Support

Table Of Contents

show authentication

show authorization

show boot

show bridge

show cam

show cam agingtime

show cam mlsrp

show cdp

show cgmp leave

show cgmp statistics

show channel

2

show authentication

Use the show authentication command to display authentication information.

show authentication

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Examples

This example shows how to display authentication information:

Console> show authentication

                       Console Session   Telnet Session   Http Session

Login Authentication:

---------------------  ----------------  ---------------  -----------

tacacs                 disabled          disabled         disabled

radius                 disabled          disabled         enabled(*)

kerberos               disabled          disabled         disabled

local                  enabled(*)        enabled(*)       enabled

Enable Authentication:

---------------------- ----------------  ---------------

tacacs                 disabled          disabled

radius                 disabled          disabled

kerberos               disabled          disabled       

local                  enabled(*)        enabled(*)

(*) primary

Console> 

Related Commands

set authentication enable
set authentication login

show authorization

Use the show authorization command to display authorization setup and configuration information on the switch.

show authorization

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Examples

This example shows how to display authorization information:

Console> (enable) show authorization 

Telnet:

-------

            Primary   Fallback

            -------   --------

exec:       tacacs+   If-authen

enable:     -         -

commands:   

 config:    tacacs+   If-authen

 all:       -         -

Console:

--------

            Primary   Fallback

            -------   --------

exec:       tacacs+   If-authen

enable:     -         -

commands:   

 config:    -         -

 all:       -         -

Console> (enable)

Related Commands

set authorization commands
set authorization enable
set authorization exec

show boot

---

Note This command applies only to the Supervisor Engine III or the Catalyst 4000 family and 2948G switch supervisor engine modules. If you attempt to run this command on a Supervisor Engine I or II, you will receive an error message.

---

Use the show boot command to display the contents of the BOOT environment variables and the configuration register setting.

show boot [mod_num]

Syntax Description

mod_num

(Optional) Module number of the supervisor engine containing the Flash device.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Usage Guidelines

This command can only be used with a Supervisor Engine III or Catalyst 4000 family and 2948G switch supervisor engine module.

Examples

This example shows how to use the show boot command:

Console> show boot

BOOT variable = bootflash:cat5000-sup3.5-1-0-59.bin,1;bootflash:cat5000-sup3.4-;

CONFIG_FILE variable = slot0:cfgfile1;slot0:cfgfile2

Configuration register is 0x10f

ignore-config: disabled

auto-config: recurring

console baud: 9600

boot: image specified by the boot system commands

Console>

Related Commands

show boot

show bridge

Use the show bridge command to display bridge information.

show bridge

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Usage Guidelines

This command is supported by the Catalyst 5000 family switches.

Examples

This example shows how to display bridge information:

Console> show bridge

APaRT Enabled

FDDICHECK Enabled

IP fragmentation Enabled

Default IPX translations:

    FDDI SNAP  to Ethernet     8023raw

    FDDI 802.2 to Ethernet     8023raw

    Ethernet 802.3 Raw to FDDI snap

Console> 

Table 2-10 describes the fields in the show bridge output.

Table 2-10 show bridge Command Output Fields

Field	Description
APaRT Enabled	Status of whether APaRT is enabled or disabled.
FDDICHECK Enabled	Status of whether FDDICHECK is enabled or disabled.
IP fragmentation Enabled	Status of whether IP fragmentation is enabled or disabled.
IPX translations	Default method for translating IPX packets across various media.

Related Commands

set bridge ipx 8022toether
set bridge ipx 8023rawtofddi
set bridge ipx snaptoether
set ip dns domain

show cam

Use the show cam command to display the CAM table.

show cam count {dynamic | static | permanent | system} [vlan]

show cam {dynamic | static | permanent} mod_num/port_num

show cam mac_addr [vlan]

Syntax Description

count	Keyword that specifies to display only the number of CAM entries.
dynamic	Keyword that specifies to display dynamic CAM entries.
static	Keyword that specifies to display static CAM entries.
permanent	Keyword that specifies to display permanent CAM entries.
system	Keyword that specifies to display system CAM entries.
vlan	(Optional) Number of the VLAN. If a VLAN is not specified, all VLANs are displayed.
mod_num	Number of the module.
port_num	Number of the port.
mac_addr	MAC address.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Usage Guidelines

If you display the output associated with the MAC address of an ATM dual PHY OC-12 module, additional information is displayed, including the VCD, VPI, VCI, and VC type.

If you enter the show cam command on the Catalyst 5000 family and 2926G series switches, the EARL CAM table entries are displayed.

If you enter the show cam command on the Catalyst 4000 family, 2948G, and 2980G switches, the ASE CAM table entries are displayed.

The Catalyst 2948G and 2980G switches are fixed configuration switches. Ports are located on module 2 for the 2948G and on modules 2 and 3 for the 2980G; for this reason, if you enter 1/N for the module/port number, an error message is displayed.

Examples

This example shows how to display dynamic CAM entries for all VLANs:

Console> show cam dynamic

* = Static Entry. + = Permanent Entry. # = System Entry. R = Router Entry.

VLAN  Dest MAC/Route Des    Destination Ports or VCs / [Protocol Type]

----  ------------------    ----------------------------------------------------

1     00-60-5c-86-5b-81     4/1 [ALL]

1     00-60-2f-35-48-17     4/1 [ALL]

1     00-80-24-f3-47-20     1/2 [ALL]

1     00-60-09-78-96-fb     4/1 [ALL]

1     00-80-24-1d-d9-ed     1/2 [ALL]

1     00-80-24-1d-da-01     1/2 [ALL]

1     08-00-20-7a-63-01     4/1 [ALL]

Total Matching CAM Entries Displayed = 7

Console> 

This example shows the output associated with the MAC address of an ATM dual PHY OC-12 module, which includes the dynamic CAM entries for all VLANs:

Console> show cam dynamic

VLAN  Dest MAC/Route Des  Destination Ports or VCs

----  ------------------  ----------------------------------------------------

12    00-14-14-14-14-1c   6/1

12    00-14-14-14-14-1d   6/1

12    00-14-14-14-14-1a   6/1

12    00-14-14-14-14-1b   6/1

12    00-14-14-14-14-18   6/1

12    00-14-14-14-14-19   6/1

12    00-14-14-14-14-16   6/1

12    00-14-14-14-14-17   6/1

12    00-14-14-14-14-14   6/1

12    00-14-14-14-14-15   6/1

6     00-14-14-14-14-16   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-17   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-14   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-15   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-1a   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-1b   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-18   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-19   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-1c   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

6     00-14-14-14-14-1d   4/1 VCD:98  VPI:0 VCI:127  Type: LANE Data Direct

3     00-14-14-14-14-14   4/1 VCD:101 VPI:0 VCI:130  Type: LANE Data Direct

3     00-14-14-14-14-15   4/1 VCD:101 VPI:0 VCI:130  Type: LANE Data Direct

Do you wish to continue y/n [n]? q

Total Matching CAM Entries Displayed = 21

Console> 

Table 2-11 describes the fields in the ATM dual PHY OC-12 module show cam dynamic output.

Table 2-11 show cam dynamic Command Output Fields

Field	Description
VCD	VCD of the VC.
VPI	VPI of the VC.
VCI	VCI of the VC.
Type	Type of virtual circuit (LANE Data Direct, LANE bus, or AAL5SNAP PVC).

This example shows routers listed as the CAM entries. If the MAC address belongs to a router, it is shown by appending an "R" to the MAC address. If a VLAN is specified, then only those CAM entries matching the VLAN number are displayed.

Console> show cam 00-00-81-01-23-45

* = Static Entry. + = Permanent Entry. # = System Entry. R = Router Entry

Router Watergate with IP address 172.25.55.1 has CAM entries:

VLAN  Dest MAC/Route Des    Destination Ports or VCs

----  ------------------    ----------------------------------------------------

1     00-00-81-01-23-45R    2/9 [IP]

2     00-00-81-01-23-45R    2/10 [IP]

Total Matching CAM Entries = 2

Console>

Related Commands

clear cam
set cam
show config
show cam agingtime

show cam agingtime

Use the show cam agingtime command to display CAM aging time information for all configured VLANs.

show cam agingtime

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Examples

This example shows how to display CAM aging time information:

Console> show cam agingtime

VLAN   1 aging time = 300 sec

VLAN   3 aging time = 300 sec

VLAN   5 aging time = 300 sec

VLAN   9 aging time = 300 sec

VLAN 100 aging time = 300 sec

VLAN 200 aging time = 300 sec

VLAN 201 aging time = 300 sec

VLAN 202 aging time = 300 sec

VLAN 203 aging time = 300 sec

Console> 

Related Commands

clear cam
set cam
show cam

show cam mlsrp

Use the show cam mlsrp command to display the specified router entries in the MLS forwarding table. If you can specify a VLAN number, only the router MAC addresses corresponding to the VLAN are displayed.

show cam mlsrp {ip_addr} [vlan]

Syntax Description

ip_addr	IP address of the router or name of the router if DNS is enabled.
vlan	(Optional) Number of the VLAN. If you do not specify a VLAN, all VLANs are displayed.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Usage Guidelines

This command is supported by the Catalyst 5000 family switches and the Catalyst 2926G series switches.

Examples

This example shows how to display all CAM entries for the specified router:

Console>(enable) show cam mlsrp 172.20.22.1

VLAN Destination MAC      Destination Ports or VCs  Xtag Status

---- -------------------  -------------------------------------

1     00-00-81-01-23-45R  2/9                          5  H 	

2     00-00-81-01-23-45R  2/10                         5  H 	

Total Matching CAM Entries Displayed = 2

Console>(enable)

Related Commands

show cam

show cdp

Use the show cdp command to display CDP information.

show cdp

show cdp neighbors [mod_num] [vlan | duplex | capabilities | detail]

show cdp neighbors [mod_num/port_num] [vlan | duplex | capabilities | detail]

show cdp port [mod_num]

show cdp port [mod_num/port_num]

Syntax Description

neighbors	Keyword that specifies to show CDP information for Cisco products connected to the switch.
mod_num	(Optional) Number of the module for which CDP information is displayed. If no module number is specified, CDP information for the entire switch is displayed.
vlan	(Optional) Keyword that specifies to show the native VLAN number for the neighboring Cisco products.
duplex	(Optional) Keyword that specifies to show duplex type of the neighboring Cisco products.
capabilities	(Optional) Keyword that specifies to show the capability codes for the neighboring Cisco products; valid values are R, T, B, S, H, I, r (R=Router, T=Trans Bridge, B=Source Route Bridge, S=Switch, H=Host, I=IGMP, and r=Repeater).
detail	(Optional) Keyword that specifies to show detailed information about neighboring Cisco products.
port_num	(Optional) Number of the port for which CDP information is displayed.
port	Keyword that specifies to show CDP port settings.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Examples

This example shows how to display CDP information for the system:

Console> show cdp

CDP               :enabled

Message Interval  :60

Hold Time         :180

Version           :V2

Console>

This example shows how to display detailed CDP neighbor information. The display varies depending on your network configuration at the time you run the command.

Console> show cdp neighbors 4/4 detail

Port (Our Port):4/4

Device-ID:69046406

Device Addresses:

  IP Address:172.20.25.161

Holdtime:150 sec

Capabilities:TRANSPARENT_BRIDGE SWITCH

Version:

  WS-C5509 Software, Version McpSW: 5.3(0.29)BOU NmpSW: 5.3(0.29)BOU

  Copyright (c) 1995-1999 by Cisco Systems

Port-ID (Port on Device):4/8

Platform:WS-C6009

VTP Management Domain:unknown

Native VLAN:1

Duplex:half

Console> 

This example shows how to display CDP information about neighboring systems:

Console> show cdp neighbors

* - indicates vlan mismatch.

# - indicates duplex mismatch.

Port     Device-ID                       Port-ID                   Platform

-------- ------------------------------- ------------------------- ------------

3/5      002267619                       3/6 *                     WS-C5000  

3/6      002267619                       3/5                       WS-C5000

4/1      002267619                       4/2                       WS-C5000

4/2      002267619                       4/1 #                     WS-C5000

4/20     069000057                       8/5                       WS-C5500

5/1      005763872                       2/1                       WS-C5000

5/1      066506245                       2/1                       WS-C5505

5/1      066508595                       5/12 *#                   WS-C5505

5/1      066508596                       5/1                       WS-C5505

Console> 

This example shows how to display VLAN information about neighboring systems:

Console> show cdp vlan

* - indicates vlan mismatch.

# - indicates duplex mismatch.

Port     Device-ID                       Port-ID                   NativeVLAN 

-------- ------------------------------- ------------------------- ----------

3/5      002267619                       3/6 *                     1

3/6      002267619                       3/5                       1

4/1      002267619                       4/2                       1

4/2      002267619                       4/1 #                     1

4/20     069000057                       8/5                       -

5/1      066508595                       5/12 *#                   1

5/1      066508596                       5/1                       1

Console> 

This example shows how to display duplex information about neighboring systems:

Console> show cdp neighbors duplex 

* - indicates vlan mismatch.

# - indicates duplex mismatch.

Port     Device-ID                       Port-ID                   Duplex

-------- ------------------------------- ------------------------- ------

3/5      002267619                       3/6 *                     half

3/6      002267619                       3/5                       half

4/1      002267619                       4/2                       full

4/2      002267619                       4/1 #                     full

4/20     069000057                       8/5                       -

5/1      005763872                       2/1                       -

5/1      066506245                       2/1                       -

5/1      066508595                       5/12 *#                   half

5/1      066508596                       5/1                       half

Console> 

This example shows how to display capability information about neighboring systems:

Console> show cdp neighbors capabilities

* - indicates vlan mismatch.

# - indicates duplex mismatch.

Port     Device-ID                       Port-ID                   Capabilities

-------- ------------------------------- ------------------------- ------------

3/5      002267619                       3/6 *                     T S

3/6      002267619                       3/5                       T S

4/1      002267619                       4/2                       T S

4/2      002267619                       4/1 #                     T S

4/20     069000057                       8/5                       T B S

5/1      005763872                       2/1                       T B S

5/1      066506245                       2/1                       T B S

5/1      066508595                       5/12 *#                   T B S

5/1      066508596                       5/1                       T B S

Console> 

This example shows how to display CDP information for all ports:

Console> show cdp port

CDP               :enabled

Message Interval  :60

Hold Time         :180

Version           :V2

Port      CDP Status 

--------  ---------- 

 2/1      enabled     

 2/2      enabled     

 5/1      enabled     

 5/2      enabled     

 5/3      enabled     

 5/4      enabled     

 5/5      enabled     

 5/6      enabled     

 5/7      enabled     

 5/8      enabled     

Console> 

Related Commands

set cdp

show cgmp leave

Use the show cgmp leave command to display the status of the CGMP leave feature.

show cgmp leave

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Examples

This example shows how to display the status of the CGMP leave feature:

Console> show cgmp leave

CGMP:       enabled

CGMP leave: enabled

Console> 

Related Commands

set cgmp leave

show cgmp statistics

Use the show cgmp statistics command to display CGMP statistics.

show cgmp statistics [vlan_id]

Syntax Description

vlan_id

(Optional) VLAN number for which to display CGMP statistics.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Examples

This example shows how to display CGMP statistics for VLAN 1:

Console> show cgmp statistics 1 
CGMP enabled

CGMP statistics for vlan 1:

valid rx pkts received           211915

invalid rx pkts received         0

valid cgmp joins received        211729

valid cgmp leaves received       186

valid igmp leaves received       0

valid igmp queries received      3122

igmp gs queries transmitted      0

igmp leaves transmitted          0

failures to add GDA to EARL      0

topology notifications received  80

number of CGMP packets dropped   2032227

Console> 

Table 2-12 describes the fields in the show cgmp statistics output.

Table 2-12 show cgmp statistics Command Output Fields 

Field	Description
Valid rx pkts received	Number of valid CGMP packets received.
Invalid rx pkts received	Number of invalid CGMP packets received.
valid cgmp joins received	Number of CGMP group-specific queries received.
valid cgmp leaves received	Number of CGMP leaves received.
valid igmp leaves received	Number of IGMP leaves received.
valid igmp queries received	Number of IGMP reports received.
igmp gs queries transmitted	Number of IGMP group specific-equivalent queries transmitted by the switch.
igmp leaves transmitted	Number of IGMP leaves transmitted by the switch.
failures to add GDA to EARL	Number of times the switch failed to add a multicast entry (GDA) to the EARL table.
topology notifications received	Number of topology change notifications received by the switch.
number of CGMP packets dropped	Number of IGMP packets dropped by the switch.

Related Commands

clear cgmp statistics
set cgmp

show channel

Use the show channel command to display EtherChannel configuration and statistics information for a channel based on EtherChannel ID.

show channel [channel_id] [statistics | mac | info [spantree | trunk | protocol | gmrp | gvrp |
qos]]

Syntax Description

channel_id	(Optional) EtherChannel ID of the channel.
statistics	(Optional) Keyword that specifies to display EtherChannel PAgP statistics.
mac	(Optional) Keyword that specifies to display EtherChannel traffic statistics.
info	(Optional) Keyword that specifies to display EtherChannel configuration information.
spantree	(Optional) Keyword that specifies to display only spanning-tree-related configuration information.
trunk	(Optional) Keyword that specifies to display only VLAN-trunk-related configuration information.
protocol	(Optional) Keyword that specifies to display only protocol-filtering-related configuration information.
gmrp	(Optional) Keyword that specifies to display only GMRP-related configuration information.
gvrp	(Optional) Keyword that specifies to display only  GVRP-related configuration information.
qos	(Optional) Keyword that specifies to display only QoS-related configuration information.

Defaults

This command has no default setting.

Command Types

Switch command.

Command Modes

Normal.

Usage Guidelines

If channel_id is not specified, EtherChannel information is shown for all channels.

If you use the info keyword without qualifying it with one of the feature-specific keywords, all configuration information is displayed.

No information is displayed if the EtherChannel specified is not in use.

Examples

This example shows how to display PAgP statistics for a specific EtherChannel:

Console> show channel 835 statistics

Port  Channel PAgP Pkts   PAgP Pkts PAgP Pkts PAgP Pkts PAgP Pkts PAgP Pkts

      id      Transmitted Received  InFlush   RetnFlush OutFlush  InError

----- ------- ----------- --------- --------- --------- --------- ---------

 7/5      835         194        81         0         0         0         0

 7/6      835         204        85         0         0         0         0

Console> 

This example shows how to display traffic statistics for a specific EtherChannel:

Console> show channel 835 mac

Channel  Rcv-Unicast          Rcv-Multicast        Rcv-Broadcast

-------- -------------------- -------------------- --------------------

835                         0               114650                    0

Channel  Xmit-Unicast         Xmit-Multicast       Xmit-Broadcast

-------- -------------------- -------------------- --------------------

835                         0               177145                    0

Channel  Rcv-Octet            Xmit-Octet

-------- -------------------- --------------------

835                  10852890             14371660

Channel  Dely-Exced MTU-Exced  In-Discard Lrn-Discrd In-Lost    Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

835               0          0          0          0          0          0

Console> 

This example shows how to display EtherChannel information for all channels:

Console> show channel

Channel Id   Ports

-----------  -----------------------------------------------

768          2/1-2                                          

769          4/3-4                                          

770          4/7-8                                          

Console> 

This example shows how to display configuration information for a specific EtherChannel:

Console> show channel 835 info

Chan Port  Status     Channel              Admin Speed Duplex Vlan

id                    mode                 group

---- ----- ---------- -------------------- ----- ----- ------ ----

 835  7/5  connected  on                      58 a-100 a-full    1

 835  7/6  connected  on                      58 a-100 a-full    1

Chan Port  if-   Oper-group Neighbor   Chan  Oper-Distribution PortSecurity/

id         Index            Oper-group cost  Method            Dynamic Port

---- ----- ----- ---------- ---------- ----- ----------------- -------------

 835  7/5  379            1                0 mac both                       

 835  7/6  379            1                0 mac both                       

Chan Port  Device-ID                       Port-ID                   Platform

id

---- ----- ------------------------------- ------------------------- ----------

 835  7/5  069003103(5500)                 3/5                       WS-C5500

 835  7/6  069003103(5500)                 3/6                       WS-C5500

Chan Port  Trunk-status Trunk-type    Trunk-vlans

id

----- ----- ------------ ------------- -----------------------------------------

 835  7/5  not-trunking negotiate     1-1005

 835  7/6  not-trunking negotiate     1-1005

Chan Port  Portvlancost-vlans

id

---- ----- --------------------------------------------------------------------

 835  7/5  

 835  7/6  

Chan Port  Port     Portfast Port    Port

id         priority          vlanpri vlanpri-vlans

---- ----- -------- -------- ------- ------------------------------------------

 835  7/5        32 disabled       0 

 835  7/6        32 disabled       0 

Chan Port  IP       IPX      Group

id

---- ----- -------- -------- --------

 835  7/5  on       auto-on  auto-on 

 835  7/6  on       auto-on  auto-on 

Chan Port  GMRP     GMRP         GMRP

id         status   registration forwardAll

---- ----- -------- ------------ ----------

 835  7/5  enabled  normal       disabled  

 835  7/6  enabled  normal       disabled  

Chan Port  GVRP     GVRP          GVRP

id         status   registeration applicant

---- ----- -------- ------------- ---------

 835  7/5  disabled normal        normal   

 835  7/6  disabled normal        normal   

Chan Port  Qos-Tx Qos-Rx Qos-Trust    Qos-DefCos

id

---- ----- ------ ------ ------------ ----------

 835  7/5  1q4t   -      untrusted             0

 835  7/6  1q4t   -      untrusted             0

Console> 

Table 2-13 describes the fields in the show channel statistics output.

Table 2-13 show channel statistics Command Output Fields 

Field	Description
Port	Port number.
Channel id	EtherChannel ID.
PAgP Pkts Transmitted	Number of PAgP packets transmitted on the port.
PAgP Pkts Received	Number of PAgP packets received on the port.
PAgP Pkts InFlush	Number of PAgP flush packets received.
PAgP Pkts RetnFlush	Number of PAgP flush packets returned.
PAgP Pkts OutFlush	Number of PAgP flush packets transmitted.
PAgP Pkts InError	Number of PAgP error packets received.

Table 2-14 describes the fields in the show channel mac output.

Table 2-14 show channel mac Command Output Fields

Field	Description
Channel	EtherChannel ID.
Rcv-Unicast	Number of unicast frames received on the EtherChannel.
Rcv-Multicast	Number of multicast frames received on the EtherChannel.
Rcv-Broadcast	Number of broadcast frames received on the EtherChannel.
Xmit-Unicast	Number of unicast frames transmitted on the EtherChannel.
Xmit-Multicast	Number of multicast frames transmitted on the EtherChannel.
Xmit-Broadcast	Number of broadcast frames transmitted on the EtherChannel.
Rcv-Octet	Number of octet frames received on the EtherChannel.
Xmit-Octet	Number of octet frames transmitted on the EtherChannel.

Table 2-15 describes the fields in the show channel info output.

Table 2-15 show channel info Command Output Fields 

Field	Description
Chan id	EtherChannel ID
Port	Port number
Status	Port connection status
Channel mode	EtherChannel mode
Admin group	EtherChannel administrative group
Speed	Port speed
Duplex	Port duplex
Vlan	Port VLAN membership
if-index	Interface index number
Oper-group	Capability of the group.
Neighbor Oper-group	Device ID of the neighboring device with which the port is channeling.
Chan cost	EtherChannel spanning-tree port cost
Oper-Distribution Method	EtherChannel frame distribution method
PortSecurity/Dynamic Port	Status of whether the port is secure or dynamic.
Device-ID	Serial number and hostname of neighboring device
Port-ID	Connected port number on neighboring device
Platform	Neighboring device platform
Trunk-status	VLAN trunking mode
Trunk-type	VLAN trunk encapsulation type
Trunk-vlans	Allowed VLAN list for the trunk
Portvlancost-vlans	Spanning-tree port-VLAN cost and associated VLAN IDs
Port priority	Spanning-tree port priority
Portfast	Spanning-tree PortFast enable state
Port vlanpri-vlans	Spanning-tree port-VLAN priority and associated VLAN IDs
IP	IP protocol filtering mode
IPX	IPX protocol filtering mode
Group	Group protocol filtering mode
GMRP status	GMRP enable state
GMRP registration	GMRP registration mode
GMRP forwardAll	GMRP forward-all enable status
GVRP status	GVRP enable state
GVRP registration	GVRP registration mode
GVRP applicant	GVRP applicant mode
Qos-Tx	Transmit queue and threshold port type
Qos-Rx	Receive queue and threshold port type
Qos-Trust	QoS port trust
QoS-DefCos	QoS default CoS

Related Commands

set channel cost
set channel vlancost
set port channel
show channel group
show port channel