Table Of Contents
System Messages and Recovery Procedures
LC_PORT_CHANNEL-SLOT# Messages
System Messages and Recovery Procedures
This chapter includes the system messages for the Cisco MDS 9000 Family, Cisco Nexus 1000V Series, Cisco Nexus 5000 Series, Cisco Nexus 4000 Series, and Cisco Nexus 7000 Series NX-OS products. The messages are listed in alphabetical order by the system facility that produces them. Within each system facility section, messages are listed alphabetically by severity and mnemonics. Each error message is followed by an explanation and a recommended action.
AAA Messages
This section contains the AAA messages.
AAA-1
Error Message AAA-1-AAA_SESSION_LIMIT_REJECT: aaa request rejected as maximum aaa sessions are in progressExplanation An AAA request has been rejected because the system has detected that the limit for the maximum concurrent AAA sessions has been exceeded.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAA-2
Error Message AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of accounting log failed. [chars]Explanation The system has detected that the accounting log upgrade has failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AAA-2-AAA_PROGRAM_EXIT: aaa daemon exiting: [chars]Explanation The system has detected that the AAA daemon has exited.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAA-3
Error Message AAA-3-AAA_NVRAMFAILURE: nvram failureExplanation The system has detected that because the NVRAM cannot be read/written to, the accounting log cannot be stored in NVRAM.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
AAA-6
Error Message AAA-6-AAA_ACCOUNTING_MESSAGE: [chars]Explanation This message indicates that this is an accounting message.
Recommended Action No action is required.
ACL Messages
This section contains the ACL messages.
ACL-2
Error Message ACL-2-ACL_HA_FAILURE: Failed to do high availability operation: [chars].Explanation The system has failed to do a high availability operation. [chars] is the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_INIT_FAILED: Initialization failed for ACL: [chars], reason: [hex].Explanation Initialization failed for ACL due to [chars], reason: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_LINECARD_STATUS: Status from linecard: [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].Explanation This message indicates that this message is a status from the line card [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation: [chars].Explanation The system has failed to do an MTS operation. [chars] is the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_MTS_REGISTRATION_FAILED: MTS options setting to [hex] failed for opCode: [dec].Explanation The MTS options setting to [hex] failed for opCode: [dec].
Recommended Action No action is required.
Error Message ACL-2-ACL_PENDING_MSG_ARR_FULL: ACL Upgrade Pending Messages Array is Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex]Explanation This message indicates that the ACL upgrade pending messages array is full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex].Explanation The system has failed to do a PSS operation [chars]. [hex] is the reason.
Recommended Action No action is required.
Error Message ACL-2-ACL_PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], expected version [dec].[dec].[dec].Explanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] is the expected version.
Recommended Action No action is required.
Error Message ACL-2-ACL_RUNTIME_FAILURE: [chars] [dec], Error: [hex]Explanation The system detects than an ACL runtime failure has occurred as [chars] [dec], reason: [hex].
Recommended Action No action is required.
Error Message ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM operation: [chars].Explanation The system has failed to do a TCAM operation. [chars] is the reason.
Recommended Action No action is required.
ACL-4
Error Message ACL-4-ACL_WARNING: [chars] [dec]Explanation ACL warning messages are reported as [chars] [dec].
Recommended Action No action is required.
ACL-5
Error Message ACL-5-ACL_ADJ_SHARING_STATUS: Successfully completed [chars] on Generation 2 linecards.Explanation Successfully completed the command \[chars]\ on Generation 2 line cards.
Recommended Action No action is required.
ACL-6
Error Message ACL-6-ACL_DIAG_EVENT_STATUS: [chars] [hex].Explanation ACL system health management event status is reported as [chars] [hex].
Recommended Action No action is required.
Error Message ACL-6-ACL_E_PORT_EVENT_STATUS: [chars] [chars].Explanation ACL E port event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars].Explanation ACL FCC event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_LINECARD_EVENT_STATUS: [chars] [hex].Explanation ACL line card event status is reported as [chars] [dec].
Recommended Action No action is required.
Error Message ACL-6-ACL_MCAST_EVENT_STATUS: [chars] [chars].Explanation ACL multicast event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_NX_PORT_EVENT_STATUS: [chars] [chars].Explanation ACL Nx Port event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars] [chars].Explanation ACL portmode event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_RUNTIME_STATUS: [chars] [dec]Explanation ACL runtime status is reported as [chars] [dec].
Recommended Action No action is required.
Error Message ACL-6-ACL_SPAN_DEST_CONFIG_STATUS: [chars] [chars].Explanation ACL SPAN destination config event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars] [chars].Explanation ACL SPAN source configuration event status is reported as [chars] [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_STATUS: ACL Status: [chars].Explanation ACL status is reported as [chars].
Recommended Action No action is required.
Error Message ACL-6-ACL_UPDATE_SSRAM_QOS_EVENT_STATUS: [chars] [chars].Explanation ACL update SSRAM for QoS event status is reported as [chars] [chars].
Recommended Action No action is required.
ACLLOG Messages
This section contains the ACLLOG messages.
ACLLOG-4
Error Message ACLLOG-4-ACLLOG_MAXFLOW_REACHED: [chars]Explanation The maximum flow has been reached in current interval: [chars].
Recommended Action No action is required.
Error Message ACLLOG-4-ACLLOG_THRESHOLD: [chars]Explanation Threshold Reached for Flow: [chars].
Recommended Action No action is required.
ACLLOG-6
Error Message ACLLOG-6-ACLLOG_FLOW_INTERVAL: [chars]Explanation Flow informationin current alert interval: [chars].
Recommended Action No action is required.
Error Message ACLLOG-6-ACLLOG_NEW_FLOW: [chars]Explanation New Acllog Flow: [chars].
Recommended Action No action is required.
ACLMGR Messages
This section contains the ACLMGR messages.
ACLMGR-2
Error Message ACLMGR-2-ACLMGR_COMMIT_FAIL: Commit failed: client %llX, [chars]Explanation The PPF commit failed.
Recommended Action No action is required.
Error Message ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on ifindex [hex] allowed to succeed in spite of access-list failureExplanation Although an access-list operation failed during a port event, the port event still finished successfully because errordisable is disallowed.
Recommended Action No action is required.
Error Message ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on interface [chars] ([hex]) allowed to succeed in spite of access-list failureExplanation Although an access-list operation failed during a port event, the port event still finished successfully because errordisable is disallowed.
Recommended Action No action is required.
Error Message ACLMGR-2-EXITING: Exit reason: [chars]Explanation The ACLMGR service process has exited due to [char]. The process has probably been restarted automatically.
Recommended Action No action is required.
Error Message ACLMGR-2-INITFAIL: ACLMGR Service Init failed: [chars]Explanation ACLMGR Service initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message ACLMGR-2-MALLOC_ERROR: Size [dec] bytesExplanation The ACLMGR service could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLMGR-2-PSS_ERROR: [chars]: PSS ret. val=[dec]Explanation The ACLMGR service encountered an error while operating on a persistent storage database.
Recommended Action No action is required.
ACLMGR-3
Error Message ACLMGR-3-ACLMGR_ACL_ON_FAB_INACTIVE: ACL on FEX fabric interface not activatedExplanation ACL applied to a FEX fabric port or port channel is not activated.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_ACL_OVER_FAB_CHANNEL: ACL on FEX fabric port-channel bound interface not activatedExplanation ACL applied to a FEX interface is not activated if the interface is bound to a FEX-fabric port channel.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_PPF_ERROR: PPF error: [chars]Explanation The PPF generated an error.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_PSS_CORRUPTED: [chars] PSS found corruptedExplanation The ACLMGR service has detected a corrupted file in its persistent information databases The database would be recreated.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_STAT_CONSOLIDATION_FAILURE: ACL statistic parsing or consolidation failedExplanation A statistic update failed during the parsing or consolidation step; statistics may have been lost.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL: VACL redirection to ifindex [hex] disabled: the port has been removedExplanation A VACL redirection to the port has been deactivated because the port has been removed.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL: VACL redirection to interface [chars] ([hex]) disabled: the port has been removedExplanation A VACL redirection to the port has been deactivated because the port has been removed.
Recommended Action No action is required.
Error Message ACLMGR-3-ACLMGR_VERIFY_FAIL: Verify failed: client %llX, [chars]Explanation The PPF Verify failed.
Recommended Action No action is required.
Error Message ACLMGR-3-MTSERROR: [chars]Explanation ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
ACLMGR-4
Error Message ACLMGR-4-ACLMGR_ACL_OVER_FAB_CHANNEL: ACL on FEX fabric port-channel bound interface not activatedExplanation ACL applied to a FEX interface is not activated if the interface is bound to a FEX-fabric port channel.
Recommended Action No action is required.
Error Message ACLMGR-4-ACLMGR_PPF_WARNING: PPF warning: [chars]Explanation The PPF generated warning.
Recommended Action No action is required.
Error Message ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM: VACL redirection to ifindex [hex] disabled: the port became a portchannel memberExplanation A VACL redirection to the port has been temporarily deactivated because it is now a member in a port channel.
Recommended Action No action is required.
Error Message ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM: VACL redirection to interface [chars] ([hex]) disabled: the port became a portchannel memberExplanation A VACL redirection to the port has been temporarily deactivated because it is now a member in a port channel.
Recommended Action No action is required.
Error Message ACLMGR-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec]Explanation There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.
Recommended Action No action is required.
ACLMGR-6
Error Message ACLMGR-6-ACLMGR_PPF_NOTIF: PPF notification: [chars]Explanation The PPF generated a notification.
Recommended Action No action is required.
Error Message ACLMGR-6-BECAME_ACTIVE: Became ACTIVE from standby modeExplanation The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.
Recommended Action No action is required.
Error Message ACLMGR-6-BECAME_STDBY: Became STANDBY from active modeExplanation The ACLMGR service became standby from active mode.
Recommended Action No action is required.
Error Message ACLMGR-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]Explanation The ACLMGR service was unable to send heartbeats to the system manager.
Recommended Action No action is required.
Error Message ACLMGR-6-SERVICE_UP: Initialized [chars]Explanation The ACLMGR service is up and ready The service was initialized in [char] mode.
Recommended Action No action is required.
Error Message ACLMGR-6-SRVEXIT: ACLMGR Service shutting down gracefullyExplanation ACLMGR Service is shutting down gracefully.
Recommended Action No action is required.
Error Message ACLMGR-6-SWITCHOVER: Switching Over to other Sup.Explanation The ACLMGR service has successfully switched over to the standby supervisor module.
Recommended Action No action is required.
ACLQOS-SLOT# Messages
This section contains the ACLQOS-SLOT# messages.
ACLQOS-SLOT#-2
Error Message ACLQOS-SLOT#-2-ACLQOS_FAILED: ACLQOS failure: [chars]Explanation ACLQOS operation failed in the aclqos client.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-ACLQOS_INBAND_INTERFACE_FAILURE: Inband interface lif lookup failed ([chars])Explanation Inband interface lif lookup failed.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-ACLQOS_MALLOC_FAILED: Memory allocation failed. [chars]Explanation Memory allocation failed. This is a critical failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-ACLQOS_OOTR: Tcam resource exhausted: [chars]Explanation TCAM resources to program acls exhausted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-2-PPF_FAILED: Database failure: [chars]Explanation Database operation failed in the aclqos client.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLQOS-SLOT#-3
Error Message ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control parametersExplanation Invalid Congestion Control parameters.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parametersExplanation Invalid Pause parameters.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-3-ACLQOS_QUEUING_ERROR: ACL/QoS queuing error: [chars]Explanation Internal error in ACL/QoS queing configuration.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLQOS-SLOT#-4
Error Message ACLQOS-SLOT#-4-ACLQOS_ATOMIC_ERR: [chars]Explanation TCAM will be overused, turn off atomic update.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_OVER_THRESHOLD: Tcam [dec] Bank [dec]'s usage has reached its thresholdExplanation TCAM is almost full.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_COS2Q_INVALID: ACL/QoS invalid queuing policy because of cos map change: [chars] queue [chars], interface [chars]Explanation Attemped to configure an invalid queuing policy.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_INVALID: ACL/QoS invalid queuing policy: [chars]Explanation Attemped to configure an invalid queuing policy.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-4-ACLQOS_UNDER_THRESHOLD: Tcam [dec] Bank [dec]'s usage is below the threshold nowExplanation TCAM's usage is below the threshold.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLQOS-SLOT#-5
Error Message ACLQOS-SLOT#-5-ACLQOS_DISRUPTIVE_IPv6_UPDATE: Disruptive update of IPv6 compression entriesExplanation Disruptive IPv6 compression entries update.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ACLQOS-SLOT#-5-ACLQOS_NON_ATOMIC: Non atomic ACL/QoS policy update done for [chars]Explanation Nonatomic ACL/QoS policy update was done.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ACLTCAM Messages
This section contains the ACLTCAM messages.
ACLTCAM-2
Error Message ACLTCAM-2-ACL_TCAM_ALMOST_FULL: TCAM close to FULL. [chars] TCAM Usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_CONFIG_READ_FROM_DRIVER_FAILED: [chars] [dec], Error: [hex].Explanation The system is unable to read the configuration from the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_CONFIG_WRITE_TO_DRIVER_FAILED: [chars] [dec], Error: [hex].Explanation The system is unable to write the configuration to the forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database found inconsistent.Explanation Database found inconsistent.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS: TCAM contents found inconsistent.Explanation TCAM contents are found inconsistent.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INIT_FAILED: Initialization failed for forwarding engine ASIC: [dec], [chars] TCAM.Explanation Initialization failed for the forwarding engine ASIC [dec], in [chars] TCAM.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_INIT_REGIONS_FAILED: Initialization failed for forwarding engine ASIC: [dec], [chars] TCAM, [chars] Region.Explanation Initialization of regions failed for the forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MALLOC_FAILURE: Memory allocation failed for size [dec].Explanation Memory allocation is failed for size [dec] bytes.
Recommended Action Restart the process.
Error Message ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation failed: [chars].Explanation MTS operation failed. [chars] is the reason.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS registration failed for opCode: [dec].Explanation MTS registration failed for opCode: [dec].
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed to get route for VSAN: [dec], Rewrite: [chars] DID: [chars] DID MASK: [chars], error: [hex].Explanation ACLTCAM process experienced a failure while getting route for VSAN [dec] Rewrite [chars] DID [chars] DID Mask [chars]. [hex] is the error code.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_NO_TCAM_LEFT: ACLTCAM resource exhausted for interface : [chars]Explanation ACLTCAM hardware resource is completely used.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_FAILED: [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).Explanation [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_INVALID: Invalid([chars], value: [dec]) TCAM entry read from hardware TCAM (FWD-Engine: [dec], [chars] TCAM, Address: [dec]), Ignoring this entry.Explanation Invalid([chars], value: [dec]) TCAM entry from hardware TCAM(FWD-Engine: [dec], [chars] TCAM, Address: [dec]) Ignoring this entry.
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_WRITE_FAILED: [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).Explanation [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).
Recommended Action No action is required.
Error Message ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex].Explanation The system has failed to do a PSS operation [chars]. [hex] is the reason.
Recommended Action No action is required.
Error Message ACLTCAM-2-PSS_OPEN_FAILED: PSS open failed - [hex].Explanation Persistent database handle could not be obtained for ACLTCAM. [hex] is the error.
Recommended Action No action is required.
Error Message ACLTCAM-2-RECONS_FAILED: Reconstruction of TCAM contents failed during upgrade - [hex].Explanation During nondisruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.
Recommended Action No action is required.
ACLTCAM-3
Error Message ACLTCAM-3-REGISTER_FAILED: Could not register to MTS opcode [chars] - error [hex].Explanation ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.
Recommended Action No action is required.
ACLTCAM-4
Error Message ACLTCAM-4-ACL_TCAM_BELOW_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) fell below [dec]% fwd-eng: [dec], [chars]Explanation [chars] TCAM usage [dec]/[dec] fell below [dec] percent on fwd-engine [dec], [chars].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_BEYOND_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_INVALIDATED: Flow counter for flow: vsan: [dec], sid: [hex], did: [hex] with statistics: frames = %llu & bytes = %llu was invalidated due to: [chars]Explanation ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [[chars]].
Recommended Action No action is required.
Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_VALIDATED: Flow counter for flow: vsan: [dec], sid: [hex], did: [hex] is now validExplanation ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].
Recommended Action No action is required.
ACLTCAM-6
Error Message ACLTCAM-6-ACL_TCAM_STATUS: Status: [chars].Explanation ACLTCAM status is reported as: [chars].
Recommended Action No action is required.
AM Messages
This section contains the AM messages.
AM-2
Error Message AM-2-API_INIT Format: Failed to initialize %s APIExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-BAD_TIMER Format: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-CLI_INIT Format: Failed to initialize CLIExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-INIT_FAIL Format: Initialization failureExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MQ_OPEN Format: Failed to open message queue %s: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_BIND Format: Failed to do mts_bind for %s: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_RECV Format: MTS queue receive failed on %s queue: %sExplanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-MTS_SADDR_GET Format: Failed to get source of mts queue %s: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-NO_WORKBIT Format: Failed to register %s too many notify clientsExplanation An unexpected fatal error has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-2-REQD_COMP_DOWN Format: Required component \%s\ has gone down.Explanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-REQD_COMP_FAIL Format: Required component \%s\ has failed to initialize.Explanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SDB_CREAT Format: Failed to create shared databaseExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SDB_DESTROY Format: Failed to destroy shared databaseExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SDB_OPEN Format: Failed to open shared databaseExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SET_SCHED Format: Failed to set policy or priorityExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SHM_CREAT Format: Failed to create shared memory: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SHM_LOCK_CREAT Format: Failed to create shared memory lock: %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SVR_REG Format: Failed to register as a client of %s for VRF %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_NAME Format: Failed to get name from sysmgr during %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_NOTIFY Format: Bad notification from sysmgr for %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_QUERY Format: Failed to query sysmgr for %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-SYSMGR_UUID Format: Failed to get uuid from sysmgr during %sExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-THR_CREAT Format: Failed to create thread %s: error %dExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-THREAD_FAIL Format: Failed to start %s threadExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-2-URIB_PIB Format: Unable to get pib for %s VRF from URIBExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
AM-3
Error Message AM-3-BAD_PARAMS Format: Called %s with address family %d, iod %d, l3address %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-DEL_PROT_ADJ Format: Unable to delete protocol adjacency for %s, uuid %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MAC_REG_FAILED Format: Mac registration with L2FM failed for mac %s, iod %s, phy iod: %sExplanation MAC registration with L2FM failed.
Recommended Action No action is required.
Error Message AM-3-MAX_RETRIES Format: Notification retry limit exceeded for %sExplanation Client is not replying to our notifications.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-3-MQ_RECV Format: Message queue receive failed on %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MQ_SEND Format: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MSG_TO_TLV Format: Notification message to TLV failedExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MTS_DROP Format: MTS drop failed on %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-MTS_SEND Format: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-NO_AF Format: %s: Unable to get address family block for index %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-NO_MEM Format: Malloc failed for %s %sExplanation The system may be low on memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-3-NO_PIB Format: Unable to get pib for client pid %d while processing %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-NO_SMEM Format: Smalloc failed for %s %sExplanation AM's shared memory quota may be used up, due to a large number of adjacencies or a memory leak.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message AM-3-PT_ADD Format: Pt_add failed for %s %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-QUEUE Format: %s failed for %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-READ_LOCK_HOLD Format: %s:%s():%d: Assert, read-lock not acquiredExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-RIB_RTE_CHG Format: Failed to send AM route changes to %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-SHM_OPEN Format: Shared memory does not exist: %sExplanation This message indicates an informational log about a system event.
Recommended Action No action is required.
Error Message AM-3-THR_MUTEX_LOCK Format: Failed to thread mutex lockExplanation Failed function pthread_mutex_lock.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-3-THR_MUTEX_UNLOCK Format: Failed to thread mutex lockExplanation Failed function pthread_mutex_unlock.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message AM-3-TLV_TO_STRUCT Format: Notification TLV to struct failedExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-3-URIB_CNTXT Format: Failed to get %s VRF from URIBExplanation An unrecoverable software error has occurred during the AM initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
AM-5
Error Message AM-5-INVALID_NOTIFY Format: Received invalid notification messageExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MQ_MAJOR Format: Received unknown major message type (%d) from %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MQ_MINOR Format: Received unknown minor message type (%d) from %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MQ_UNEXP Format: Received unexpected message (%d/%d) on %s queueExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MSG_UNK Format: Received unknown % type: %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-MTS_OPC_UNK Format: Received unknown MTS opcode %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message AM-5-REG_DELAY Format: AM register %s delay: %d secondsExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
AM-6
Error Message AM-6-FAILED_STATS Format: Failed to retrieve stats from FTMExplanation This message indicates an informational log about a system event.
Recommended Action No action is required.
Error Message AM-6-SYSMAN_CLEANUP Format: Terminated by SYSMAN cleanup signal ; Explanation: Informational log about a system event.Explanation The system has detected an error.
Recommended Action No action is required.
ARP Messages
This section contains the ARP messages.
ARP-2
Error Message ARP-2-AM_PIB Format: Failed to acquire AM handle %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-AM_REG Format: Failed to register as a client of AM %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-API_INIT Format: Failed to initialize %s APIExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-CLI_INIT Format: Failed to initialize CLIExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-DUP_SRC_IP Format: Source address of packet received from %s on %s(%s) is duplicate of local, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-2-DUP_SRCIP Format: Source address of packet received from %s on %s is duplicate of local, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-2-INIT_FAIL Format: Initialization failureExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MQ_OPEN Format: Failed to open message queue %s: %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MQ_RECV Format: Message queue receive failed on %s queue: %sExplanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MTS_BIND Format: Failed to do mts_bind for %s: %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-MTS_RECV Format: MTS queue receive failed on %s queue: %sExplanation An unexpected fatal error has occurred.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SET_SCHED Format: Failed to set policy or priorityExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SHM_ATTACH Format: Failed to attach %s shared memoryExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SVR_REG Format: Failed to register as a client of %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SYSMGR_NOTIFY Format: Bad notification from sysmgr for %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SYSMGR_QUERY Format: Failed to query sysmgr for %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-SYSMGR_UUID Format: Failed to get uuid from sysmgr during %sExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-THR_CREAT Format: Failed to create thread %s: error %dExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-THREAD_FAIL Format: Failed to start %s threadExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-TIMER_SET Format: Failed to initialize new timer setExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
Error Message ARP-2-TIMERS_INIT Format: Failed to initialize timersExplanation An unrecoverable software error has occurred during ARP initialization.
Recommended Action Use 'reload' command to reload the system. Be aware that this problem affects all VDCs on the system.
ARP-3
Error Message ARP-3-ADJ_ADD Format: Failed to add adjacency for received packet from %s on %sExplanation Due to this failure, packet forwarding to this address will be affected until the next successful retry.
Recommended Action No action is required.
Error Message ARP-3-ADJ_UPD Format: Failed to update adjacency for received packet from %s on %sExplanation Due to this failure, packet forwarding will continue to use the existing ARP adjacency entry values.
Recommended Action No action is required.
Error Message ARP-3-API_MQ_INVAL Format: ARP API Error: Invalid ARP message queue in %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-API_MQ_SEND Format: ARP API Error: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-API_MTS_INVAL Format: ARP API Error: Invalid ARP MTS queue in %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-API_MTS_SEND Format: ARP API Error: Failed to send %s to %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-DUP_VADDR_SRC_IP Format: Source address of packet received from %s on %s(%s) is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-DUP_VADDR_SRCIP Format: Source address of packet received from %s on %s is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-DUP_VIRT_SRC_IP Format: Source address of packet received from %s on %s(%s) is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-DUP_VIRT_SRCIP Format: Source address of packet received from %s on %s is duplicate of local virtual ip, %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-3-GRAT_ETH Format: Sending gratuitous arp for %s on invalid interface %s, not ethernetExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_IOD Format: Sending gratuitous ARP for %s on an invalid interface %uExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_IP Format: Sending gratuitous ARP request for %s IP address %s on %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_NON_AM Format: Sending gratuitous arp for %s on invalid interface %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-GRAT_P2P Format: Sending gratuitous arp for %s on invalid interface %s, point-to-pointExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-HDR_ERR Format: Failed to get ARP header, expected %d, got %d bytesExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-HDR_L2LEN_ERR Format: Received packet with incorrect layer 2 address length (%d bytes)Explanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-HDR_L3LEN_ERR Format: Received packet with incorrect layer 3 address length (%d bytes)Explanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-IF_INDEX Format: Invalid interface index received from %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-INVAL_HDR Format: Found incorrect hardware/protocol type in ARP header: %hu/%huExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-INVAL_STATE Format: Unrecognized ARP entry state in timer callback: %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-MAC_ERR Format: Failed to get MAC address on %s for %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-MBUF_ERR Format: Failed to get the remainder of packet, expected %d, got %d bytesExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-MTS_DROP Format: MTS drop failed on %s queue: %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-NO_MBUF Format: Failed to allocate buffer for %sExplanation The system may have run out of packet memory buffers.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ARP-3-NO_MEM Format: Malloc failed for %s %sExplanation The system may be low on memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ARP-3-PKT_ENCAP Format: Failed to encapsulate packetExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-PKT_OUT Format: Failed to send packet to PMExplanation PM's message queue may be temporarily full.
Recommended Action No action is required.
Error Message ARP-3-REQ_ADD Format: Failed to add adjacency while sending request for %s on %s, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_ETH Format: Sending ARP request for %s on invalid interface %s, not ethernet, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_IOD Format: Sending ARP request for %s on an invalid interface %u, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_IP Format: Sending ARP request for %s IP address %s on %s, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_NON_AM Format: Sending ARP request for %s on invalid interface %s request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-REQ_P2P Format: Sending ARP request for %s on invalid interface %s, point-to-point, request from pid: %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-TIMER_RSTART Format: Failed to restart timer 0x%p for %s on %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_ETH Format: Adding vrrp arp for %s: invalid interface %s, not ethernetExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_IOD Format: Adding vrrp arp for %s: invalid interface %uExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_NON_AM Format: Sending vrrp arp for %s on invalid interface %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRP_P2P Format: Sending vrrp arp for %s on invalid interface %s, point-to-pointExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRPQ_ADD Format: Failed to add VRRP queue entry for %s, %s on %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-3-VRRPQ_IP Format: Trying to add invalid IP address %s on %s to vrrp queueExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
ARP-4
Error Message ARP-4-DIR_BCAST Format: %s address of packet received from %s on %s matches directed broadcast address, %sExplanation There may be a configured subnet mask-length mismatch among router interfaces connected on this LAN.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-DUP_IP Format: ARP entry found with duplicate IP address %s on %sExplanation There may be another router on this network that is configured with the same IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-INVAL_IP Format: Received packet with invalid %s IP address (%s) from %s on %sExplanation There may be a connected router sending packets with a bogus IP address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-INVAL_MAC Format: Received packet with invalid %s MAC address (%s) from %s on %sExplanation There may be a connected router sending packets with a bogus MAC address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-OWN_SRCMAC Format: Received packet with a local source MAC address (%s) from %s on %sExplanation There may be a connected router sending packets with local MAC address.
Recommended Action Check all routers on the interface for a misconfiguration.
Error Message ARP-4-SRCIP_ERR Format: Source address of received packet (%s) does not match subnet on interface %sExplanation There may be a configured subnet mismatch among router interfaces connected on the LAN.
Recommended Action Check all routers on the interface for a misconfiguration.
ARP-5
Error Message ARP-5-MQ_MINOR Format: Received unknown minor message type (%d) from %sExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-MQ_UNEXP Format: Received unexpected message (%d/%d) on %s queueExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-MSG_UNK Format: Received unknown % type: %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-MTS_OPC_UNK Format: Received unknown MTS opcode %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-UNK_IP_NOTIF Format: Unrecognized IP address change notification type %luExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-UNK_MSG_MINOR Format: Unrecognized %s message minor type %dExplanation An unexpected but recoverable error has occurred.
Recommended Action No action is required.
Error Message ARP-5-UNK_SIG Format: Received unknown signal %d ; Explanation: An unexpected but recoverable error has occurred.Explanation The system has detected an error.
Recommended Action No action is required.
ARP-6
Error Message ARP-6-SYSMAN_CLEANUP Format: Terminated by SYSMAN cleanup signal ; Explanation: Informational log about a system event.Explanation The system has detected an error.
Recommended Action No action is required.
ASCII-CFG Messages
This section contains the ASCII-CFG messages.
ASCII-CFG-2
Error Message ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error encountered while Ascii configuration was being applied. Please use show startup-config log to view detailsExplanation At least one command failed while the ASCII configuration was being applied.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_LIB_INVOKE_ERR: Ascii config library invocation error: [chars]Explanation The system has encountered an error while the library function was being invoked to display the ASCII configuration.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_ROLLBACK_FAILED: rollback operation failed for atomic optionExplanation Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Recommended Action Rollback.
Error Message ASCII-CFG-2-ACFG_ROLLBACK_FAILED: Rollback to checkpoint [chars] Failed, Going to undo the changes (atomic option)Explanation Rollback operation failed for atomic option.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_ROLLBACK_UNDO_FAILED: Undo failed for atomic Rollback, Please correct the error manually and retry rollbackExplanation The system has encountered an error while undoing the rollback changes (for atomic behavior.
Recommended Action No action is required.
Error Message ASCII-CFG-2-ACFG_SYSLOG_INIT_FAILED: Ascii config Syslog Init ErrorExplanation The system has encountered an error while initializing the syslog for the ASCII configuration.
Recommended Action No action is required.
ASCII-CFG-3
Error Message ASCII-CFG-3-ACFG_MTSERROR: [chars]Explanation Ascii-cfg-server (rollback process) encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
ASCII-CFG-6
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE: cleared all the configuration checkpointsExplanation The system has cleared all the configuration checkpoints.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CREATED: created configuration checkpointExplanation Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CREATED: Created configuration checkpoint [chars]Explanation The system has created a configuration checkpoint.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_DELETE_ALL: Deleted all the configuration checkpointsExplanation The system deleted all the configuration checkpoints.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_DELETED: deleted configuration checkpointExplanation Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII-CFG-6-ACFG_CHECKPOINT_DELETED: Deleted configuration checkpoint [chars]Explanation The system has deleted the configuration checkpoint.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_MAX_CHECKPOINTS: Maximum no of checpoints reached, Removing the oldest checkpointExplanation The system detects that the maximum number of checkpoints has been reached and has removed the oldest checkpoint.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_ATOMIC: Performing configuration rollback to checkpoint [chars] (with atomic option)Explanation The system will perform a configuration rollback with the atomic option.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_ATOMIC: Performing configuration rollback with atomic optionExplanation Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_BEST: Performing configuration rollback to checkpoint [chars] (with best-effort option)Explanation The system will perform a configuration rollback with the best-effort option.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_BEST: Performing configuration rollback with best-effort optionExplanation Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_FIRST_ERR: Performing configuration rollback to checkpoint [chars] (with stop-at-first failure option)Explanation The system will perform a configuration rollback with the stop-at-first-failure option.
Recommended Action No action is required.
Error Message ASCII-CFG-6-ACFG_ROLLBACK_FIRST_ERR: Performing configuration rollback with stop-at-first-failure optionExplanation Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
ATIMERS Messages
This section contains the ATIMERS messages.
ATIMERS-3
Error Message ATIMERS-3-ERROR Format: %sExplanation An active timer API has detected an error
Parameters: Error ...Recommended Action No action is required.
Error Message ATIMERS-3-OPER Format: timer failed to %s, error %sExplanation An active timer API has detected an error
Parameters: timer operation, reason ...Recommended Action No action is required.
Error Message ATIMERS-3-START Format: starting timer 0x%p: heap not allocated for set id %uExplanation An active timer API has detected an error
Parameters: timer, Set ID ...Recommended Action No action is required.
Error Message ATIMERS-3-STOP Format: stopping timer 0x%p: heap not allocated for set id %u\nExplanation An active timer API has detected an error
Parameters: timer, Set ID ...Recommended Action No action is required.
BGP Messages
This section contains the BGP messages.
BGP-1
Error Message BGP-1-FATAL Format: Fatal error: %s: %sExplanation An unexpected fatal error has occurred.
Parameters: Error Type, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-1-UNKNOWNFATAL Format: Unknown fatal error %d: %sExplanation An unexpected fatal error has occurred.
Parameters: Error Type, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
BGP-2
Error Message BGP-2-AFINIT Format: Error initializing address family, (%d)Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-AFINITFUNCS Format: Error initializing address family function vectors, (%d)Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-APIINIT Format: Unable to initialize %s APIExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-APIMTSBIND Format: Unable to bind to MTS SAP for %s, sap %d: %sExplanation BGP client was not able to create a message queue for communication.
Parameters: Queue name, MTS SAP, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-ATTACH Format: Unable to attach to %sExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-IPV6REG Format: Unable to register with IPv6Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-MQLOOP_INIT Format: Message queue loop %s, %s, Error - %sExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: MQLoop Type, Failure Type, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-MTSBIND Format: Unable to bind to MTS SAP for %s, sap %d: %sExplanation BGP was not able to create a message queue for communication.
Parameters: Queue name, MTS SAP, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-PEERSHALTED Format: BGP %s shutdown due to no memory condition (%s)Explanation The system may be low on memory.
Parameters: Peer(s), Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-2-PTHREAD Format: procket_pthread_create failed for %s: error %dExplanation An unexpected fatal error has occurred.
Parameters: Thread Name, Error ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-SRVREG Format: Unable to register with %sExplanation An unrecoverable error has occurred during BGP initialization.
Parameters: Server Name ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-SYSMGR_CONDVERIF Format: Sysmgr conditional verify failedExplanation An internal software error occurred.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-SYSMGR_QUERY Format: Failed to query sysmgr for %sExplanation An internal software error occurred.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-TSP_INIT Format: Unable to initialize with TSPExplanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-U6RIBREG Format: Unable to register with U6RIB for [afi/safi:%d/%d]Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-2-URIBREG Format: Unable to register with URIB for [afi/safi:%d/%d]Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
BGP-3
Error Message BGP-3-ACLTESTADD Format: Failed to add %s peer policy testExplanation An internal software error occurred.
Parameters: ACL type ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-AGGADD Format: [%s] Couldn't add aggregate for %s/%dExplanation BGP was unable to store an aggregate in an internal datastructure. The BGP process may have run out of memory.
Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-AGGDEL Format: [%s] Couldn't delete aggregate for %s/%dExplanation An unexpected but handleable event has occurred.
Parameters: Address-family, Prefix/masklength ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ALLOCFAIL Format: %s malloc (%ld) failed for: %sExplanation The system may be low on memory.
Parameters: Alloc Type, Size, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-API_UNEXP_RESP Format: Received unexpected message from SAP %d, opcode %d, address %s, ignore itExplanation An unexpected but handleable event has occurred.
Parameters: MTS SAP, MTS Opcode, IP Address ...Recommended Action No action is required.
Error Message BGP-3-APIASSERT Format: %s:%d: Assertion `%s' failed.Explanation An internal software error occurred.
Parameters: File Name, Line Number, Assert Type ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-APIMTSDROP Format: MTS drop failed on %s queue: %sExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-APIMTSRECV Format: MTS receive failed on %s queue: %sExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, Error ...Recommended Action No action is required.
Error Message BGP-3-APIMTSSEND Format: MTS send() error to SAP %d, opcode %d: %sExplanation An unexpected but handleable event has occurred.
Parameters: MTS SAP, MTS Opcode, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-APPLY_BESTPATH_CFG Format: Failed to apply bestpath configuration: %sExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ASLEN Format: AS-PATH prepend length exceeds internal limitExplanation The system has exceeded an internal limit when prepending an AS path.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ASSERT Format: %s:%d: Assertion `%s' failed.Explanation An internal software error occurred.
Parameters: File Name, Line Number, Assert Type ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ATTRAVL_OP Format: Failed attribute external database operation: %s, id %luExplanation BGP was unable to perform an attribute external database operation
Parameters: Operation, Attr ID ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ATTRID_OP Format: Failed to %s attribute IDExplanation BGP was unable to allocate or free an index for a BGP PATH attribute block
Parameters: Allocate or free ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BADPEERAS Format: VRF %s, Peer %s - bad remote-as, expecting %s received %s.Explanation The system has detected an error when prepending to an AS path.
Parameters: Segment Type, Segment Length ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-BRIB_ADD_INT Format: Internal error in adding to BRIB: %sExplanation An internal error was encountered in adding a path to the BRIB. The BGP process may have run out of memory.
Parameters: Error ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-BRIB_RDADD Format: [%s] Couldn't add rdinfo %s to BRIBExplanation BGP was unable to add a prefix to the BGP RIB. The BGP process may have run out of memory.
Parameters: Address-family, RDinformation...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-BRIBADD Format: [%s] Couldn't add dest to BRIB for %s/%dExplanation BGP was unable to add a prefix to the BGP RIB. The BGP process may have run out of memory.
Parameters: Address-family, Prefix/masklength ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-BRIBDEL Format: [%s] Couldn't delete dest from BRIB for %s/%dExplanation An unexpected but handleable event has occurred.
Parameters: Address-family, Prefix/masklength ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-CLISET Format: Unable to set %s inheritance for %sExplanation An internal software error occurred.
Parameters: Template type, Peer address ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-COMADD Format: Error occurred in community addition, no action takenExplanation An internal error was encountered in adding a community.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-COMLEN Format: Community sets exceeded maximum allowed limitExplanation An internal limit was hit in adding a community.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-CONDSRV_CLEANUP Format: Conditional Service cleanup request failed, %sExplanation Sysmgr rejected BGP's request to shut down.
Recommended Action No action is required.
Error Message BGP-3-DAMPCFG Format: Both policy and global dampconf existExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-EBGPTTL Format: Unable to set EBGP TTL for peer %s, fd %dExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-EVENT_WAIT Format: Error while waiting for %s event, error - %s\nExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-FINDAGGR Format: [%s] Did not find aggregate path for entry %s/%dExplanation BGP was unable to find an internal datastructure for originating a configured aggregate.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ILLARGS Format: %s called with illegal argumentsExplanation An internal software error occurred.
Parameters: Function ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-INTERNAL Format: Internal error %d: %sExplanation An internal software error occurred.
Parameters: Error Type, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-INVHDR Format: Peer %s sent unexpected header patternExplanation The marker pattern in the message header was invalid.
Recommended Action Check that the peer router is configured correctly. Clear the peer if necessary after any change.
Error Message BGP-3-IPTOS Format: Unable to set IP TOS bits for %s, fd %dExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-LIST Format: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-LISTEN_SOCK Format: Failed to listen on %s BGP TCP portExplanation BGP_EXPL_SOCK_ERROR
Parameters: Address-family ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-LOWMEM Format: Low on heap memoryExplanation The system may be low on memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-MD5PASS Format: Cannot set MD5 password %s for peer %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-MQLOOP_SHUTDOWN Format: Couldn't shut down %s message queue loopExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-MTSDROP Format: MTS drop failed on %s queue: %sExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-MTSRECV Format: MTS receive failed on %s queue: %sExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, Error ...Recommended Action No action is required.
Error Message BGP-3-MTSSEND Format: MTS send() error to SAP %d, opcode %d: %sExplanation An unexpected but handleable event has occurred.
Parameters: MTS SAP, MTS Opcode, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NBRERR Format: %s Peer error: %sExplanation An internal software error occurred.
Parameters: Peer address, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NEGWRITE Format: Negative nr of %d bytes left to write to peer %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NEXTHOPADD Format: [%s] Couldn't add next-hop to RNHDB for %s/%d, error %dExplanation The router was unable to store a BGP next hop in an internal database, because it ran out of memory.
Parameters: Address-family, Prefix/masklength, Error ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-NEXTHOPDEL Format: [%s] Couldn't delete next-hop from RNHDB for %s/%d, error %dExplanation An unexpected but handleable event has occurred.
Parameters: Address-family, Prefix/masklength, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NOBUF Format: [%s] Unable to get buffer for %s msg to peer %sExplanation An internal software error occurred.
Parameters: Address-family, Msg Type, Peer address ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NOMEMORY Format: Could not allocate %sExplanation The system may be low on memory.
Parameters: Data Type ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-NONBESTPATH Format: [%s] Non bestpath in attr. path chain for %s/%dExplanation An internal software error occurred.
Parameters: Address-family, Prefix/masklength ...Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-PATH_DEL Format: Failed to destroy path (%s), error %dExplanation The BGP process may have run out of memory.
Parameters: Path Type, Error ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-PATH_STALE Format: [%s] %s path being %s, for %s/%d from peer %s, should not be staleExplanation An internal software error occurred.
Parameters: Address-family, Path State, Operation, Prefix/masklength, Peer address ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PEER Format: Peer %s, failed %sExplanation An internal software error occurred.
Parameters: Peer address, Operation ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PFX_NOMEM Format: Could not allocate %s for %s/%dExplanation The system may be low on memory.
Parameters: Data Type, Prefix/masklength ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PLCYOUT Format: Cannot add reference to policy out info for route-map %sExplanation Use the 'restart' command to restart the feature and clear this problem.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PLCYRNHATTACH Format: Couldn't attach to policy RNH info for policy %s, error: %sExplanation An internal error occurred in using a policy. BGP_EXPL_NO_MEM_MAYBE.
Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-PLCYRNHDETACH Format: Couldn't detach from policy RNH info for policy %s, error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-PLCYRNHSETUP Format: Couldn't setup rnh notifications for policy %s, error: %sExplanation An internal error occurred in using a policy. BGP_EXPL_NO_MEM_MAYBE.
Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-RDINFO Format: VRF %s, %s, table %s: rdinfo %s failedExplanation BGP was unable to initialize an internal datastructure. The BGP process may have run out of memory.
Parameters: VRF name, Address-family, Table name, Operation ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-RESTARTINIT Format: Unable to determine restart status and initializeExplanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-RESTARTTYPE Format: Error in learning restart typeExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-RNHCB Format: RNH %s error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-RPMBIND Format: RPM policy bind failed for %s %sExplanation An unexpected but handleable event has occurred.
Parameters: Policy type, Policy name ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-RPMHANDLE Format: RPM notification handle does not match existing handle for policy %sExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SENDBUF Format: Error manipulating sendbuf: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SNMP_API_DATA Format: Message data is NULLExplanation An SNMP message does not have enough memory to store data.
Recommended Action No action is required.
Error Message BGP-3-SOCK_ACCEPT Format: Socket (%d/%d) accept: %s\nExplanation BGP_EXPL_SOCK_ERROR
Parameters: Socket fds, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCK_ERR Format: Socket (%d/%d): %s\nExplanation BGP_EXPL_SOCK_ERROR
Parameters: Socket fds, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKBIND Format: Cannot bind local socket for peer %s: %sExplanation An error occurred during a socket operation.
Parameters: Peer address, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKCREATE Format: Cannot create socket for peer %s: %sExplanation An error occurred during a socket operation.
Parameters: Peer address, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKNONBLOCK Format: Couldn't make fd %d non-blocking: %sExplanation An error occurred during a socket operation.
Parameters: Socket fd, Error ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOCKOPEN Format: TCP connection for peer %s already open, fd %d, state %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-SOFTINCAP Format: Peer %s not capable of soft refresh in, operator intervention needed: %sExplanation The router is unable to do a soft refresh for the indicated peer.
Recommended Action If necessary, reset the connection with the peer.
Error Message BGP-3-SRAND Format: Failed to set random seedExplanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-TBLATTRAVL_OP Format: Failed table attribute database operation: %s, id %luExplanation BGP was unable to perform a table attribute database operation
Parameters: Operation, Attr ID ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-TBLAVL_OP Format: Failed table database operation: %s, table %s id %luExplanation BGP was unable to perform a table database operation.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-TBLCTX_INIT Format: VRF %s, %s, table %s: Table initialization failedExplanation BGP was unable to initialize an internal datastructure. The BGP process may have run out of memory.
Parameters: VRF name, Address-family, Table name ...Recommended Action If BGP ran out of memory, add memory to the router or change the network configuration to decrease memory requirements. Clear any BGP peers that may have been shut down automatically. If BGP has available memory, restart BGP.
Error Message BGP-3-THREAD_SHUTDOWN Format: Problem shutting down thread %s: Operation - %s, Error - %s\nExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-TIMER_START Format: Couldn't start %s timer %sExplanation An internal software error occurred.
Parameters: Timer Type, Data ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-U6RIBRNH Format: U6RIB RNH error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-ULIBREG Format: Unable to register with ULIB for [afi/safi:%d/%d]Explanation An unrecoverable error has occurred during BGP initialization.
Recommended Action Use the 'restart' command to restart the feature and clear this problem.
Error Message BGP-3-ULIBRNH Format: ULIB RNH error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-URIBRNH Format: URIB RNH error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-URIBRT Format: URIB RT error: %sExplanation An internal software error occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-VRF_CTX Format: VRF %s, failed %sExplanation An internal software error occurred.
Parameters: VRF Name, Operation ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-3-VRFAVL_OP Format: Failed vrf database operation: %s, vrf %s id %luExplanation BGP was unable to perform a vrf database operation.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BGP-4
Error Message BGP-4-APIMTSNOMSG Format: No MTS payload found on %s queue, opc %dExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, MTS Opcode ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-ISSU_CHECK Format: Not ready for ISSU: Graceful Restart or hold time check failedExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-ISSU_HOLDTIME Format: ISSU will be affected if hold time is less than system switchover time (%d seconds)\nExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-MAXPEERS Format: Trying to configure more than %d neighborsExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-MQUNEXPECT Format: Recieved unexpected message (%d/%d) on %s queueExplanation An unexpected but handleable event has occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-MTSNOMSG Format: No MTS payload found on %s queue, opc %dExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, MTS Opcode ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-MTSUNKOPC Format: Recieved unknown MTS message on %s queue, opc %dExplanation An unexpected but handleable event has occurred.
Parameters: Queue name, MTS Opcode ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-NODAMPMEM Format: [%s] Unable to dampen prefix %s/%d from peer %s due to no memoryExplanation BGP_EXPL_NO_MEMORY
Parameters: Address-family, Prefix/masklength, Peer address ...Recommended Action No action is required.
Error Message BGP-4-NORID Format: Peer %s sent us 0.0.0.0 as its router-idExplanation A BGP peer sent us an invalid router ID.
Recommended Action Check that the peer router is configured correctly. Clear the peer if necessary after any change.
Error Message BGP-4-PFXEXCEED Format: [%s] No. of prefix received from %s exceeded configured limit %dExplanation A peer sent more routes than BGP was configured to accept.
Parameters: Address-family, Peer, Prefix limit ...Recommended Action Check that the peer router is configured correctly. Clear the peer if necessary after any change.
Error Message BGP-4-PFXWARN Format: [%s] Number of prefixes received from %s reached %d, maximum %dExplanation The number of routes sent to us by a peer exceeded the threshold at which BGP should generate a warning.
Parameters: Address-family, Peer, Warning limit, Max limit ...Recommended Action Check that the peer router is configured correctly. Clear the peer if necessary after any change.
Error Message BGP-4-SAMERID Format: Peer %s uses same routerid as usExplanation A BGP peer is using the same router ID as this router.
Recommended Action Configure either the local or remote router with a different router ID.
Error Message BGP-4-SLAB_HOLD Format: Not able to hold element from %s slabExplanation The system has detected an error.
Parameters: Memory slab name ...Recommended Action No action is required.
Error Message BGP-4-SNMP_DEREGFAIL Format: Failed to deregister MIB with the SNMP agent (%s).\nExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-SNMP_REGFAIL Format: Failed to register MIB with the SNMP agent, the BGP MIB will be unavailable. (%s)\nExplanation No user action is required.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BGP-4-TXLIST Format: %sExplanation An unexpected but handleable event has occurred.
Parameters: Error message related to txlist ...Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BGP-5
Error Message BGP-5-ADJCHANGE Format: neighbor %s %s %sExplanation A BGP session has just been established. Or a session has just been shutdown.
Parameters: Neighbor address, Up or Down, Reason ...Recommended Action No action is required.
Error Message BGP-5-BADSIG Format: Should not have received signal %dExplanation An unexpected but handleable event has occurred.
Recommended Action No action is required.
BGP-6
Error Message BGP-6-BADASPATH Format: Long AS path %s received from peer %s: more than configured maxas-limit %dExplanation Session can be brought up due to maximum-peer limit.
Recommended Action No action is required.
Error Message BGP-6-EXIT_DECONFIG Format: BGP process exiting due to deconfigurationExplanation The indicated BGP process has been deconfigured.
Recommended Action No action is required.
Error Message BGP-6-EXIT_RESTART Format: BGP process exiting due to manual restartExplanation The indicated BGP process is being restarted.
Recommended Action No action is required.
Error Message BGP-6-EXIT_UNKNOWN Format: BGP process exiting due to unknown reasonExplanation The system has detected an error.
Recommended Action No action is required.
Error Message BGP-6-MEMSTAT Format: Hit low memory condition - Free: %u MB, Min free: %u MBExplanation The system has detected an error.
Parameters: Current The system free memory, Minimum System free memory ...Recommended Action No action is required.
Error Message BGP-6-PATH_MAXASLIMIT Format: [%s] Path for %s/%d from peer %s found to %s the maxas-limitExplanation The system has detected an error.
Parameters: Address family, Prefix Masklength, EBGP Peer that sent the route, Maxas-limit check result ...Recommended Action No action is required.
Error Message BGP-6-START Format: BGP process %s startup, reason: %sExplanation The indicated BGP process has started.
Parameters: Process name, Reason ...Recommended Action No action is required.
BIOS_DAEMON Messages
This section contains the BIOS_DAEMON messages.
BIOS_DAEMON-2
Error Message BIOS_DAEMON-2-BIOS_DAEMON_FLASH_WARNING: Flash chip not supported by running image. Skipping bios upgrade.Explanation BIOS CHIP NOT SUPPORTED.
Recommended Action No action is required.
Error Message BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: Primary BIOS is corrupted or un-bootableExplanation The system detects that the primary BIOS has been corrupted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-2-BIOS_DAEMON_SUP_ERROR: BIOS Sector ([dec]) is write protectedExplanation The system detects that the BIOS write has been protected.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BIOS_DAEMON-SLOT# Messages
This section contains the BIOS_DAEMON-SLOT# messages.
BIOS_DAEMON-SLOT#-2
Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_ERROR: BIOS Sector ([dec]) is write protectedExplanation The system detects that the BIOS write has been protected.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_PRI_BOOT_FAIL: Primary BIOS is corrupted or un-bootableExplanation The system detects that the primary BIOS has been corrupted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
BOOTUP_TEST Messages
This section contains the BOOTUP_TEST messages.
BOOTUP_TEST-2
Error Message BOOTUP_TEST-2-EOBC_FAIL: Module [dec] has failed test [chars] on EOBC due to error [chars]Explanation The online diagnostic EOBC test has failed.
Recommended Action No action is required.
Error Message BOOTUP_TEST-2-EOBC_SKIP: Module [dec] has failed test [chars] on EOBC due to error [chars]Explanation The online diagnostic ManagementPort test has failed.
Recommended Action No action is required.
Error Message BOOTUP_TEST-2-MGMT_PORT_FAIL: Module [dec] has failed test [chars] on Management Port due to error [chars]Explanation The online diagnostic ManagementPort test has failed.
Recommended Action No action is required.
Error Message BOOTUP_TEST-2-MGMT_PORT_SKIP: Module [dec] has skipped test [chars] on Management Port due to error [chars]Explanation The online diagnostic ManagementPort test is skipped.
Recommended Action No action is required.
BOOTVAR Messages
This section contains the BOOTVAR messages.
BOOTVAR-2
Error Message BOOTVAR-2-ALLOC_MEMORY: Memory allocation failedExplanation The service failed to allocate memory.
Recommended Action Check if the system is low on memory, if so, reset the switch.
Error Message BOOTVAR-2-AUTOCOPY_FAILED: Autocopy of file [chars] to standby failed. [chars] (Error-id: [hex])Explanation The image to be copied to standby vi the auto-copy feature failed.
Recommended Action Check error id for specified reason.
Error Message BOOTVAR-2-AUTOSYNC_FAILED: Image autosync failed. Reason: [chars] ([hex])Explanation Image synchronization failed.
Recommended Action Check that there is enough space on the flash, and check the system high availability status.
Error Message BOOTVAR-2-CONFIG_ERROR: Failed to update boot configurationExplanation An error has occurred during the update of the boot configuration files.
Recommended Action Check that there is enough space on the flash, enter the show boot command to check the configured image names, enter the show loader internal command to compare the configurations, if the configurations do not match, enter the write erase command and retry saving the configuration.
Error Message BOOTVAR-2-IMAGE_NOT_COMPATIBLE: Warning: image [chars] is not compatible with the current platform in SUP [dec]Explanation The input image name is not compatible with the current platform.
Recommended Action Make sure that the system has the correct image before you reboot.
BOOTVAR-3
Error Message BOOTVAR-3-AUTOCOPY_FAILED_STANDBY_FULL: Autocopy of file [chars] to standby failed due to not enough disk space on standbyExplanation There is not enough disk space on the standby for the file to be copied.
Recommended Action Clear space on the standby disk.
Error Message BOOTVAR-3-INIT_FAILED: Initialization failed: Component [chars]Explanation The system detects that the service has failed to start. The failure occurs during initialization of the component [chars].
Recommended Action Enter the show processes command to check the status of the other processes, pay attention to the specified component.
Error Message BOOTVAR-3-LOAD_VERIFY_LIB_FAILED: Fetching library [chars] failed, reason=[chars]Explanation The system has failed to load bootvar that is specified in the verification library.
Recommended Action No action is required.
Error Message BOOTVAR-3-MODULE_LOCK_FAIL: Unable to get module lock, please don't reload <error-id:[hex]>Explanation The system is unable to acquire modlock to prevent the user to reload duringautosynchronization.
Recommended Action No action is required.
Error Message BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY: auto-copy failed - not supported by neighbor supervisor.Explanation The autocopy has failed because it is not supported by the standby supervisor module.
Recommended Action No action is required.
Error Message BOOTVAR-3-VERIFY_FAILED: Image [chars] for bootvar [chars] verification failed, reason=[chars]Explanation The image set for this bootvar has failed the verification process.
Recommended Action Check reason to determine actions.
BOOTVAR-5
Error Message BOOTVAR-5-AUTOCOPY_SUCCEED: auto-copy of file [chars] to standby supervisor succeedExplanation The autocopy of the file has succeeded. The image integrity has been verified by the standby supervisor module.
Recommended Action No action is required.
Error Message BOOTVAR-5-AUTOCOPY_VERIFY_SEND_FAILED: Unable to ask standby to verify file [chars], error = [hex]Explanation When the image was copied to the standby supervisor module, the system failed to ask the standby supervisor module to verify the integrity of the image.
Recommended Action Turn auto-copy off and back on.
Error Message BOOTVAR-5-AUTOSYNC_DONE: Image autosync doneExplanation The image synchronization was successful.
Recommended Action No action is required.
Error Message BOOTVAR-5-AUTOSYNC_REBOOT: Rebooting standby after successful autosyncExplanation The image autosynchronization has been successful. The system is resetting the standby supervisor to load the new image.
Recommended Action Check that the standby supervisor module reloads correctly.
Error Message BOOTVAR-5-AUTOSYNC_START: Starting image autosync. Please wait until completion...Explanation The standby supervisor module has requested the synchronizationof the current image.
Recommended Action No action is required.
Error Message BOOTVAR-5-IMAGE_NOTEXISTS: Warning: image [chars] doesn't exist on sup[dec]Explanation The input image name does not exist on the specified supervisor.
Recommended Action Check whether the input image name you entered exists and make sure that you have the image on the flash before you reboot.
Error Message BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor supervisor, starting...Explanation The information log reports that the standby supervisor module supports autocopy. Autocopy is being started.
Recommended Action No action is required.
BOOTVAR-6
Error Message BOOTVAR-6-ALREADY_IN_SYNC: Image already in syncExplanation This message indicates that you do not need to update the image on the standby supervisor module.
Recommended Action No action is required.
Error Message BOOTVAR-6-CONFIG_UPDATED: Boot configuration updatedExplanation The boot-loader configuration files have been successfully updated.
Recommended Action No action is required.
Error Message BOOTVAR-6-STARTING: Boot configuration initializedExplanation The service has successfully started.
Recommended Action No action is required.
CALLHOME Messages
This section contains the CALLHOME messages.
CALLHOME-2
Error Message CALLHOME-2-EVENT: [chars]Explanation A Call Home event [chars] occurred.
Recommended Action If you have configured your e-mail address to receive Call Home notifications, check your email for more details about this callhome event. If callhome was not enabled, execute commands relevant to the callhome event to get more information about the error.
Error Message CALLHOME-2-PROGRAM_EXIT: callhome process ending: [chars]Explanation A Call Home process is exiting with the reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CALLHOME-3
Error Message CALLHOME-3-CALLHOME_CFS_MERGE_OPERATION_FAILED: [chars]Explanation [chars1].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CALLHOME-3-CALLHOME_CFS_OPERATION_FAILED: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CALLHOME-3-CALLHOME_MAX_ALERT_MSG: [chars]Explanation [chars].
Recommended Action Check the reason for the generation of the Call Home messages and fix the problem.
Error Message CALLHOME-3-EVENT_PROCESS_ERROR: error in processing callhome event [chars] reason:[chars]Explanation An error has occurred when processing the Call Home event [chars] reason:[chars].
Recommended Action Check that Call Home is properly configured on your system. Check the SMTP server address, e-mail addresses for destination profiles and enable Call Home. Use show Call Home commands for displaying the configuration.
Error Message CALLHOME-3-MESSAGE_SIZE_EXCEED: message size for callhome alert:[chars] exceeds maximum limit for destination profile:[chars]Explanation The message size for Call Home alert:[chars] exceeds the maximum limit for destination profile:[chars].
Recommended Action Check the maximum message size for the destination profile . Increase it if possible to match the maximum limit allowed by your e-mail destinations.
CALLHOME-6
Error Message CALLHOME-6-NONCRIT_EVENT: [chars]Explanation A noncritical Call Home event [chars] occurred.
Recommended Action If you have configured your e-mail address to receive Call Home notifications, check your email for more details about this callhome event. If callhome was not enabled, execute commands relevant to the callhome event to get more information about the error.
CDP Messages
This section contains the CDP messages.
CDP-2
Error Message CDP-2-INITFAIL: CDP Daemon Initialization failed: [chars]Explanation CDP daemon initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
CDP-3
Error Message CDP-3-ALLOCFAIL: Heap Memory allocation failed: [chars]Explanation The CDP daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CDP-3-GENERROR: [chars]Explanation The CDP daemon encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.
Recommended Action No action is required.
Error Message CDP-3-MCASTBINDFAIL: Failed to bind for CDP multicast address on interface [hex] - [chars]Explanation An attempt to register for packets destined to the CDP multicast address failed. [dec] identifies the interface and [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-MTSERROR: [chars]Explanation The CDP daemon encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message CDP-3-PKTRECVFAIL: Failed to receive packet - [chars]Explanation The system has failed to receive the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-PKTSENDFAIL: Failed to send packet, interface [hex] - [chars]Explanation The system has failed to send the packet. [dec] identifies the interface and [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-PSSERROR: [chars]Explanation The CDP daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CDP-3-SOCKBINDFAIL: Failed to bind to raw socket, interface [hex] - [chars]Explanation The system has failed to bind to a raw socket. [dec] identifies the interface and [char] identifies the reason.
Recommended Action No action is required.
Error Message CDP-3-SOCKOPENFAIL: Failed to open socket for receiving raw 802_2 packets - [chars]Explanation An attempt to open a socket for receiving raw 802_2 packets failed. [char] identifies the reason.
Recommended Action No action is required.
CDP-4
Error Message CDP-4-DUPLEX_MISMATCH: Duplex mismatch discovered on [chars], with [chars]Explanation A duplex mismatch has been discovered from the received CDP packet.
Recommended Action No action is required.
Error Message CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on [chars]([dec]), with [chars]([dec])Explanation A native VLAN mismatch has been discovered.
Recommended Action No action is required.
CDP-5
Error Message CDP-5-DISABLED: CDP is disabledExplanation CDP is disabled on the device.
Recommended Action No action is required.
Error Message CDP-5-ENABLED: CDP is enabledExplanation CDP is enabled on the device.
Recommended Action No action is required.
CDP-6
Error Message CDP-6-CDPDUP: CDP Daemon Up.Explanation The CDP daemon was created successfully and is up and running.
Recommended Action No action is required.
Error Message CDP-6-CDPEXIT: CDP Daemon shutting down gracefully.Explanation The CDP daemon is shutting down gracefully.
Recommended Action No action is required.
Error Message CDP-6-NEIGHBOR_ADDED: Device [chars] discovered of type [chars] with port [chars] on incoming port [chars] with ip addr [chars] and mgmt ip [chars]Explanation The system discovered a neighbor device.
Recommended Action No action is required.
Error Message CDP-6-NEIGHBOR_REMOVED: CDP Neighbor [chars] on port [chars] has been removedExplanation The system deleted a neighbor device.
Recommended Action No action is required.
Error Message CDP-6-PORTDISABLE: CDP disabled on port [chars]Explanation CDP was disabled on a given port. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
Error Message CDP-6-PORTDOWN: A CDP enabled port [chars] went down.Explanation A CDP enabled port became unoperational. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
Error Message CDP-6-PORTENABLE: CDP enabled on port [chars]Explanation CDP was enabled on a given port. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
Error Message CDP-6-PORTUP: A CDP enabled port [chars] came up.Explanation A CDP enabled port became operational. [chars] is the interface-ID string that identifies the port.
Recommended Action No action is required.
CERT_ENROLL Messages
This section contains the CERT_ENROLL messages.
CERT_ENROLL-2
Error Message CERT_ENROLL-2-CERT_EN_PROGRAM_EXIT: cert_enroll daemon exiting: [chars]Explanation The CERT_ENROLL daemon is exiting.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CERT_ENROLL-3
Error Message CERT_ENROLL-3-CERT_EN_ERROR_MESSAGE: [chars]Explanation This message indicates that a CERT_ENROLL error has occurred.
Recommended Action No action is required.
Error Message CERT_ENROLL-3-CERT_EN_FIPS_MODE_INIT_ERROR: Could not initialize FIPS mode : [chars]Explanation This message indicates that a FIPS mode error has occurred.
Recommended Action No action is required.
CERT_ENROLL-6
Error Message CERT_ENROLL-6-CERT_EN_MESSAGE: [chars]Explanation This message indicates that a CERT_ENROLL error has occurred.
Recommended Action No action is required.
CFS Messages
This section contains the CFS messages.
CFS-2
Error Message CFS-2-CFS_REJECT: CFS reject: [chars]: Switch WWN [chars], ip [chars], reason [chars]Explanation This message indicates that the CFS process was rejected: [chars] Switch WWN [chars], ip [chars], reason [chars].
Recommended Action No action is required.
Error Message CFS-2-EXITING: Exit reason: [chars]Explanation The CFS service process has exited due to [char]. The process has probably been restarted automatically.
Recommended Action No action is required.
Error Message CFS-2-GENERAL_ERROR: [chars]Explanation The CFS service has encountered a critical error. The description of the error is [str.].
Recommended Action No action is required.
Error Message CFS-2-INITFAIL: CFS Service Init failed: [chars]Explanation CFS Service initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message CFS-2-LOCK_FAILED: lock failed for sap [dec] due to internal error.Explanation Lock failed due to Unrestricted uncoordinated count is out of synchronizationfor sap [dec].
Recommended Action To recover from this state run command 'cfs internal decrement-unrestricted <app-sap>'.
Error Message CFS-2-MALLOC_ERROR: Size [dec] bytesExplanation The CFS service could not allocate enough memory.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message CFS-2-MTS_REJECT: Verification failed reject MTS message SAP [dec]:RR-token [hex]Explanation This MTS message could have been posted by the previous active running pre 3.x; MTS structure has changed since then therefore ignore the MTS message, Source SAP [dec]; RR-token [hex].
Recommended Action No action is required.
Error Message CFS-2-PSS_ERROR: [chars]: PSS ret. val=[dec]Explanation The CFS service encountered an error while operating on a persistent storage database.
Recommended Action No action is required.
Error Message CFS-2-VDC_MGR_FAIL: Failed to get a valid switch mac from VDC Manager: [chars]Explanation VDC manager did not respond with a proper MAC address. It could have been because of a timeout in MTS received.
Recommended Action No action is required.
CFS-3
Error Message CFS-3-ALLOCFAIL: Heap Memory allocation failed: [chars]Explanation CFS Service is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-APP_MERGE_FAILED: Merge failed for app [chars], local switch wwn [chars], remote switch wwn [chars].Please check 'show cfs merge status name [chars]' for more informationExplanation The CFS service has detected a merge failure.
Recommended Action No action is required.
Error Message CFS-3-CFS_PSS_CORRUPTED: [chars] PSS found corruptedExplanation The CFS service has detected a corrupted file in its persistent information databases The database would be recreated.
Recommended Action No action is required.
Error Message CFS-3-DBERROR: [chars]Explanation CFS Service encountered a database error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-FAILURE_RESPONSE: [chars] [hex]Explanation CFS Service failed to get response [chars][hex] specify the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-FIPS_TEST_FAILED: FIPS compliance test failedExplanation FIPS compliance test failed.
Recommended Action No action is required.
Error Message CFS-3-GENERROR: [chars]Explanation CFS Service encountered a generalerror thatdoes not fall in any of the above categories. [chars] describes the error and its context.
Recommended Action No action is required.
Error Message CFS-3-LICERR: [chars]Explanation CFS Service failed to get license.
Recommended Action No action is required.
Error Message CFS-3-MERGE_FAILED: Merge failed for app [chars], local switch wwn [chars],ip [chars], remote switch wwn [chars], ip [chars]Explanation The CFS service has detected a merge failure.
Recommended Action No action is required.
Error Message CFS-3-MTSERROR: [chars]Explanation CFS Service encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message CFS-3-PSSERROR: [chars]Explanation CFS Service encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-TIMEOUT_ERROR: [chars] [hex]Explanation CFS Service encountered a timeout [chars][hex] specify the context where the failure occurred.
Recommended Action No action is required.
Error Message CFS-3-UNKNOWN_MSG: Recvd. from Node=[dec] SAP=[dec]Explanation The CFS service has received an unknown message from [dec]].[dec]. This information is for debugging only.
Recommended Action No action is required.
CFS-4
Error Message CFS-4-LICEXP: [chars]Explanation CFS Service license is going to expire. [chars] gives the expected time of expiry.
Recommended Action No action is required.
Error Message CFS-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec]Explanation There was a version mismatch between the CFS service and one of its persistent storage databases. The persistent information has been translated to the new format.
Recommended Action No action is required.
CFS-6
Error Message CFS-6-BECAME_ACTIVE: Became ACTIVE from standby modeExplanation The CFS service on the standby supervisor became active and it is ready to serve client requests.
Recommended Action No action is required.
Error Message CFS-6-BECAME_STDBY: Became STANDBY from active modeExplanation The CFS service became standby from active mode.
Recommended Action No action is required.
Error Message CFS-6-EXCESSIVE_DELAY: [chars]Explanation Excessive time taken for a processing event. The description of the event is [str.].
Recommended Action No action is required.
Error Message CFS-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]Explanation The CFS service was unable to send heartbeats to the system manager.
Recommended Action No action is required.
Error Message CFS-6-GENERAL_EVENT: [chars]Explanation The CFS service has generated an important event. The description of the event is [str.].
Recommended Action No action is required.
Error Message CFS-6-INVALID_CHECKSUM: Received packet from peer on if-index([hex]) with corrupted checksumExplanation This could be because of the errors in the link.
Recommended Action No action is required.
Error Message CFS-6-INVALID_IF_INDEX: Received packet on if-index([hex]) which is not recognized by CFSExplanation The if-index does not match with the if-index used in discovery orthe systemmight have already received an adjacency cleanup message for this if-index. Check if the if-index is that of the port channel or a physical if-index.
Recommended Action No action is required.
Error Message CFS-6-LOGICAL_DISTRIBUTION_INFO: vsan [dec], source wwn [chars], ip [chars] app-id [dec], session-id [dec], user [chars], [chars]Explanation VSAN [dec], source wwn [chars], ip [chars], app-id [dec], user [chars], event [chars].
Recommended Action No action is required.
Error Message CFS-6-PHY_DISTRIBUTION_INFO: source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], [chars]Explanation Source wwn [chars], ip [chars], app-id [dec], session-id [dec], user [chars], event [chars].
Recommended Action No action is required.
Error Message CFS-6-PSS_CREATED: [chars] PSS CreatedExplanation One of the persistent information database of CFS service has been recreated.
Recommended Action No action is required.
Error Message CFS-6-PSS_DESTROYED: [chars] PSS DestroyedExplanation One of the persistent information databases of CFS Service has been intentionally destroyed and would be recreated.
Recommended Action No action is required.
Error Message CFS-6-REGION_CTX_REMOVED: Region info is deleted for [chars]Explanation [chars] is in logical scope. Regions support only physical scope applications.
Recommended Action No action is required.
Error Message CFS-6-SERVICE_UP: Initialized [chars]Explanation The CFS service is up and ready to accept client requests The service was initialized in [char] mode.
Recommended Action No action is required.
Error Message CFS-6-SRVCREATED: CFS Service createdExplanation CFS Service was created successfully and is up and running.
Recommended Action No action is required.
Error Message CFS-6-SRVEXIT: CFS Service shutting down gracefullyExplanation CFS Service is shutting down gracefully.
Recommended Action No action is required.
Error Message CFS-6-SWITCHOVER: Switching Over to other Sup.Explanation The CFS service has successfully switched over to the standby supervisor module.
Recommended Action No action is required.
CIMSRVPROV Messages
This section contains the CIMSRVPROV messages.
CIMSRVPROV-2
Error Message CIMSRVPROV-2-CIM_SYSLOG_EXIT: Message:[chars] errcode:[dec]Explanation Exit due to critical error.
Recommended Action No action is required.
Error Message CIMSRVPROV-2-CIM_SYSLOG_PSS_SNAPSHOT_ERR: Source URI:[chars] Destination URI:[chars] errcode:[dec]Explanation PSS snapshot error.
Recommended Action No action is required.
Error Message CIMSRVPROV-2-CIM_SYSLOG_SDWRAP_ERR: Description:[chars] errcode:[dec]Explanation Debug infrastructure error.
Recommended Action No action is required.
CIMSRVPROV-3
Error Message CIMSRVPROV-3-CIM_SYSLOG_COPY_CONFIG_ERR: Message:[chars] URI:[chars] errcode:[dec]Explanation Copy running startup error.
Recommended Action No action is required.
Error Message CIMSRVPROV-3-CIM_SYSLOG_FILE_ERR: Purpose:[chars] Filename:[chars] errcode:[dec]Explanation File handling error.
Recommended Action No action is required.
Error Message CIMSRVPROV-3-CIM_SYSLOG_MTS_ERR: message [chars]Explanation MTS message handling error.
Recommended Action No action is required.
Error Message CIMSRVPROV-3-CIM_SYSLOG_PSS_ERR: Purpose:[chars] URI:[chars] errcode:[dec]Explanation PSS handling error.
Recommended Action No action is required.
CIMSRVPROV-6
Error Message CIMSRVPROV-6-LOG_CIM_CERTIFICATE_CLEARED: Cleared certificate [chars]Explanation Cleared a certificate named [chars].
Recommended Action No action is required.
Error Message CIMSRVPROV-6-LOG_CIM_CERTIFICATE_INSTALLED: Installed certificate [chars]Explanation Installed a certificate named [chars].
Recommended Action No action is required.
CLIS Messages
This section contains the CLIS messages.
CLIS-5
Error Message CLIS-5-CLIS_SYSLOG_CMD_REMOVED: Command deleted from the NVDB: [chars]Explanation Command removal due to configuration change.
Recommended Action No action is required.
CLOUD Messages
This section contains the CLOUD messages.
CLOUD-2
Error Message CLOUD-2-PROGRAM_EXIT: cloud-discovery process ending: [chars]Explanation Cloud-discovery process is exiting with the reason [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
CLOUD-3
Error Message CLOUD-3-CLOUD_CFS_MERGE_OPERATION_FAILED: [chars]Explanation [chars1].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CLOUD-3-CLOUD_CFS_OPERATION_FAILED: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for the failure of the CFS operation and fix the problem.
Error Message CLOUD-3-CLOUD_FEATURE_MANAGER_ERROR: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for error using feature manager and fix the problem.
Error Message CLOUD-3-CLOUD_PSS_OPERATION_FAILED: [chars] : [chars]Explanation [chars1] [chars2].
Recommended Action Check the reason for the failure of the pss operation and fix the problem.
CLOUD-6
Error Message CLOUD-6-CLOUD_DISCOVERY_DONE: discovery overExplanation Cloud-discovery started.
Recommended Action Check cloud membership.
Error Message CLOUD-6-CLOUD_DISCOVERY_STARTED: [chars] discovery startedExplanation Cloud-discovery started.
Recommended Action Check cloud-discovery status after sometime.
CLUSTER Messages
This section contains the CLUSTER messages.
CLUSTER-2
Error Message CLUSTER-2-CLUSTER_CAP_ADD_FAIL: Failed to add cluster capability [dec]Explanation Cluster capability addition failed.
Recommended Action No action is required.
Error Message CLUSTER-2-CLUSTER_CAP_DEL_FAIL: Failed to delete cluster capability [dec]Explanation Cluster capability deletion failed.
Recommended Action No action is required.
CMPPROXY Messages
This section contains the CMPPROXY messages.
CMPPROXY-2
Error Message CMPPROXY-2-LOG_CMP_IS_NOT_UP: Connectivity Management processor (on module [dec]) did not come upExplanation Connectivity Management processor is not sending heartbeats on this module.
Recommended Action No action is required.
Error Message CMPPROXY-2-LOG_CMP_UP: Connectivity Management processor(on module [dec]) is now UPExplanation Connectivity Management processor has come up and is exchanging heartbeats with CP on this supervisor slot.
Recommended Action No action is required.
Error Message CMPPROXY-2-LOG_CMP_WENT_DOWN: Connectivity Management processor (on module [dec]) went DOWNExplanation Connectivity Management processor has either gone down or is not sending heartbeats for a long time.
Recommended Action No action is required.
CMPPROXY-5
Error Message CMPPROXY-5-LOG_CMP_AAA_FAILURE: Authentication failed for a login from CMP (on module [dec])Explanation A login attempt has been denied access from Connectivity management processor (CMP) as authentication did not succeed.
Recommended Action No action is required.
Error Message CMPPROXY-5-LOG_CMP_UP: Connectivity Management processor(on module [dec]) is now UPExplanation Connectivity Management processor has come up and is exchanging heartbeats with CP on this supervisor slot.
Recommended Action No action is required.
Error Message CMPPROXY-5-MALLOC_FAILURE: Memory allocation failureExplanation Memory allocation in a call to malloc/calloc has failed.
Recommended Action No action is required.
CMPPROXY-6
Error Message CMPPROXY-6-LOG_CMP_AAA_SUCCESS: Authentication succeeded for a login from CMP (on module [dec])Explanation A login attempt has succeeded from Connectivity management processor (CMP) in getting access as AAA succeeded.
Recommended Action No action is required.
COPP Messages
This section contains the COPP messages.
COPP-2
Error Message COPP-2-COPP_INIT_FAIL: CoPP Initialization failed: [chars]Explanation CoPP Initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-2-COPP_MTS_FAIL: Failed to do MTS operation: [chars]Explanation The system has failed to do an MTS operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
COPP-3
Error Message COPP-3-COPP_ALLOC_FAIL: Failed to alloc required memory: [chars]Explanation Failed to allocate required memory. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_ALLOC_FAIL: Memory allocation failure: [chars]Explanation Failed to allocate required memory. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_PPF_FAIL: Error during PPF operation: [chars]Explanation The system has failed to do a PPF operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_PPF_FAIL: Failed to do PPF operation: [chars]Explanation The system has failed to do a PPF operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_PSS_FAIL: Error during PSS operation: [chars]Explanation The system has failed to do a PSS operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message COPP-3-COPP_PSS_FAIL: Failed to do PSS operation: [chars]Explanation The system has failed to do a PSS operation. [chars] explains the reason for the failure.
Recommended Action No action is required.
COPP-5
Error Message COPP-5-COPP_DISABLED: COPP DisabledExplanation COPP Service Disabled.
Recommended Action No action is required.
Error Message COPP-5-COPP_ENABLED: COPP EnabledExplanation COPP Service nabled.
Recommended Action No action is required.
Error Message COPP-5-COPP_INIT: COPP initializedExplanation COPP Service Initialized.
Recommended Action No action is required.
COPP-6
Error Message COPP-6-COPP_POLICY_ATTACHED: CoPP policy has been attached to control plane interface.Explanation CoPP policy has been attached to control plane interface.
Recommended Action No action is required.
Error Message COPP-6-COPP_POLICY_DETACHED: CoPP policy has been detached from control plane interface.Explanation CoPP policy has been detached from control plane interface.
Recommended Action No action is required.
CORE-DMON Messages
This section contains the CORE-DMON messages.
CORE-DMON-2
Error Message CORE-DMON-2-MODULE_COREDUMP_DONE: kernel coredump completed on module:[dec]Explanation Kernel coredump finishing on a module.
Recommended Action No action is required.
Error Message CORE-DMON-2-MODULE_COREDUMP_STARTED: kernel coredump started on module:[dec]Explanation Kernel coredump starting on a module.
Recommended Action No action is required.
CORE-DMON-3
Error Message CORE-DMON-3-NO_SPACE: Failed to save core file [chars]. Try removing existing core files.Explanation Not enough space to save new core files.
Recommended Action No action is required.
CREDITMON-SLOT# Messages
This section contains the CREDITMON-SLOT# messages.
CREDITMON-SLOT#-2
Error Message CREDITMON-SLOT#-2-SYSERR_CREDITMON_APP_EXITED: [chars]Explanation Credit Monitor application exited.
Recommended Action No action is required.
Error Message CREDITMON-SLOT#-2-SYSERR_CREDITMON_MTS_INIT_ERR: [chars]Explanation Credit Monitor error binding to MTS.
Recommended Action No action is required.
CTS Messages
This section contains the CTS messages.
CTS-2
Error Message CTS-2-CTS_AUTHENT_FAILURE: CTS Authentication failure on Port [chars] (CTS Failure Reason: [chars] [chars])Explanation Fibre-Channel Authentication failure on Port [chars].(Reason Code [chars] Detail [chars]). Check password configurations and ensure appropriate security modes on this port as well as peer port.
Recommended Action No action is required.
Error Message CTS-2-DBG_INIT_FAILED: Debug Infrastructure Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-FC2_E_INIT_FAILED: Fibre-Channel Initialization of an E_Port failed ( [chars] )Explanation CTS Manager has been unable to initialize with the FC-2 E-Port infrastructure.
Recommended Action No action is required.
Error Message CTS-2-FC2_F_INIT_FAILED: Fibre-Channel Initialization of an F_Port failed ( [chars] )Explanation CTS Manager has been unable to initialize with the FC-2 F-Port infrastructure.
Recommended Action No action is required.
Error Message CTS-2-FC2_UNKNOWN_FRM_RECD_CRIT: Received an unexpected/unknown FC-2 frame on [chars]Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-FSMU_INIT_FAILED: State Machine Infrastructure Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-IPC_INIT_FAILED: IPC (Inter Process Communication) Initialization failed ( [chars] )Explanation CTS Manager has been unable to initialize with the IPC infrastructure.
Recommended Action No action is required.
Error Message CTS-2-LICENSE_UNAVAILABLE: License:[chars] unavailable, service exitingExplanation License of [chars] is unavailable. Service will exit now.
Recommended Action Install the license file to continue using the feature.
Error Message CTS-2-MEM_FAILED: Memory operations failed File: [chars] Line [dec] for size [hex] bytesExplanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-POST_INIT_FAILED: Post-Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-PSS_INIT_FAILED: PSS Infrastructure Initialization failed ( [chars] )Explanation The system has detected an error.
Recommended Action No action is required.
Error Message CTS-2-RBACL_UNABLE_PARSE_ACE: Unable to parse RBACL ACE substring: [chars]Explanation The system has detected an error.
Recommended Action No action is required.
CTS-3
Error Message CTS-3-DOT1X_AUTHC_FAILED: DOT1X authentication failed on port: [chars]Explanation DOT1X authentication failed on the port.
Recommended Action No action is required.
DEBUGPROXY Messages
This section contains the DEBUGPROXY messages.
DEBUGPROXY-6
Error Message DEBUGPROXY-6-SSM_DEBUG_PROXY_COMMON: SSM debug proxy [chars] [dec]Explanation General SSM debug proxy information.
Recommended Action No action is required.
DEV_LOG Messages
This section contains the DEV_LOG messages.
DEV_LOG-3
Error Message DEV_LOG-3-ERROR: [chars]Explanation Dev_log_lc encountered an error.
Recommended Action No action is required.
DEVICE-ALIAS Messages
This section contains the DEVICE-ALIAS messages.
DEVICE-ALIAS-2
Error Message DEVICE-ALIAS-2-ALLOC_FAILED: Memory allocation failed for size:[dec] type:[dec]Explanation Memory allocation failed for size [dec] type [dec].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-2-INIT_FAILED: [chars]Explanation An error occurred during initialization. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE-ALIAS-3
Error Message DEVICE-ALIAS-3-CFS_OPER_FAILED: [chars]Explanation An error occurred while performing a CFS operation. [chars] indicates the CFS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-CLEAR_FAILED: [chars]Explanation An error occurred while clearing the session. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-COMMIT_FAILED: [chars]Explanation An error occurred while committing the database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-COMMIT_REJECTED: [chars]Explanation Commit request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-LOCK_FAILED: [chars]Explanation An error occurred while acquiring the lock. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-LOCK_REJECTED: [chars]Explanation Lock request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_ACTIVATION_FAILED: [chars]Explanation An error occurred while activating the merged database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_ACTIVATION_REJECTED: [chars]Explanation Merge activation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_FAILED: [chars]Explanation An error occurred during merge operation. [chars] indicates the reason for failure.
Recommended Action Compare device-alias configuration with the other switches in the fabric, resolve the conflicts if any and commit the changes.
Error Message DEVICE-ALIAS-3-MERGE_MREQ_REJECTED: [chars]Explanation MREQ received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_MRESP_REJECTED: [chars]Explanation MRESP received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_VALIDATION_FAILED: [chars]Explanation An error occurred while validating the merged database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MERGE_VALIDATION_REJECTED: [chars]Explanation Merge validation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-MTS_OPER_FAILED: [chars]Explanation An error occurred during MTS operation. [chars] indicates the MTS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-PSS_OPER_FAILED: [chars]Explanation An error occurred during PSS operation. [chars] indicates the PSS operation and the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-UNLOCK_FAILED: [chars]Explanation An error occurred while releasing the lock. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-UNLOCK_REJECTED: [chars]Explanation Unlock request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-VALIDATION_FAILED: [chars]Explanation An error occurred while validating the database. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-3-VALIDATION_REJECTED: [chars]Explanation Validation request received from remote switch is rejected. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE-ALIAS-6
Error Message DEVICE-ALIAS-6-CLEAR_FAILED_INFO: [chars]Explanation An error occurred while clearing the session. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-COMMIT_FAILED_INFO: [chars]Explanation An error occurred while committing the database. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-IMPORT_DEFINITION_CONFLICT: Fcalias [chars] could not be imported due to definition conflictExplanation Fcalias [chars] could not be imported due to definition conflict. Either there is already a device-alias configuration present with the same definition OR another VSAN specified in the import VSAN range has an fcalias with the same definition.
Recommended Action Resolve the conflict and issue the import command again.
Error Message DEVICE-ALIAS-6-IMPORT_MEMBER_TYPE_CONFLICT: Fcalias [chars] could not be imported due to having unsupported member typeExplanation Fcalias [chars] could not be imported due to having unsupported member types. Fcalias can be imported only if it has Port WWN based members.
Recommended Action Make sure that the fcalias has Port WWN based members and issue the import command again.
Error Message DEVICE-ALIAS-6-IMPORT_NAME_CONFLICT: Fcalias [chars] could not be imported due to name conflictExplanation Fcalias [chars] could not be imported due to name conflict. Either there is already a device-alias configuration present with the same name OR another VSAN specified in the import VSAN range has an fcalias with the same name.
Recommended Action Resolve the conflict and issue the import command again.
Error Message DEVICE-ALIAS-6-IMPORT_NUM_MEMBERS_CONFLICT: Fcalias [chars] could not be imported due to having unsupported number of membersExplanation Fcalias [chars] could not be imported due to having unsupported number of members. Fcalias can be imported only if it has exactly one member.
Recommended Action Make sure that the fcalias has exactly one member and issue the import command again.
Error Message DEVICE-ALIAS-6-LOCK_FAILED_INFO: [chars]Explanation An error occurred while acquiring the lock. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-MERGE_ACTIVATION_FAILED_INFO: [chars]Explanation An error occurred while activating the merged database. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-MERGE_VALIDATION_FAILED_BUSY: [chars]Explanation Merged database could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-MERGE_VALIDATION_REJECTED_BUSY: [chars]Explanation Merged database received from the remote switch could not be validated as some of the applications are busy. [chars] indicates information about the application returned busy. There is no user intervention necessary. The validation would be automatically retried after some time.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-UNLOCK_FAILED_INFO: [chars]Explanation An error occurred while releasing the lock. [chars] indicates the additional information regarding failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DEVICE-ALIAS-6-VALIDATION_ABORTED: [chars]Explanation Local validation is aborted. [chars] indicates the reason why validation is aborted.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DEVICE_TEST Messages
This section contains the DEVICE_TEST messages.
DEVICE_TEST-2
Error Message DEVICE_TEST-2-ASIC_REG_CHECK_FAIL: Module [dec] has failed test [chars] [dec] times on device [chars] instance [dec] frontpanel ports affected [chars] due to error [chars]Explanation The online diagnostic ASICRegisterCheck test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-COMPACT_FLASH_FAIL: Module [dec] has failed test [chars] [dec] times on device Compact Flash due to error [chars]Explanation The online diagnostic CompactFlash test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-CRYPTO_DEVICE_FAIL: Module [dec] has failed test [chars] [dec] times on Crypto device due to error [chars]Explanation The online diagnostic CryptoDevice test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-FAN_MOD_FAIL: Module [dec] has failed test [chars] [dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error [chars] error number [hex]Explanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-MALLOC_FAILURE: Memory allocation failedExplanation Device Test process could not allocate enough memory.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-NVRAM_FAIL: Module [dec] has failed test [chars] [dec] times on device NVRAM due to error [chars]Explanation The online diagnostic NVRAM test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-POWER_SUPPLY_FAIL: Module [dec] has failed test [chars] [dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error [chars] error number [hex]Explanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-PRIMARY_BOOTROM_FAIL: Module [dec] has failed test [chars] [dec] times on device Primary BootROM due to error [chars]Explanation The online diagnostic PrimaryBootROM test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module [dec] has failed test [chars] [dec] times on device Power Mgmt Bus on slot [dec] due to error [chars] error number [hex]Explanation The online diagnostic PwrMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-RTC_FAIL: Module [dec] has failed test [chars] [dec] times on device RealTimeClock due to error [chars]Explanation The online diagnostic RealTimeClock test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-SECONDARY_BOOTROM_FAIL: Module [dec] has failed test [chars] [dec] times on device Secondary BootROM due to error [chars]Explanation The online diagnostic SecondaryBootROM test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-SPINE_CONTROL_BUS_FAIL: Module [dec] has failed test [chars] [dec] times on device Spine Control Bus on slot [dec] due to error [chars] error number [hex]Explanation The online diagnostic SpineControlBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-SYSTEM_MGMT_BUS_FAIL: Module [dec] has failed test [chars] [dec] times on System Mgmt Bus for chassis [chars] instance [dec] due to error [chars] error number [hex]Explanation The online diagnostic The systemMgmtBus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-TWOWIRE_STW_FAIL: Module [dec] has failed test [chars] [dec] times on Status Bus on slot [dec] due to error [chars]Explanation The online diagnostic Status bus test has failed.
Recommended Action No action is required.
Error Message DEVICE_TEST-2-USB_FAIL: Module [dec] has failed test [chars] [dec] times on device USB due to error [chars]Explanation The online diagnostic USB test has failed.
Recommended Action No action is required.
DEVICE_TEST-4
Error Message DEVICE_TEST-4-THREAD_CREATE_FAIL: Thread creation failedExplanation Device Test process could not create threads.
Recommended Action No action is required.
Error Message DEVICE_TEST-4-TIMER_CREATE_FAIL: Timer creation failedExplanation Device Test process could not create timer.
Recommended Action No action is required.
Error Message DEVICE_TEST-4-TIMER_START_FAIL: Timer start failedExplanation Device Test process could not start timer.
Recommended Action No action is required.
DEVICE_TEST-5
Error Message DEVICE_TEST-5-NOTICE_TEST: Memory allocation failed noticeExplanation Device Test process could not allocate enough memory.
Recommended Action No action is required.
DEVICE_TEST-6
Error Message DEVICE_TEST-6-INFO_TEST: Memory allocation failed infoExplanation Device Test process could not allocate enough memory.
Recommended Action No action is required.
DFTM Messages
This section contains the DFTM messages.
DFTM-3
Error Message DFTM-3-DFTM_BDDB_PROG_FAILED: DFTM failed to program BDDB Entry: [chars]Explanation DFTM failed to program BDDB Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_BDT_PROG_FAILED: DFTM failed to program BD Table Entry: [chars]Explanation DFTM failed to program BD Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_L2L3CT_PROG_FAILED: DFTM failed to program L2L3 Consistency Table Entry: [chars]Explanation DFTM failed to program L2L3 Consistency Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_MFT_PROG_FAILED: DFTM failed to program Multicast FTag Table Entry: [chars]Explanation DFTM failed to program Multicast Ftag Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_SDT_PROG_FAILED: DFTM failed to program SGT DGT Table Entry: [chars]Explanation DFTM failed to program SGT DGT Table Entry.
Recommended Action No action is required.
Error Message DFTM-3-DFTM_VTT_PROG_FAILED: DFTM failed to program VLAN Translation Table Entry: [chars]Explanation DFTM failed to program VLAN Translation Table.
Recommended Action No action is required.
DHCP_SNOOP Messages
This section contains the DHCP_SNOOP messages.
DHCP_SNOOP-2
Error Message DHCP_SNOOP-2-HWPGMFAILURE: Hardware programming has failed: [chars]Explanation Hardware programming has failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-2-INITFAIL: DHCP Daemon Initialization failed: [chars]Explanation DHCP daemon initialization failed. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-2-PSSERROR: [chars]Explanation DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-2-REGPARTREE: Unable to register par tree: [chars]Explanation Could not register par tree. [chars] explains the reason for the failure.
Recommended Action No action is required.
DHCP_SNOOP-3
Error Message DHCP_SNOOP-3-ALLOCFAIL: Heap Memory allocation failed: [chars]Explanation DHCP Daemon is out of dynamic memory. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-DHCPDENIEDARP: ARP frame denied due to DHCP snooping binding on interface [chars] vlan [dec] sender mac [chars] sender ip [chars] target mac [chars] target ip [chars].Explanation [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been denied. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-DHCPRATELIMIT: Interface [chars] has been error disabled due to excessive ingress rate [dec] of DHCP packets.Explanation [chars] identifies the interface which has been error disabled due to excessive ingress rate [dec].
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-INVDHCPPKTS: [dec] invalid DHCP packets received on interface [chars] vlan [dec]Explanation [dec] identifies the number of invalid packets. [chars] identifies the interface and [dec] identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-MTSERROR: [chars]Explanation The CDP daemon encountered an MTS error. [chars] specifies the context where the error occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-PKTRECVFAIL: Failed to receive packet - [chars]Explanation The system has failed to receive the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-PKTSENDFAIL: Failed to send packet, - [chars]Explanation The system has failed to send the packet. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-PSSERROR: [chars]Explanation DHCP Daemon encountered a PSS error. [chars] specifies the context where the failure occurred.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-SOCKBINDFAIL: Failed to bind to raw socket - [chars]Explanation Failed to bind to socket. [char] identifies the reason.
Recommended Action No action is required.
Error Message DHCP_SNOOP-3-SOCKOPENFAIL: Failed to open socket for receiving DHCP packets - [chars]Explanation An attempt to open a socket for receiving DHCP packets failed. [char] identifies the reason.
Recommended Action No action is required.
DHCP_SNOOP-4
Error Message DHCP_SNOOP-4-ACL_DENY: [dec] Invalid ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-ACL_PERMIT: [dec] ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-DHCP_SNOOPING_DENY: [dec] Invalid ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-DHCP_SNOOPING_PERMIT: [dec] ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-ERROR_DISABLED: Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packetsExplanation Interface [chars] has moved to error disabled state due to excessive rate [dec] of ingress ARP packets.
Recommended Action No action is required.
Error Message DHCP_SNOOP-4-INVALID_ARP: [dec] Invalid ARP messages ([chars]) on [chars], vlan [dec]. ([[chars]/[chars]/[chars]/[chars]/[chars]])Explanation Packet-count [dec] Invalid ARPs (arp-type [chars]) on interface [chars], vlan [dec]. ([sender-mac [chars]/sender-ip [chars]/ target-mac [chars]/target-ip [chars]/ time-of-day [chars]]).
Recommended Action No action is required.
DHCP_SNOOP-6
Error Message DHCP_SNOOP-6-DAIVLANDISABLE: DAI disabled on vlan [dec]Explanation Dynamic ARP Inspection was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DAIVLANENABLE: DAI enabled on vlan [dec]Explanation Dynamic ARP Inspection was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPEXIT: DHCP Daemon shutting down gracefully.Explanation DHCP Daemon is shutting down gracefully.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPHOSTADD: A new Host is [chars] connected to interface [chars] in VLAN [dec] and is allocated IP address [chars] for [dec] secs.Explanation A Host identified by [chars] has been added. [chars] identifies the interface. [dec] identifies the VLAN. [chars] identifies IP address. [dec] identifies the lease time in secs.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPLEASEEXPIRE: Lease expired for host [chars] having IP address [chars] connected to interface [chars] in VLAN [dec] for lease [dec] secs.Explanation The lease for host identified by [chars] with IP address [chars] connected to interface [chars] in VLAN [dec] with lease [dec] has expired.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPPERMITTEDARP: ARP frame permitted due to DHCP snooping binding on interface [chars] vlan [dec] sender mac [chars] sender ip [chars] target mac [chars] target ip [chars].Explanation [chars] identifies interface and [dec] identifies the vlan on which ARP packets have been permitted. [chars] identifies sender mac and [chars] identifies the sender ip. [chars] identifies the target mac and [chars] identifies the target ip.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-DHCPUP: DHCP Daemon Up.Explanation DHCP Daemon was created successfully and is up and running.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-INFO: [chars]Explanation An event during switchover. [chars] explains the reason for the failure.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-INTFDISABLE: IP Src Guard disabled on intf [chars]Explanation IP Src Guard was disabled on a given intf. [chars] is the intf-ID string that identifies the intf.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-INTFENABLE: IP Src Guard enabled on intf [chars]Explanation IP Src Guard was enabled on a given intf. [chars] is the intf-ID string that identifies the intf.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-VLANDISABLE: DHCP Snooping disabled on vlan [dec]Explanation DHCP Snooping was disabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
Error Message DHCP_SNOOP-6-VLANENABLE: DHCP Snooping enabled on vlan [dec]Explanation DHCP Snooping was enabled on a given vlan. [dec] is the VLAN-ID that identifies the vlan.
Recommended Action No action is required.
DIAG_PORT_LB Messages
This section contains the DIAG_PORT_LB messages.
DIAG_PORT_LB-2
Error Message DIAG_PORT_LB-2-DIAG_FWD_PATH_SETUP_FAILURE: [chars]. Module:[dec] Error:[chars].Explanation Forwarding path setup for port loopback tests failed.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-GET_DIAG_BD_FAIL: [chars]([dec]) Failed to get the BD for Diag VLAN:[dec]. Error:[chars].Explanation Failed to get the BD corresponding to the Diag VLAN.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-LCM_RESP_SEND_FAILURE: LC Inserted request response send to Module Manager failed . Error:[chars]Explanation Failed to send the response for LC insertion to Module Manager.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-LIF_GET_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed to get Diagnostic LIF id.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-MALLOC_FAILURE: [chars]([dec]) Memory allocation failed.Explanation Port Loopback test process could not allocate enough memory.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-MTS_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in MTS API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-PROC_INIT_FAILURE: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed in process initialization.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-2-VLAN_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed to get Diagnostic VLAN information.
Recommended Action No action is required.
DIAG_PORT_LB-3
Error Message DIAG_PORT_LB-3-DIAG_FWD_PATH_SETUP_FAILURE: [chars]. Module:[dec] Error:[chars].Explanation Forwarding path setup for port loopback tests failed.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-DIAG_PKT_SEND_FAILURE: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed to send loopback packets.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-FSM_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in MTS API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-GET_DIAG_BD_FAIL: [chars]([dec]) Failed to get the BD for Diag VLAN:[dec]. Error:[chars].Explanation Failed to get the BD corresponding to the Diag VLAN.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-IFINDEX_LIB_FAILURE: [chars]([dec]) [chars] [chars]:[hex] [chars] [chars]Explanation Port Loopback test process failed in if_index library API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-INVALID_TEST_REQUEST: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed to get test request info.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-INVALID_TEST_RUN: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed to get the current test run information.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-LIF_GET_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed to get Diagnostic LIF id.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-MALLOC_FAILURE: [chars]([dec]) Memory allocation failed.Explanation Port Loopback test process could not allocate enough memory.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-MTS_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in MTS API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PDB_LIB_API_ERROR: Failed to [chars]. Error:[dec].Explanation The port loopback test was not able to get chassis information.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PIXM_LIB_ERROR: [chars]([dec]) Failed to convert [chars]:[hex] to [chars]. Error:[chars]Explanation Port Loopback test process failed to convert port ifindex <-> port index.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PORT_CFG_REQ_SEND: [chars]([dec]) Failed to send request to configure port ifindex:[dec] for port loopback testExplanation Failed to configure/restore the port to do/cleanup port loopback testing.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PORT_CLIENT_LIB_ERROR: [chars]([dec]) [chars]. Error:[chars]Explanation Port Loopback test process failed in Port Client API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PORTLOOPBACK_TEST_FAIL: Module:[dec] Test:PortLoopback failed [dec] consecutive times. Faulty module:[dec] affected ports:[chars] Error:[chars]Explanation PortLoopback test failed on the module consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-PROC_INIT_FAILURE: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed in process initialization.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-RESULT_ADD_FAILURE: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed to add the port test result.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-RESULT_SEND_FAILURE: [chars]([dec]) [chars]Explanation Port Loopback test process failed to send the test results.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-REWRITE_ENGINE_LOOPBACK_TEST_FAIL: Module:[dec] Test:RewriteEngine Loopback failed [dec] consecutive times. Faulty module:[dec] affected ports:[chars] Error:[chars]Explanation Rewrite Engine Loopback test failed on the module consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-RW_ENGINE_LOOPBACK_TEST_SPINE_PATH_FAIL: Module:[dec] Test:RewriteEngine Loopback Spine path:[dec] failed [dec] consecutive times. Error:[chars]Explanation Rewrite Engine Loopback test failed on the spine path consecutively.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-SOCKET_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed in socket operations.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-STATS_LIB_ERROR: [chars]([dec]) [chars]:[dec]Explanation Port Loopback test process failed in stats infra lib API.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-TEST_RES_SEND_FAIL: Failed to send [chars] test results back to Diagnostics Infrastucture. Error:[chars].Explanation The port loopback test was not able to send the test results.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-TIMER_LIB_ERROR: [chars]([dec]) [chars]Explanation Port Loopback test process timer handling failure.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-VLAN_ERROR: [chars]([dec]) [chars] Error:[chars]Explanation Port Loopback test process failed to get Diagnostic VLAN information.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-VQI_GET_FAIL: Failed to get the Diag VQi from XBM. Error:[chars]Explanation Rewrite Engine Loopback test failed to get the Diag VQi from XBAR Mgr.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-3-XBM_CFG_REQ_FAIL: Failed to conigure the XBAR mask while running the RewriteEngineLoopback test. Error:[chars]. Module:[dec] could have gone offlineExplanation Rewrite Engine Loopback test failed to set the XBAR mask while running the test. The target module could have gone offline.
Recommended Action No action is required.
DIAG_PORT_LB-5
Error Message DIAG_PORT_LB-5-DIAG_PORT_LB_DISABLED: DIAG_PORT_LB DisabledExplanation DIAG_PORT_LB Service Disabled.
Recommended Action No action is required.
Error Message DIAG_PORT_LB-5-DIAG_PORT_LB_ENABLED: DIAG_PORT_LB EnabledExplanation DIAG_PORT_LB Service nabled.
Recommended Action No action is required.
DIAGCLIENT Messages
This section contains the DIAGCLIENT messages.
DIAGCLIENT-2
Error Message DIAGCLIENT-2-DIAG_BOOTUP_COMPLETE: Module <[dec]> Bootup Test <[chars]> has reported <[chars]>Explanation Bootup Test completed.
Recommended Action Nothing to be done if the test reports SUCCESS otherwise copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.
Error Message DIAGCLIENT-2-EEM_ACTION_HM_SHUTDOWN: Test <[chars]> has been disabled as a part of default EEM actionExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-2-PSS_READ_FAILURE: Read from PSS failed on Module <[dec]>Explanation Read operation from PSS store failed.
Recommended Action No action is required.
Error Message DIAGCLIENT-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]>Explanation Write operation on PSS store failed.
Recommended Action No action is required.
DIAGCLIENT-3
Error Message DIAGCLIENT-3-DIAG_HM_FAIL: Module <[dec]> Health Monitoring Test <[chars]> has failed. Please use 'show diagnostic result <target>' to see test resultsExplanation A Health Monitoring Test has reported failure.
Recommended Action Ensure the line card is firmly in the slot, reseat if necessary, and attempt to run the test again if the line card is not seated properly in the slot. If the line card was properly seated in the slot, copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.
Error Message DIAGCLIENT-3-ONDEMAND_FAIL_EXCESS: Module <[dec]> Test <[chars]> has failed more than <[dec]> number of timesExplanation Ondemand test has failed more than configured number of times.
Recommended Action Copy the error message exactly as it appears on the console, gather the output of show tech-support, and contact your Cisco technical support representative with the gathered information.
Error Message DIAGCLIENT-3-PER_PORT_TEST_FAIL: Module <[dec]> Test <[chars]> has failed on Ports <[chars]> Please use 'show diagnostic result <target>' to see test resultsExplanation Per Port Test has failed on the above all ports.
Recommended Action No action is required.
DIAGCLIENT-4
Error Message DIAGCLIENT-4-LC_OFFLINE_FOR_CURR_SLOT: Received LC offline event for the current slot:[dec]. Ignoring itExplanation Informational Syslog.
Recommended Action No action is required.
Error Message DIAGCLIENT-4-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], dest slot: [dec], dest SAP: [dec], error-id: [hex]Explanation MTS send reports failure.
Recommended Action No action is required.
DIAGCLIENT-5
Error Message DIAGCLIENT-5-CALLOC_FAILURE: Memory allocation failedExplanation DiagClient process could not allocate enough memory.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-DIAG_SCHED_COMPLETE: Module <[dec]> Test <[chars]> has completed Scheduled TestingExplanation A scheduled Test was completed.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-ONDEMAND_FAIL: Module <[dec]> Test <[chars]> has failed in Test_Iteration <[dec]>Explanation The specified test has reported FAILURE in this Iteration.
Recommended Action No action is required.
Error Message DIAGCLIENT-5-ONDEMAND_SUCCESS: Module <[dec]> Test <[chars]> has completed successfully in Test_Iteration <[dec]>Explanation The specified test has reported SUCCESS in this Iteration.
Recommended Action No action is required.
DIAGMGR Messages
This section contains the DIAGMGR messages.
DIAGMGR-2
Error Message DIAGMGR-2-MTS_SEND_FAILURE: MTS send failed, mts_opc: [chars], dest slot: [dec], dest SAP: [dec], error-id: [hex]Explanation MTS send reports failure.
Recommended Action No action is required.
Error Message DIAGMGR-2-PSS_DELETE_FAILURE: Read from PSS failed on Module <[dec]>Explanation Read operation from PSS store failed.
Recommended Action No action is required.
Error Message DIAGMGR-2-PSS_WRITE_FAILURE: Write to PSS failed on Module <[dec]>Explanation Write operation on PSS store failed.
Recommended Action No action is required.
DIAGMGR-3
Error Message DIAGMGR-3-DIAG_MAJOR_DEFECT: Module <[dec]> Test <[chars]> detected a Major Error Please use 'show diagnostic result <target>' to see test resultsExplanation A major error was detected during diagnostic testing.
Recommended Action Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.
Error Message DIAGMGR-3-DIAG_MINOR_DEFECT: Module <[dec]> Test <[chars]> detected a Minor Error Please use 'show diagnostic result <target>' to see test resultsExplanation A mior error was detected during diagnostic testing.
Recommended Action Re-seat the card and retry the test. If the same result occurs after reseating the card and retrying the test, copy the error message exactly as it appears on the screen and gather the output of show tech-support and any other relevant information. Contact your technical support representative with the gathered information.
Error Message DIAGMGR-3-GET_CURR_SLOT_FAIL: Failed to get the current slot for the process. Error:[chars]Explanation The process initialization failed to get the current slot.
Recommended Action This is an informational message stating that a process initialization failure.
DIAGMGR-4
Error Message DIAGMGR-4-CURR_SLOT_OFFLINE: Recevied an LC offline event for the current slot:[dec]. Ignoring itExplanation The process received an offline event for the slot it is running. Ignoring it.
Recommended Action This is an informational message stating that an unexpected event has been encountered.
Error Message DIAGMGR-4-DISRPT_TST_START: Starting Test <[chars]> on Module <[dec]> is DisruptiveExplanation Starting a Disruptive Test can disturb the system's normal functionality.
Recommended Action Reset target module.
Error Message DIAGMGR-4-FIXED_INTRVL_CHANGED: The users are not allowed to change monitoring interval of Test <[chars]>Explanation The specified health monitoring test interval is not user-configurable and therefore cannot be changed.
Recommended Action No action is required.The specific health monitoring interval is not user- configurable by design so nothing can be done to change the interval.
DIAGMGR-5
Error Message DIAGMGR-5-BOOTUP_CONF: Diagnostic Bootup Level: <[chars]>Explanation Current Diagnostic BootUp Level being configure or changed.
Recommended Action No action is required.
Error Message DIAGMGR-5-CALLOC_FAILURE: Memory allocation failureExplanation Memory allocation in a call to malloc/calloc has failed.
Recommended Action No action is required.
Error Message DIAGMGR-5-CHANGE_ALWAYS_HM: Health Monitoring test <[chars]> in Module <[dec]> is a must run and cannot be modifiedExplanation The specified health monitoring test must be run and cannot be disabled.
Recommended Action No action is required.The specific health monitoring test cannot be disabled by design. The system is working properly.
Error Message DIAGMGR-5-HM_START: Health monitoring test <[chars]> for Module <[dec]>Explanation Health Monitoring Test started.
Recommended Action No action is required.
Error Message DIAGMGR-5-HM_STOP: Disabling health monitoring test <[chars]> for Module <[dec]>Explanation Health Monitoring Test has been stopped It can be enabled through the diagnostic monitor..... command.
Recommended Action No action is required.
Error Message DIAGMGR-5-INTRVL_INCORRECT: Monitoring Interval is less than minimum of [dec] seconds required for Module <[dec]> test <[chars]>Explanation Health Monitoring cannot be enabled for the specified test because the interval for the test has been incorrectly set.
Recommended Action The system is working properly and no action is required. If you want to specify a smaller testing interval, the error message text provides the lowest possible configurable interval for the specified monitoring interval.
Error Message DIAGMGR-5-MODULE_MISSING: Diagnostic command issued on non-existing Module <[dec]>Explanation A line card could not be located in a slot where a diagnostic action was requested.
Recommended Action Ensure the targeted line card is properly seated in the specified slot. If the line card is properly seated, ensure the correct slot was indicated in the command-line interface. If the line card is well-seated and the correct slot was specified, copy the error message exactly as it appears on the screen as well as the output of show tech-support and paste the output into a separate file. Contact your technical support representative with the gathered information.
Error Message DIAGMGR-5-NONHM_AS_HM: The Test <[chars]> cannot be used as health monitoring testExplanation Non-HM test cannot be scheduled to run as a Health Monitoring test.
Recommended Action No action is required.
DIAGMGR-6
Error Message DIAGMGR-6-BOOTUP_DIAG_OK: Module <[dec]>: Passed Online DiagnosticsExplanation The diagnostic tests did not detect any error on the card.
Recommended Action This is an informational message stating that the line card passed the diagnostic tests.
Error Message DIAGMGR-6-BOOTUP_TEST_STARTED: Module <[dec]>: Running [chars] DiagnosticsExplanation Starting bootup testing for above module.
Recommended Action No action is required.
DMM-SLOT# Messages
This section contains the DMM-SLOT# messages.
DMM-SLOT#-5
Error Message DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_SRVR_ZONE: Job Id:%Ld VSAN :[dec] New N-Port FCID :[hex] Server FCID:[hex] are in the same zone. ALERT!!Explanation A New N-Port has come up which is zoned in the same zone as the Server.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_STG_ZONE: Job Id:%Ld VSAN :[dec] New N-Port FCID :[hex] Storage FCID:[hex] are in the same zone. ALERT!!Explanation A New N-Port has come up which is zoned in the same zone as the Storage.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_ERR_DMM_SRVR_RSCN: Job Id:%Ld Server N-Port pWWN:0x%Lx [chars]Explanation An RSCN event was received for the Server associated with a Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_ERR_DMM_STG_RSCN: Job Id:%Ld N-Port pWWN:0x%Lx Storage:[chars] [chars]Explanation An RSCN event was received for the Storage associated with a Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_COMPLETE: Job Id:%Ld NumSession:[dec]Explanation Event indicating the completion of a Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_ERROR_LOST_SSM_PEER_CONNECTION: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job due to loss in ip connectivity to peer ssm.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_FINISH: Job Id:%Ld NumSession:[dec]Explanation Event indicating Finish-request for a Method-2 Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_START: Job Id:%Ld NumSession:[dec]Explanation Event indicating the start of a Data Migration Job.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_STOP: Job Id:%Ld NumSession:[dec]Explanation Event indicating that the Data Migration Job was stopped by Administrator.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_TCP_CONNECTION_DOWN: Job Id:%Ld lost connection to peer [chars]. Job may be RESETExplanation Event indicating IP Connectivity loss to peer SSM. Affected Job may be RESET.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_COMPLETE: Job Id:%Ld NumSession:[dec]Explanation Event indicating the completion of a Data Migration Job Verification.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_ERROR: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job Verification due to an error.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_START: Job Id:%Ld NumSession:[dec]Explanation Event indicating the start of a Data Migration Job Verification.
Recommended Action No action is required.
Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_VERIFY_STOP: Job Id:%Ld NumSession:[dec]Explanation Event indicating the Suspension of Data Migration Job Verification by the user.
Recommended Action No action is required.
DOT1X Messages
This section contains the DOT1X messages.
DOT1X-2
Error Message DOT1X-2-DOT1X_INIT: Dot1x unable to startExplanation The system failed to create the Dot1x process.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DOT1X-3
Error Message DOT1X-3-ERR_SPANDST: It is configured as a SPAN Dest port.Explanation Dot1x and SPAN Dest ports are mutually exclusive features.
Recommended Action Disable SPAN destination port configuration first before reconfiguring Dot1x on the port.
Error Message DOT1X-3-INVALID_INPUT: Invalid on interface [chars].Explanation The Dot1x interface parameter is out of the specified range or is invalid.
Recommended Action Refer to the CLI help documentation to determine the valid 802.1x parameters.
Error Message DOT1X-3-MEM_UNAVAIL: perform the 802.1X action.Explanation Insufficient system memory is available to perform the Dot1x Authentication.
Recommended Action Reduce other system activity to ease memory demands. If conditions warrant, upgrade to a larger memory configuration.
Error Message DOT1X-3-NOT_DOT1X_CAPABLE: interface [chars] because it is not a physical Ethernet interface.Explanation Dot1x Authentication can only be enabled on physical Ethernet interfaces.
Recommended Action Enable Dot1x Authentication on physical Ethernet interfaces only.
Error Message DOT1X-3-SM_INIT: Internal error while initializing state machine [chars], state [chars]: [chars]Explanation An attempt was made to initialize an invalid state machine.
Recommended Action Initialize dot1x state machine.
DOT1X-4
Error Message DOT1X-4-BADEVENT: Event [chars] is invalid for the current state [chars]: [chars] [chars]Explanation An attempt was made to post an event to a state machine that is invalid for the current state.
Recommended Action Initialize dot1x state machine.
Error Message DOT1X-4-MAB_DISABLED: Interface [chars] is in Trunk mode, MAB is not supported on this portExplanation MAB is not supported on Trunk port.
Recommended Action To enable MAB make sure that port is not in trunk mode.
Error Message DOT1X-4-MAB_DISABLED: Interface [chars] is in Trunk mode, MAB will be disabled on this portExplanation MAB is not supported on Trunk port.
Recommended Action To enable MAB make sure that port is not in trunk mode.
Error Message DOT1X-4-MAB_DISABLED_ON_PCM: Interface [chars] is a member of portchannel, MAB is not supported on this portExplanation MAB is not supported on port channel member port.
Recommended Action To enable MAB make sure that port is not member of port channel.
Error Message DOT1X-4-MULTIHOST_ON_PCM: Interface [chars] is a member of portchannel, dot1x host mode will be multi-host and changing it to single-host mode won't be supportedExplanation Current Port is a member of port channel, so dot1x host mode has to be in multi-host mode.
Recommended Action To change host mode, ensure that port is not a member of port channel.
Error Message DOT1X-4-STOPPED: Event [chars] ignored because the state machine is stopped: [chars] [chars]Explanation An attempt was made to post an event to a state machine that has already been stopped.
Recommended Action An internal error has occurred with the state machine. The traceback should indicate the guilty party.
Error Message DOT1X-4-TO_MULTIHOST: Interface [chars] is in trunk mode, dot1x host mode will be multi-host and changing it to single-host mode won't be supportedExplanation Current Port is in trunk mode, so dot1x host mode has to be in multi-host mode.
Recommended Action To change host mode, ensure that port is not in trunk mode.
DOT1X-5
Error Message DOT1X-5-DOT1X_DISABLED: dot1x DisabledExplanation Dot1x Service Disabled.
Recommended Action No action is required.
Error Message DOT1X-5-DOT1X_ENABLED: dot1x EnabledExplanation Dot1x Service Enabled.
Recommended Action No action is required.
Error Message DOT1X-5-INVALID_MAC: broadcast or multicast mac address) [chars] is trying to authenticate.Explanation Authentication using 802.1x is not allowed for zero, broadcast, and multicast source MAC addresses.
Recommended Action Connect a Dot1x supported Host to the Dot1x enabled port.
Error Message DOT1X-5-SECURITY_VIOLATION: interface [chars], New MAC address [chars] is seen on the interface in [chars] modeExplanation The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.
Recommended Action Ensure that the port is configured to use only one host. Enter the <Cmd>shutdown<Cmd> followed by <CmdBold>no shutdown<CmdBold> command to restart the port.
Error Message DOT1X-5-SECURITY_VIOLATION: New MAC address [chars] is seen on interface [chars] in [chars] modeExplanation The port on the interface specified in the error message is configured in single host mode. Any new host that is detected on the interface is treated as a security violation. The port has been Error disabled.
Recommended Action Ensure that the port is configured to use only one host. Enter the <Cmd>shutdown<Cmd> followed by <CmdBold>no shutdown<CmdBold> command to restart the port.
Error Message DOT1X-5-SESSION_CREATION: Dot1x authentication session initiated in interface [chars] using authentication method [chars]Explanation Dot1x authentication session has been created after successful authentication of supplicannot.
Recommended Action No action is required.
Error Message DOT1X-5-SESSION_TERMINATION: Dot1x authentication session in interface [chars] using authentication method [chars] is terminated because of [chars]Explanation Dot1x authentication session has been terminated.
Recommended Action No action is required.
Error Message DOT1X-5-SESSION_TERMINATION: Dot1x authentication session in interface [chars] using authentication method [chars] is terminated because of [chars] and port moved to [chars] stateExplanation Dot1x authentication session has been terminated.
Recommended Action No action is required.
Error Message DOT1X-5-STATUS: Dot1x interface [chars] status changed from [chars] to [chars]Explanation Dot1x authenticator has changed its internal state.
Recommended Action No action is required.
DPP_DEBUG Messages
This section contains the DPP_DEBUG messages.
DPP_DEBUG-2
Error Message DPP_DEBUG-2-DPP_CRIT: [DPP[dec]] [chars]Explanation A DPP generated a critical message.
Recommended Action No action is required.
DPVM Messages
This section contains the DPVM messages.
DPVM-2
Error Message DPVM-2-ALLOC_FAILED: Memory allocation failed for size:[dec] for [chars]Explanation Memory allocation failed for size [dec] for [chars].
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-2-DPVM_DUPL_REJECT: [chars]Explanation Rejected duplicate pwwn query.
Recommended Action Dpvm overwrite-duplicate-pwwn.
DPVM-3
Error Message DPVM-3-DB_ERR: [chars]Explanation An error occurred during an DPVM database operation. [chars] indicates the reason for the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-DDAS_MODE_INVALID: [chars]Explanation DDAS mode Invalid. [chars].
Recommended Action Flip DDAS mode.
Error Message DPVM-3-INIT_FAIL: [chars]Explanation An error occurred during DPVM Initialization. [chars] indicates the reason for failure.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-MTS_ERR: [chars]Explanation An error occurred in processing of an MTS message. [chars] indicates the error that occurred.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
Error Message DPVM-3-PSS_ERR: [chars]Explanation An error occurred during an DPVM PSS operation. [chars] indicates the PSS operation that caused the error.
Recommended Action Contact the Cisco Technical Assistance Center (TAC) through the Cisco Support web site http://www.cisco.com/tac.
DPVM-4
Error Message DPVM-4-ACTIVATION_FAIL: [chars]Explanation Activation of DPVM device mappings failed due to [chars].
Recommended Action Correct the error and reactivate database again.
Error Message DPVM-4-FEATURE_DISABLED: [chars]Explanation DPVM is unavailable and disabled now.
Recommended Action No action is required.
DPVM-6
Error Message DPVM-6-FEATURE_ENABLED: [chars]Explanation DPVM is available and enabled now.
Recommended Action No action is required.
Error Message