Table Of Contents
Cisco Unified MeetingPlace Audio Server Software Installation and Upgrade Reference
Viewing the Remote Installation or Upgrade for a Sample Session without a Disk Backup
Viewing the Upgrade Status for a Remote Installation or Upgrade Session
Viewing the Real-time Upgrade Status for a Remote Installation or Upgrade Session
Viewing the Onsite Installation or Upgrade for a Sample Session without a Disk Backup
Viewing the Onsite Installation or Upgrade for a Sample Session with a Disk Backup
Cisco Unified MeetingPlace Audio Server Software Installation and Upgrade Reference
This appendix contains sample sessions of upgrading the Cisco Unified MeetingPlace Audio Server software. The procedures for installing and upgrading the software are located in "Installing and Upgrading the Cisco Unified MeetingPlace Audio Server Software." The following sections are useful to refer to when you are installing or upgrading the software so that you will know how far in the process you are.
•Viewing the Remote Installation or Upgrade for a Sample Session without a Disk Backup
•Viewing the Upgrade Status for a Remote Installation or Upgrade Session
•Viewing the Real-time Upgrade Status for a Remote Installation or Upgrade Session
•Viewing the Onsite Installation or Upgrade for a Sample Session without a Disk Backup
•Viewing the Onsite Installation or Upgrade for a Sample Session with a Disk Backup
Viewing the Remote Installation or Upgrade for a Sample Session without a Disk Backup
Checking to see if the system is loaded...OK
System DOWN procedure has been initiated.
Please insert the update CD in the drive, then
wait for the drive to be quiet before continuing.
Press <ENTER> to continue or <CONTROL-C> to abort.
CD mounted OK; checking for update sets...
There is just one update set on the CD.
You wish to install: MeetingPlace 5.3
Is this correct? (y or n) y
---------------------------------------------------------------
- MeetingPlace software release 5.3
- Archive created: Fri Oct 2913:51:39 PDT 2004
---------------------------------------------------------------
Press <ENTER> to continue or <CONTROL-C> to abort.
Mon Oct 26 14:20:41 PDT 2004 Starting ./UPDATE.phase1
Mon Oct 26 14:20:41 PDT 2004 Verifying the tape image checksum
Mon Oct 26 14:20:49 PDT 2004 Killing cron
Mon Oct 26 14:20:50 PDT 2004 Copying root file system from partition 1a to 2a
Mon Oct 26 14:21:35 PDT 2004 Starting extraction of files from archive:
Mon Oct 26 14:22:55 PDT 2004 Archive extraction is done.
Mon Oct 26 14:22:55 PDT 2004 Resetting system file ownerships:
Mon Oct 26 14:22:55 PDT 2004 Removing set-uid permissions:
Mon Oct 26 14:22:55 PDT 2004 Updating files and setting permissions:
Mon Oct 26 14:22:59 PDT 2004 Replacing .//lat/sys/drivers/falcon/falcon_detach with
.//lat/sys/drivers/falcon/falcon_attach
Mon Oct 26 14:23:00 PDT 2004 Replacing .//bin/less with .//lat/etc/less
Mon Oct 26 14:23:00 PDT 2004 Replacing .//bin/login with .//lat/etc/bin.login
Mon Oct 26 14:23:00 PDT 2004 Replacing .//bin/rsh with .//lat/etc/rsh
Mon Oct 26 14:23:00 PDT 2004 Replacing .//etc/motd with .//lat/etc/etc.motd
Mon Oct 26 14:23:00 PDT 2004 Replacing .//lat/bin/dp with .//lat/etc/rsh
Mon Oct 26 14:23:00 PDT 2004 Replacing .//lat/bin/updatefile with .//lat/etc/runscr
Mon Oct 26 14:23:00 PDT 2004 Replacing .//lat/etc/setup_CSdb with .//lat/etc/runscr
Mon Oct 26 14:23:00 PDT 2004 Replacing .//lat/bin/clearshmem with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/configdiskcap with
.//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/diskcopy with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/download with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/mpconvert with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/newdisk with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/revert with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/restore with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/restore_vp_db with
.//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/save with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/sysconfig with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/sysdatacopy with .//lat/etc/runscr
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/su with .//lat/etc/su
Mon Oct 26 14:23:01 PDT 2004 Replacing .//lat/techbin/update with .//lat/etc/runscr
Mon Oct 26 14:23:03 PDT 2004 Replacing .//bin/xntpd with .//lat/etc/xntpd
Mon Oct 26 14:23:03 PDT 2004 Replacing .//net/inetd with .//lat/etc/inetd
Mon Oct 26 14:23:03 PDT 2004 Replacing .//net/telnetd with .//lat/etc/telnetd
Mon Oct 26 14:23:03 PDT 2004 Replacing .//lynx.os with .//lat/etc/lynx.os
Mon Oct 26 14:23:04 PDT 2004 Updating time zone files:
Mon Oct 26 14:23:05 PDT 2004 Installing the new OS files
Mon Oct 26 14:23:08 PDT 2004 Constructing a new prompt set on partition 2f
Mon Oct 26 14:23:17 PDT 2004 Constructed new alternate prompt set
Mon Oct 26 14:23:17 PDT 2004 Copying in the new prompt set
Mon Oct 26 14:23:34 PDT 2004 Prompt setup complete
Mon Oct 26 14:23:34 PDT 2004 Copying the active database into a fresh partition
Mon Oct 26 14:23:34 PDT 2004 Constructing a new database on partition 2e
Mon Oct 26 14:28:51 PDT 2004 New database construction is complete
Mon Oct 26 14:28:52 PDT 2004 Preparing the boot from the new software load
The first phase of the software upgrade is complete.
The system will now restart. As it comes up it will start the 2nd phase
Viewing the Upgrade Status for a Remote Installation or Upgrade Session
Release 5.3, Oct 26, 2004
Last login: Mon Oct 26 19:31:14 from Unknown-HostName
*************************************************************************
* Copyright (c) 1993-2004 Cisco Systems *
*************************************************************************
Conference server 5.3 S/N: not set
Mon Oct 26 19:55:58 PDT 2004
Last status update: Oct 26 19:56
Building the deleted record database
Last status update: Oct 26 19:56
Upgrade phase 2: Database revision complete; almost done
Viewing the Real-time Upgrade Status for a Remote Installation or Upgrade Session
Release 5.3, Oct 26, 2004
Last login: Mon Oct 26 19:31:14 from Unknown-HostName
*************************************************************************
* Copyright (c) 1993-2004 Cisco Systems*
*************************************************************************
Conference server 5.3 S/N: not set
Mon Oct 26 19:55:58 PDT 2004
Last update: Oct 26 19:56
----------- Preallocating db Mon Oct 26 19:55:19 PDT 2004
Reserving 100 db records (code 10000) ...
the db file already has 1 16384 byte pages that can hold 143 record(s)
Reserving 200 dbclass records (code 10001) ...
Adding 2 16384 byte page(s) to get 127 record(s) ...
Reserving 200 dbmember records (code 10002) ...
Adding 1 16384 byte page(s) to get 200 record(s) ...
Pre-allocating each key file...
Adding 3 16384 byte pages to key file db.name...
Adding 3 16384 byte pages to key file dbclass.dbnamerecid...
Adding 5 16384 byte pages to key file dbclass.csdbnameskey...
Adding 3 16384 byte pages to key file dbclass.dbname...
Adding 3 16384 byte pages to key file dbclass.classname...
Adding 3 16384 byte pages to key file dbmember.fieldid...
----------- db preallocation complete Mon Oct 26 19:55:19 PDT 2004
----------- Preallocating deletedrec Mon Oct 26 19:55:19 PDT 20043
Reserving 1000000 deletedrec records (code 10000) ...
the deletedrec file already has 1000000 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file deletedrec.Sequence...
----------- deletedrec preallocation complete Mon Oct 26 19:55:19 PDT 2004
----------- Preallocating flexmenu Mon Oct 26 19:55:19 PDT 2004
Record 10000 (FMAppRec): has no preallocation count
Record 10001 (FMStateTable): has no preallocation count
Record 10002 (CustAppPrompt): has no preallocation count
Record 10003 (FMPlayPrompt): has no preallocation count
Record 10004 (FMGotoApp): has no preallocation count
Record 10005 (FMOptionMenu): has no preallocation count
Record 10006 (FMHangUp): has no preallocation count
Record 10007 (FMFindMtg): has no preallocation count
Record 10008 (FMReviewMtgMat): has no preallocation count
Record 10009 (FMGetProfile): has no preallocation count
Pre-allocating each key file...
----------- flexmenu preallocation complete Mon Oct 26 19:55:21 PDT 2004
----------- Preallocating gen Mon Oct 26 19:55:21 PDT 2004
Reserving 250000 user records (code 10002) ...
the user file already has 19231 16384 byte pages that can hold 250003 record(s)
Reserving 100 group records (code 10000) ...
the group file already has 3 16384 byte pages that can hold 117 record(s)
Record 10003 (gentmp1): has no preallocation count
Record 10005 (gentmp2): has no preallocation count
Record 10004 (gentmp3): has no preallocation count
Reserving 6 flexfield records (code 10001) ...
the flexfield file already has 14 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file user.last...
Adding 2 16384 byte pages to key file user.name...
Adding 2 16384 byte pages to key file user.uniqueid...
Adding 2 16384 byte pages to key file user.username...
Adding 2 16384 byte pages to key file user.cuid...
Adding 2 16384 byte pages to key file user.cnlf...
Adding 2 16384 byte pages to key file user.lfn...
Adding 2 16384 byte pages to key file user.in...
Adding 2 16384 byte pages to key file user.vuname...
Adding 2 16384 byte pages to key file user.glfn...
Adding 2 16384 byte pages to key file user.UpdateTime...
----------- gen preallocation complete Mon Oct 26 19:55:21 PDT 2004
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
----------- Preallocating pegs Mon Oct 26 19:55:21 PDT 2004
Reserving 1 pegs records (code 10000) ...
the pegs file already has 1536 record(s)
Pre-allocating each key file...
----------- pegs preallocation complete Mon Oct 26 19:55:21 PDT 2004
----------- Preallocating podata Mon Oct 26 19:55:21 PDT 2004
Reserving 1 pomailbox records (code 10000) ...
the pomailbox file already has 32 record(s)
Reserving 20000 pomsgdata records (code 10001) ...
Pre-allocating each key file...
Adding 2 16384 byte pages to key file pomsgdata.compundkey...
----------- podata preallocation complete Mon Oct 26 19:55:21 PDT 2004
----------- Preallocating res Mon Oct 6 19:55:21 PDT 2003
Reserving 1 crres records (code 10004) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 1 portres records (code 10005) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 200000 didres records (code 10001) ...
Adding 513 16384 byte page(s) to get 200000 record(s) ...
Record 10000 (didconfigres): has no preallocation count
Record 10003 (schedparamsres): has no preallocation count
Reserving 13 crresfstaccess records (code 10006) ...
the crresfstaccess file already has 13 record(s)
Reserving 13 portresfstaccess records (code 10007) ...
the portresfstaccess file already has 13 record(s)
Reserving 13 vsresfstaccess records (code 10008) ...
the vsresfstaccess file already has 15 record(s)
Reserving 200000 vsres records (code 10002) ...
Adding 465 16384 byte page(s) to get 200000 record(s) ...
Pre-allocating each key file...
Adding 635 16384 byte pages to key file didres.strtdid...
Adding 343 16384 byte pages to key file didres.UpdateTime...
Adding 3 16384 byte pages to key file crres.resourceid...
Adding 3 16384 byte pages to key file portres.resourceid...
Adding 343 16384 byte pages to key file vsres.resourceid...
Adding 343 16384 byte pages to key file vsres.UpdateTime...
----------- res preallocation complete Mon Oct 26 19:55:26 PDT 2004
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
----------- Preallocating status Mon Oct 26 19:55:26 PDT 2004
Reserving 200 alarmentry records (code 10000) ...
the alarmentry file already has 200 record(s)
Reserving 16384 exlogentry records (code 10001) ...
the exlogentry file already has 16384 record(s)
Reserving 1 hwstatus records (code 10002) ...
the hwstatus file already has 1 16384 byte pages that can hold 2047 record(s)
Reserving 1 swstatus records (code 10003) ...
the swstatus file already has 1 record(s)
Reserving 1500 exlogformat records (code 10004) ...
the exlogformat file already has 3374 record(s)
Reserving 20 apps records (code 10005) ...
the apps file already has 21 record(s)
Reserving 10000 outdial records (code 10006) ...
the outdial file already has 10000 record(s)
Reserving 10000 notification records (code 10007) ...
the notification file already has 10000 record(s)
Record 10008 (schedfail): has no preallocation count
Record 10009 (gwstatus): has no preallocation count
Pre-allocating each key file...
----------- status preallocation complete Mon Oct 26 19:55:26 PDT 2004
----------- Preallocating tcnfg Mon Oct 26 19:55:26 PDT 2004
Reserving 100 analogcard records (code 10000) ...
the analogcard file already has 1 16384 byte pages that can hold 431 record(s)
Reserving 1 masterswcard records (code 10001) ...
the masterswcard file already has 108 record(s)
Reserving 100 portrescard records (code 10002) ...
the portrescard file already has 108 record(s)
Reserving 100 t1card records (code 10003) ...
the t1card file already has 108 record(s)
Reserving 10 t1span records (code 10004) ...
the t1span file already has 432 record(s)
Reserving 1000 trunk records (code 10005) ...
the trunk file already has 10800 record(s)
Reserving 100 trunkgroup records (code 10006) ...
the trunkgroup file already has 1 16384 byte pages that can hold 110 record(s)
Reserving 100 e1card records (code 10007) ...
the e1card file already has 1 16384 byte pages that can hold 163 record(s)
Reserving 10 e1span records (code 10008) ...
the e1span file already has 36 record(s)
Record 10009 (accard): has no preallocation count
Record 10010 (acspan): has no preallocation count
Record 10012 (iprescard): has no preallocation count
Record 10013 (blade): has no preallocation count
Record 10014 (prottable): has no preallocation count
Record 10011 (ipglobalcfg): has no preallocation count
Pre-allocating each key file...
Adding 3 16384 byte pages to key file analogcard.unitid...
Adding 3 16384 byte pages to key file masterswcard.unitid...
Adding 3 16384 byte pages to key file portrescard.unitid...
Adding 3 16384 byte pages to key file t1card.unitid...
Adding 3 16384 byte pages to key file t1span.unitid...
Adding 3 16384 byte pages to key file trunkgroup.id...
Adding 3 16384 byte pages to key file e1card.unitid...
Adding 3 16384 byte pages to key file e1span.unitid...
----------- tcnfg preallocation complete Mon Oct 26 19:55:27 PDT 2004
----------- Preallocating userlist Mon Oct 26 19:55:27 PDT 2004
Reserving 100000 userlist records (code 10000) ...
the userlist file already has 2041 16384 byte pages that can hold 100009 record(s)
Reserving 500000 userlistmem records (code 10001) ...
the userlistmem file already has 611 16384 byte pages that can hold 500409 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file userlist.uniqueid...
Adding 2 16384 byte pages to key file userlist.vuiid...
Adding 2 16384 byte pages to key file userlist.name...
Adding 2 16384 byte pages to key file userlist.unta...
Adding 2 16384 byte pages to key file userlist.UpdateTime...
Adding 2 16384 byte pages to key file userlist.oulid...
Adding 2 16384 byte pages to key file userlistmem.uluid...
Adding 2 16384 byte pages to key file userlistmem.UpdateTime...
----------- userlist preallocation complete Mon Oct 26 19:55:27 PDT 2004
cmdbrev: starting delrecinit
There are supposed to be 1000000 records in the deleted record database
Counting the number of records in the database...
cmdbrev: ending Mon Oct 26 19:56:08 PDT 2004
Mon Oct 26 19:56:08 PDT 2004 Network setup:
Unit class = SINGLE/LOCAL
Updating error log format strings: Using database path: /lat/db/status
48 new entries and 3375 replacements
Prompt Upgrade>> Opening file </lat/fs.1/prompt_db_vfs_map_dir0> ....
Number Of Language(s) in the prompt map file: 1
Prompt Upgrade>> EOF (0) reached in /lat/fs.1/prompt_db_vfs_map_dir0 file (promptNum
1551): 0
... Done with English (US)
Starting Update Company Info
The languages installed are:
Language 1 dir0 English (US)
FINISHED: Prompt Database Upgrade is complete!
Statistics: 0 new entries and 319 replacements
Updating time zone names: Using database path: /lat/db/config
Updating option names ... ... Done
Setting prompt file configuration
The file system directories are already updated
The file system directories are already updated
The file system directories are already updated
Adjusting prompt file sizes
Initializing the file system...
Getting the disk configuration status...
Checking file system internal consistency... (may take a while) ...
Mon Oct 26 19:56:15 PDT 2004 NOTE: Disk backups disabled; run 'save' to re-enable.
Mon Oct 2 6 19:56:15 PDT 2004 Software update is complete.
Viewing the Onsite Installation or Upgrade for a Sample Session without a Disk Backup
Please insert the update CD in the drive, then
wait for the drive to be quiet before continuing.
Press <ENTER> to continue or <CONTROL-C> to abort.
CD mounted OK; checking for update sets...
There is just one update set on the CD.
You wish to install: MeetingPlace 5.3
Is this correct? (y or n) y
---------------------------------------------------------------
- MeetingPlace software release 5.3
- Archive created: Fri Oct 29 13:51:39 PDT 2004
---------------------------------------------------------------
Press <ENTER> to continue or <CONTROL-C> to abort.
Mon Oct 26 18:50:22 PDT 2004 Starting ./UPDATE.phase1
Mon Oct 26 18:50:22 PDT 2004 Verifying the tape image checksum
Mon Oct 26 18:50:30 PDT 2004 Killing cron
Mon Oct 26 18:50:31 PDT 2004 Copying root file system from partition 1a to 2a
Mon Oct 26 18:51:17 PDT 2004 Starting extraction of files from archive:
Mon Oct 26 18:52:31 PDT 2004 Archive extraction is done.
Mon Oct 26 18:52:31 PDT 2004 Resetting system file ownerships:
Mon Oct 26 18:52:31 PDT 2004 Removing set-uid permissions:
Mon Oct 26 18:52:31 PDT 2004 Updating files and setting permissions:
Mon Oct 26 18:52:35 PDT 2004 Replacing .//lat/sys/drivers/falcon/falcon_detach with
.//lat/sys/drivers/falcon/falcon_attach
Mon Oct 26 18:52:36 PDT 2004 Replacing .//bin/less with .//lat/etc/less
Mon Oct 26 18:52:36 PDT 2004 Replacing .//bin/login with .//lat/etc/bin.login
Mon Oct 26 18:52:36 PDT 2004 Replacing .//bin/rsh with .//lat/etc/rsh
Mon Oct 26 18:52:36 PDT 2004 Replacing .//etc/motd with .//lat/etc/etc.motd
Mon Oct 26 18:52:36 PDT 2004 Replacing .//lat/bin/dp with .//lat/etc/rsh
Mon Oct 26 18:52:36 PDT 2004 Replacing .//lat/bin/updatefile with .//lat/etc/runscr
Mon Oct 26 18:52:36 PDT 2004 Replacing .//lat/etc/setup_CSdb with .//lat/etc/runscr
Mon Oct 26 18:52:36 PDT 2004 Replacing .//lat/bin/clearshmem with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/configdiskcap with
.//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/diskcopy with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/download with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/mpconvert with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/newdisk with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/revert with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/restore with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/restore_vp_db with
.//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/save with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/sysconfig with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/sysdatacopy with .//lat/etc/runscr
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/su with .//lat/etc/su
Mon Oct 26 18:52:37 PDT 2004 Replacing .//lat/techbin/update with .//lat/etc/runscr
Mon Oct 26 18:52:39 PDT 2004 Replacing .//bin/xntpd with .//lat/etc/xntpd
Mon Oct 26 18:52:39 PDT 2004 Replacing .//net/inetd with .//lat/etc/inetd
Mon Oct 26 18:52:39 PDT 2004 Replacing .//net/telnetd with .//lat/etc/telnetd
Mon Oct 26 18:52:39 PDT 2004 Replacing .//lynx.os with .//lat/etc/lynx.os
Mon Oct 26 18:52:40 PDT 2004 Updating time zone files:
Mon Oct 26 18:52:41 PDT 2004 Installing the new OS files
Mon Oct 26 18:52:43 PDT 2004 Constructing a new prompt set on partition 2f
Mon Oct 26 18:52:53 PDT 2004 Constructed new alternate prompt set
Mon Oct 26 18:52:53 PDT 2004 Copying in the new prompt set
Mon Oct 26 18:53:44 PDT 2004 Prompt setup complete
Mon Oct 26 18:53:44 PDT 2004 Copying the active database into a fresh partition
Mon Oct 26 18:53:44 PDT 2004 Constructing a new database on partition 2c
Mon Oct 26 18:59:02 PDT 2004 New database construction is complete
Mon Oct 26 18:59:03 PDT 2004 Preparing the boot from the new software load
The first phase of the software upgrade is complete.
The system will now restart. As it comes up it will start the 2nd phase
LynxOS 386/486/Pentium PC-AT Version 3.1.0
Copyright 1987-1998 Lynx Real-Time Systems Inc.
LynxOS (x86) created Tue Sep 30 15:05:41 PDT 2003
Rebooting into multi-user mode in 5 seconds...
LynxOS 386/486/Pentium PC-AT Version 3.1.0
Copyright 1987-1998 Lynx Real-Time Systems Inc.
LynxOS (x86) created Tue Sep 30 15:05:41 PDT 2003
MeetingPlace by Cisco Systems
Mon Oct 26 19:01:07 PDT 2004
(all sizes and block numbers in decimal)
(file system is byte-swapped)
(file system creation time is Mon Oct 26 18:50:30 2004)
(file system contains 31999 blocks and 7936 inodes)
checking for orphaned files
making bit map free block list
14624 free blocks 6080 free inodes
Copying /tmp FS from partition 2b to 1b
/tmp moved to /dev/disk1b
Unit class is standalone conference server (SINGLE).
Bus architecture is CompactPCI (M3).
Ethernet device is "pro0".
Initializing the modem on COM2.../lat/bin/initmodem ...
/lat/bin/initmodem: type is `MultiTech MT5634Z'
/lat/bin/initmodem: modem initialized
Installing Cisco drivers...
devinstall: acti.dat: Device doesn't exist
Executing the 2nd stage of software upgrade.
Mon Oct 26 19:01:44 PDT 2004 Phase 2 starting
Revising database from 5.2.0 to 5.3
cmdbrev: begun Mon Oct 26 19:01:44 PDT 2004
Mon Oct 26 19:01:44 PDT 2004
cmdbrev: starting /lat/bin/initdb -y 5.2.0/config
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/initdb done
Beginning dbrev at Mon Oct 26 19:01:44 PDT 2004
cmdbrev: starting /lat/bin/dbrev -s 5.2.0/config.rdl -q -v /lat/db/config 5.2.0/config
line 22: field CSSYSTEMCONFIG.MAXMEETINGIDLENGT not contained in destination database
dbrev compilation complete
Processing file /lat/db/billinginfo containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/companyinfo containing 1 records
Current slot 1 (0 seconds)
Processing file /lat/db/filestats containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/hwconfig containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/hwstats containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/option containing 22 records
Current slot 22 (0 seconds)
Processing file /lat/db/outdialtrans containing 16 records
Current slot 16 (0 seconds)
Processing file /lat/db/netmgtinfo containing 1 records
Current slot 1 (0 seconds)
Processing file /lat/db/netmgtcomm containing 3 records
Current slot 3 (0 seconds)
Processing file /lat/db/unit containing 128 records
Current slot 128 (0 seconds)
Processing file /lat/db/site containing 8 records
Current slot 8 (0 seconds)
Processing file /lat/db/promptstats containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/scsi containing 128 records
Current slot 128 (0 seconds)
Processing file /lat/db/swconfig containing 1 records
Current slot 1 (0 seconds)
Processing file /lat/db/swstats containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/systemconfig containing 1 records
Current slot 1 (0 seconds)
Processing file /lat/db/timezone containing 319 records
Current slot 319 (0 seconds)
Processing file /lat/db/mtgcategory containing 1 records
Current slot 1 (0 seconds)
Processing file /lat/db/remoteserver containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/didcnfgconfig containing 16 records
Current slot 16 (0 seconds)
Processing file /lat/db/schedparamsconfig containing 1 records
Current slot 1 (0 seconds)
dbrev completed, successful restructure
Database Restructure Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/dbrev done
Copying 5.2.0/billinginfo:
Copying 5.2.0/companyinfo:
Copying 5.2.0/outdialtrans:
Copying 5.2.0/netmgtinfo:
Copying 5.2.0/netmgtcomm:
Copying 5.2.0/promptstats:
Copying 5.2.0/systemconfig:
Copying 5.2.0/mtgcategory:
Copying 5.2.0/remoteserver:
Copying 5.2.0/didcnfgconfig:
Copying 5.2.0/schedparamsconfig:
Copying 5.2.0/filestats.recnum:
Copying 5.2.0/netmgtcomm.name:
Copying 5.2.0/outdialtrans.recnum:
Copying 5.2.0/option.name:
Copying 5.2.0/timezone.id:
Copying 5.2.0/timezone.timezonekey:
Copying 5.2.0/unit.unitnum:
Copying 5.2.0/site.sitenum:
Copying 5.2.0/scsi.unitid:
Copying 5.2.0/mtgcategory.uniqueid:
Copying 5.2.0/mtgcategory.name:
Copying 5.2.0/mtgcategory.mtgcatkey:
Copying 5.2.0/remoteserver.uniqueid:
Copying 5.2.0/remoteserver.name:
Copying 5.2.0/remoteserver.vuiid:
Copying 5.2.0/remoteserver.ether:
Copying 5.2.0/didcnfgconfig.unitnum:
cmdbrev: starting /lat/bin/initdb -y 5.2.0/config
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/initdb done
cmdbrev: starting /lat/bin/initdb -y 5.2.0/res
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/initdb done
Beginning dbrev at Mon Oct 26 19:01:47 PDT 2004
cmdbrev: starting /lat/bin/dbrev -q -v /lat/db/res 5.2.0/res
dbrev compilation complete
Processing file /lat/db/crres containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/portres containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/didres containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/didconfigres containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/schedparamsres containing 0 records
Current slot 0 (0 seconds)
Processing file /lat/db/crresfstaccess containing 13 records
Current slot 13 (0 seconds)
Processing file /lat/db/portresfstaccess containing 13 records
Current slot 13 (0 seconds)
Processing file /lat/db/vsresfstaccess containing 15 records
Current slot 15 (0 seconds)
Processing file /lat/db/vsres containing 0 records
Current slot 0 (0 seconds)
dbrev completed, successful restructure
Database Restructure Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/dbrev done
Copying 5.2.0/didconfigres:
Copying 5.2.0/schedparamsres:
Copying 5.2.0/crresfstaccess:
Copying 5.2.0/portresfstaccess:
Copying 5.2.0/vsresfstaccess:
Copying 5.2.0/didconfigres.unitnum:
Copying 5.2.0/didres.strtdid:
Copying 5.2.0/didres.UpdateTime:
Copying 5.2.0/crres.resourceid:
Copying 5.2.0/portres.resourceid:
Copying 5.2.0/vsres.resourceid:
Copying 5.2.0/vsres.UpdateTime:
cmdbrev: starting /lat/bin/initdb -y 5.2.0/res
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/initdb done
cmdbrev: starting /lat/bin/initdb -y 5.2.0/tcnfg
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/initdb done
Beginning dbrev at Mon Oct 26 19:01:48 PDT 2004
cmdbrev: starting /lat/bin/dbrev -q -v /lat/db/tcnfg 5.2.0/tcnfg
dbrev compilation complete
Processing file /lat/db/analogcard containing 45 records
Current slot 45 (0 seconds)
Processing file /lat/db/masterswcard containing 108 records
Current slot 108 (0 seconds)
Processing file /lat/db/portrescard containing 108 records
Current slot 108 (0 seconds)
Processing file /lat/db/t1card containing 108 records
Current slot 108 (0 seconds)
Processing file /lat/db/t1span containing 432 records
Current slot 432 (0 seconds)
Processing file /lat/db/trunk containing 10800 records
Current slot 1000 (0 seconds) Current slot 2000 (0 seconds) Current slot 3000 (1 seconds)
Current slot 4000 (1 seconds) Current slot 5000 (1 seconds) Current slot 6000 (1 seconds)
Current slot 7000 (1 seconds) Current slot 8000 (1 seconds) Current slot 9000 (2 seconds)
Current slot 10000 (2 seconds) Current slot 10800 (2 seconds)
Processing file /lat/db/trunkgroup containing 32 records
Current slot 32 (0 seconds)
Processing file /lat/db/e1card containing 18 records
Current slot 18 (0 seconds)
Processing file /lat/db/e1span containing 36 records
Current slot 36 (0 seconds)
Processing file /lat/db/accard containing 27 records
Current slot 27 (0 seconds)
Processing file /lat/db/acspan containing 432 records
Current slot 432 (0 seconds)
Processing file /lat/db/iprescard containing 108 records
Current slot 108 (0 seconds)
Processing file /lat/db/blade containing 12 records
Current slot 12 (0 seconds)
Processing file /lat/db/prottable containing 100 records
Current slot 100 (0 seconds)
dbrev completed, successful restructure
Database Restructure Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/dbrev done
Copying 5.2.0/analogcard:
Copying 5.2.0/masterswcard:
Copying 5.2.0/portrescard:
Copying 5.2.0/trunkgroup:
Copying 5.2.0/ipglobalcfg:
Copying 5.2.0/analogcard.unitid:
Copying 5.2.0/masterswcard.unitid:
Copying 5.2.0/portrescard.unitid:
Copying 5.2.0/t1card.unitid:
Copying 5.2.0/t1span.unitid:
Copying 5.2.0/trunk.unitid:
Copying 5.2.0/trunkgroup.id:
Copying 5.2.0/e1card.unitid:
Copying 5.2.0/e1span.unitid:
Copying 5.2.0/accard.unitid:
Copying 5.2.0/acspan.unitid:
Copying 5.2.0/iprescard.unitid:
Copying 5.2.0/blade.bladekey:
Copying 5.2.0/blade.slot:
Copying 5.2.0/prottable.num:
cmdbrev: starting /lat/bin/initdb -y 5.2.0/tcnfg
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
cmdbrev: /lat/bin/initdb done
cmdbrev: starting /lat/bin/dbconfig -b /lat/db -f /lat/db/m3.con
cmdbrev: /lat/bin/dbconfig done
Mon Oct 26 19:01:54 PDT 2004
cmdbrev: starting 5.2.0/update -f 5.2.0 -t 5.3.0
update: starting updategen -f 5.2.0 -t 5.3.0
updategen: begun Mon Oct 26 19:01:54 PDT 2004
validating FINDME preferences
update: updategen done
update: starting updateoptions -f 5.2.0 -t 5.3.0
Updating option names ... ... Done
update: updateoptions done
update: starting upgradetcnfg -f 5.2.0 -t 5.3.0
Converting tcnfg database from 5.2.0 to 5.3
Fixing AC card records+++..+++..+++..+++..+++..+++..+++..+++..+++..!
Creating IP Global Configuration record.!
Fixing trunk
records+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++[Continues for several
lines]
Fixing group records++++++++++++++++++++++++++++++++!
update: upgradetcnfg done
cmdbrev: starting dbprealloc -b /lat/db
----------- Preallocating conf_att Mon Oct 26 19:01:58 PDT 2004
Reserving 200000 confatt records (code 10000) ...
the confatt file already has 7143 16384 byte pages that can hold 200004 record(s)
Reserving 1000 rsconfpart records (code 10001) ...
the rsconfpart file already has 8 16384 byte pages that can hold 1008 record(s)
Reserving 200000 conf records (code 10003) ...
the conf file already has 11112 16384 byte pages that can hold 200016 record(s)
Reserving 1000000 confpart records (code 10005) ...
the confpart file already has 8696 16384 byte pages that can hold 1000040 record(s)
Reserving 1000000 conftime records (code 10004) ...
the conftime file already has 5026 16384 byte pages that can hold 1000174 record(s)
Record 10002 (tmp4): has no preallocation count
Reserving 200000 partnotrec records (code 10006) ...
the partnotrec file already has 5406 16384 byte pages that can hold 200022 record(s)
Reserving 200000 confcatrec records (code 10007) ...
the confcatrec file already has 294 16384 byte pages that can hold 200508 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file confatt.confattrefid...
Adding 2 16384 byte pages to key file confatt.UpdateTime...
Adding 2 16384 byte pages to key file rsconfpart.srtuserconf...
Adding 2 16384 byte pages to key file rsconfpart.confpart...
Adding 2 16384 byte pages to key file conf.nextevent...
Adding 2 16384 byte pages to key file conf.uniquenum...
Adding 2 16384 byte pages to key file conf.sdmc...
Adding 2 16384 byte pages to key file conf.ssnd...
Adding 2 16384 byte pages to key file conf.lmcn...
Adding 2 16384 byte pages to key file conf.dspc...
Adding 2 16384 byte pages to key file conf.psdc...
Adding 2 16384 byte pages to key file conf.UpdateTime...
Adding 2 16384 byte pages to key file confpart.srtuserconf...
Adding 2 16384 byte pages to key file confpart.confpart...
Adding 2 16384 byte pages to key file confpart.UpdateTime...
Adding 2 16384 byte pages to key file conftime.confpart...
Adding 2 16384 byte pages to key file conftime.UpdateTime...
Adding 2 16384 byte pages to key file partnotrec.confpart...
Adding 2 16384 byte pages to key file partnotrec.UpdateTime...
Adding 2 16384 byte pages to key file confcatrec.cstuid...
Adding 2 16384 byte pages to key file confcatrec.uidc...
Adding 2 16384 byte pages to key file confcatrec.ConfNum...
Adding 2 16384 byte pages to key file confcatrec.UpdateTime...
----------- conf_att preallocation complete Mon Oct 26 19:01:59 PDT 2004
----------- Preallocating config Mon Oct 26 19:01:59 PDT 2004
Reserving 1 billinginfo records (code 10000) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 1 companyinfo records (code 10001) ...
the companyinfo file already has 1 record(s)
Reserving 1 filestats records (code 10002) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 1 hwconfig records (code 10003) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 1 hwstats records (code 10004) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 26 option records (code 10005) ...
Adding 1 1024 byte page(s) to get 2 record(s) ...
Reserving 64 outdialtrans records (code 10006) ...
the outdialtrans file already has 1 16384 byte pages that can hold 122 record(s)
Reserving 1 netmgtinfo records (code 10013) ...
the netmgtinfo file already has 1 record(s)
Reserving 10 netmgtcomm records (code 10014) ...
the netmgtcomm file already has 1 16384 byte pages that can hold 105 record(s)
Reserving 32 unit records (code 10015) ...
the unit file already has 128 record(s)
Reserving 8 site records (code 10017) ...
the site file already has 8 record(s)
Reserving 1 promptstats records (code 10007) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 10 scsi records (code 10008) ...
the scsi file already has 128 record(s)
Reserving 1 swconfig records (code 10009) ...
the swconfig file already has 1 record(s)
Reserving 1 swstats records (code 10010) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 1 systemconfig records (code 10011) ...
the systemconfig file already has 1 record(s)
Reserving 1 timezone records (code 10012) ...
the timezone file already has 319 record(s)
Reserving 10000 mtgcategory records (code 10016) ...
Adding 105 16384 byte page(s) to get 9905 record(s) ...
Reserving 1000 remoteserver records (code 10018) ...
Adding 24 16384 byte page(s) to get 1000 record(s) ...
Record 10019 (didcnfgconfig): has no preallocation count
Record 10020 (schedparamsconfig): has no preallocation count
Pre-allocating each key file...
Adding 3 16384 byte pages to key file filestats.recnum...
Adding 3 16384 byte pages to key file netmgtcomm.name...
Adding 3 16384 byte pages to key file outdialtrans.recnum...
Adding 3 1024 byte pages to key file option.name...
Adding 3 16384 byte pages to key file timezone.id...
Adding 3 16384 byte pages to key file timezone.timezonekey...
Adding 3 16384 byte pages to key file unit.unitnum...
Adding 3 16384 byte pages to key file site.sitenum...
Adding 3 16384 byte pages to key file scsi.unitid...
Adding 17 16384 byte pages to key file mtgcategory.uniqueid...
Adding 37 16384 byte pages to key file mtgcategory.name...
Adding 47 16384 byte pages to key file mtgcategory.mtgcatkey...
Adding 3 16384 byte pages to key file remoteserver.uniqueid...
Adding 3 16384 byte pages to key file remoteserver.name...
Adding 3 16384 byte pages to key file remoteserver.vuiid...
Adding 3 16384 byte pages to key file remoteserver.ether...
----------- config preallocation complete Mon Oct 26 19:02:00 PDT 2004
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
----------- Preallocating db Mon Oct 26 19:02:00 PDT 2004
Reserving 100 db records (code 10000) ...
the db file already has 1 16384 byte pages that can hold 143 record(s)
Reserving 200 dbclass records (code 10001) ...
Adding 2 16384 byte page(s) to get 127 record(s) ...
Reserving 200 dbmember records (code 10002) ...
Adding 1 16384 byte page(s) to get 200 record(s) ...
Pre-allocating each key file...
Adding 3 16384 byte pages to key file db.name...
Adding 3 16384 byte pages to key file dbclass.dbnamerecid...
Adding 5 16384 byte pages to key file dbclass.csdbnameskey...
Adding 3 16384 byte pages to key file dbclass.dbname...
Adding 3 16384 byte pages to key file dbclass.classname...
Adding 3 16384 byte pages to key file dbmember.fieldid...
----------- db preallocation complete Mon Oct 26 19:02:00 PDT 2004
----------- Preallocating deletedrec Mon Oct 26 19:02:00 PDT 2004
Reserving 1000000 deletedrec records (code 10000) ...
the deletedrec file already has 1000000 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file deletedrec.Sequence...
----------- deletedrec preallocation complete Mon Oct 26 19:02:01 PDT 2004
----------- Preallocating flexmenu Mon Oct 26 19:02:01 PDT 2004
Record 10000 (FMAppRec): has no preallocation count
Record 10001 (FMStateTable): has no preallocation count
Record 10002 (CustAppPrompt): has no preallocation count
Record 10003 (FMPlayPrompt): has no preallocation count
Record 10004 (FMGotoApp): has no preallocation count
Record 10005 (FMOptionMenu): has no preallocation count
Record 10006 (FMHangUp): has no preallocation count
Record 10007 (FMFindMtg): has no preallocation count
Record 10008 (FMReviewMtgMat): has no preallocation count
Record 10009 (FMGetProfile): has no preallocation count
Pre-allocating each key file...
----------- flexmenu preallocation complete Mon Oct 26 19:02:02 PDT 2004
----------- Preallocating gen Mon Oct 26 19:02:02 PDT 2004
Reserving 250000 user records (code 10002) ...
the user file already has 19231 16384 byte pages that can hold 250003 record(s)
Reserving 100 group records (code 10000) ...
the group file already has 3 16384 byte pages that can hold 117 record(s)
Record 10003 (gentmp1): has no preallocation count
Record 10005 (gentmp2): has no preallocation count
Record 10004 (gentmp3): has no preallocation count
Reserving 6 flexfield records (code 10001) ...
the flexfield file already has 14 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file user.last...
Adding 2 16384 byte pages to key file user.name...
Adding 2 16384 byte pages to key file user.uniqueid...
Adding 2 16384 byte pages to key file user.username...
Adding 2 16384 byte pages to key file user.cuid...
Adding 2 16384 byte pages to key file user.cnlf...
Adding 2 16384 byte pages to key file user.lfn...
Adding 2 16384 byte pages to key file user.in...
Adding 2 16384 byte pages to key file user.vuname...
Adding 2 16384 byte pages to key file user.glfn...
Adding 2 16384 byte pages to key file user.UpdateTime...
----------- gen preallocation complete Mon Oct 26 19:02:02 PDT 2004
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
----------- Preallocating pegs Mon Oct 26 19:02:02 PDT 2004
Reserving 1 pegs records (code 10000) ...
the pegs file already has 1536 record(s)
Pre-allocating each key file...
----------- pegs preallocation complete Mon Oct 26 19:02:02 PDT 2004
----------- Preallocating podata Mon Oct 26 19:02:02 PDT 2004
Reserving 1 pomailbox records (code 10000) ...
the pomailbox file already has 32 record(s)
Reserving 20000 pomsgdata records (code 10001) ...
Pre-allocating each key file...
Adding 2 16384 byte pages to key file pomsgdata.compundkey...
----------- podata preallocation complete Mon Oct 26 19:02:02 PDT 2004
----------- Preallocating res Mon Oct 26 19:02:02 PDT 2004
Reserving 1 crres records (code 10004) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 1 portres records (code 10005) ...
Adding 1 16384 byte page(s) to get 1 record(s) ...
Reserving 200000 didres records (code 10001) ...
Adding 513 16384 byte page(s) to get 200000 record(s) ...
Record 10000 (didconfigres): has no preallocation count
Record 10003 (schedparamsres): has no preallocation count
Reserving 13 crresfstaccess records (code 10006) ...
the crresfstaccess file already has 13 record(s)
Reserving 13 portresfstaccess records (code 10007) ...
the portresfstaccess file already has 13 record(s)
Reserving 13 vsresfstaccess records (code 10008) ...
the vsresfstaccess file already has 15 record(s)
Reserving 200000 vsres records (code 10002) ...
Adding 465 16384 byte page(s) to get 200000 record(s) ...
Pre-allocating each key file...
Adding 635 16384 byte pages to key file didres.strtdid...
Adding 343 16384 byte pages to key file didres.UpdateTime...
Adding 3 16384 byte pages to key file crres.resourceid...
Adding 3 16384 byte pages to key file portres.resourceid...
Adding 343 16384 byte pages to key file vsres.resourceid...
Adding 343 16384 byte pages to key file vsres.UpdateTime...
----------- res preallocation complete Mon Oct 26 19:02:07 PDT 2004
Database Initialization Utility
Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm
Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved.
----------- Preallocating status Mon Oct 26 19:02:07 PDT 2004
Reserving 200 alarmentry records (code 10000) ...
the alarmentry file already has 200 record(s)
Reserving 16384 exlogentry records (code 10001) ...
the exlogentry file already has 16384 record(s)
Reserving 1 hwstatus records (code 10002) ...
the hwstatus file already has 1 16384 byte pages that can hold 2047 record(s)
Reserving 1 swstatus records (code 10003) ...
the swstatus file already has 1 record(s)
Reserving 1500 exlogformat records (code 10004) ...
the exlogformat file already has 3374 record(s)
Reserving 20 apps records (code 10005) ...
the apps file already has 21 record(s)
Reserving 10000 outdial records (code 10006) ...
the outdial file already has 10000 record(s)
Reserving 10000 notification records (code 10007) ...
the notification file already has 10000 record(s)
Record 10008 (schedfail): has no preallocation count
Record 10009 (gwstatus): has no preallocation count
Pre-allocating each key file...
----------- status preallocation complete Mon Oct 26 19:02:08 PDT 2004
----------- Preallocating tcnfg Mon Oct 26 19:02:08 PDT 2004
Reserving 100 analogcard records (code 10000) ...
the analogcard file already has 1 16384 byte pages that can hold 431 record(s)
Reserving 1 masterswcard records (code 10001) ...
the masterswcard file already has 108 record(s)
Reserving 100 portrescard records (code 10002) ...
the portrescard file already has 108 record(s)
Reserving 100 t1card records (code 10003) ...
the t1card file already has 108 record(s)
Reserving 10 t1span records (code 10004) ...
the t1span file already has 432 record(s)
Reserving 1000 trunk records (code 10005) ...
the trunk file already has 10800 record(s)
Reserving 100 trunkgroup records (code 10006) ...
the trunkgroup file already has 1 16384 byte pages that can hold 110 record(s)
Reserving 100 e1card records (code 10007) ...
the e1card file already has 1 16384 byte pages that can hold 163 record(s)
Reserving 10 e1span records (code 10008) ...
the e1span file already has 36 record(s)
Record 10009 (accard): has no preallocation count
Record 10010 (acspan): has no preallocation count
Record 10012 (iprescard): has no preallocation count
Record 10013 (blade): has no preallocation count
Record 10014 (prottable): has no preallocation count
Record 10011 (ipglobalcfg): has no preallocation count
Pre-allocating each key file...
Adding 3 16384 byte pages to key file analogcard.unitid...
Adding 3 16384 byte pages to key file masterswcard.unitid...
Adding 3 16384 byte pages to key file portrescard.unitid...
Adding 3 16384 byte pages to key file t1card.unitid...
Adding 3 16384 byte pages to key file t1span.unitid...
Adding 3 16384 byte pages to key file trunkgroup.id...
Adding 3 16384 byte pages to key file e1card.unitid...
Adding 3 16384 byte pages to key file e1span.unitid...
----------- tcnfg preallocation complete Mon Oct 26 19:02:08 PDT 2004
----------- Preallocating userlist Mon Oct 26 19:02:08 PDT 2004
Reserving 100000 userlist records (code 10000) ...
the userlist file already has 2041 16384 byte pages that can hold 100009 record(s)
Reserving 500000 userlistmem records (code 10001) ...
the userlistmem file already has 611 16384 byte pages that can hold 500409 record(s)
Pre-allocating each key file...
Adding 2 16384 byte pages to key file userlist.uniqueid...
Adding 2 16384 byte pages to key file userlist.vuiid...
Adding 2 16384 byte pages to key file userlist.name...
Adding 2 16384 byte pages to key file userlist.unta...
Adding 2 16384 byte pages to key file userlist.UpdateTime...
Adding 2 16384 byte pages to key file userlist.oulid...
Adding 2 16384 byte pages to key file userlistmem.uluid...
Adding 2 16384 byte pages to key file userlistmem.UpdateTime...
----------- userlist preallocation complete Mon Oct 26 19:02:08 PDT 2004
cmdbrev: starting delrecinit
There are supposed to be 1,000,000 records in the deleted record database
Counting the number of records in the database...
cmdbrev: ending Mon Oct 26 19:02:50 PDT 2004
Mon Oct 26 19:02:50 PDT 2004 Network setup:
Unit class = SINGLE/LOCAL
Updating error log format strings: Using database path: /lat/db/status
48 new entries and 3375 replacements
Prompt Upgrade>> Opening file </lat/fs.1/prompt_db_vfs_map_dir0> ....
Number Of Language(s) in the prompt map file: 1
Prompt Upgrade>> EOF (0) reached in /lat/fs.1/prompt_db_vfs_map_dir0 file (promptNum
1551): 0
... Done with English (US)
Starting Update Company Info
The languages installed are:
Language 1 dir0 English (US)
FINISHED: Prompt Database Upgrade is complete!
Statistics: 0 new entries and 319 replacements
Updating time zone names: Using database path: /lat/db/config
Updating option names ... ... Done
Setting prompt file configuration
The file system directories are already updated
The file system directories are already updated
The file system directories are already updated
Adjusting prompt file sizes
Initializing the file system...
Getting the disk configuration status...
Checking file system internal consistency... (may take a while) ...
Number of records in the prompt files has been updated, ret = a0084
Mon Oct 26 19:02:57 PDT 2004 NOTE: Disk backups disabled; run 'save' to re-enable.
Mon Oct 26 19:02:57 PDT 2004 Software update is complete.
Update is complete. Restarting...
LynxOS 386/486/Pentium PC-AT Version 3.1.0
Copyright 1987-1998 Lynx Real-Time Systems Inc.
LynxOS (x86) created Tue Sep 30 15:05:41 PDT 2003
MeetingPlace by Cisco Systems
Mon Oct 26 19:03:53 PDT 2004
(all sizes and block numbers in decimal)
(file system is byte-swapped)
(file system creation time is Mon Oct 26 18:50:30 2004)
(file system contains 31999 blocks and 7936 inodes)
checking for orphaned files
making bit map free block list
14586 free blocks 5963 free inodes
Unit class is standalone conference server (SINGLE).
Bus architecture is CompactPCI (M3).
Ethernet device is "pro0".
Initializing the modem on COM2.../lat/bin/initmodem ...
/lat/bin/initmodem: type is `MultiTech MT5634Z'
/lat/bin/initmodem: modem initialized
Installing Latitude drivers...
devinstall: acti.dat: Device doesn't exist
Checking for out of date database files
Ready to load the MeetingPlace application software modules.
Hit ^C now to interrupt system activation...54321...activating
Loading the System Integrity Manager...OK
WARNING: Mount table does not match saved configuration
Automated disk backup disabled; run "save" to reenable
Loading the Command Shell...OK
Loading the Network Management Server...OK
Loading the Database Server...OK
Loading the Post Office Server...OK
Loading the Call Processing Module...OK
Loading the Conference Scheduler...OK
Loading the Workstation Server...OK
Loading the Voice User Interface ...OK
Loading the Gateway SIM Manager...OK
Release 5.3, Oct 26, 2004
user name: The MeetingPlace software is UP
Viewing the Onsite Installation or Upgrade for a Sample Session with a Disk Backup
Please insert the update diskette in the drive.
Press <ENTER> to continue or <CONTROL-C> to abort.
ln: symlink(ide.2, cd): File already exists
ln: symlink(ride.2, rcd): File already exists
Please insert the update CD in the drive, then
wait for the drive to be quiet before continuing.
Press <ENTER> to continue or <CONTROL-C> to abort.
CD mounted OK; checking for update sets...
There is just one update set on the CD.
You wish to install: MeetingPlace 5.3
Is this correct? (y or n) y
---------------------------------------------------------------
- MeetingPlace software release 5.3
- Archive created: Fri Oct 29 13:51:39 PDT 2004
---------------------------------------------------------------
Press <ENTER> to continue or <CONTROL-C> to abort.
Sat Oct 30 20:22:45 PDT 2004 Starting ./UPDATE.phase1
Sat Oct 30 20:22:46 PDT 2004 Verifying the tape image checksum
Sat Oct 30 20:23:41 PDT 2004 Killing cron
Sat Oct 30 20:23:42 PDT 2004 Failed to unmount /mnt
Sat Oct 30 20:23:42 PDT 2004 Please 'restart disable' and try again
umount: /mnt: Device busy
bigfoot:tech$ restart enable