That Service Cisco Unity" section.
5. Create the integration. See the "Creating a New Integration with the Cisco CallManager Phone System" section.
6. Test the integration. See the "Testing the Integration" section.
7. If you have a secondary server for Cisco Unity failover, integrate the secondary server. See the "Integrating a Secondary Server for Cisco Unity Failover" section.
Task List to Make Changes to an Integration
Use the following task list to make changes to an integration after it has been created.
1. Start the Cisco Unity Telephony Integration Manager (UTIM). See the "Changing the Settings for an Existing Integration" section.
2. Make the changes you want to the existing integration. See the "Changing the Settings for an Existing Integration" section.
Task List to Change the Number of Voice Messaging Ports
Use the following task list to change the number of voice messaging ports for an integration after it has been created.
1. Change the number of voice messaging ports. See the "Changing the Number of Voice Messaging Ports" section.
2. Start the Cisco Unity Telephony Integration Manager (UTIM). See the "Changing the Settings for an Existing Integration" section.
3. Make the changes you want to the existing integration. See the "Changing the Settings for an Existing Integration" section.
Task List to Delete an Existing Integration
Use the following task list to remove an existing integration.
1. Start the Cisco Unity Telephony Integration Manager (UTIM). See the "Deleting an Existing Integration" section.
2. Delete the existing integration. See the "Deleting an Existing Integration" section.
Requirements
The Cisco CallManager integration supports configurations of the following components:
Phone System
•A Cisco IP telephony applications server consisting of Cisco CallManager 3.2(1) or later, running on a Cisco Media Convergence Server (MCS) or customer-provided server meeting approved Cisco configuration standards.
•Cisco licenses for all phone lines, IP phones, and other H.323-compliant devices or software (such as Cisco VirtualPhone and Microsoft NetMeeting clients) that will be connected to the network, as well as one license for each Cisco Unity port.
•IP phones for the Cisco CallManager extensions.
•A LAN connection in each location where you will plug an IP phone into the network.
•For multiple Cisco CallManager clusters, subscribers can dial an extension on another Cisco CallManager cluster without having to dial a trunk access code or prefix.
Cisco Unity Server
•Cisco Unity version 4.0(1) or later, installed and ready for the integration as described in the Cisco Unity Installation Guide.
•A license that enables the applicable number of voice messaging ports.
Integration Description
The Cisco CallManager integration uses the LAN to connect Cisco Unity and the phone system. The gateway provides connections to the PSTN. Figure 1 shows the connections.
Figure 1 Connections Between the Phone System and Cisco Unity
Call Information
The phone system sends the following information with forwarded calls:
•The extension of the called party
•The extension of the calling party (for internal calls) or the phone number of the calling party (if it is an external call and the system uses caller ID)
•The reason for the forward (the extension is busy, does not answer, or is set to forward all calls)
Cisco Unity uses this information to answer the call appropriately. For example, a call forwarded to Cisco Unity is answered with the personal greeting of the subscriber. If the phone system routes the call to Cisco Unity without this information, Cisco Unity answers with the opening greeting.
Integration Features
The Cisco CallManager integration with Cisco Unity provides the following features.
When a Cisco Survivable Remote Site Telephony (SRST) router is part of the network and the Cisco SRST router takes over call processing functions (for example, because the WAN link is down), the Cisco SRST integration with Cisco Unity has the following feature limitations:
•Call forward to busy greeting—When the Cisco SRST router uses FXO/FXS connections to the PSTN and a call is forwarded from a branch office to Cisco Unity, the busy greeting cannot play.
•Call forward to internal greeting—When the Cisco SRST router uses FXO/FXS connections to the PSTN and a call is forwarded from a branch office to Cisco Unity, the internal greeting cannot play. Because the PSTN provides the calling number of the FXO line, the caller is not identified as a subscriber.
•Call transfers—Because an access code is needed to reach the PSTN, call transfers from Cisco Unity to a branch office will fail.
•Identified subscriber messaging—When the Cisco SRST router uses FXO/FXS connections to the PSTN and a subscriber at a branch office leaves a message or forwards a call, the subscriber is not identified. The caller appears as an unidentified caller.
•Message waiting indication—MWIs are not updated on branch office phones. So MWIs will not correctly reflect when new messages arrive or when all messages have been listened to. We recommend resynchronizing MWIs after the WAN link is reestablished.
•Message notification—Because an access code is needed to reach the PSTN, message notifications from Cisco Unity to a branch office will fail.
•Routing rules—When the Cisco SRST router uses FXO/FXS connections to the PSTN and a call arrives from a branch office to Cisco Unity (either a direct or forwarded call), routing rules will fail.
When the Cisco SRST router uses PRI/BRI connections, the caller ID for calls from a branch office to Cisco Unity may be the full number (exchange plus extension) provided by the PSTN and therefore may not match the extension of the Cisco Unity subscriber. If this is the case, you can let Cisco Unity recognize the caller ID by using alternate extensions (for instructions, see the "Appendix: Using Alternate Extensions and MWIs" section) or by using extension remapping (for instructions, refer to the "Remapping Extension Numbers" section of the "System Settings" chapter in the applicable Cisco Unity System Administration Guide (release 4.0(3) or later), available at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_administration_guides_list.html.
For information on setting up Cisco SRST routers, refer to the "Integrating Voice Mail with Cisco SRST" section of the "Cisco SRST System Administrator Guide," available at http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122limit/122z/122zj15/index.htm.
Integrations with Two Phone Systems
Cisco Unity can be integrated with two phone systems at one time. For information on and instructions for integrating Cisco Unity with two phone systems, see the Dual Phone System Integration Guide, available at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_unity/integuid/multi/itmultin.htm.
Having two integrations requires that an adequate number of voice messaging ports on the Cisco Unity server are connected to the phone systems. This number of ports must not exceed the maximum number of ports that are enabled by the Cisco Unity license files.
Planning How the Voice Messaging Ports Will Be Used by Cisco Unity
Before programming the phone system, you need to plan how the voice messaging ports will be used by Cisco Unity. The following considerations will affect the programming for the phone system (for example, setting up the hunt group or call forwarding for the voice messaging ports):
•The number of voice messaging ports installed.
•The number of voice messaging ports that will answer calls.
•The number of voice messaging ports that will only dial out, for example, to send message notification, to set message waiting indicators (MWIs), to make AMIS deliveries, and to make telephone record and playback (TRAP) connections.
•The number of voice messaging ports that will be dedicated to set MWIs if Cisco Unity is connected to multiple clusters of Cisco CallManager and if the Cisco CallManager server has dedicated MWI voice messaging ports.
Table 1 describes the voice messaging port settings in Cisco Unity that can be set in UTIM and are displayed as read-only text on the System > Ports page of the Cisco Unity Administrator.
The Number of Voice Messaging Ports to Install
The number of voice messaging ports to install depends on numerous factors, including:
•The number of calls Cisco Unity will answer when call traffic is at its peak.
•The expected length of each message that callers will record and that subscribers will listen to.
•The number of subscribers.
•The number of ports that will be set to dial out only.
•The number of calls made for message notification.
•The number of MWIs that will be activated when call traffic is at its peak.
•The number of AMIS delivery calls.
•The number of TRAP connections needed when call traffic is at its peak. (TRAP connections are used by Cisco Unity web applications and e-mail clients to play back and record over the phone.)
It is best to install only the number of voice messaging ports that are needed so that system resources are not allocated to unused ports.
The Number of Voice Messaging Ports That Will Answer Calls
The calls that the voice messaging ports answer can be incoming calls from unidentified callers or from subscribers. Typically, these voice messaging ports are the busiest. They also have the lowest port numbers for the phone system.
You can set voice messaging ports to both answer calls and to dial out (for example, to send message notifications).
The Number of Voice Messaging Ports That Will Only Dial Out, and Not Answer Calls
Ports that will only dial out and will not answer calls can do one or more of the following:
•Notify subscribers by phone, pager, or e-mail of messages that have arrived.
•Turn MWIs on and off for subscriber extensions.
•Make outbound AMIS calls to deliver voice messages from Cisco Unity subscribers to users on another voice messaging system. (This action is available only with the AMIS licensed feature.)
•Make a TRAP connection so that subscribers can use the phone as a recording and playback device in Cisco Unity web applications and e-mail clients.
Typically, these voice messaging ports are the least busy ports. They also have the highest port numbers for the phone system.
Caution In programming the phone system, do not send calls to voice messaging ports in Cisco Unity that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Dialout MWI, do not send calls to it.
The Number of Voice Messaging Ports That Will Be Dedicated to Activating MWIs on Other Cisco CallManager Clusters
If Cisco Unity services multiple clusters of Cisco CallManager, there must be at least one voice messaging port per cluster dedicated for turning MWIs on and off for each cluster. For example, if the system has four clusters, at least four ports on Cisco Unity must be dedicated to activating MWIs, one port for each cluster.
Preparing for Programming the Phone System
Record your decisions about the voice messaging ports to guide you in programming the phone system.
Programming the Cisco CallManager Phone System
After Cisco CallManager software is installed, do the procedures in this section to program Cisco CallManager to work with Cisco Unity:
•When configuring voice mail ports for a Cisco Unity server without failover, or the primary server with failover, do all the procedures in this section.
•When configuring voice mail ports for a secondary server with failover, do only the "To Add Voice Mail Ports to Cisco CallManager" procedure.
To Add Partitions and a Calling Search Space to Contain the Voice Mail Ports
Step 1 In the Cisco CallManager Administration, click Route Plan > Partition.
Step 2 Click Add a New Partition.
Step 3 Enter the name and description you want for the partition that will contain all voice mail port directory numbers except for the first voice mail port, which will be assigned the voice mail pilot number. For example, enter "VMRestrictedPT, Partition for voice mail port directory numbers." For a diagram of the configuration, see Figure 2. For a diagram of the configuration with Cisco Unity failover, see Figure 3.
Step 4 Click Insert.
Step 5 Click Add a New Partition.
Step 6 Enter the name and description you want for the partition that will contain the directory number of the first voice mail port, which will be assigned the voice mail pilot number. For example, enter "VMPilotNumberPT, Partition for the voice mail pilot number." For a diagram of the configuration, see Figure 2. For a diagram of the configuration with Cisco Unity failover, see Figure 3.
Step 7 Click Insert.
Step 8 Click Route Plan > Calling Search Space.
Step 9 Click Add a New Calling Search Space.
Step 10 In the Calling Search Space Name field, enter a name for the calling search space that will include the partition created in Step 2 through Step 4. For example, enter "VMRestrictedCSS."
Step 11 If you want, in the Description field, enter a description of the calling search space. For example, enter "Voice mail port directory numbers."
Step 12 In the Available Partitions field, double-click the name of the partition created in Step 2 through Step 4. For example, double-click "VMRestrictedPT." For a diagram of the configuration, see Figure 2. For a diagram of the configuration with Cisco Unity failover, see Figure 3.
The name of the partition appears in the Selected Partitions field.
Step 13 Click Insert.
Step 14 Click Back to Find/List Calling Search Spaces.
Step 15 Click the name of the calling search space that is used by subscriber phones.
Step 16 In the Available Partitions field, double-click the name of the partition created in Step 5 through Step 7. For example, double-click "VMPilotNumberPT." For a diagram of the configuration, see Figure 2. For a diagram of the configuration with Cisco Unity failover, see Figure 3.
Caution If the partition that contains the voice mail pilot number is not in the calling search space that is used by subscriber phones, the phones will not be able to dial the Cisco Unity server.
Step 17 Click Update.
Step 18 Repeat Step 15 through Step 17 for each remaining calling search space that needs to access Cisco Unity.
Figure 2 Partitions for Voice Mail Port Directory Numbers
Figure 3 Partitions for Voice Mail Port Directory Numbers with Cisco Unity Failover
To Add a Device Pool for the Voice Mail Ports
Step 1 In the Cisco CallManager Administration, click System > Device Pool.
Step 2 On the Device Pool Configuration page, enter the following device pool settings.
Step 3 Click Insert.
To Add Voice Mail Ports to Cisco CallManager
Add a voice mail port to Cisco CallManager for each port that you are connecting to Cisco Unity.
Step 1 In the Cisco CallManager Administration, click Feature > Voice Mail > Cisco Voice Mail Port Wizard.
Step 2 Click Create a New Cisco Voice Mail Server and Add Ports to It and click Next.
Step 3 The name of the voice mail server appears. We recommend that you accept the default name for the voice mail server, or, if necessary, enter a different name with no more than nine characters, then click Next.
The default name (CiscoUM), even if you do not use it, becomes part of the name for ports as follows:
<the voice mail server name>1 (for example, CiscoUM1).
Caution If Cisco Unity is configured for failover, the name of the voice mail server and voice mail ports that serve the secondary server must be different from the name of the voice mail server and voice mail ports that serve the primary server. Otherwise, the secondary server cannot function correctly.
Step 4 Enter the number of ports you want to add (which must not be more ports than the Cisco Unity license enables), then click Next.
If you will integrate Cisco Unity with multiple clusters of Cisco CallManager, the number you enter here cannot bring the total number of ports on all clusters integrated with Cisco Unity to more than the number of ports enabled by the Cisco Unity license.
Step 5 Enter the following voice mail device settings, then click Next.
Step 6 Enter the following voice mail directory number settings, then click Next.
Table 4 Settings for the Voice Mail Directory Numbers
Field SettingPilot Number
Enter the pilot number for the voice mail ports.
The pilot number is the extension number of the first voice mail port and is the number subscribers enter to listen to their voice messages.
If Cisco Unity is configured for failover and you are adding voice mail ports for the secondary server, the pilot number is the extension number of the first voice mail port on the secondary server, but it is not the number subscribers enter to listen to their voice messages.
Partition
Click the name of the partition that you set up for all voice mail port directory numbers except the first voice mail port. For example, click "VMRestrictedPT."
Calling Search Space
Click the name of a calling search space that you set up to contain the partition with all voice mail port directory numbers except the first voice mail port, as set in Step 9 of the "To Add Partitions and a Calling Search Space to Contain the Voice Mail Ports" section. For example, click "VMRestrictedCSS."
Because this calling search space is not used by subscriber phones, subscribers cannot dial any voice mail ports except the voice mail pilot number.
Display
Accept the default of Voicemail. (This text appears on the phone when the pilot number is dialed.)
Caution If Cisco Unity is configured for failover, do not change the default setting for this field. Otherwise, the integration will not function correctly.
Step 7 Enter the operator number or the number you want the last port to forward to when busy, if applicable, and click Next.
Step 8 The settings for the new ports appear. Click Finish.
Step 9 Click Go to Cisco Voice Mail Ports Page.
Note If Cisco Unity is configured for failover and you are setting ports for the secondary server, skip the remaining procedures in this section and continue to the "Creating a New Integration with the Cisco CallManager Phone System" section. For further instructions on configuring the voice mail ports, see the "Integrating a Secondary Server for Cisco Unity Failover" section.
To Set the Partition for the First Voice Mail Port
Step 1 On the Cisco Voice Mail Port Configuration page, in the Cisco Voice Mail Ports list, click the first voice mail port, which is assigned the voice mail pilot number.
Step 2 Under Directory Number Information, in the Partition field, click the partition that you set up to contain the first voice mail port. For example, click "VMPilotNumberPT."
Step 3 Click Update.
To Specify MWI Directory Numbers
Step 1 In the Cisco CallManager Administration, click Feature > Voice Mail > Message Waiting.
Step 2 In the Message Waiting Directory Numbers list of the Message Waiting Configuration page, click Add a New Directory Number.
Step 3 Enter the following settings for turning MWIs on.
Step 4 Click Insert.
Step 5 In the Message Waiting Directory Numbers list, click Add a New Directory Number.
Step 6 Enter the following settings for turning MWIs off.
Step 7 Click Insert.
To Add a Voice Mail Pilot Number for the Voice Mail Ports
The voice mail pilot number is the extension that you dial to listen to your voice messages. Your Cisco IP phone automatically dials the voice mail pilot number when you press the Messages button.
Step 1 In the Cisco CallManager Administration, click Feature > Voice Mail > Voice Mail Pilot.
Step 2 In the Voice Mail Pilot Numbers list of the Voice Mail Pilot Configuration page, click Add a New Voice Mail Pilot Number.
Step 3 Enter the following voice mail pilot number settings.
Step 4 Click Insert.
To Set Up the Voice Mail Profile
Step 1 In the Cisco CallManager Administration, click Feature > Voice Mail > Voice Mail Profile.
Step 2 In the Find and List Voice Mail Profiles page, click Add a New Voice Mail Profile.
Step 3 In the Voice Mail Profiles Configuration page, enter the following voice mail profile settings.
Step 4 Click Insert.
To Set Up the Voice Mail Server Service Parameters
Step 1 In the Cisco CallManager Administration, click Service > Service Parameters.
Step 2 In the Server field on the Service Parameters Configuration page, click the voice mail server that you created earlier.
Step 3 In the Services list, click Cisco CallManager. The list of parameters appears.
Step 4 Scroll down the list until you locate the parameters listed in Table 9 (about three-quarters of the way).
Step 5 Enter the parameter settings shown in the following table.
Step 6 Click Update to save the settings.
Step 7 Click Select Another Service at the top of the page.
Step 8 In the Services list, click Cisco Messaging Interface. The list of parameters appears.
Step 9 Confirm that the VoiceMailDn parameter setting is blank.
Step 10 If you changed the parameter setting to blank, click Update to save the setting.
Step 11 Shut down and restart the Cisco CallManager server.
If the plan for voice mail ports in Cisco Unity (see the "Planning How the Voice Messaging Ports Will Be Used by Cisco Unity" section) includes ports that do not answer calls (for example, ports that only dial out to set MWIs), do the following procedure so that incoming calls are not forwarded to these ports.
To Set Up Voice Mail Ports So Incoming Calls Are Forwarded Only to Answering Ports
Step 1 In the Cisco CallManager Administration, click Feature > Voice Mail > Cisco Voice Mail Port.
Step 2 In the Cisco Voice Mail Ports list of the Cisco Voice Mail Port Configuration page, click the name of the last voice mail port that answers calls in Cisco Unity.
Step 3 Set the Forward Busy and Forward No Answer fields to forward to the first voice mail port that answers calls in Cisco Unity.
Step 4 Click Update.
Step 5 In the Cisco Voice Mail Ports list, click the name of a the first voice mail port that does not answer calls in Cisco Unity.
Step 6 Under Call Forwarding Information, delete the extensions in the Forward Busy field, and set the Forward No Answer field to forward to the first voice mail port that answers calls in Cisco Unity.
Step 7 Click Update.
Step 8 Repeat Step 5 through Step 7 for all remaining voice mail ports that do not answer calls in Cisco Unity.
If the Cisco Unity server services multiple clusters of Cisco CallManager, do the following procedure to enable MWIs to be activated on extensions in each cluster.
To Set Up MWI Voice Mail Ports for Multiple Clusters of Cisco CallManager
Step 1 In the Cisco Unity Administrator, select at least one voice mail port per cluster to be dedicated for sending MWIs to each cluster. For example, if the system has four clusters, dedicate at least four ports to send only MWIs, one port from each cluster.
Step 2 In the Cisco CallManager Administration, click Feature > Voice Mail > Cisco Voice Mail Port.
Step 3 In the Cisco Voice Mail Ports list of the Cisco Voice Mail Port Configuration page, click the name of the port before the first dedicated MWI port.
Step 4 Under Call Forwarding Information, change the extensions to the number of the first voice mail port or of the operator.
Step 5 Click Update.
Step 6 In the Cisco Voice Mail Ports list, click the name of a dedicated MWI port.
Step 7 Under Call Forwarding Information, delete the extensions so that the fields are empty and call forwarding for this port is disabled.
Step 8 Click Update.
Step 9 Repeat Step 6 through Step 8 for all remaining dedicated MWI ports.
You can use alternate extensions to create multiple line appearances, enable easy message access from cell phones, and simplify addressing messages to subscribers at different locations in Cisco Unity. When you enable alternate MWIs, Cisco Unity can turn MWIs on at more than one extension. For details, see the "Appendix: Using Alternate Extensions and MWIs" section.
Setting Up the Gateways That Service Cisco Unity
In certain situations, DTMF digits are not recognized when processed through VoIP dial-peer gateways. To avoid this problem, certain gateways must be configured to enable DTMF relay. The DTMF relay feature is available in Cisco IOS software version 12.0(5) and later.
Cisco IOS software-based gateways that use H.245 out-of-band signaling must be configured to enable DTMF relay.
Enable dtmf-relay h245-alphanumeric on this dial-peer.
The Catalyst 6000 T1/PRI and FXS gateways enable DTMF relay by default and do not need additional configuration to enable this feature.
To Enable DTMF Relay
Step 1 On a VoIP dial-peer servicing Cisco Unity, use the following command:
dtmf-relay h245-alphanumericStep 2 Create a destination pattern that matches the Cisco CallManager voice mail port numbers. For example, if the system has voice mail ports 1001 through 1016, enter the dial-peer destination pattern 10xx.
Step 3 Repeat Step 1 and Step 2 for all remaining VoIP dial-peers servicing Cisco Unity.
Creating a New Integration with the Cisco CallManager Phone System
After ensuring that the Cisco CallManager phone system and the Cisco Unity server are ready for the integration, do the following procedures to set up the integration and to enter the port settings.
Note If you are integrating with multiple clusters of Cisco CallManager, you must integrate Cisco Unity with each additional cluster. Skip to the "To Create an Integration with a Second Cluster of Cisco CallManager" procedure.
To Create an Integration
Step 1 If UTIM is not already open, on the Windows Start menu, click Programs > Cisco Unity > Manage Integrations. UTIM appears.
Step 2 On the Integration menu of the UTIM window, click New. The Telephony Integration Setup Wizard appears.
Step 3 On the Welcome page, click Cisco CallManager, then click Next.
Step 4 On the Name Cisco CallManager Integration and Cluster page, enter the following settings, then click Next.
Step 5 On the Enter Cisco CallManager IP Address and Port page, enter the following settings, then click Next.
You can click Ping Server to confirm that the IP address is correct.
Step 6 On the Enter Secondary Server Settings page, in the IP Address/Name field, enter the IP address (or DNS name) and port of all remaining subscriber (secondary) Cisco CallManager servers in the cluster and of the publisher (primary) Cisco CallManager server. Then click Add after entering each so that the IP addresses of all secondary servers appear in the list. If there is only one Cisco CallManager server in the cluster, leave this page blank.
The IP addresses of the subscriber (secondary) Cisco CallManager servers must appear in descending order, so that the subscriber (secondary) Cisco CallManager server at the top of the list is the first to take over call processing functions during failover, and the publishing (primary) Cisco CallManager server is the last.
You can click Ping Servers to confirm that the IP addresses are correct.
Step 7 If you want Cisco Unity to automatically reconnect to the primary Cisco CallManager server after failover has been corrected, check the Reconnect to Primary Cisco CallManager Server check box.
Step 8 Click Next.
Step 9 On the Enter Cisco CallManager MWI Extensions page, enter the following settings, then click Next.
Step 10 On the Set Number of Voice Messaging Ports page, enter the following settings, then click Next.
You can click Verify to confirm that the CallManager device name prefix is correct.
Step 11 If another integration already exists, the Enter Trunk Access Code page appears. Enter the extra digits that Cisco Unity must use to transfer calls through the gateway to extensions on the other phone system with which it is integrated. Then click Next.
Step 12 On the Completing page, verify the settings you entered, then click Finish.
Step 13 At the prompt to restart the Cisco Unity services, click Yes. The Cisco Unity services restart.
Alternatively, you can restart the Cisco Unity services in UTIM on the Tools menu by clicking Restart Cisco Unity. Do not use the taskbar icon to restart the Cisco Unity for UTIM changes because the taskbar icon does not restart all of the Cisco Unity services.
To Enter the Voice Messaging Port Settings for the Integration
Step 1 After the Cisco Unity services restart, on the Windows Start menu, click Programs > Cisco Unity > Manage Integrations. UTIM appears.
Step 2 In the left pane of the UTIM window, click the phone system integration you are creating.
Step 3 In the right pane, click the phone system or cluster name.
Step 4 In the right pane, click the Ports tab.
Step 5 Enter the settings shown in Table 14 for the voice messaging ports.
For the voice messaging ports assigned to a given Cisco CallManager cluster, to get the best performance use the first voice messaging ports for incoming calls and the last ports to dial out. This helps minimize the possibility of a collision, in which an incoming call arrives on a port at the same time that Cisco Unity takes the port off-hook to dial out. Set the ports assigned to each Cisco CallManager cluster in this manner.
If the Cisco Unity server is connected to multiple clusters of Cisco CallManager and if the Cisco CallManager server has dedicated MWI voice messaging ports, set each dedicated MWI voice messaging port to Dialout MWI. For example, if the system has four clusters, dedicate four ports to send only MWIs, and assign one port to each cluster.
Caution In programming Cisco CallManager, do not send calls to voice messaging ports in Cisco Unity that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Dialout MWI, do not send calls to it.
Step 6 Repeat Step 5 for the remaining clusters, if any.
Step 7 Click Save.
Step 8 If Cisco Unity integrates with only one cluster of Cisco CallManager, exit UTIM, skip the remaining procedures in this section, and continue to the "Testing the Integration" section.
If Cisco Unity integrates with multiple clusters of Cisco CallManager, continue to the next procedure.
To Create an Integration with a Second Cluster of Cisco CallManager
If Cisco Unity integrates with only one cluster of Cisco CallManager, skip this procedure.
Step 1 In the left pane of the UTIM window, click the Cisco CallManager integration.
Step 2 On the Cluster menu, click New. A new cluster appears in the Cisco CallManager integration.
Step 3 Click the Servers tab, and enter the following settings.
Step 4 Click the MWI tab, and enter the following settings.
Step 5 Click the Ports tab, and click Add Port.
Step 6 In the Add Port dialog box, enter the number of voice messaging ports on Cisco Unity you want to connect to the Cisco CallManager cluster, and click OK.
This number cannot be more than the number of ports set up on the Cisco CallManager cluster. This number cannot bring the total number of port installed on the Cisco Unity server to more than the number of ports enabled by the Cisco Unity license.
Step 7 Click the Servers tab, and click Verify Servers to confirm that the Cisco CallManager server information is correct.
Step 8 Click the RTP tab, and confirm that the Automatically Assign option is selected.
Step 9 In the UTIM window, click Save.
Step 10 At the prompt to restart the Cisco Unity services, click Yes. The Cisco Unity services restart.
Note When restarting Cisco Unity, use the UTIM prompt instead of the Cisco Unity icon in the Windows taskbar. The taskbar icon does not restart all of the Cisco Unity services.
Step 11 After the Cisco Unity services restart, on the Windows Start menu, click Programs > Cisco Unity > Manage Integrations. UTIM appears.
Step 12 In the left pane of the UTIM window, click the Cisco CallManager integration.
Step 13 In the right pane, click the name of the cluster name you created in this procedure.
Step 14 In the right pane, click the Ports tab.
Step 15 Enter the settings shown in Table 17 for the voice messaging ports.
Caution In programming Cisco CallManager, do not send calls to voice messaging ports in Cisco Unity that cannot answer calls (voice messaging ports that are not set to Answer Calls). For example, if a voice messaging port is set only to Dialout MWI, do not send calls to it.
Step 16 In the UTIM window, click Save.
Step 17 Exit UTIM.
Step 18 Repeat Step 1 through Step 17 for all remaining Cisco CallManager clusters.
Testing the Integration
To test whether Cisco Unity and the phone system are integrated correctly, do the following procedures in the order listed.
If any of the steps indicates a failure, refer to the following documentation as applicable:
•The installation guide for the phone system
•Cisco Unity Troubleshooting Guide, available at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_troubleshooting_guides_list.html
•The setup information earlier in this guide
To Set Up the Test Configuration
Step 1 Set up two test extensions (Phone 1 and Phone 2) on the same phone system that Cisco Unity is connected to.
Step 2 Set Phone 1 to forward calls to the Cisco Unity pilot number when calls are not answered.
Step 3 In the Cisco Unity Administrator, create a test subscriber to use for testing by doing the applicable substeps below.
If your message store is Microsoft Exchange, do the following:
a. In the Cisco Unity Administrator, go to the Subscribers > Subscribers > Profile page.
b. Click the Add icon.
c. Select New Exchange Subscriber.
d. Enter the applicable information on the Add Subscriber page.
e. Click Add.
If your message store is IBM Lotus Domino, do the following:
a. In the Cisco Unity Administrator, go to the Subscribers > Subscribers > Profile page.
b. Click the Add icon.
c. Click Notes.
d. In the Address Book list, confirm that the address book listed is the one that contains the user data that you want to import.
If the address book that you want to use is not listed, go to the System > Configuration > Subscriber Address Books page and add a different address book.
e. In the Find Domino Person By list, indicate whether to search by short name, first name, or last name.
f. Enter the applicable short name or name. You also can enter * to display a list of all users, or enter one or more characters followed by * to narrow your search.
g. Click Find.
h. On the list of matches, click the name of the user to import.
i. Enter the applicable information on the Add Subscriber page.
j. Click Add.
Step 4 In the Extension field, enter the extension of Phone 1.
Step 5 In the Active Schedule field, click All Hours - All Days.
Step 6 Click the Save icon.
Step 7 In the navigation bar, click Call Transfer to go to the Subscribers > Subscribers > Call Transfer page for the test subscriber.
For more information on transfer settings, refer to the "Subscriber Template Call Transfer Settings" section in the Cisco Unity Administrator Help.
Step 8 Under Transfer Incoming Calls, click Yes, Ring Subscriber's Extension, and confirm that the extension number is for Phone 1.
Step 9 Under Transfer Type, click Release to Switch.
Step 10 Click the Save icon.
Step 11 In the navigation bar, click Messages to go to the Subscribers > Subscribers > Messages page for the test subscriber.
Step 12 Under Message Waiting Indicators (MWIs), check Use MWI for Message Notification.
Step 13 In the Extension field, enter x.
Step 14 Click the Save icon.
Step 15 Open the Status Monitor by doing one of the following:
•In Internet Explorer, go to http://<Cisco Unity server name>/web/sm.
•Double-click the desktop shortcut to the Status Monitor.
•In the status bar next to the clock, right-click the Cisco Unity tray icon and click Status Monitor.
To Test an External Call with Release Transfer
Step 1 From Phone 2, enter the access code necessary to get an outside line, then enter the number outside callers use to dial directly to Cisco Unity.
Step 2 On the Status Monitor, note the port that handles this call.
Step 3 When you hear the opening greeting, enter the extension for Phone 1. Hearing the opening greeting means that the port is configured correctly.
Step 4 Confirm that Phone 1 rings and that you hear a ringback tone on Phone 2. Hearing a ringback tone means that Cisco Unity released the call and transferred it to Phone 1.
Step 5 Leaving Phone 1 unanswered, confirm that the state of the port handling the call changes to "Idle." This state means that release transfer is successful.
Step 6 Confirm that, after the number of rings that the phone system is set to wait, the call is forwarded to Cisco Unity and that you hear the greeting for the test subscriber. Hearing the greeting means that the phone system forwarded the unanswered call and the call-forward information to Cisco Unity, which correctly interpreted the information.
Step 7 On the Status Monitor, note the port that handles this call.
Step 8 Leave a message for the test subscriber and hang up Phone 2.
Step 9 On the Status Monitor, confirm that the state of the port handling the call changes to "Idle." This state means that the port was successfully released when the call ended.
Step 10 Confirm that the MWI on Phone 1 is activated. The activated MWI means that the phone system and Cisco Unity are successfully integrated for turning on MWIs.
To Test an Internal Call with Release Transfer
Step 1 From Phone 1, enter the internal pilot number for Cisco Unity.
Step 2 When asked for your password, enter 12345. Hearing the request for your password means that the phone system sent the necessary call information to Cisco Unity, which correctly interpreted the information.
Step 3 Confirm that you hear the recorded voice name for the test subscriber (if you did not record a voice name for the test subscriber, you will hear the extension number for Phone 1). Hearing the voice name means that Cisco Unity correctly identified the subscriber by the extension.
Step 4 When asked whether you want to listen to your message, press 1.
Step 5 After listening to the message, press 3 to delete the message.
Step 6 Confirm that the MWI on Phone 1 is deactivated. The deactivated MWI means that the phone system and Cisco Unity are successfully integrated for turning off MWIs.
Step 7 Hang up Phone 1.
Step 8 On the Status Monitor, confirm that the state of the port handling the call changes to "Idle." This state means that the port was successfully released when the call ended.
To Set Up Supervised Transfer on Cisco Unity
Step 1 In the Cisco Unity Administrator, go to the Subscribers > Subscribers > Call Transfer page.
If the name of the test subscriber is not displayed, click the Find icon (the magnifying glass) in the title bar, then click Find, and select the name of the test subscriber in the list that appears.
For more information on transfer settings, refer to the "Subscriber Template Call Transfer Settings" section in the Cisco Unity Administrator Help.
Step 2 Under Transfer Type, click Supervise Transfer.
Step 3 Set the Rings to Wait For field to 3.
Step 4 Click the Save icon.
To Test Supervised Transfer
Step 1 From Phone 2, enter the access code necessary to get an outside line, then enter the number outside callers use to dial directly to Cisco Unity.
Step 2 On the Status Monitor, note the port that handles this call.
Step 3 When you hear the opening greeting, enter the extension for Phone 1. Hearing the opening greeting means that the port is configured correctly.
Step 4 Confirm that Phone 1 rings and that you do not hear a ringback tone on Phone 2. Instead, you should hear the indication your phone system uses to mean that the call is on hold (for example, music or beeps).
Step 5 Leaving Phone 1 unanswered, confirm that the state of the port handling the call remains "Busy." This state and hearing an indication that you are on hold mean that Cisco Unity is supervising the transfer.
Step 6 Confirm that, after three rings, you hear the greeting for the test subscriber. Hearing the greeting means that Cisco Unity successfully recalled the supervised-transfer call.
Step 7 During the greeting, hang up Phone 2.
Step 8 On the Status Monitor, confirm that the state of the port handling the call changes to "Idle." This state means that the port was successfully released when the call ended.
To Delete the Test Subscriber
Step 1 In the Cisco Unity Administrator, go to the Subscribers > Subscribers > Profile page.
If the name of the test subscriber is not displayed, click the Find icon (the magnifying glass) in the title bar, then click Find, and select the name of the test subscriber in the list that appears.
Step 2 In the title bar, click the Delete Subscriber icon (the X).
Step 3 Click Delete.
Integrating a Secondary Server for Cisco Unity Failover
The Cisco Unity failover feature enables a secondary server to provide voice messaging services when the primary server becomes inactive. For information on installing a secondary server for failover, refer to the Cisco Unity Installation Guide, available at http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_installation_guides_list.html.
For information on failover, refer to the Cisco Unity Failover Configuration and Administration Guide, available at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_unity/fail/fail401/ex/index.htm.
Requirements
The following components are required to integrate a secondary server:
•One secondary server for each primary server installed and ready for the integration, as described in the Cisco Unity Installation Guide and earlier in this integration guide.
•A license that enables failover.
Integration Description
The phone system communicates with both the primary and secondary servers through the LAN. Figure 4 shows the required connections.
Figure 4 Connections Between Cisco CallManager and the Cisco Unity Servers
The primary and secondary servers act in the following manner:
•When the primary server is operating normally, the secondary server is inactive.
•When the primary server becomes inactive, the secondary server becomes active.
•When the primary server becomes active again, the secondary server becomes inactive.
Setting Up the Secondary Server for Failover
Before proceeding, confirm that Cisco CallManager is configured as described in the "Programming the Cisco CallManager Phone System" section earlier in this integration guide, including the following:
•For each voice mail port, the Forward Busy and Forward No Answer fields are set to forward to the next voice mail port (the default configuration of the Cisco Voice Mail Wizard).
•The name of the voice mail server and voice mail ports that serve the secondary server are different from the name of the voice mail server and voice mail ports that serve the primary server.
Do the following two procedures to integrate the secondary server.
To Configure Cisco CallManager
Step 1 In the Cisco CallManager Administration, click Feature > Voice Mail > Cisco Voice Mail Port.
Step 2 For the last voice mail port that answers calls on the primary server, set the Forward Busy field to the first voice mail port on the primary server.
If there are voice mail ports on the primary server that do not answer calls (for example, voice mail ports set only to Dialout MWI), leave the Forward Busy field blank.
Caution In programming Cisco CallManager, do not send calls to ports in Cisco Unity that cannot answer calls (ports that are not set to Answer Calls). For example, if a port is set only to Dialout MWI, do not send calls to it.
For a diagram of the voice mail port settings, see Figure 5.
Step 3 For all voice mail ports that answer calls on the primary server, set the Forward No Answer field to the first voice mail port on the secondary server.
If there are voice mail ports on the primary server that do not answer calls (for example, voice mail ports set only to Dialout MWI), set the Forward No Answer field to the first voice mail port on the primary server.
Caution In programming Cisco CallManager, do not send calls to ports in Cisco Unity that cannot answer calls (ports that are not set to Answer Calls). For example, if a port is set only to Dialout MWI, do not send calls to it.
For a diagram of the voice mail port settings, see Figure 5.
Step 4 For the last voice mail port that answers calls on the secondary server, set the Forward Busy and Forward No Answer fields to the first voice mail port on the secondary server.
If there are voice mail ports on the secondary server that do not answer calls (for example, voice mail ports set only to Dialout MWI), leave the Forward Busy field blank and set the Forward No Answer field to the first voice mail port on the secondary server.
Caution In programming Cisco CallManager, do not send calls to ports in Cisco Unity that cannot answer calls (ports that are not set to Answer Calls). For example, if a port is set only to Dialout MWI, do not send calls to it.
For a diagram of the voice mail port settings, see Figure 5.
Figure 5 Cisco CallManager Voice Mail Port Configuration for Cisco Unity Failover
To Set Up the Secondary Server for Failover
Step 1 Install a secondary server with the same configuration as the primary server. For installation instructions, refer to the Cisco Unity Installation Guide.
Step 2 On the Windows Start menu of the secondary server, click Programs > Cisco Unity > Manage Integrations. The UTIM window appears.
Step 3 On the Integration menu of the UTIM window, click New. The Telephony Integration Setup Wizard appears.
Step 4 Enter the settings to match the integration settings on the primary server.
Step 5 At the prompt to restart the Cisco Unity server, click Yes. The Cisco Unity server restarts.
Note When restarting Cisco Unity, use the UTIM prompt instead of the Cisco Unity icon in the Windows taskbar. The taskbar icon does not restart all of the Cisco Unity services.
Step 6 After Cisco Unity restarts, on the Windows Start menu of the Cisco Unity server, click Programs > Cisco Unity > Manage Integrations. UTIM appears.
Step 7 In the left pane of the UTIM window, click the phone system integration you created in Step 4.
Step 8 In the right pane of the UTIM window, click the Ports tab.
Step 9 Enter the port settings to match the port settings on the primary server.
Step 10 Click Save.
Step 11 Exit UTIM.
Changing the Settings for an Existing Integration
After the integration is set up, if you want to change any of its settings (for example, to change the MWI settings), do the following procedure.
If you want to change the number of voice messaging ports, see the "Changing the Number of Voice Messaging Ports" section.
To Change the Settings for an Integration
Step 1 On the Cisco Unity server, on the Windows Start menu, click Programs > Cisco Unity > Manage Integrations. The UTIM window appears.
Step 2 In the left pane, double-click Unity Server. The existing integrations appear.
Step 3 Click the integration you want to modify.
Step 4 In the right pane, click the cluster for the integration.
Step 5 In the right pane, click the applicable tab for the integration.
Step 6 Enter new settings in the fields that you want to change.
Caution If you are adding or removing voice messaging ports, make sure you change the settings for the individual ports so that there are an appropriate number of ports set to answer calls and an appropriate number of ports set to dial out.
Step 7 In the UTIM window, click Save.
Step 8 If prompted, restart the Cisco Unity services.
Changing the Number of Voice Messaging Ports
To change the number of voice messaging ports after you have finished installing and setting up Cisco CallManager, do the following procedures.
To Change the Number of Voice Messaging Ports in the Cisco CallManager Administration
Step 1 On the Cisco CallManager server, use the Cisco Voice Mail Port Wizard to add or remove voice messaging ports, as applicable.
For information on adding voice messaging ports, see the "To Add Voice Mail Ports to Cisco CallManager" section. For information on removing voice mail ports, refer to the Cisco CallManager Administrator Help.
Step 2 Continue with the next procedure.
To Update Cisco Unity for Additional Voice Messaging Ports
Step 1 If the Cisco Unity license does not enable the additional voice messaging ports you added, see your sales representative to request the applicable license.
Step 2 When you have the license, on the Cisco Unity server, click Programs > Cisco Unity > Licensing.
Step 3 On the Action menu, click Install License Files.
Step 4 Follow the on-screen instructions.
Note If you increase the number of voice messaging ports from 32 or fewer to more than 32, you must also install SQL Server 2000 as described in the Cisco Unity Installation Guide.
Step 5 Continue with the "Changing the Settings for an Existing Integration" section.
Deleting an Existing Integration
If you want to delete an existing integration (for example, you have replaced the phone system with which Cisco Unity originally integrated), do the following procedure.
To Delete an Existing Integration
Step 1 On the Cisco Unity server, on the Windows Start menu, click Programs > Cisco Unity > Manage Integrations. The UTIM window appears.
Step 2 In the left pane, double-click Unity Server. The existing integrations appear.
Step 3 Click the integration that you want to delete.
Step 4 On the Integration menu, click Delete.
Step 5 Follow the on-screen instructions to assign the subscribers of the deleted phone system integration to another phone system integration.
Step 6 At the prompt to restart the Cisco Unity services, click Yes. The Cisco Unity services restart.
Note When restarting Cisco Unity, use the UTIM prompt instead of the Cisco Unity icon in the Windows taskbar. The taskbar icon does not restart all of the Cisco Unity services.
Step 7 If the integration you deleted used voice cards, remove the voice cards from the Cisco Unity server.
Troubleshooting the Cisco CallManager Integration
This section provides information about common integration problems.
Cisco Unity Does Not Answer When the Extension for Cisco Unity Is Dialed
If you hear a fast busy or number unobtainable signal when you dial Cisco Unity, do the following procedure.
To Confirm That the Phone System Programming Is Complete
Step 1 Review the phone system programming to confirm that it is complete. Specific actions to take are:
•Confirming that the voice mail ports are correctly set up. For details, see the "To Add Voice Mail Ports to Cisco CallManager" section.
•Confirming that the voice mail ports and phones are in the same calling search space. For details, see the "To Add Voice Mail Ports to Cisco CallManager" section.
Step 2 Exit the Cisco Unity software, then restart the server.
Appendix: Using Alternate Extensions and MWIs
Alternate Extensions
In addition to the "primary" extension that you specify for subscribers, you can assign subscribers up to nine alternate extensions. (The primary extension is the one that you assign to each subscriber when you create his or her subscriber account; it is listed on the Subscribers > Subscribers > Profile page.)
Reasons to Use Alternate Extensions
There are several reasons why you may want to specify alternate extensions for subscribers. For example, if you have more than one Cisco Unity server that accesses a single, corporate-wide directory, you may want to use alternate extensions so that a subscriber uses the same number when addressing a message to a subscriber associated with another Cisco Unity server and when calling that subscriber directly. You may also want to use alternate extensions to:
•Handle multiple line appearances on subscriber phones.
•Offer easy message access on direct calls from a cell phone, home phone, or phone at an alternate work site (assuming that the phone number is passed along to Cisco Unity from these other phone systems). In addition, when such phones are used as alternate extensions, and are set to forward to Cisco Unity, callers can listen to the subscriber greeting, and leave messages for the subscriber just as they would when dialing the primary extension for the subscriber.
Tip To reduce the number of requests from subscribers who want alternate extensions set up for multiple cell phones, home phones, and other phones, give subscribers class of service (COS) rights to specify their own set of alternate extensions. (See the Subscribers > Class of Service > Profile page.) With proper COS rights, a subscriber can specify up to five alternate extensions in the Cisco Unity Assistant—in addition to the nine that you can specify on the Subscribers > Alternate Extensions page in the Cisco Unity Administrator.
•Simplify addressing messages to subscribers at different locations. With alternate extensions, the number that a subscriber uses when addressing a message to someone at another location can be the same number that the subscriber dials when calling.
•Enable URL-based extensions in Cisco Unity for an integration with a SIP phone system.
How Alternate Extensions Work
Before you set up alternate extensions, review the following list for information on how alternate extensions work:
•Alternate extensions cannot exceed 30 characters in length. By default, each administrator-defined alternate extension must be at least 3 characters in length, while subscriber-defined alternate extensions must be at least 10 characters.
You can use the Advanced Settings tool in Tools Depot to specify a minimum extension length for the extensions entered in the Cisco Unity Administrator and the Cisco Unity Assistant. Refer to the Advanced Settings Tool Help for details on using the settings. Respectively, the settings are Administration—Set the Minimum Length for Locations and Administration—Set the Minimum Length for Subscriber-Defined Alternate Extensions.
•You can control whether subscribers can use the Cisco Unity Assistant to view the alternate extensions that you specify in the Cisco Unity Administrator. To do so, see the Subscribers > Class of Service > Profile page. The Subscriber-Defined Alternate Extension table displays the alternate extensions that the subscriber adds.
•Neither the Cisco Unity Administrator nor the Cisco Unity Assistant will accept an extension that is already assigned to another subscriber (either as a primary or alternate extension), or to a public distribution list, call handler, directory handler, or interview handler. Cisco Unity verifies that each alternate extension is unique—up to the dialing domain level, if applicable—before allowing either an administrator or a subscriber to create it.
•All alternate extensions utilize the same transfer settings as the primary extension.
•In many cases, Cisco Unity can activate a message waiting indicator (MWI) for an alternate extension, though depending on the phones and phone systems involved, some additional phone system programming may be required to set this up.
Setting Up Alternate Extensions
Do the applicable procedure to add, modify, or delete alternate extensions:
•To Add Administrator-Defined Alternate Extensions
•To Modify or Delete Alternate Extension(s)
To Add Administrator-Defined Alternate Extensions
Step 1 In the Cisco Unity Administrator, go to any Subscribers > Alternate Extensions page.
Step 2 In the Administrator-Defined Alternate Extensions table, enter an extension in any row. When entering characters in the Alternate Extensions table, consider the following:
•You can enter an extension up to 30 characters in length. (SIP integrations can use up to 30 alphanumeric characters.)
•Each extension must be unique—up to the dialing domain level, if applicable.
•Enter digits 0 through 9. Do not use spaces, dashes, or parentheses.
•For SIP integrations, you can also enter a valid alias for a SIP URL. For example, if the URL is SIP:aabade@cisco.com, enter aabade. Do not use spaces.
•Rows are numbered as a convenience. You can enter alternate extensions in any order, and you can have blank rows.
Step 3 Repeat Step 2 as necessary.
Step 4 Click the Save icon. Alternate extensions are enabled for all rows in the table.
Note You can run the Cisco Unity Bulk Import wizard when you want to add alternate extensions for multiple subscribers at once. When you do, the Cisco Unity Bulk Import wizard appends the existing table of alternate extensions, beginning with the first blank row.
To Modify or Delete Alternate Extension(s)
Step 1 In the Cisco Unity Administrator, go to any Subscribers > Alternate Extensions page.
Step 2 Do any of the following:
•To modify an extension, change the extension in the Alternate Extensions table.
•To delete extensions, check the check boxes next to the alternate extensions that you want to delete.
•To remove all alternate extensions listed in the table, click Select All.
Step 3 Click the Save icon.
Step 4 Repeat Step 2 and Step 3 as necessary.
Alternate MWIs
You can set up Cisco Unity to activate alternate MWIs when you want a new message for a subscriber to activate the MWIs at up to 10 extensions. For example, a message left at extension 1001 can activate the MWIs on extensions 1001 and 1002.
Cisco Unity uses MWIs to alert the subscriber to new voice messages. MWIs are not used to indicate new e-mail, fax, or return receipt messages.
In Cisco CallManager integrations, you can also use the alternate MWI feature to activate MWIs on a non-integrated phone system that can send and receive information from Cisco Unity over an RS-232 serial cable.
This section contains the following information:
•Setting Up Alternate MWIs for Extensions on the Same Phone System
•MWIs for Extensions on a Non-Integrated Phone System
•Setting Up MWIs for Extensions on a Non-Integrated Phone System
Setting Up Alternate MWIs for Extensions on the Same Phone System
Cisco Unity can activate alternate MWIs for extensions on the same phone system. Note that depending on the phones and phone systems, some additional phone system programming may be necessary. Refer to the installation guide for the phone system.
To enable alternate MWIs for extensions on the same phone system, do the following procedure for each subscriber who needs alternate MWIs.
To Set Up Alternate MWIs for Extensions on the Same Phone System
Step 1 In the Cisco Unity Administrator, go to the applicable Subscribers > Subscribers > Messages page.
Step 2 Confirm that the Use MWI for Message Notification check box is checked.
Step 3 Click the Add button located beneath the MWI Extensions table to add a row to the table. By default, the first row in the table contains an "X" to indicate the primary extension assigned to a subscriber. If you want one more extension and do not need to activate the MWI on the primary extension, you can also modify the first row.
Step 4 Enter the applicable extension in the Extension field of the table. MWIs are automatically enabled for all rows in the table. When entering characters in the MWI Extensions table, consider the following:
•Enter digits 0 through 9. Do not use spaces, dashes, or parentheses.
•Enter , (comma) to insert a one-second pause.
•Enter # and * to correspond to the # and * keys on the phone.
Step 5 Click the Save icon.
Step 6 Repeat Step 3 through Step 5 as necessary.
Note You can run the Cisco Unity Bulk Import wizard when you want to set up alternate MWIs for multiple subscribers at once.
To change or delete alternate MWIs for extensions, do the following procedure.
To Modify or Delete Alternate MWIs
Step 1 In the Cisco Unity Administrator, go to the applicable Subscribers > Subscribers > Messages page.
Step 2 Do either of the following:
•To modify an extension, change the extension in the MWI Extensions table.
•To delete extensions, check the check boxes next to the rows that you want to delete in the MWI Extensions table, and then click the Delete button.
Step 3 Click the Save icon.
Step 4 Repeat Step 2 and Step 3 as necessary.
MWIs for Extensions on a Non-Integrated Phone System
Cisco Unity can activate MWIs on a phone system that is not integrated with Cisco Unity and that is not part of a dual phone system integration (referred to here as a non-integrated phone system). MWI activation requests are sent through an RS-232 serial cable.
For this method, you must set up:
•A trunk connection between Cisco CallManager and the non-integrated phone system through a gateway.
•The unique subscriber extensions on the non-integrated phone system to forward on no answer to the corresponding phantom extensions on Cisco CallManager.
•The Switch.ini file (phone system configuration file) to enable Cisco Unity access through the serial cable for turning alternate MWIs on and off.
•An RS-232 serial cable between a Cisco Unity serial port and the non-integrated phone system serial port to send alternate MWI activation requests.
•The Cisco Unity serial configuration file, if the non-integrated phone system uses a serial configuration different from the default serial configuration used by Cisco Unity.
Figure 6 shows the connections via a serial cable between a Cisco CallManager integration and a non-integrated phone system.
Figure 6 Connection for Sending Alternate MWIs via a Serial Cable to a Non-Integrated Phone System from a Cisco CallManager Integration
Calls to subscribers that come from the non-integrated phone system are routed through the gateway to Cisco CallManager.
Setting Up MWIs for Extensions on a Non-Integrated Phone System
To set up MWIs for extensions on a non-integrated phone system, do the following applicable procedures.
To Set Up MWIs on a Non-Integrated Phone System
Step 1 Set up a trunk connection between the non-integrated phone system and Cisco CallManager through the gateway.
Step 2 In the Cisco Unity Administrator, set up the subscriber for the phantom extension, making use of the subscriber information from the corresponding extension on the non-integrated phone system, including the following settings:
•On the Subscriber > Profile page for the subscriber, in the Extension field, enter the corresponding extension on the non-integrated phone system.
•On the Subscriber > Call Transfer page for the subscriber, under Transfer Incoming Calls, click No.
•On the Subscriber > Messages page for the subscriber, confirm that the Use MWI for Message Notification check box is checked.
•On the Subscriber > Messages page for the subscriber, under MWI Extensions, delete the "X" and enter ZX.
Step 3 In the Cisco Unity Administrator, click the Save icon.
To Revise the Switch.ini File
Step 1 On the Windows Start menu, click Programs > Cisco Unity > Manage Integrations. UTIM appears.
Step 2 In the left pane of the UTIM window, click the Cisco CallManager integration, and click the Properties node. The Properties tab appears in the right pane of the UTIM window.
Step 3 Note the name of the Switch.ini file that appears in the Configuration File field.
Step 4 Exit UTIM.
Step 5 On the Windows Start menu, click Programs > Accessories > Notepad. The Notepad window appears.
Step 6 On the File menu, click Open.
Step 7 In the Open window, navigate to the CommServer\IntLib directory, and double-click the name of the Switch.ini file you noted in Step 3.
Step 8 Add a new section at the end of the file to contain the following lines. For detailed information about the settings, see Table 18.
[Alternate MWI]Active=YesDigit=ZMWIType=SerialSerialConfiguration=<if applicable, the type of serial configuration for the connection>
Step 9 Save the file, and exit Notepad.
Do the following procedure if the serial configuration used by the non-integrated phone system is different from the default serial configuration that Cisco Unity uses.
To Revise the Cisco Unity Serial Configuration File
Step 1 On the Windows Start menu, click Programs > Accessories > Notepad. The Notepad window appears.
Step 2 On the File menu, click Open.
Step 3 In the Open window, navigate to the CommServer\IntLib directory, and double-click the file corresponding to the serial configuration you are using to activate alternate MWIs:
•Avsmdi.avd
•Avmci.avd
•Avinte.avd
•Averic.avd
Step 4 Under the [Configuration] divider, revise the settings to match the configuration required by the non-integrated phone system. Refer to the phone system and its documentation for this information.
Step 5 Save the file, and exit Notepad.
Appendix: Documentation and Technical Assistance
Conventions
The Cisco CallManager 3.2 Integration Guide for Cisco Unity 4.0 uses the following conventions.
The Cisco CallManager 3.2 Integration Guide for Cisco Unity 4.0 also uses the following conventions:
Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.
Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.
Cisco Unity Documentation
For descriptions and URLs of Cisco Unity documentation on Cisco.com, refer to About Cisco Unity Documentation. The document is shipped with Cisco Unity and is available at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_unity/about/aboutdoc.htm.
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation on the World Wide Web at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
International Cisco websites can be accessed from this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can submit e-mail comments about technical documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services, online and over the phone. Cisco.com features the Cisco Technical Support website as an online starting point for technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco Technical Support website is available 24 hours a day, 365 days a year. The Cisco Technical Support website is located at this URL:
Accessing all the tools on the Cisco Technical Support website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a login ID or password, register at this URL:
http://tools.cisco.com/RPF/register/register.do
Opening a TAC Case
Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Case Open Tool automatically recommends resources for an immediate solution. If your issue is not resolved using the recommended resources, your case will be assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:
http://www.cisco.com/tac/caseopen
For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.
To open a case by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447For a complete listing of Cisco TAC contacts, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
TAC Case Priority Definitions
To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.
Priority 1 (P1)—Your network is "down" or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.
Priority 3 (P3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.
Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online and printed sources.
•Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Go to this URL to visit the company store:
http://www.cisco.com/go/marketplace/
•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press online at this URL:
•Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources. You can access Packet magazine at this URL:
•iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:
•Training—Cisco offers world-class networking training. Current offerings in network training are listed at this URL:
http://www.cisco.com/en/US/learning/index.html
Copyright © 2004 Cisco Systems, Inc. All rights reserved.